Merge tag 'mvebu-dt-3.14-2' of git://git.infradead.org/linux-mvebu into next/dt
From Jason Cooper:
mvebu DT changes for v3.14 (set #2)
- mvebu
- Netgear ReadyNAS cleanup
- add Netgear ReadyNAS 2120
- kirkwood
- Netgear ReadyNAS cleanup
- add Netgear ReadyNAS NV+ v2
* tag 'mvebu-dt-3.14-2' of git://git.infradead.org/linux-mvebu:
ARM: kirkwood: Add support for NETGEAR ReadyNAS NV+ v2
ARM: mvebu: Add Netgear ReadyNAS 2120 board
ARM: mvebu: Fix whitespace in NETGEAR ReadyNAS .dts files
ARM: mvebu: NETGEAR ReadyNAS 104 .dts cleanup
ARM: mvebu: NETGEAR ReadyNAS 102 .dts cleanup
ARM: kirkwood: NETGEAR ReadyNAS Duo v2 .dts cleanup
Signed-off-by: Kevin Hilman <khilman@linaro.org>
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index d57c1a6..adcc606 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -90,6 +90,7 @@
kirkwood-mplcec4.dtb \
kirkwood-mv88f6281gtw-ge.dtb \
kirkwood-netgear_readynas_duo_v2.dtb \
+ kirkwood-netgear_readynas_nv+_v2.dtb \
kirkwood-ns2.dtb \
kirkwood-ns2lite.dtb \
kirkwood-ns2max.dtb \
@@ -114,6 +115,7 @@
armada-xp-axpwifiap.dtb \
armada-xp-db.dtb \
armada-xp-gp.dtb \
+ armada-xp-netgear-rn2120.dtb \
armada-xp-matrix.dtb \
armada-xp-openblocks-ax3-4.dtb
dtb-$(CONFIG_ARCH_MXC) += \
diff --git a/arch/arm/boot/dts/armada-370-netgear-rn102.dts b/arch/arm/boot/dts/armada-370-netgear-rn102.dts
index df1a1e0..1c2d13d 100644
--- a/arch/arm/boot/dts/armada-370-netgear-rn102.dts
+++ b/arch/arm/boot/dts/armada-370-netgear-rn102.dts
@@ -11,6 +11,8 @@
/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
#include "armada-370.dtsi"
/ {
@@ -62,6 +64,7 @@
marvell,pins = "mpp57";
marvell,function = "gpio";
};
+
sata1_led_pin: sata1-led-pin {
marvell,pins = "mpp15";
marvell,function = "gpio";
@@ -77,6 +80,21 @@
marvell,function = "gpio";
};
+ backup_button_pin: backup-button-pin {
+ marvell,pins = "mpp58";
+ marvell,function = "gpio";
+ };
+
+ power_button_pin: power-button-pin {
+ marvell,pins = "mpp62";
+ marvell,function = "gpio";
+ };
+
+ reset_button_pin: reset-button-pin {
+ marvell,pins = "mpp6";
+ marvell,function = "gpio";
+ };
+
poweroff: poweroff {
marvell,pins = "mpp8";
marvell,function = "gpio";
@@ -84,7 +102,7 @@
};
mdio {
- phy0: ethernet-phy@0 {
+ phy0: ethernet-phy@0 { /* Marvell 88E1318 */
reg = <0>;
};
};
@@ -117,78 +135,76 @@
};
clocks {
- #address-cells = <1>;
- #size-cells = <0>;
-
- g762_clk: fixedclk {
+ g762_clk: g762-oscillator {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <8192>;
};
};
- gpio_leds {
+ gpio-leds {
compatible = "gpio-leds";
- pinctrl-0 = < &power_led_pin
- &sata1_led_pin
- &sata2_led_pin
- &backup_led_pin >;
+ pinctrl-0 = <&power_led_pin
+ &sata1_led_pin
+ &sata2_led_pin
+ &backup_led_pin>;
pinctrl-names = "default";
- blue_power_led {
+ blue-power-led {
label = "rn102:blue:pwr";
- gpios = <&gpio1 25 1>; /* GPIO 57 Active Low */
+ gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
default-state = "keep";
};
- green_sata1_led {
+ green-sata1-led {
label = "rn102:green:sata1";
- gpios = <&gpio0 15 1>; /* GPIO 15 Active Low */
+ gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
default-state = "on";
};
- green_sata2_led {
+ green-sata2-led {
label = "rn102:green:sata2";
- gpios = <&gpio0 14 1>; /* GPIO 14 Active Low */
+ gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
default-state = "on";
};
- green_backup_led {
+ green-backup-led {
label = "rn102:green:backup";
- gpios = <&gpio1 24 1>; /* GPIO 56 Active Low */
+ gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
default-state = "on";
};
};
- gpio_keys {
+ gpio-keys {
compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
+ pinctrl-0 = <&power_button_pin
+ &reset_button_pin
+ &backup_button_pin>;
+ pinctrl-names = "default";
- button@1 {
+ power-button {
label = "Power Button";
- linux,code = <116>; /* KEY_POWER */
- gpios = <&gpio1 30 0>;
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
};
- button@2 {
+ reset-button {
label = "Reset Button";
- linux,code = <0x198>; /* KEY_RESTART */
- gpios = <&gpio0 6 1>;
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
};
- button@3 {
+ backup-button {
label = "Backup Button";
- linux,code = <133>; /* KEY_COPY */
- gpios = <&gpio1 26 1>;
+ linux,code = <KEY_COPY>;
+ gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
};
};
- gpio_poweroff {
+ gpio-poweroff {
compatible = "gpio-poweroff";
pinctrl-0 = <&poweroff>;
pinctrl-names = "default";
- gpios = <&gpio0 8 1>;
+ gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
};
-
};
diff --git a/arch/arm/boot/dts/armada-370-netgear-rn104.dts b/arch/arm/boot/dts/armada-370-netgear-rn104.dts
index 50b5150..e48e5fb 100644
--- a/arch/arm/boot/dts/armada-370-netgear-rn104.dts
+++ b/arch/arm/boot/dts/armada-370-netgear-rn104.dts
@@ -11,8 +11,9 @@
/dts-v1/;
-#include "armada-370.dtsi"
+#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
+#include "armada-370.dtsi"
/ {
model = "NETGEAR ReadyNAS 104";
@@ -59,12 +60,12 @@
marvell,function = "gpio";
};
- backup_key_pin: backup-key-pin {
+ backup_button_pin: backup-button-pin {
marvell,pins = "mpp52";
marvell,function = "gpio";
};
- power_key_pin: power-key-pin {
+ power_button_pin: power-button-pin {
marvell,pins = "mpp62";
marvell,function = "gpio";
};
@@ -79,18 +80,18 @@
marvell,function = "gpio";
};
- reset_key_pin: reset-key-pin {
+ reset_button_pin: reset-button-pin {
marvell,pins = "mpp65";
marvell,function = "gpio";
};
};
mdio {
- phy0: ethernet-phy@0 {
+ phy0: ethernet-phy@0 { /* Marvell 88E1318 */
reg = <0>;
};
- phy1: ethernet-phy@1 {
+ phy1: ethernet-phy@1 { /* Marvell 88E1318 */
reg = <1>;
};
};
@@ -136,90 +137,85 @@
};
clocks {
- #address-cells = <1>;
- #size-cells = <0>;
-
- g762_clk: fixedclk {
+ g762_clk: g762-oscillator {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <8192>;
};
};
- gpio_leds {
+ gpio-leds {
compatible = "gpio-leds";
pinctrl-0 = <&backup_led_pin &power_led_pin>;
pinctrl-names = "default";
- blue_backup_led {
+ blue-backup-led {
label = "rn104:blue:backup";
- gpios = <&gpio1 31 0>; /* GPIO 63 Active High */
+ gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
- blue_power_led {
+ blue-power-led {
label = "rn104:blue:pwr";
- gpios = <&gpio2 0 1>; /* GPIO 64 Active Low */
+ gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
linux,default-trigger = "keep";
};
- sata1_led {
+ blue-sata1-led {
label = "rn104:blue:sata1";
gpios = <&pca9554 0 GPIO_ACTIVE_LOW>;
default-state = "off";
};
- sata2_led {
+ blue-sata2-led {
label = "rn104:blue:sata2";
gpios = <&pca9554 1 GPIO_ACTIVE_LOW>;
default-state = "off";
};
- sata3_led {
+ blue-sata3-led {
label = "rn104:blue:sata3";
gpios = <&pca9554 2 GPIO_ACTIVE_LOW>;
default-state = "off";
};
- sata4_led {
+ blue-sata4-led {
label = "rn104:blue:sata4";
gpios = <&pca9554 3 GPIO_ACTIVE_LOW>;
default-state = "off";
};
};
- gpio_keys {
+ gpio-keys {
compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
- pinctrl-0 = <&backup_key_pin
- &power_key_pin
- &reset_key_pin>;
+ pinctrl-0 = <&backup_button_pin
+ &power_button_pin
+ &reset_button_pin>;
pinctrl-names = "default";
- button@1 {
+ backup-button {
label = "Backup Button";
- linux,code = <133>; /* KEY_COPY */
- gpios = <&gpio1 20 1>;
+ linux,code = <KEY_COPY>;
+ gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
};
- button@2 {
+ power-button {
label = "Power Button";
- linux,code = <116>; /* KEY_POWER */
- gpios = <&gpio1 30 0>;
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
};
- button@3 {
+ reset-button {
label = "Reset Button";
- linux,code = <0x198>; /* KEY_RESTART */
- gpios = <&gpio2 1 1>;
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
};
};
- gpio_poweroff {
+ gpio-poweroff {
compatible = "gpio-poweroff";
pinctrl-0 = <&poweroff>;
pinctrl-names = "default";
- gpios = <&gpio1 28 1>;
+ gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
};
};
diff --git a/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts b/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts
new file mode 100644
index 0000000..8b2a787
--- /dev/null
+++ b/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts
@@ -0,0 +1,286 @@
+/*
+ * Device Tree file for NETGEAR ReadyNAS 2120
+ *
+ * Copyright (C) 2013, Arnaud EBALARD <arno@natisbad.org>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-xp-mv78230.dtsi"
+
+/ {
+ model = "NETGEAR ReadyNAS 2120";
+ compatible = "netgear,readynas-2120", "marvell,armadaxp-mv78230", "marvell,armadaxp", "marvell,armada-370-xp";
+
+ chosen {
+ bootargs = "console=ttyS0,115200 earlyprintk";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x00000000 0 0x80000000>; /* 2GB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>;
+
+ pcie-controller {
+ status = "okay";
+
+ /* Connected to first Marvell 88SE9170 SATA controller */
+ pcie@1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+
+ /* Connected to second Marvell 88SE9170 SATA controller */
+ pcie@2,0 {
+ /* Port 0, Lane 1 */
+ status = "okay";
+ };
+
+ /* Connected to Fresco Logic FL1009 USB 3.0 controller */
+ pcie@5,0 {
+ /* Port 1, Lane 0 */
+ status = "okay";
+ };
+ };
+
+ internal-regs {
+ pinctrl {
+ poweroff: poweroff {
+ marvell,pins = "mpp42";
+ marvell,function = "gpio";
+ };
+
+ power_button_pin: power-button-pin {
+ marvell,pins = "mpp27";
+ marvell,function = "gpio";
+ };
+
+ reset_button_pin: reset-button-pin {
+ marvell,pins = "mpp41";
+ marvell,function = "gpio";
+ };
+
+ sata1_led_pin: sata1-led-pin {
+ marvell,pins = "mpp31";
+ marvell,function = "gpio";
+ };
+
+ sata2_led_pin: sata2-led-pin {
+ marvell,pins = "mpp40";
+ marvell,function = "gpio";
+ };
+
+ sata3_led_pin: sata3-led-pin {
+ marvell,pins = "mpp44";
+ marvell,function = "gpio";
+ };
+
+ sata4_led_pin: sata4-led-pin {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+
+ sata1_power_pin: sata1-power-pin {
+ marvell,pins = "mpp24";
+ marvell,function = "gpio";
+ };
+
+ sata2_power_pin: sata2-power-pin {
+ marvell,pins = "mpp25";
+ marvell,function = "gpio";
+ };
+
+ sata3_power_pin: sata3-power-pin {
+ marvell,pins = "mpp26";
+ marvell,function = "gpio";
+ };
+
+ sata4_power_pin: sata4-power-pin {
+ marvell,pins = "mpp28";
+ marvell,function = "gpio";
+ };
+
+ sata1_pres_pin: sata1-pres-pin {
+ marvell,pins = "mpp32";
+ marvell,function = "gpio";
+ };
+
+ sata2_pres_pin: sata2-pres-pin {
+ marvell,pins = "mpp33";
+ marvell,function = "gpio";
+ };
+
+ sata3_pres_pin: sata3-pres-pin {
+ marvell,pins = "mpp34";
+ marvell,function = "gpio";
+ };
+
+ sata4_pres_pin: sata4-pres-pin {
+ marvell,pins = "mpp35";
+ marvell,function = "gpio";
+ };
+
+ err_led_pin: err-led-pin {
+ marvell,pins = "mpp45";
+ marvell,function = "gpio";
+ };
+ };
+
+ serial@12000 {
+ clocks = <&coreclk 0>;
+ status = "okay";
+ };
+
+ mdio {
+ phy0: ethernet-phy@0 { /* Marvell 88E1318 */
+ reg = <0>;
+ };
+
+ phy1: ethernet-phy@1 { /* Marvell 88E1318 */
+ reg = <1>;
+ };
+ };
+
+ ethernet@70000 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+ };
+
+ ethernet@74000 {
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "rgmii-id";
+ };
+
+ /* Front USB 2.0 port */
+ usb@50000 {
+ status = "okay";
+ };
+
+ i2c@11000 {
+ compatible = "marvell,mv64xxx-i2c";
+ clock-frequency = <400000>;
+ status = "okay";
+
+ /* Controller for rear fan #1 of 3 (Protechnic
+ * MGT4012XB-O20, 8000RPM) near eSATA port */
+ g762_fan1: g762@3e {
+ compatible = "gmt,g762";
+ reg = <0x3e>;
+ clocks = <&g762_clk>; /* input clock */
+ fan_gear_mode = <0>;
+ fan_startv = <1>;
+ pwm_polarity = <0>;
+ };
+
+ /* Controller for rear (center) fan #2 of 3 */
+ g762_fan2: g762@48 {
+ compatible = "gmt,g762";
+ reg = <0x48>;
+ clocks = <&g762_clk>; /* input clock */
+ fan_gear_mode = <0>;
+ fan_startv = <1>;
+ pwm_polarity = <0>;
+ };
+
+ /* Controller for rear fan #3 of 3 */
+ g762_fan3: g762@49 {
+ compatible = "gmt,g762";
+ reg = <0x49>;
+ clocks = <&g762_clk>; /* input clock */
+ fan_gear_mode = <0>;
+ fan_startv = <1>;
+ pwm_polarity = <0>;
+ };
+
+ /* Temperature sensor */
+ g751: g751@4c {
+ compatible = "gmt,g751";
+ reg = <0x4c>;
+ };
+ };
+ };
+ };
+
+ clocks {
+ g762_clk: g762-oscillator {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&sata1_led_pin &sata2_led_pin &err_led_pin
+ &sata3_led_pin &sata4_led_pin>;
+ pinctrl-names = "default";
+
+ red-sata1-led {
+ label = "rn2120:red:sata1";
+ gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ red-sata2-led {
+ label = "rn2120:red:sata2";
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ red-sata3-led {
+ label = "rn2120:red:sata3";
+ gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ red-sata4-led {
+ label = "rn2120:red:sata4";
+ gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ red-err-led {
+ label = "rn2120:red:err";
+ gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&power_button_pin &reset_button_pin>;
+ pinctrl-names = "default";
+
+ power-button {
+ label = "Power Button";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>;
+ };
+
+ reset-button {
+ label = "Reset Button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-poweroff {
+ compatible = "gpio-poweroff";
+ pinctrl-0 = <&poweroff>;
+ pinctrl-names = "default";
+ gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+ };
+};
diff --git a/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts b/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts
index 3627702..3b1a365 100644
--- a/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts
+++ b/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts
@@ -1,5 +1,17 @@
+/*
+ * Device Tree file for NETGEAR ReadyNAS Duo v2
+ *
+ * Copyright (C) 2013, Arnaud EBALARD <arno@natisbad.org>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
/dts-v1/;
+#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
#include "kirkwood.dtsi"
#include "kirkwood-6282.dtsi"
@@ -33,34 +45,42 @@
marvell,pins = "mpp47";
marvell,function = "gpio";
};
+
pmx_button_backup: pmx-button-backup {
marvell,pins = "mpp45";
marvell,function = "gpio";
};
+
pmx_button_reset: pmx-button-reset {
marvell,pins = "mpp13";
marvell,function = "gpio";
};
+
pmx_led_blue_power: pmx-led-blue-power {
marvell,pins = "mpp31";
marvell,function = "gpio";
};
+
pmx_led_blue_activity: pmx-led-blue-activity {
marvell,pins = "mpp38";
marvell,function = "gpio";
};
+
pmx_led_blue_disk1: pmx-led-blue-disk1 {
marvell,pins = "mpp23";
marvell,function = "gpio";
};
+
pmx_led_blue_disk2: pmx-led-blue-disk2 {
marvell,pins = "mpp22";
marvell,function = "gpio";
};
+
pmx_led_blue_backup: pmx-led-blue-backup {
marvell,pins = "mpp29";
marvell,function = "gpio";
};
+
pmx_poweroff: pmx-poweroff {
marvell,pins = "mpp30";
marvell,function = "gpio";
@@ -68,10 +88,7 @@
};
clocks {
- #address-cells = <1>;
- #size-cells = <0>;
-
- g762_clk: fixedclk {
+ g762_clk: g762-oscillator {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <8192>;
@@ -117,49 +134,53 @@
power_led {
label = "status:blue:power_led";
- gpios = <&gpio0 31 1>; /* GPIO 31 Active Low */
+ gpios = <&gpio0 31 GPIO_ACTIVE_LOW>;
default-state = "keep";
};
+
activity_led {
label = "status:blue:activity_led";
- gpios = <&gpio1 6 1>; /* GPIO 38 Active Low */
+ gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
};
+
disk1_led {
label = "status:blue:disk1_led";
- gpios = <&gpio0 23 1>; /* GPIO 23 Active Low */
+ gpios = <&gpio0 23 GPIO_ACTIVE_LOW>;
};
+
disk2_led {
label = "status:blue:disk2_led";
- gpios = <&gpio0 22 1>; /* GPIO 22 Active Low */
+ gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
};
+
backup_led {
label = "status:blue:backup_led";
- gpios = <&gpio0 29 1>; /* GPIO 29 Active Low*/
+ gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
};
};
- gpio_keys {
+ gpio-keys {
compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
pinctrl-0 = <&pmx_button_power &pmx_button_backup
&pmx_button_reset>;
pinctrl-names = "default";
- button@1 {
+ power-button {
label = "Power Button";
- linux,code = <116>; /* KEY_POWER */
- gpios = <&gpio1 15 1>;
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
};
- button@2 {
+
+ reset-button {
label = "Reset Button";
- linux,code = <0x198>; /* KEY_RESTART */
- gpios = <&gpio0 13 1>;
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
};
- button@3 {
+
+ backup-button {
label = "Backup Button";
- linux,code = <133>; /* KEY_COPY */
- gpios = <&gpio1 13 1>;
+ linux,code = <KEY_COPY>;
+ gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
};
};
@@ -170,23 +191,23 @@
gpios = <&gpio0 30 GPIO_ACTIVE_LOW>;
};
- regulators {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
- usb_power: regulator@1 {
- compatible = "regulator-fixed";
- reg = <1>;
- regulator-name = "USB 3.0 Power";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- enable-active-high;
- regulator-always-on;
- regulator-boot-on;
- gpio = <&gpio1 14 0>;
- };
- };
+ usb3_regulator: usb3-regulator {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "USB 3.0 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+ };
+ };
};
&nand {
@@ -222,7 +243,7 @@
&mdio {
status = "okay";
- ethphy0: ethernet-phy@0 {
+ ethphy0: ethernet-phy@0 { /* Marvell 88E1318 */
device_type = "ethernet-phy";
reg = <0>;
};
diff --git a/arch/arm/boot/dts/kirkwood-netgear_readynas_nv+_v2.dts b/arch/arm/boot/dts/kirkwood-netgear_readynas_nv+_v2.dts
new file mode 100644
index 0000000..72a3883
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-netgear_readynas_nv+_v2.dts
@@ -0,0 +1,270 @@
+/*
+ * Device Tree file for NETGEAR ReadyNAS NV+ v2
+ *
+ * Copyright (C) 2013, Arnaud EBALARD <arno@natisbad.org>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "kirkwood.dtsi"
+#include "kirkwood-6282.dtsi"
+
+/ {
+ model = "NETGEAR ReadyNAS NV+ v2";
+ compatible = "netgear,readynas-nv+-v2", "netgear,readynas", "marvell,kirkwood-88f6282", "marvell,kirkwood";
+
+ memory { /* 256 MB */
+ device_type = "memory";
+ reg = <0x00000000 0x10000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk";
+ };
+
+ mbus {
+ pcie-controller {
+ status = "okay";
+
+ /* Connected to NEC uPD720200 USB 3.0 controller */
+ pcie@1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+ };
+ };
+
+ ocp@f1000000 {
+ pinctrl: pinctrl@10000 {
+ pmx_button_power: pmx-button-power {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+
+ pmx_button_backup: pmx-button-backup {
+ marvell,pins = "mpp45";
+ marvell,function = "gpio";
+ };
+
+ pmx_button_reset: pmx-button-reset {
+ marvell,pins = "mpp13";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_blue_power: pmx-led-blue-power {
+ marvell,pins = "mpp31";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_blue_backup: pmx-led-blue-backup {
+ marvell,pins = "mpp22";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_blue_disk1: pmx-led-blue-disk1 {
+ marvell,pins = "mpp20";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_blue_disk2: pmx-led-blue-disk2 {
+ marvell,pins = "mpp23";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_blue_disk3: pmx-led-blue-disk3 {
+ marvell,pins = "mpp24";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_blue_disk4: pmx-led-blue-disk4 {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+
+ pmx_poweroff: pmx-poweroff {
+ marvell,pins = "mpp30";
+ marvell,function = "gpio";
+ };
+ };
+
+ clocks {
+ g762_clk: g762-oscillator {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <8192>;
+ };
+ };
+
+ i2c@11000 {
+ status = "okay";
+
+ rs5c372a: rs5c372a@32 {
+ compatible = "ricoh,rs5c372a";
+ reg = <0x32>;
+ };
+
+ g762: g762@3e {
+ compatible = "gmt,g762";
+ reg = <0x3e>;
+ clocks = <&g762_clk>; /* input clock */
+ fan_gear_mode = <0>;
+ fan_startv = <1>;
+ pwm_polarity = <0>;
+ };
+ };
+
+ serial@12000 {
+ pinctrl-0 = <&pmx_uart0>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ sata@80000 { /* Connected to Marvell 88SM4140 SATA port multiplier */
+ status = "okay";
+ nr-ports = <1>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = < &pmx_led_blue_power &pmx_led_blue_backup
+ &pmx_led_blue_disk1 &pmx_led_blue_disk2
+ &pmx_led_blue_disk3 &pmx_led_blue_disk3 >;
+ pinctrl-names = "default";
+
+ power_led {
+ label = "status:blue:power_led";
+ gpios = <&gpio0 31 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "default-on";
+ };
+
+ backup_led {
+ label = "status:blue:backup_led";
+ gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
+ };
+
+ disk1_led {
+ label = "status:blue:disk1_led";
+ gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
+ };
+
+ disk2_led {
+ label = "status:blue:disk2_led";
+ gpios = <&gpio0 23 GPIO_ACTIVE_LOW>;
+ };
+
+ disk3_led {
+ label = "status:blue:disk3_led";
+ gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
+ };
+
+ disk4_led {
+ label = "status:blue:disk4_led";
+ gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&pmx_button_power &pmx_button_backup
+ &pmx_button_reset>;
+ pinctrl-names = "default";
+
+ power-button {
+ label = "Power Button";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ };
+
+ reset-button {
+ label = "Reset Button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+ };
+
+ backup-button {
+ label = "Backup Button";
+ linux,code = <KEY_COPY>;
+ gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-poweroff {
+ compatible = "gpio-poweroff";
+ pinctrl-0 = <&pmx_poweroff>;
+ pinctrl-names = "default";
+ gpios = <&gpio0 30 GPIO_ACTIVE_LOW>;
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb3_regulator: usb3-regulator {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "USB 3.0 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&nand {
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x180000>;
+ read-only;
+ };
+
+ partition@180000 {
+ label = "u-boot-env";
+ reg = <0x180000 0x20000>;
+ };
+
+ partition@200000 {
+ label = "uImage";
+ reg = <0x0200000 0x600000>;
+ };
+
+ partition@800000 {
+ label = "minirootfs";
+ reg = <0x0800000 0x1000000>;
+ };
+
+ partition@1800000 {
+ label = "jffs2";
+ reg = <0x1800000 0x6800000>;
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy@0 { /* Marvell 88E1318 */
+ device_type = "ethernet-phy";
+ reg = <0>;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ ethernet0-port@0 {
+ phy-handle = <ðphy0>;
+ };
+};