| /* |
| * linux/drivers/mmc/host/pxa.c - PXA MMCI driver |
| * |
| * Copyright (C) 2003 Russell King, All Rights Reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| * |
| * This hardware is really sick: |
| * - No way to clear interrupts. |
| * - Have to turn off the clock whenever we touch the device. |
| * - Doesn't tell you how many data blocks were transferred. |
| * Yuck! |
| * |
| * 1 and 3 byte data transfers not supported |
| * max block length up to 1023 |
| */ |
| #include <linux/module.h> |
| #include <linux/init.h> |
| #include <linux/ioport.h> |
| #include <linux/platform_device.h> |
| #include <linux/delay.h> |
| #include <linux/interrupt.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/clk.h> |
| #include <linux/err.h> |
| #include <linux/mmc/host.h> |
| #include <linux/io.h> |
| #include <linux/regulator/consumer.h> |
| #include <linux/gpio.h> |
| #include <linux/gfp.h> |
| #include <linux/of.h> |
| #include <linux/of_gpio.h> |
| #include <linux/of_device.h> |
| |
| #include <asm/sizes.h> |
| |
| #include <mach/hardware.h> |
| #include <mach/dma.h> |
| #include <linux/platform_data/mmc-pxamci.h> |
| |
| #include "pxamci.h" |
| |
| #define DRIVER_NAME "pxa2xx-mci" |
| |
| #define NR_SG 1 |
| #define CLKRT_OFF (~0) |
| |
| #define mmc_has_26MHz() (cpu_is_pxa300() || cpu_is_pxa310() \ |
| || cpu_is_pxa935()) |
| |
| struct pxamci_host { |
| struct mmc_host *mmc; |
| spinlock_t lock; |
| struct resource *res; |
| void __iomem *base; |
| struct clk *clk; |
| unsigned long clkrate; |
| int irq; |
| int dma; |
| unsigned int clkrt; |
| unsigned int cmdat; |
| unsigned int imask; |
| unsigned int power_mode; |
| struct pxamci_platform_data *pdata; |
| |
| struct mmc_request *mrq; |
| struct mmc_command *cmd; |
| struct mmc_data *data; |
| |
| dma_addr_t sg_dma; |
| struct pxa_dma_desc *sg_cpu; |
| unsigned int dma_len; |
| |
| unsigned int dma_dir; |
| unsigned int dma_drcmrrx; |
| unsigned int dma_drcmrtx; |
| |
| struct regulator *vcc; |
| }; |
| |
| static inline void pxamci_init_ocr(struct pxamci_host *host) |
| { |
| #ifdef CONFIG_REGULATOR |
| host->vcc = regulator_get(mmc_dev(host->mmc), "vmmc"); |
| |
| if (IS_ERR(host->vcc)) |
| host->vcc = NULL; |
| else { |
| host->mmc->ocr_avail = mmc_regulator_get_ocrmask(host->vcc); |
| if (host->pdata && host->pdata->ocr_mask) |
| dev_warn(mmc_dev(host->mmc), |
| "ocr_mask/setpower will not be used\n"); |
| } |
| #endif |
| if (host->vcc == NULL) { |
| /* fall-back to platform data */ |
| host->mmc->ocr_avail = host->pdata ? |
| host->pdata->ocr_mask : |
| MMC_VDD_32_33 | MMC_VDD_33_34; |
| } |
| } |
| |
| static inline int pxamci_set_power(struct pxamci_host *host, |
| unsigned char power_mode, |
| unsigned int vdd) |
| { |
| int on; |
| |
| if (host->vcc) { |
| int ret; |
| |
| if (power_mode == MMC_POWER_UP) { |
| ret = mmc_regulator_set_ocr(host->mmc, host->vcc, vdd); |
| if (ret) |
| return ret; |
| } else if (power_mode == MMC_POWER_OFF) { |
| ret = mmc_regulator_set_ocr(host->mmc, host->vcc, 0); |
| if (ret) |
| return ret; |
| } |
| } |
| if (!host->vcc && host->pdata && |
| gpio_is_valid(host->pdata->gpio_power)) { |
| on = ((1 << vdd) & host->pdata->ocr_mask); |
| gpio_set_value(host->pdata->gpio_power, |
| !!on ^ host->pdata->gpio_power_invert); |
| } |
| if (!host->vcc && host->pdata && host->pdata->setpower) |
| return host->pdata->setpower(mmc_dev(host->mmc), vdd); |
| |
| return 0; |
| } |
| |
| static void pxamci_stop_clock(struct pxamci_host *host) |
| { |
| if (readl(host->base + MMC_STAT) & STAT_CLK_EN) { |
| unsigned long timeout = 10000; |
| unsigned int v; |
| |
| writel(STOP_CLOCK, host->base + MMC_STRPCL); |
| |
| do { |
| v = readl(host->base + MMC_STAT); |
| if (!(v & STAT_CLK_EN)) |
| break; |
| udelay(1); |
| } while (timeout--); |
| |
| if (v & STAT_CLK_EN) |
| dev_err(mmc_dev(host->mmc), "unable to stop clock\n"); |
| } |
| } |
| |
| static void pxamci_enable_irq(struct pxamci_host *host, unsigned int mask) |
| { |
| unsigned long flags; |
| |
| spin_lock_irqsave(&host->lock, flags); |
| host->imask &= ~mask; |
| writel(host->imask, host->base + MMC_I_MASK); |
| spin_unlock_irqrestore(&host->lock, flags); |
| } |
| |
| static void pxamci_disable_irq(struct pxamci_host *host, unsigned int mask) |
| { |
| unsigned long flags; |
| |
| spin_lock_irqsave(&host->lock, flags); |
| host->imask |= mask; |
| writel(host->imask, host->base + MMC_I_MASK); |
| spin_unlock_irqrestore(&host->lock, flags); |
| } |
| |
| static void pxamci_setup_data(struct pxamci_host *host, struct mmc_data *data) |
| { |
| unsigned int nob = data->blocks; |
| unsigned long long clks; |
| unsigned int timeout; |
| bool dalgn = 0; |
| u32 dcmd; |
| int i; |
| |
| host->data = data; |
| |
| if (data->flags & MMC_DATA_STREAM) |
| nob = 0xffff; |
| |
| writel(nob, host->base + MMC_NOB); |
| writel(data->blksz, host->base + MMC_BLKLEN); |
| |
| clks = (unsigned long long)data->timeout_ns * host->clkrate; |
| do_div(clks, 1000000000UL); |
| timeout = (unsigned int)clks + (data->timeout_clks << host->clkrt); |
| writel((timeout + 255) / 256, host->base + MMC_RDTO); |
| |
| if (data->flags & MMC_DATA_READ) { |
| host->dma_dir = DMA_FROM_DEVICE; |
| dcmd = DCMD_INCTRGADDR | DCMD_FLOWSRC; |
| DRCMR(host->dma_drcmrtx) = 0; |
| DRCMR(host->dma_drcmrrx) = host->dma | DRCMR_MAPVLD; |
| } else { |
| host->dma_dir = DMA_TO_DEVICE; |
| dcmd = DCMD_INCSRCADDR | DCMD_FLOWTRG; |
| DRCMR(host->dma_drcmrrx) = 0; |
| DRCMR(host->dma_drcmrtx) = host->dma | DRCMR_MAPVLD; |
| } |
| |
| dcmd |= DCMD_BURST32 | DCMD_WIDTH1; |
| |
| host->dma_len = dma_map_sg(mmc_dev(host->mmc), data->sg, data->sg_len, |
| host->dma_dir); |
| |
| for (i = 0; i < host->dma_len; i++) { |
| unsigned int length = sg_dma_len(&data->sg[i]); |
| host->sg_cpu[i].dcmd = dcmd | length; |
| if (length & 31 && !(data->flags & MMC_DATA_READ)) |
| host->sg_cpu[i].dcmd |= DCMD_ENDIRQEN; |
| /* Not aligned to 8-byte boundary? */ |
| if (sg_dma_address(&data->sg[i]) & 0x7) |
| dalgn = 1; |
| if (data->flags & MMC_DATA_READ) { |
| host->sg_cpu[i].dsadr = host->res->start + MMC_RXFIFO; |
| host->sg_cpu[i].dtadr = sg_dma_address(&data->sg[i]); |
| } else { |
| host->sg_cpu[i].dsadr = sg_dma_address(&data->sg[i]); |
| host->sg_cpu[i].dtadr = host->res->start + MMC_TXFIFO; |
| } |
| host->sg_cpu[i].ddadr = host->sg_dma + (i + 1) * |
| sizeof(struct pxa_dma_desc); |
| } |
| host->sg_cpu[host->dma_len - 1].ddadr = DDADR_STOP; |
| wmb(); |
| |
| /* |
| * The PXA27x DMA controller encounters overhead when working with |
| * unaligned (to 8-byte boundaries) data, so switch on byte alignment |
| * mode only if we have unaligned data. |
| */ |
| if (dalgn) |
| DALGN |= (1 << host->dma); |
| else |
| DALGN &= ~(1 << host->dma); |
| DDADR(host->dma) = host->sg_dma; |
| |
| /* |
| * workaround for erratum #91: |
| * only start DMA now if we are doing a read, |
| * otherwise we wait until CMD/RESP has finished |
| * before starting DMA. |
| */ |
| if (!cpu_is_pxa27x() || data->flags & MMC_DATA_READ) |
| DCSR(host->dma) = DCSR_RUN; |
| } |
| |
| static void pxamci_start_cmd(struct pxamci_host *host, struct mmc_command *cmd, unsigned int cmdat) |
| { |
| WARN_ON(host->cmd != NULL); |
| host->cmd = cmd; |
| |
| if (cmd->flags & MMC_RSP_BUSY) |
| cmdat |= CMDAT_BUSY; |
| |
| #define RSP_TYPE(x) ((x) & ~(MMC_RSP_BUSY|MMC_RSP_OPCODE)) |
| switch (RSP_TYPE(mmc_resp_type(cmd))) { |
| case RSP_TYPE(MMC_RSP_R1): /* r1, r1b, r6, r7 */ |
| cmdat |= CMDAT_RESP_SHORT; |
| break; |
| case RSP_TYPE(MMC_RSP_R3): |
| cmdat |= CMDAT_RESP_R3; |
| break; |
| case RSP_TYPE(MMC_RSP_R2): |
| cmdat |= CMDAT_RESP_R2; |
| break; |
| default: |
| break; |
| } |
| |
| writel(cmd->opcode, host->base + MMC_CMD); |
| writel(cmd->arg >> 16, host->base + MMC_ARGH); |
| writel(cmd->arg & 0xffff, host->base + MMC_ARGL); |
| writel(cmdat, host->base + MMC_CMDAT); |
| writel(host->clkrt, host->base + MMC_CLKRT); |
| |
| writel(START_CLOCK, host->base + MMC_STRPCL); |
| |
| pxamci_enable_irq(host, END_CMD_RES); |
| } |
| |
| static void pxamci_finish_request(struct pxamci_host *host, struct mmc_request *mrq) |
| { |
| host->mrq = NULL; |
| host->cmd = NULL; |
| host->data = NULL; |
| mmc_request_done(host->mmc, mrq); |
| } |
| |
| static int pxamci_cmd_done(struct pxamci_host *host, unsigned int stat) |
| { |
| struct mmc_command *cmd = host->cmd; |
| int i; |
| u32 v; |
| |
| if (!cmd) |
| return 0; |
| |
| host->cmd = NULL; |
| |
| /* |
| * Did I mention this is Sick. We always need to |
| * discard the upper 8 bits of the first 16-bit word. |
| */ |
| v = readl(host->base + MMC_RES) & 0xffff; |
| for (i = 0; i < 4; i++) { |
| u32 w1 = readl(host->base + MMC_RES) & 0xffff; |
| u32 w2 = readl(host->base + MMC_RES) & 0xffff; |
| cmd->resp[i] = v << 24 | w1 << 8 | w2 >> 8; |
| v = w2; |
| } |
| |
| if (stat & STAT_TIME_OUT_RESPONSE) { |
| cmd->error = -ETIMEDOUT; |
| } else if (stat & STAT_RES_CRC_ERR && cmd->flags & MMC_RSP_CRC) { |
| /* |
| * workaround for erratum #42: |
| * Intel PXA27x Family Processor Specification Update Rev 001 |
| * A bogus CRC error can appear if the msb of a 136 bit |
| * response is a one. |
| */ |
| if (cpu_is_pxa27x() && |
| (cmd->flags & MMC_RSP_136 && cmd->resp[0] & 0x80000000)) |
| pr_debug("ignoring CRC from command %d - *risky*\n", cmd->opcode); |
| else |
| cmd->error = -EILSEQ; |
| } |
| |
| pxamci_disable_irq(host, END_CMD_RES); |
| if (host->data && !cmd->error) { |
| pxamci_enable_irq(host, DATA_TRAN_DONE); |
| /* |
| * workaround for erratum #91, if doing write |
| * enable DMA late |
| */ |
| if (cpu_is_pxa27x() && host->data->flags & MMC_DATA_WRITE) |
| DCSR(host->dma) = DCSR_RUN; |
| } else { |
| pxamci_finish_request(host, host->mrq); |
| } |
| |
| return 1; |
| } |
| |
| static int pxamci_data_done(struct pxamci_host *host, unsigned int stat) |
| { |
| struct mmc_data *data = host->data; |
| |
| if (!data) |
| return 0; |
| |
| DCSR(host->dma) = 0; |
| dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len, |
| host->dma_dir); |
| |
| if (stat & STAT_READ_TIME_OUT) |
| data->error = -ETIMEDOUT; |
| else if (stat & (STAT_CRC_READ_ERROR|STAT_CRC_WRITE_ERROR)) |
| data->error = -EILSEQ; |
| |
| /* |
| * There appears to be a hardware design bug here. There seems to |
| * be no way to find out how much data was transferred to the card. |
| * This means that if there was an error on any block, we mark all |
| * data blocks as being in error. |
| */ |
| if (!data->error) |
| data->bytes_xfered = data->blocks * data->blksz; |
| else |
| data->bytes_xfered = 0; |
| |
| pxamci_disable_irq(host, DATA_TRAN_DONE); |
| |
| host->data = NULL; |
| if (host->mrq->stop) { |
| pxamci_stop_clock(host); |
| pxamci_start_cmd(host, host->mrq->stop, host->cmdat); |
| } else { |
| pxamci_finish_request(host, host->mrq); |
| } |
| |
| return 1; |
| } |
| |
| static irqreturn_t pxamci_irq(int irq, void *devid) |
| { |
| struct pxamci_host *host = devid; |
| unsigned int ireg; |
| int handled = 0; |
| |
| ireg = readl(host->base + MMC_I_REG) & ~readl(host->base + MMC_I_MASK); |
| |
| if (ireg) { |
| unsigned stat = readl(host->base + MMC_STAT); |
| |
| pr_debug("PXAMCI: irq %08x stat %08x\n", ireg, stat); |
| |
| if (ireg & END_CMD_RES) |
| handled |= pxamci_cmd_done(host, stat); |
| if (ireg & DATA_TRAN_DONE) |
| handled |= pxamci_data_done(host, stat); |
| if (ireg & SDIO_INT) { |
| mmc_signal_sdio_irq(host->mmc); |
| handled = 1; |
| } |
| } |
| |
| return IRQ_RETVAL(handled); |
| } |
| |
| static void pxamci_request(struct mmc_host *mmc, struct mmc_request *mrq) |
| { |
| struct pxamci_host *host = mmc_priv(mmc); |
| unsigned int cmdat; |
| |
| WARN_ON(host->mrq != NULL); |
| |
| host->mrq = mrq; |
| |
| pxamci_stop_clock(host); |
| |
| cmdat = host->cmdat; |
| host->cmdat &= ~CMDAT_INIT; |
| |
| if (mrq->data) { |
| pxamci_setup_data(host, mrq->data); |
| |
| cmdat &= ~CMDAT_BUSY; |
| cmdat |= CMDAT_DATAEN | CMDAT_DMAEN; |
| if (mrq->data->flags & MMC_DATA_WRITE) |
| cmdat |= CMDAT_WRITE; |
| |
| if (mrq->data->flags & MMC_DATA_STREAM) |
| cmdat |= CMDAT_STREAM; |
| } |
| |
| pxamci_start_cmd(host, mrq->cmd, cmdat); |
| } |
| |
| static int pxamci_get_ro(struct mmc_host *mmc) |
| { |
| struct pxamci_host *host = mmc_priv(mmc); |
| |
| if (host->pdata && gpio_is_valid(host->pdata->gpio_card_ro)) { |
| if (host->pdata->gpio_card_ro_invert) |
| return !gpio_get_value(host->pdata->gpio_card_ro); |
| else |
| return gpio_get_value(host->pdata->gpio_card_ro); |
| } |
| if (host->pdata && host->pdata->get_ro) |
| return !!host->pdata->get_ro(mmc_dev(mmc)); |
| /* |
| * Board doesn't support read only detection; let the mmc core |
| * decide what to do. |
| */ |
| return -ENOSYS; |
| } |
| |
| static void pxamci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) |
| { |
| struct pxamci_host *host = mmc_priv(mmc); |
| |
| if (ios->clock) { |
| unsigned long rate = host->clkrate; |
| unsigned int clk = rate / ios->clock; |
| |
| if (host->clkrt == CLKRT_OFF) |
| clk_enable(host->clk); |
| |
| if (ios->clock == 26000000) { |
| /* to support 26MHz */ |
| host->clkrt = 7; |
| } else { |
| /* to handle (19.5MHz, 26MHz) */ |
| if (!clk) |
| clk = 1; |
| |
| /* |
| * clk might result in a lower divisor than we |
| * desire. check for that condition and adjust |
| * as appropriate. |
| */ |
| if (rate / clk > ios->clock) |
| clk <<= 1; |
| host->clkrt = fls(clk) - 1; |
| } |
| |
| /* |
| * we write clkrt on the next command |
| */ |
| } else { |
| pxamci_stop_clock(host); |
| if (host->clkrt != CLKRT_OFF) { |
| host->clkrt = CLKRT_OFF; |
| clk_disable(host->clk); |
| } |
| } |
| |
| if (host->power_mode != ios->power_mode) { |
| int ret; |
| |
| host->power_mode = ios->power_mode; |
| |
| ret = pxamci_set_power(host, ios->power_mode, ios->vdd); |
| if (ret) { |
| dev_err(mmc_dev(mmc), "unable to set power\n"); |
| /* |
| * The .set_ios() function in the mmc_host_ops |
| * struct return void, and failing to set the |
| * power should be rare so we print an error and |
| * return here. |
| */ |
| return; |
| } |
| |
| if (ios->power_mode == MMC_POWER_ON) |
| host->cmdat |= CMDAT_INIT; |
| } |
| |
| if (ios->bus_width == MMC_BUS_WIDTH_4) |
| host->cmdat |= CMDAT_SD_4DAT; |
| else |
| host->cmdat &= ~CMDAT_SD_4DAT; |
| |
| dev_dbg(mmc_dev(mmc), "PXAMCI: clkrt = %x cmdat = %x\n", |
| host->clkrt, host->cmdat); |
| } |
| |
| static void pxamci_enable_sdio_irq(struct mmc_host *host, int enable) |
| { |
| struct pxamci_host *pxa_host = mmc_priv(host); |
| |
| if (enable) |
| pxamci_enable_irq(pxa_host, SDIO_INT); |
| else |
| pxamci_disable_irq(pxa_host, SDIO_INT); |
| } |
| |
| static const struct mmc_host_ops pxamci_ops = { |
| .request = pxamci_request, |
| .get_ro = pxamci_get_ro, |
| .set_ios = pxamci_set_ios, |
| .enable_sdio_irq = pxamci_enable_sdio_irq, |
| }; |
| |
| static void pxamci_dma_irq(int dma, void *devid) |
| { |
| struct pxamci_host *host = devid; |
| int dcsr = DCSR(dma); |
| DCSR(dma) = dcsr & ~DCSR_STOPIRQEN; |
| |
| if (dcsr & DCSR_ENDINTR) { |
| writel(BUF_PART_FULL, host->base + MMC_PRTBUF); |
| } else { |
| pr_err("%s: DMA error on channel %d (DCSR=%#x)\n", |
| mmc_hostname(host->mmc), dma, dcsr); |
| host->data->error = -EIO; |
| pxamci_data_done(host, 0); |
| } |
| } |
| |
| static irqreturn_t pxamci_detect_irq(int irq, void *devid) |
| { |
| struct pxamci_host *host = mmc_priv(devid); |
| |
| mmc_detect_change(devid, msecs_to_jiffies(host->pdata->detect_delay_ms)); |
| return IRQ_HANDLED; |
| } |
| |
| #ifdef CONFIG_OF |
| static const struct of_device_id pxa_mmc_dt_ids[] = { |
| { .compatible = "marvell,pxa-mmc" }, |
| { } |
| }; |
| |
| MODULE_DEVICE_TABLE(of, pxa_mmc_dt_ids); |
| |
| static int pxamci_of_init(struct platform_device *pdev) |
| { |
| struct device_node *np = pdev->dev.of_node; |
| struct pxamci_platform_data *pdata; |
| u32 tmp; |
| |
| if (!np) |
| return 0; |
| |
| pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL); |
| if (!pdata) |
| return -ENOMEM; |
| |
| pdata->gpio_card_detect = |
| of_get_named_gpio(np, "cd-gpios", 0); |
| pdata->gpio_card_ro = |
| of_get_named_gpio(np, "wp-gpios", 0); |
| |
| /* pxa-mmc specific */ |
| pdata->gpio_power = |
| of_get_named_gpio(np, "pxa-mmc,gpio-power", 0); |
| |
| if (of_property_read_u32(np, "pxa-mmc,detect-delay-ms", &tmp) == 0) |
| pdata->detect_delay_ms = tmp; |
| |
| pdev->dev.platform_data = pdata; |
| |
| return 0; |
| } |
| #else |
| static int pxamci_of_init(struct platform_device *pdev) |
| { |
| return 0; |
| } |
| #endif |
| |
| static int pxamci_probe(struct platform_device *pdev) |
| { |
| struct mmc_host *mmc; |
| struct pxamci_host *host = NULL; |
| struct resource *r, *dmarx, *dmatx; |
| int ret, irq, gpio_cd = -1, gpio_ro = -1, gpio_power = -1; |
| |
| ret = pxamci_of_init(pdev); |
| if (ret) |
| return ret; |
| |
| r = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| irq = platform_get_irq(pdev, 0); |
| if (!r || irq < 0) |
| return -ENXIO; |
| |
| r = request_mem_region(r->start, SZ_4K, DRIVER_NAME); |
| if (!r) |
| return -EBUSY; |
| |
| mmc = mmc_alloc_host(sizeof(struct pxamci_host), &pdev->dev); |
| if (!mmc) { |
| ret = -ENOMEM; |
| goto out; |
| } |
| |
| mmc->ops = &pxamci_ops; |
| |
| /* |
| * We can do SG-DMA, but we don't because we never know how much |
| * data we successfully wrote to the card. |
| */ |
| mmc->max_segs = NR_SG; |
| |
| /* |
| * Our hardware DMA can handle a maximum of one page per SG entry. |
| */ |
| mmc->max_seg_size = PAGE_SIZE; |
| |
| /* |
| * Block length register is only 10 bits before PXA27x. |
| */ |
| mmc->max_blk_size = cpu_is_pxa25x() ? 1023 : 2048; |
| |
| /* |
| * Block count register is 16 bits. |
| */ |
| mmc->max_blk_count = 65535; |
| |
| host = mmc_priv(mmc); |
| host->mmc = mmc; |
| host->dma = -1; |
| host->pdata = pdev->dev.platform_data; |
| host->clkrt = CLKRT_OFF; |
| |
| host->clk = clk_get(&pdev->dev, NULL); |
| if (IS_ERR(host->clk)) { |
| ret = PTR_ERR(host->clk); |
| host->clk = NULL; |
| goto out; |
| } |
| |
| host->clkrate = clk_get_rate(host->clk); |
| |
| /* |
| * Calculate minimum clock rate, rounding up. |
| */ |
| mmc->f_min = (host->clkrate + 63) / 64; |
| mmc->f_max = (mmc_has_26MHz()) ? 26000000 : host->clkrate; |
| |
| pxamci_init_ocr(host); |
| |
| mmc->caps = 0; |
| host->cmdat = 0; |
| if (!cpu_is_pxa25x()) { |
| mmc->caps |= MMC_CAP_4_BIT_DATA | MMC_CAP_SDIO_IRQ; |
| host->cmdat |= CMDAT_SDIO_INT_EN; |
| if (mmc_has_26MHz()) |
| mmc->caps |= MMC_CAP_MMC_HIGHSPEED | |
| MMC_CAP_SD_HIGHSPEED; |
| } |
| |
| host->sg_cpu = dma_alloc_coherent(&pdev->dev, PAGE_SIZE, &host->sg_dma, GFP_KERNEL); |
| if (!host->sg_cpu) { |
| ret = -ENOMEM; |
| goto out; |
| } |
| |
| spin_lock_init(&host->lock); |
| host->res = r; |
| host->irq = irq; |
| host->imask = MMC_I_MASK_ALL; |
| |
| host->base = ioremap(r->start, SZ_4K); |
| if (!host->base) { |
| ret = -ENOMEM; |
| goto out; |
| } |
| |
| /* |
| * Ensure that the host controller is shut down, and setup |
| * with our defaults. |
| */ |
| pxamci_stop_clock(host); |
| writel(0, host->base + MMC_SPI); |
| writel(64, host->base + MMC_RESTO); |
| writel(host->imask, host->base + MMC_I_MASK); |
| |
| host->dma = pxa_request_dma(DRIVER_NAME, DMA_PRIO_LOW, |
| pxamci_dma_irq, host); |
| if (host->dma < 0) { |
| ret = -EBUSY; |
| goto out; |
| } |
| |
| ret = request_irq(host->irq, pxamci_irq, 0, DRIVER_NAME, host); |
| if (ret) |
| goto out; |
| |
| platform_set_drvdata(pdev, mmc); |
| |
| dmarx = platform_get_resource(pdev, IORESOURCE_DMA, 0); |
| if (!dmarx) { |
| ret = -ENXIO; |
| goto out; |
| } |
| host->dma_drcmrrx = dmarx->start; |
| |
| dmatx = platform_get_resource(pdev, IORESOURCE_DMA, 1); |
| if (!dmatx) { |
| ret = -ENXIO; |
| goto out; |
| } |
| host->dma_drcmrtx = dmatx->start; |
| |
| if (host->pdata) { |
| gpio_cd = host->pdata->gpio_card_detect; |
| gpio_ro = host->pdata->gpio_card_ro; |
| gpio_power = host->pdata->gpio_power; |
| } |
| if (gpio_is_valid(gpio_power)) { |
| ret = gpio_request(gpio_power, "mmc card power"); |
| if (ret) { |
| dev_err(&pdev->dev, "Failed requesting gpio_power %d\n", gpio_power); |
| goto out; |
| } |
| gpio_direction_output(gpio_power, |
| host->pdata->gpio_power_invert); |
| } |
| if (gpio_is_valid(gpio_ro)) { |
| ret = gpio_request(gpio_ro, "mmc card read only"); |
| if (ret) { |
| dev_err(&pdev->dev, "Failed requesting gpio_ro %d\n", gpio_ro); |
| goto err_gpio_ro; |
| } |
| gpio_direction_input(gpio_ro); |
| } |
| if (gpio_is_valid(gpio_cd)) { |
| ret = gpio_request(gpio_cd, "mmc card detect"); |
| if (ret) { |
| dev_err(&pdev->dev, "Failed requesting gpio_cd %d\n", gpio_cd); |
| goto err_gpio_cd; |
| } |
| gpio_direction_input(gpio_cd); |
| |
| ret = request_irq(gpio_to_irq(gpio_cd), pxamci_detect_irq, |
| IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, |
| "mmc card detect", mmc); |
| if (ret) { |
| dev_err(&pdev->dev, "failed to request card detect IRQ\n"); |
| goto err_request_irq; |
| } |
| } |
| |
| if (host->pdata && host->pdata->init) |
| host->pdata->init(&pdev->dev, pxamci_detect_irq, mmc); |
| |
| if (gpio_is_valid(gpio_power) && host->pdata->setpower) |
| dev_warn(&pdev->dev, "gpio_power and setpower() both defined\n"); |
| if (gpio_is_valid(gpio_ro) && host->pdata->get_ro) |
| dev_warn(&pdev->dev, "gpio_ro and get_ro() both defined\n"); |
| |
| mmc_add_host(mmc); |
| |
| return 0; |
| |
| err_request_irq: |
| gpio_free(gpio_cd); |
| err_gpio_cd: |
| gpio_free(gpio_ro); |
| err_gpio_ro: |
| gpio_free(gpio_power); |
| out: |
| if (host) { |
| if (host->dma >= 0) |
| pxa_free_dma(host->dma); |
| if (host->base) |
| iounmap(host->base); |
| if (host->sg_cpu) |
| dma_free_coherent(&pdev->dev, PAGE_SIZE, host->sg_cpu, host->sg_dma); |
| if (host->clk) |
| clk_put(host->clk); |
| } |
| if (mmc) |
| mmc_free_host(mmc); |
| release_resource(r); |
| return ret; |
| } |
| |
| static int pxamci_remove(struct platform_device *pdev) |
| { |
| struct mmc_host *mmc = platform_get_drvdata(pdev); |
| int gpio_cd = -1, gpio_ro = -1, gpio_power = -1; |
| |
| if (mmc) { |
| struct pxamci_host *host = mmc_priv(mmc); |
| |
| mmc_remove_host(mmc); |
| |
| if (host->pdata) { |
| gpio_cd = host->pdata->gpio_card_detect; |
| gpio_ro = host->pdata->gpio_card_ro; |
| gpio_power = host->pdata->gpio_power; |
| } |
| if (gpio_is_valid(gpio_cd)) { |
| free_irq(gpio_to_irq(gpio_cd), mmc); |
| gpio_free(gpio_cd); |
| } |
| if (gpio_is_valid(gpio_ro)) |
| gpio_free(gpio_ro); |
| if (gpio_is_valid(gpio_power)) |
| gpio_free(gpio_power); |
| if (host->vcc) |
| regulator_put(host->vcc); |
| |
| if (host->pdata && host->pdata->exit) |
| host->pdata->exit(&pdev->dev, mmc); |
| |
| pxamci_stop_clock(host); |
| writel(TXFIFO_WR_REQ|RXFIFO_RD_REQ|CLK_IS_OFF|STOP_CMD| |
| END_CMD_RES|PRG_DONE|DATA_TRAN_DONE, |
| host->base + MMC_I_MASK); |
| |
| DRCMR(host->dma_drcmrrx) = 0; |
| DRCMR(host->dma_drcmrtx) = 0; |
| |
| free_irq(host->irq, host); |
| pxa_free_dma(host->dma); |
| iounmap(host->base); |
| dma_free_coherent(&pdev->dev, PAGE_SIZE, host->sg_cpu, host->sg_dma); |
| |
| clk_put(host->clk); |
| |
| release_resource(host->res); |
| |
| mmc_free_host(mmc); |
| } |
| return 0; |
| } |
| |
| #ifdef CONFIG_PM |
| static int pxamci_suspend(struct device *dev) |
| { |
| struct mmc_host *mmc = dev_get_drvdata(dev); |
| int ret = 0; |
| |
| if (mmc) |
| ret = mmc_suspend_host(mmc); |
| |
| return ret; |
| } |
| |
| static int pxamci_resume(struct device *dev) |
| { |
| struct mmc_host *mmc = dev_get_drvdata(dev); |
| int ret = 0; |
| |
| if (mmc) |
| ret = mmc_resume_host(mmc); |
| |
| return ret; |
| } |
| |
| static const struct dev_pm_ops pxamci_pm_ops = { |
| .suspend = pxamci_suspend, |
| .resume = pxamci_resume, |
| }; |
| #endif |
| |
| static struct platform_driver pxamci_driver = { |
| .probe = pxamci_probe, |
| .remove = pxamci_remove, |
| .driver = { |
| .name = DRIVER_NAME, |
| .owner = THIS_MODULE, |
| .of_match_table = of_match_ptr(pxa_mmc_dt_ids), |
| #ifdef CONFIG_PM |
| .pm = &pxamci_pm_ops, |
| #endif |
| }, |
| }; |
| |
| module_platform_driver(pxamci_driver); |
| |
| MODULE_DESCRIPTION("PXA Multimedia Card Interface Driver"); |
| MODULE_LICENSE("GPL"); |
| MODULE_ALIAS("platform:pxa2xx-mci"); |