drm/i915: Rename many remaining uses of "output" to encoder or connector.
Signed-off-by: Eric Anholt <eric@anholt.net>
diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index 2595c4c..34d2652 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -754,8 +754,8 @@
return false;
}
-struct drm_connector *
-intel_pipe_get_output (struct drm_crtc *crtc)
+static struct drm_connector *
+intel_pipe_get_connector (struct drm_crtc *crtc)
{
struct drm_device *dev = crtc->dev;
struct drm_mode_config *mode_config = &dev->mode_config;
@@ -2916,7 +2916,7 @@
int dspsize_reg = (plane == 0) ? DSPASIZE : DSPBSIZE;
int dsppos_reg = (plane == 0) ? DSPAPOS : DSPBPOS;
int pipesrc_reg = (pipe == 0) ? PIPEASRC : PIPEBSRC;
- int refclk, num_outputs = 0;
+ int refclk, num_connectors = 0;
intel_clock_t clock, reduced_clock;
u32 dpll = 0, fp = 0, fp2 = 0, dspcntr, pipeconf;
bool ok, has_reduced_clock = false, is_sdvo = false, is_dvo = false;
@@ -2974,10 +2974,10 @@
break;
}
- num_outputs++;
+ num_connectors++;
}
- if (is_lvds && dev_priv->lvds_use_ssc && num_outputs < 2) {
+ if (is_lvds && dev_priv->lvds_use_ssc && num_connectors < 2) {
refclk = dev_priv->lvds_ssc_freq * 1000;
DRM_DEBUG_KMS("using SSC reference clock of %d MHz\n",
refclk / 1000);
@@ -3048,7 +3048,7 @@
if (is_edp) {
struct drm_connector *edp;
target_clock = mode->clock;
- edp = intel_pipe_get_output(crtc);
+ edp = intel_pipe_get_connector(crtc);
intel_edp_link_config(to_intel_encoder(edp),
&lane, &link_bw);
} else {
@@ -3230,7 +3230,7 @@
/* XXX: just matching BIOS for now */
/* dpll |= PLL_REF_INPUT_TVCLKINBC; */
dpll |= 3;
- else if (is_lvds && dev_priv->lvds_use_ssc && num_outputs < 2)
+ else if (is_lvds && dev_priv->lvds_use_ssc && num_connectors < 2)
dpll |= PLLB_REF_INPUT_SPREADSPECTRUMIN;
else
dpll |= PLL_REF_INPUT_DREFCLK;
@@ -3654,9 +3654,9 @@
* detection.
*
* It will be up to the load-detect code to adjust the pipe as appropriate for
- * its requirements. The pipe will be connected to no other outputs.
+ * its requirements. The pipe will be connected to no other encoders.
*
- * Currently this code will only succeed if there is a pipe with no outputs
+ * Currently this code will only succeed if there is a pipe with no encoders
* configured for it. In the future, it could choose to temporarily disable
* some outputs to free up a pipe for its use.
*
@@ -3770,7 +3770,7 @@
drm_helper_disable_unused_functions(dev);
}
- /* Switch crtc and output back off if necessary */
+ /* Switch crtc and encoder back off if necessary */
if (crtc->enabled && dpms_mode != DRM_MODE_DPMS_ON) {
if (encoder->crtc == crtc)
encoder_funcs->dpms(encoder, dpms_mode);