Merge branch 'omap-upstream' into for-next
Conflicts:
arch/arm/mach-omap2/Makefile
diff --git a/arch/arm/mach-omap1/clock.c b/arch/arm/mach-omap1/clock.c
index 336e51d..436eed2 100644
--- a/arch/arm/mach-omap1/clock.c
+++ b/arch/arm/mach-omap1/clock.c
@@ -776,7 +776,7 @@
arm_idlect1_mask = ~0;
for (c = omap_clks; c < omap_clks + ARRAY_SIZE(omap_clks); c++)
- clk_init_one(c->lk.clk);
+ clk_preinit(c->lk.clk);
cpu_mask = 0;
if (cpu_is_omap16xx())
diff --git a/arch/arm/mach-omap1/pm.c b/arch/arm/mach-omap1/pm.c
index 9774c1f..5218943 100644
--- a/arch/arm/mach-omap1/pm.c
+++ b/arch/arm/mach-omap1/pm.c
@@ -53,11 +53,12 @@
#include <mach/clock.h>
#include <mach/sram.h>
#include <mach/tc.h>
-#include <mach/pm.h>
#include <mach/mux.h>
#include <mach/dma.h>
#include <mach/dmtimer.h>
+#include "pm.h"
+
static unsigned int arm_sleep_save[ARM_SLEEP_SAVE_SIZE];
static unsigned short dsp_sleep_save[DSP_SLEEP_SAVE_SIZE];
static unsigned short ulpd_sleep_save[ULPD_SLEEP_SAVE_SIZE];
@@ -101,7 +102,7 @@
* going idle we continue to do idle even if we get
* a clock tick interrupt . .
*/
-void omap_pm_idle(void)
+void omap1_pm_idle(void)
{
extern __u32 arm_idlect1_mask;
__u32 use_idlect1 = arm_idlect1_mask;
@@ -222,7 +223,7 @@
#define EN_APICK 6 /* ARM_IDLECT2 */
#define DSP_EN 1 /* ARM_RSTCT1 */
-void omap_pm_suspend(void)
+void omap1_pm_suspend(void)
{
unsigned long arg0 = 0, arg1 = 0;
@@ -610,7 +611,7 @@
{
case PM_SUSPEND_STANDBY:
case PM_SUSPEND_MEM:
- omap_pm_suspend();
+ omap1_pm_suspend();
break;
default:
return -EINVAL;
@@ -683,7 +684,7 @@
return -ENODEV;
}
- pm_idle = omap_pm_idle;
+ pm_idle = omap1_pm_idle;
if (cpu_is_omap730())
setup_irq(INT_730_WAKE_UP_REQ, &omap_wakeup_irq);
diff --git a/arch/arm/plat-omap/include/mach/pm.h b/arch/arm/mach-omap1/pm.h
similarity index 76%
rename from arch/arm/plat-omap/include/mach/pm.h
rename to arch/arm/mach-omap1/pm.h
index ce6ee79..9ed5e2c 100644
--- a/arch/arm/plat-omap/include/mach/pm.h
+++ b/arch/arm/mach-omap1/pm.h
@@ -1,7 +1,7 @@
/*
- * arch/arm/plat-omap/include/mach/pm.h
+ * arch/arm/mach-omap1/pm.h
*
- * Header file for OMAP Power Management Routines
+ * Header file for OMAP1 Power Management Routines
*
* Author: MontaVista Software, Inc.
* support@mvista.com
@@ -31,8 +31,8 @@
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
-#ifndef __ASM_ARCH_OMAP_PM_H
-#define __ASM_ARCH_OMAP_PM_H
+#ifndef __ARCH_ARM_MACH_OMAP1_PM_H
+#define __ARCH_ARM_MACH_OMAP1_PM_H
/*
* ----------------------------------------------------------------------------
@@ -106,8 +106,7 @@
#if !defined(CONFIG_ARCH_OMAP730) && \
!defined(CONFIG_ARCH_OMAP15XX) && \
- !defined(CONFIG_ARCH_OMAP16XX) && \
- !defined(CONFIG_ARCH_OMAP24XX)
+ !defined(CONFIG_ARCH_OMAP16XX)
#warning "Power management for this processor not implemented yet"
#endif
@@ -115,29 +114,27 @@
#include <linux/clk.h>
+extern struct kset power_subsys;
+
extern void prevent_idle_sleep(void);
extern void allow_idle_sleep(void);
-extern void omap_pm_idle(void);
-extern void omap_pm_suspend(void);
+extern void omap1_pm_idle(void);
+extern void omap1_pm_suspend(void);
+
extern void omap730_cpu_suspend(unsigned short, unsigned short);
extern void omap1510_cpu_suspend(unsigned short, unsigned short);
extern void omap1610_cpu_suspend(unsigned short, unsigned short);
-extern void omap24xx_cpu_suspend(u32 dll_ctrl, void __iomem *sdrc_dlla_ctrl,
- void __iomem *sdrc_power);
extern void omap730_idle_loop_suspend(void);
extern void omap1510_idle_loop_suspend(void);
extern void omap1610_idle_loop_suspend(void);
-extern void omap24xx_idle_loop_suspend(void);
extern unsigned int omap730_cpu_suspend_sz;
extern unsigned int omap1510_cpu_suspend_sz;
extern unsigned int omap1610_cpu_suspend_sz;
-extern unsigned int omap24xx_cpu_suspend_sz;
extern unsigned int omap730_idle_loop_suspend_sz;
extern unsigned int omap1510_idle_loop_suspend_sz;
extern unsigned int omap1610_idle_loop_suspend_sz;
-extern unsigned int omap24xx_idle_loop_suspend_sz;
#ifdef CONFIG_OMAP_SERIAL_WAKE
extern void omap_serial_wake_trigger(int enable);
@@ -170,10 +167,6 @@
#define MPUI1610_RESTORE(x) omap_writel((mpui1610_sleep_save[MPUI1610_SLEEP_SAVE_##x]), (x))
#define MPUI1610_SHOW(x) mpui1610_sleep_save[MPUI1610_SLEEP_SAVE_##x]
-#define OMAP24XX_SAVE(x) omap24xx_sleep_save[OMAP24XX_SLEEP_SAVE_##x] = x
-#define OMAP24XX_RESTORE(x) x = omap24xx_sleep_save[OMAP24XX_SLEEP_SAVE_##x]
-#define OMAP24XX_SHOW(x) omap24xx_sleep_save[OMAP24XX_SLEEP_SAVE_##x]
-
/*
* List of global OMAP registers to preserve.
* More ones like CP and general purpose register values are preserved
@@ -283,63 +276,5 @@
#endif
};
-enum omap24xx_save_state {
- OMAP24XX_SLEEP_SAVE_START = 0,
- OMAP24XX_SLEEP_SAVE_INTC_MIR0,
- OMAP24XX_SLEEP_SAVE_INTC_MIR1,
- OMAP24XX_SLEEP_SAVE_INTC_MIR2,
-
- OMAP24XX_SLEEP_SAVE_CM_CLKSTCTRL_MPU,
- OMAP24XX_SLEEP_SAVE_CM_CLKSTCTRL_CORE,
- OMAP24XX_SLEEP_SAVE_CM_CLKSTCTRL_GFX,
- OMAP24XX_SLEEP_SAVE_CM_CLKSTCTRL_DSP,
- OMAP24XX_SLEEP_SAVE_CM_CLKSTCTRL_MDM,
-
- OMAP24XX_SLEEP_SAVE_PM_PWSTCTRL_MPU,
- OMAP24XX_SLEEP_SAVE_PM_PWSTCTRL_CORE,
- OMAP24XX_SLEEP_SAVE_PM_PWSTCTRL_GFX,
- OMAP24XX_SLEEP_SAVE_PM_PWSTCTRL_DSP,
- OMAP24XX_SLEEP_SAVE_PM_PWSTCTRL_MDM,
-
- OMAP24XX_SLEEP_SAVE_CM_IDLEST1_CORE,
- OMAP24XX_SLEEP_SAVE_CM_IDLEST2_CORE,
- OMAP24XX_SLEEP_SAVE_CM_IDLEST3_CORE,
- OMAP24XX_SLEEP_SAVE_CM_IDLEST4_CORE,
- OMAP24XX_SLEEP_SAVE_CM_IDLEST_GFX,
- OMAP24XX_SLEEP_SAVE_CM_IDLEST_WKUP,
- OMAP24XX_SLEEP_SAVE_CM_IDLEST_CKGEN,
- OMAP24XX_SLEEP_SAVE_CM_IDLEST_DSP,
- OMAP24XX_SLEEP_SAVE_CM_IDLEST_MDM,
-
- OMAP24XX_SLEEP_SAVE_CM_AUTOIDLE1_CORE,
- OMAP24XX_SLEEP_SAVE_CM_AUTOIDLE2_CORE,
- OMAP24XX_SLEEP_SAVE_CM_AUTOIDLE3_CORE,
- OMAP24XX_SLEEP_SAVE_CM_AUTOIDLE4_CORE,
- OMAP24XX_SLEEP_SAVE_CM_AUTOIDLE_WKUP,
- OMAP24XX_SLEEP_SAVE_CM_AUTOIDLE_PLL,
- OMAP24XX_SLEEP_SAVE_CM_AUTOIDLE_DSP,
- OMAP24XX_SLEEP_SAVE_CM_AUTOIDLE_MDM,
-
- OMAP24XX_SLEEP_SAVE_CM_FCLKEN1_CORE,
- OMAP24XX_SLEEP_SAVE_CM_FCLKEN2_CORE,
- OMAP24XX_SLEEP_SAVE_CM_ICLKEN1_CORE,
- OMAP24XX_SLEEP_SAVE_CM_ICLKEN2_CORE,
- OMAP24XX_SLEEP_SAVE_CM_ICLKEN3_CORE,
- OMAP24XX_SLEEP_SAVE_CM_ICLKEN4_CORE,
- OMAP24XX_SLEEP_SAVE_GPIO1_IRQENABLE1,
- OMAP24XX_SLEEP_SAVE_GPIO2_IRQENABLE1,
- OMAP24XX_SLEEP_SAVE_GPIO3_IRQENABLE1,
- OMAP24XX_SLEEP_SAVE_GPIO4_IRQENABLE1,
- OMAP24XX_SLEEP_SAVE_GPIO3_OE,
- OMAP24XX_SLEEP_SAVE_GPIO4_OE,
- OMAP24XX_SLEEP_SAVE_GPIO3_RISINGDETECT,
- OMAP24XX_SLEEP_SAVE_GPIO3_FALLINGDETECT,
- OMAP24XX_SLEEP_SAVE_CONTROL_PADCONF_SPI1_NCS2,
- OMAP24XX_SLEEP_SAVE_CONTROL_PADCONF_MCBSP1_DX,
- OMAP24XX_SLEEP_SAVE_CONTROL_PADCONF_SSI1_FLAG_TX,
- OMAP24XX_SLEEP_SAVE_CONTROL_PADCONF_SYS_NIRQW0,
- OMAP24XX_SLEEP_SAVE_SIZE
-};
-
#endif /* ASSEMBLER */
#endif /* __ASM_ARCH_OMAP_PM_H */
diff --git a/arch/arm/mach-omap1/serial.c b/arch/arm/mach-omap1/serial.c
index 842090b..f754cee 100644
--- a/arch/arm/mach-omap1/serial.c
+++ b/arch/arm/mach-omap1/serial.c
@@ -26,9 +26,6 @@
#include <mach/mux.h>
#include <mach/gpio.h>
#include <mach/fpga.h>
-#ifdef CONFIG_PM
-#include <mach/pm.h>
-#endif
static struct clk * uart1_ck;
static struct clk * uart2_ck;
diff --git a/arch/arm/mach-omap1/sleep.S b/arch/arm/mach-omap1/sleep.S
index f3eac93..22e8568 100644
--- a/arch/arm/mach-omap1/sleep.S
+++ b/arch/arm/mach-omap1/sleep.S
@@ -35,7 +35,7 @@
#include <linux/linkage.h>
#include <asm/assembler.h>
#include <mach/io.h>
-#include <mach/pm.h>
+#include "pm.h"
.text
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index e4f6f61..516477e 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -25,8 +25,10 @@
# Power Management
ifeq ($(CONFIG_PM),y)
-obj-y += pm.o
+obj-$(CONFIG_ARCH_OMAP2) += pm24xx.o
obj-$(CONFIG_ARCH_OMAP24XX) += sleep24xx.o
+obj-$(CONFIG_ARCH_OMAP3) += pm34xx.o sleep34xx.o
+obj-$(CONFIG_PM_DEBUG) += pm-debug.o
endif
# Clock framework
@@ -55,9 +57,7 @@
mmc-twl4030.o
# Platform specific device init code
-ifeq ($(CONFIG_USB_MUSB_SOC),y)
obj-y += usb-musb.o
-endif
onenand-$(CONFIG_MTD_ONENAND_OMAP2) := gpmc-onenand.o
obj-y += $(onenand-m) $(onenand-y)
diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c
index dd37483..ba528f8 100644
--- a/arch/arm/mach-omap2/clock.c
+++ b/arch/arm/mach-omap2/clock.c
@@ -547,8 +547,8 @@
const struct clksel_rate *clkr;
u32 last_div = 0;
- printk(KERN_INFO "clock: clksel_round_rate_div: %s target_rate %ld\n",
- clk->name, target_rate);
+ pr_debug("clock: clksel_round_rate_div: %s target_rate %ld\n",
+ clk->name, target_rate);
*new_div = 1;
@@ -562,7 +562,7 @@
/* Sanity check */
if (clkr->div <= last_div)
- printk(KERN_ERR "clock: clksel_rate table not sorted "
+ pr_err("clock: clksel_rate table not sorted "
"for clock %s", clk->name);
last_div = clkr->div;
@@ -574,7 +574,7 @@
}
if (!clkr->div) {
- printk(KERN_ERR "clock: Could not find divisor for target "
+ pr_err("clock: Could not find divisor for target "
"rate %ld for clock %s parent %s\n", target_rate,
clk->name, clk->parent->name);
return ~0;
@@ -582,8 +582,8 @@
*new_div = clkr->div;
- printk(KERN_INFO "clock: new_div = %d, new_rate = %ld\n", *new_div,
- (clk->parent->rate / clkr->div));
+ pr_debug("clock: new_div = %d, new_rate = %ld\n", *new_div,
+ (clk->parent->rate / clkr->div));
return (clk->parent->rate / clkr->div);
}
@@ -1035,7 +1035,7 @@
if ((regval32 & (1 << clk->enable_bit)) == v)
return;
- printk(KERN_INFO "Disabling unused clock \"%s\"\n", clk->name);
+ printk(KERN_DEBUG "Disabling unused clock \"%s\"\n", clk->name);
if (cpu_is_omap34xx()) {
omap2_clk_enable(clk);
omap2_clk_disable(clk);
diff --git a/arch/arm/mach-omap2/clock24xx.c b/arch/arm/mach-omap2/clock24xx.c
index c442fe9..44de027 100644
--- a/arch/arm/mach-omap2/clock24xx.c
+++ b/arch/arm/mach-omap2/clock24xx.c
@@ -725,7 +725,7 @@
clk_init(&omap2_clk_functions);
for (c = omap24xx_clks; c < omap24xx_clks + ARRAY_SIZE(omap24xx_clks); c++)
- clk_init_one(c->lk.clk);
+ clk_preinit(c->lk.clk);
osc_ck.rate = omap2_osc_clk_recalc(&osc_ck);
propagate_rate(&osc_ck);
diff --git a/arch/arm/mach-omap2/clock34xx.c b/arch/arm/mach-omap2/clock34xx.c
index ba05aa4..9e43fe5 100644
--- a/arch/arm/mach-omap2/clock34xx.c
+++ b/arch/arm/mach-omap2/clock34xx.c
@@ -129,6 +129,9 @@
CLK(NULL, "sgx_fck", &sgx_fck, CK_3430ES2),
CLK(NULL, "sgx_ick", &sgx_ick, CK_3430ES2),
CLK(NULL, "d2d_26m_fck", &d2d_26m_fck, CK_3430ES1),
+ CLK(NULL, "modem_fck", &modem_fck, CK_343X),
+ CLK(NULL, "sad2d_ick", &sad2d_ick, CK_343X),
+ CLK(NULL, "mad2d_ick", &mad2d_ick, CK_343X),
CLK(NULL, "gpt10_fck", &gpt10_fck, CK_343X),
CLK(NULL, "gpt11_fck", &gpt11_fck, CK_343X),
CLK(NULL, "cpefuse_fck", &cpefuse_fck, CK_3430ES2),
@@ -281,6 +284,8 @@
#define MAX_DPLL_WAIT_TRIES 1000000
+#define MIN_SDRC_DLL_LOCK_FREQ 83000000
+
/**
* omap3_dpll_recalc - recalculate DPLL rate
* @clk: DPLL struct clk
@@ -703,6 +708,7 @@
static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate)
{
u32 new_div = 0;
+ u32 unlock_dll = 0;
unsigned long validrate, sdrcrate;
struct omap_sdrc_params *sp;
@@ -729,17 +735,22 @@
if (!sp)
return -EINVAL;
- pr_info("clock: changing CORE DPLL rate from %lu to %lu\n", clk->rate,
- validrate);
- pr_info("clock: SDRC timing params used: %08x %08x %08x\n",
- sp->rfr_ctrl, sp->actim_ctrla, sp->actim_ctrlb);
+ if (sdrcrate < MIN_SDRC_DLL_LOCK_FREQ) {
+ pr_debug("clock: will unlock SDRC DLL\n");
+ unlock_dll = 1;
+ }
+
+ pr_debug("clock: changing CORE DPLL rate from %lu to %lu\n", clk->rate,
+ validrate);
+ pr_debug("clock: SDRC timing params used: %08x %08x %08x\n",
+ sp->rfr_ctrl, sp->actim_ctrla, sp->actim_ctrlb);
/* REVISIT: SRAM code doesn't support other M2 divisors yet */
WARN_ON(new_div != 1 && new_div != 2);
/* REVISIT: Add SDRC_MR changing to this code also */
omap3_configure_core_dpll(sp->rfr_ctrl, sp->actim_ctrla,
- sp->actim_ctrlb, new_div);
+ sp->actim_ctrlb, new_div, unlock_dll);
return 0;
}
@@ -956,7 +967,7 @@
clk_init(&omap2_clk_functions);
for (c = omap34xx_clks; c < omap34xx_clks + ARRAY_SIZE(omap34xx_clks); c++)
- clk_init_one(c->lk.clk);
+ clk_preinit(c->lk.clk);
for (c = omap34xx_clks; c < omap34xx_clks + ARRAY_SIZE(omap34xx_clks); c++)
if (c->cpu & cpu_clkflg) {
diff --git a/arch/arm/mach-omap2/clock34xx.h b/arch/arm/mach-omap2/clock34xx.h
index 496f0e9..e433aec 100644
--- a/arch/arm/mach-omap2/clock34xx.h
+++ b/arch/arm/mach-omap2/clock34xx.h
@@ -1230,6 +1230,37 @@
.recalc = &followparent_recalc,
};
+static struct clk modem_fck = {
+ .name = "modem_fck",
+ .ops = &clkops_omap2_dflt_wait,
+ .parent = &sys_ck,
+ .init = &omap2_init_clk_clkdm,
+ .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1),
+ .enable_bit = OMAP3430_EN_MODEM_SHIFT,
+ .clkdm_name = "d2d_clkdm",
+ .recalc = &followparent_recalc,
+};
+
+static struct clk sad2d_ick = {
+ .name = "sad2d_ick",
+ .ops = &clkops_omap2_dflt_wait,
+ .parent = &l3_ick,
+ .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1),
+ .enable_bit = OMAP3430_EN_SAD2D_SHIFT,
+ .clkdm_name = "d2d_clkdm",
+ .recalc = &followparent_recalc,
+};
+
+static struct clk mad2d_ick = {
+ .name = "mad2d_ick",
+ .ops = &clkops_omap2_dflt_wait,
+ .parent = &l3_ick,
+ .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN3),
+ .enable_bit = OMAP3430_EN_MAD2D_SHIFT,
+ .clkdm_name = "d2d_clkdm",
+ .recalc = &followparent_recalc,
+};
+
static const struct clksel omap343x_gpt_clksel[] = {
{ .parent = &omap_32k_fck, .rates = gpt_32k_rates },
{ .parent = &sys_ck, .rates = gpt_sys_rates },
@@ -1947,8 +1978,6 @@
.recalc = &omap2_clksel_recalc,
};
-/* XXX MDM_INTC_ICK, SAD2D_ICK ?? */
-
/* SECURITY_L4_ICK2 based clocks */
static struct clk security_l4_ick2 = {
diff --git a/arch/arm/mach-omap2/clockdomains.h b/arch/arm/mach-omap2/clockdomains.h
index 281d5da..fe319ae 100644
--- a/arch/arm/mach-omap2/clockdomains.h
+++ b/arch/arm/mach-omap2/clockdomains.h
@@ -195,7 +195,7 @@
static struct clockdomain d2d_clkdm = {
.name = "d2d_clkdm",
.pwrdm = { .name = "core_pwrdm" },
- .flags = CLKDM_CAN_HWSUP,
+ .flags = CLKDM_CAN_HWSUP_SWSUP,
.clktrctrl_mask = OMAP3430ES1_CLKTRCTRL_D2D_MASK,
.omap_chip = OMAP_CHIP_INIT(CHIP_IS_OMAP3430),
};
diff --git a/arch/arm/mach-omap2/cm-regbits-34xx.h b/arch/arm/mach-omap2/cm-regbits-34xx.h
index 6f3f5a3..6923deb 100644
--- a/arch/arm/mach-omap2/cm-regbits-34xx.h
+++ b/arch/arm/mach-omap2/cm-regbits-34xx.h
@@ -145,6 +145,8 @@
#define OMAP3430_CLKACTIVITY_MPU_MASK (1 << 0)
/* CM_FCLKEN1_CORE specific bits */
+#define OMAP3430_EN_MODEM (1 << 31)
+#define OMAP3430_EN_MODEM_SHIFT 31
/* CM_ICLKEN1_CORE specific bits */
#define OMAP3430_EN_ICR (1 << 29)
@@ -161,6 +163,8 @@
#define OMAP3430_EN_MAILBOXES_SHIFT 7
#define OMAP3430_EN_OMAPCTRL (1 << 6)
#define OMAP3430_EN_OMAPCTRL_SHIFT 6
+#define OMAP3430_EN_SAD2D (1 << 3)
+#define OMAP3430_EN_SAD2D_SHIFT 3
#define OMAP3430_EN_SDRC (1 << 1)
#define OMAP3430_EN_SDRC_SHIFT 1
@@ -176,6 +180,10 @@
#define OMAP3430_EN_DES1 (1 << 0)
#define OMAP3430_EN_DES1_SHIFT 0
+/* CM_ICLKEN3_CORE */
+#define OMAP3430_EN_MAD2D_SHIFT 3
+#define OMAP3430_EN_MAD2D (1 << 3)
+
/* CM_FCLKEN3_CORE specific bits */
#define OMAP3430ES2_EN_TS_SHIFT 1
#define OMAP3430ES2_EN_TS_MASK (1 << 1)
@@ -231,6 +239,8 @@
#define OMAP3430ES2_ST_CPEFUSE_MASK (1 << 0)
/* CM_AUTOIDLE1_CORE */
+#define OMAP3430_AUTO_MODEM (1 << 31)
+#define OMAP3430_AUTO_MODEM_SHIFT 31
#define OMAP3430ES2_AUTO_MMC3 (1 << 30)
#define OMAP3430ES2_AUTO_MMC3_SHIFT 30
#define OMAP3430ES2_AUTO_ICR (1 << 29)
@@ -287,6 +297,8 @@
#define OMAP3430_AUTO_HSOTGUSB_SHIFT 4
#define OMAP3430ES1_AUTO_D2D (1 << 3)
#define OMAP3430ES1_AUTO_D2D_SHIFT 3
+#define OMAP3430_AUTO_SAD2D (1 << 3)
+#define OMAP3430_AUTO_SAD2D_SHIFT 3
#define OMAP3430_AUTO_SSI (1 << 0)
#define OMAP3430_AUTO_SSI_SHIFT 0
@@ -308,6 +320,8 @@
#define OMAP3430ES2_AUTO_USBTLL (1 << 2)
#define OMAP3430ES2_AUTO_USBTLL_SHIFT 2
#define OMAP3430ES2_AUTO_USBTLL_MASK (1 << 2)
+#define OMAP3430_AUTO_MAD2D_SHIFT 3
+#define OMAP3430_AUTO_MAD2D (1 << 3)
/* CM_CLKSEL_CORE */
#define OMAP3430_CLKSEL_SSI_SHIFT 8
diff --git a/arch/arm/mach-omap2/irq.c b/arch/arm/mach-omap2/irq.c
index 998c5c4..b828638 100644
--- a/arch/arm/mach-omap2/irq.c
+++ b/arch/arm/mach-omap2/irq.c
@@ -28,7 +28,6 @@
#define INTC_MIR_CLEAR0 0x0088
#define INTC_MIR_SET0 0x008c
#define INTC_PENDING_IRQ0 0x0098
-
/* Number of IRQ state bits in each MIR register */
#define IRQ_BITS_PER_REG 32
@@ -134,7 +133,6 @@
.ack = omap_mask_ack_irq,
.mask = omap_mask_irq,
.unmask = omap_unmask_irq,
- .disable = omap_mask_irq,
};
static void __init omap_irq_bank_init_one(struct omap_irq_bank *bank)
@@ -157,6 +155,22 @@
intc_bank_write_reg(1 << 0, bank, INTC_SYSCONFIG);
}
+int omap_irq_pending(void)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(irq_banks); i++) {
+ struct omap_irq_bank *bank = irq_banks + i;
+ int irq;
+
+ for (irq = 0; irq < bank->nr_irqs; irq += 32)
+ if (intc_bank_read_reg(bank, INTC_PENDING_IRQ0 +
+ ((irq >> 5) << 5)))
+ return 1;
+ }
+ return 0;
+}
+
void __init omap_init_irq(void)
{
unsigned long nr_of_irqs = 0;
diff --git a/arch/arm/mach-omap2/pm-debug.c b/arch/arm/mach-omap2/pm-debug.c
new file mode 100644
index 0000000..6cc375a
--- /dev/null
+++ b/arch/arm/mach-omap2/pm-debug.c
@@ -0,0 +1,152 @@
+/*
+ * OMAP Power Management debug routines
+ *
+ * Copyright (C) 2005 Texas Instruments, Inc.
+ * Copyright (C) 2006-2008 Nokia Corporation
+ *
+ * Written by:
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Tony Lindgren
+ * Juha Yrjola
+ * Amit Kucheria <amit.kucheria@nokia.com>
+ * Igor Stoppa <igor.stoppa@nokia.com>
+ * Jouni Hogander
+ *
+ * Based on pm.c for omap2
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/timer.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/io.h>
+
+#include <mach/clock.h>
+#include <mach/board.h>
+
+#include "prm.h"
+#include "cm.h"
+#include "pm.h"
+
+int omap2_pm_debug;
+
+#define DUMP_PRM_MOD_REG(mod, reg) \
+ regs[reg_count].name = #mod "." #reg; \
+ regs[reg_count++].val = prm_read_mod_reg(mod, reg)
+#define DUMP_CM_MOD_REG(mod, reg) \
+ regs[reg_count].name = #mod "." #reg; \
+ regs[reg_count++].val = cm_read_mod_reg(mod, reg)
+#define DUMP_PRM_REG(reg) \
+ regs[reg_count].name = #reg; \
+ regs[reg_count++].val = __raw_readl(reg)
+#define DUMP_CM_REG(reg) \
+ regs[reg_count].name = #reg; \
+ regs[reg_count++].val = __raw_readl(reg)
+#define DUMP_INTC_REG(reg, off) \
+ regs[reg_count].name = #reg; \
+ regs[reg_count++].val = __raw_readl(IO_ADDRESS(0x480fe000 + (off)))
+
+void omap2_pm_dump(int mode, int resume, unsigned int us)
+{
+ struct reg {
+ const char *name;
+ u32 val;
+ } regs[32];
+ int reg_count = 0, i;
+ const char *s1 = NULL, *s2 = NULL;
+
+ if (!resume) {
+#if 0
+ /* MPU */
+ DUMP_PRM_MOD_REG(OCP_MOD, OMAP2_PRM_IRQENABLE_MPU_OFFSET);
+ DUMP_CM_MOD_REG(MPU_MOD, CM_CLKSTCTRL);
+ DUMP_PRM_MOD_REG(MPU_MOD, PM_PWSTCTRL);
+ DUMP_PRM_MOD_REG(MPU_MOD, PM_PWSTST);
+ DUMP_PRM_MOD_REG(MPU_MOD, PM_WKDEP);
+#endif
+#if 0
+ /* INTC */
+ DUMP_INTC_REG(INTC_MIR0, 0x0084);
+ DUMP_INTC_REG(INTC_MIR1, 0x00a4);
+ DUMP_INTC_REG(INTC_MIR2, 0x00c4);
+#endif
+#if 0
+ DUMP_CM_MOD_REG(CORE_MOD, CM_FCLKEN1);
+ if (cpu_is_omap24xx()) {
+ DUMP_CM_MOD_REG(CORE_MOD, OMAP24XX_CM_FCLKEN2);
+ DUMP_PRM_MOD_REG(OMAP24XX_GR_MOD,
+ OMAP2_PRCM_CLKEMUL_CTRL_OFFSET);
+ DUMP_PRM_MOD_REG(OMAP24XX_GR_MOD,
+ OMAP2_PRCM_CLKSRC_CTRL_OFFSET);
+ }
+ DUMP_CM_MOD_REG(WKUP_MOD, CM_FCLKEN);
+ DUMP_CM_MOD_REG(CORE_MOD, CM_ICLKEN1);
+ DUMP_CM_MOD_REG(CORE_MOD, CM_ICLKEN2);
+ DUMP_CM_MOD_REG(WKUP_MOD, CM_ICLKEN);
+ DUMP_CM_MOD_REG(PLL_MOD, CM_CLKEN);
+ DUMP_CM_MOD_REG(PLL_MOD, CM_AUTOIDLE);
+ DUMP_PRM_MOD_REG(CORE_MOD, PM_PWSTST);
+#endif
+#if 0
+ /* DSP */
+ if (cpu_is_omap24xx()) {
+ DUMP_CM_MOD_REG(OMAP24XX_DSP_MOD, CM_FCLKEN);
+ DUMP_CM_MOD_REG(OMAP24XX_DSP_MOD, CM_ICLKEN);
+ DUMP_CM_MOD_REG(OMAP24XX_DSP_MOD, CM_IDLEST);
+ DUMP_CM_MOD_REG(OMAP24XX_DSP_MOD, CM_AUTOIDLE);
+ DUMP_CM_MOD_REG(OMAP24XX_DSP_MOD, CM_CLKSEL);
+ DUMP_CM_MOD_REG(OMAP24XX_DSP_MOD, CM_CLKSTCTRL);
+ DUMP_PRM_MOD_REG(OMAP24XX_DSP_MOD, RM_RSTCTRL);
+ DUMP_PRM_MOD_REG(OMAP24XX_DSP_MOD, RM_RSTST);
+ DUMP_PRM_MOD_REG(OMAP24XX_DSP_MOD, PM_PWSTCTRL);
+ DUMP_PRM_MOD_REG(OMAP24XX_DSP_MOD, PM_PWSTST);
+ }
+#endif
+ } else {
+ DUMP_PRM_MOD_REG(CORE_MOD, PM_WKST1);
+ if (cpu_is_omap24xx())
+ DUMP_PRM_MOD_REG(CORE_MOD, OMAP24XX_PM_WKST2);
+ DUMP_PRM_MOD_REG(WKUP_MOD, PM_WKST);
+ DUMP_PRM_MOD_REG(OCP_MOD, OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
+#if 1
+ DUMP_INTC_REG(INTC_PENDING_IRQ0, 0x0098);
+ DUMP_INTC_REG(INTC_PENDING_IRQ1, 0x00b8);
+ DUMP_INTC_REG(INTC_PENDING_IRQ2, 0x00d8);
+#endif
+ }
+
+ switch (mode) {
+ case 0:
+ s1 = "full";
+ s2 = "retention";
+ break;
+ case 1:
+ s1 = "MPU";
+ s2 = "retention";
+ break;
+ case 2:
+ s1 = "MPU";
+ s2 = "idle";
+ break;
+ }
+
+ if (!resume)
+#ifdef CONFIG_NO_HZ
+ printk(KERN_INFO
+ "--- Going to %s %s (next timer after %u ms)\n", s1, s2,
+ jiffies_to_msecs(get_next_timer_interrupt(jiffies) -
+ jiffies));
+#else
+ printk(KERN_INFO "--- Going to %s %s\n", s1, s2);
+#endif
+ else
+ printk(KERN_INFO "--- Woke up (slept for %u.%03u ms)\n",
+ us / 1000, us % 1000);
+
+ for (i = 0; i < reg_count; i++)
+ printk(KERN_INFO "%-20s: 0x%08x\n", regs[i].name, regs[i].val);
+}
diff --git a/arch/arm/mach-omap2/pm.c b/arch/arm/mach-omap2/pm.c
deleted file mode 100644
index ea8ceae..0000000
--- a/arch/arm/mach-omap2/pm.c
+++ /dev/null
@@ -1,111 +0,0 @@
-/*
- * linux/arch/arm/mach-omap2/pm.c
- *
- * OMAP2 Power Management Routines
- *
- * Copyright (C) 2006 Nokia Corporation
- * Tony Lindgren <tony@atomide.com>
- *
- * Copyright (C) 2005 Texas Instruments, Inc.
- * Richard Woodruff <r-woodruff2@ti.com>
- *
- * Based on pm.c for omap1
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/suspend.h>
-#include <linux/sched.h>
-#include <linux/proc_fs.h>
-#include <linux/interrupt.h>
-#include <linux/sysfs.h>
-#include <linux/module.h>
-#include <linux/delay.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-
-#include <asm/irq.h>
-#include <asm/atomic.h>
-#include <asm/mach/time.h>
-#include <asm/mach/irq.h>
-
-#include <mach/irqs.h>
-#include <mach/clock.h>
-#include <mach/sram.h>
-#include <mach/pm.h>
-
-static struct clk *vclk;
-static void (*omap2_sram_idle)(void);
-static void (*omap2_sram_suspend)(int dllctrl, int cpu_rev);
-static void (*saved_idle)(void);
-
-extern void __init pmdomain_init(void);
-extern void pmdomain_set_autoidle(void);
-
-static unsigned int omap24xx_sleep_save[OMAP24XX_SLEEP_SAVE_SIZE];
-
-void omap2_pm_idle(void)
-{
- local_irq_disable();
- local_fiq_disable();
- if (need_resched()) {
- local_fiq_enable();
- local_irq_enable();
- return;
- }
-
- omap2_sram_idle();
- local_fiq_enable();
- local_irq_enable();
-}
-
-static int omap2_pm_prepare(void)
-{
- /* We cannot sleep in idle until we have resumed */
- saved_idle = pm_idle;
- pm_idle = NULL;
- return 0;
-}
-
-static int omap2_pm_suspend(void)
-{
- return 0;
-}
-
-static int omap2_pm_enter(suspend_state_t state)
-{
- int ret = 0;
-
- switch (state)
- {
- case PM_SUSPEND_STANDBY:
- case PM_SUSPEND_MEM:
- ret = omap2_pm_suspend();
- break;
- default:
- ret = -EINVAL;
- }
-
- return ret;
-}
-
-static void omap2_pm_finish(void)
-{
- pm_idle = saved_idle;
-}
-
-static struct platform_suspend_ops omap_pm_ops = {
- .prepare = omap2_pm_prepare,
- .enter = omap2_pm_enter,
- .finish = omap2_pm_finish,
- .valid = suspend_valid_only_mem,
-};
-
-static int __init omap2_pm_init(void)
-{
- return 0;
-}
-
-__initcall(omap2_pm_init);
diff --git a/arch/arm/mach-omap2/pm.h b/arch/arm/mach-omap2/pm.h
new file mode 100644
index 0000000..f7b3baf
--- /dev/null
+++ b/arch/arm/mach-omap2/pm.h
@@ -0,0 +1,38 @@
+/*
+ * OMAP2/3 Power Management Routines
+ *
+ * Copyright (C) 2008 Nokia Corporation
+ * Jouni Hogander
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __ARCH_ARM_MACH_OMAP2_PM_H
+#define __ARCH_ARM_MACH_OMAP2_PM_H
+
+extern int omap2_pm_init(void);
+extern int omap3_pm_init(void);
+
+#ifdef CONFIG_PM_DEBUG
+extern void omap2_pm_dump(int mode, int resume, unsigned int us);
+extern int omap2_pm_debug;
+#else
+#define omap2_pm_dump(mode, resume, us) do {} while (0);
+#define omap2_pm_debug 0
+#endif /* CONFIG_PM_DEBUG */
+
+extern void omap24xx_idle_loop_suspend(void);
+
+extern void omap24xx_cpu_suspend(u32 dll_ctrl, void __iomem *sdrc_dlla_ctrl,
+ void __iomem *sdrc_power);
+extern void omap34xx_cpu_suspend(u32 *addr, int save_state);
+extern void save_secure_ram_context(u32 *addr);
+
+extern unsigned int omap24xx_idle_loop_suspend_sz;
+extern unsigned int omap34xx_suspend_sz;
+extern unsigned int save_secure_ram_context_sz;
+extern unsigned int omap24xx_cpu_suspend_sz;
+extern unsigned int omap34xx_cpu_suspend_sz;
+
+#endif
diff --git a/arch/arm/mach-omap2/pm24xx.c b/arch/arm/mach-omap2/pm24xx.c
new file mode 100644
index 0000000..db10255
--- /dev/null
+++ b/arch/arm/mach-omap2/pm24xx.c
@@ -0,0 +1,549 @@
+/*
+ * OMAP2 Power Management Routines
+ *
+ * Copyright (C) 2005 Texas Instruments, Inc.
+ * Copyright (C) 2006-2008 Nokia Corporation
+ *
+ * Written by:
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Tony Lindgren
+ * Juha Yrjola
+ * Amit Kucheria <amit.kucheria@nokia.com>
+ * Igor Stoppa <igor.stoppa@nokia.com>
+ *
+ * Based on pm.c for omap1
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/suspend.h>
+#include <linux/sched.h>
+#include <linux/proc_fs.h>
+#include <linux/interrupt.h>
+#include <linux/sysfs.h>
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/time.h>
+#include <linux/gpio.h>
+
+#include <asm/mach/time.h>
+#include <asm/mach/irq.h>
+#include <asm/mach-types.h>
+
+#include <mach/irqs.h>
+#include <mach/clock.h>
+#include <mach/sram.h>
+#include <mach/control.h>
+#include <mach/mux.h>
+#include <mach/dma.h>
+#include <mach/board.h>
+
+#include "prm.h"
+#include "prm-regbits-24xx.h"
+#include "cm.h"
+#include "cm-regbits-24xx.h"
+#include "sdrc.h"
+#include "pm.h"
+
+#include <mach/powerdomain.h>
+#include <mach/clockdomain.h>
+
+static void (*omap2_sram_idle)(void);
+static void (*omap2_sram_suspend)(u32 dllctrl, void __iomem *sdrc_dlla_ctrl,
+ void __iomem *sdrc_power);
+
+static struct powerdomain *mpu_pwrdm;
+static struct powerdomain *core_pwrdm;
+
+static struct clockdomain *dsp_clkdm;
+static struct clockdomain *gfx_clkdm;
+
+static struct clk *osc_ck, *emul_ck;
+
+static int omap2_fclks_active(void)
+{
+ u32 f1, f2;
+
+ f1 = cm_read_mod_reg(CORE_MOD, CM_FCLKEN1);
+ f2 = cm_read_mod_reg(CORE_MOD, OMAP24XX_CM_FCLKEN2);
+
+ /* Ignore UART clocks. These are handled by UART core (serial.c) */
+ f1 &= ~(OMAP24XX_EN_UART1 | OMAP24XX_EN_UART2);
+ f2 &= ~OMAP24XX_EN_UART3;
+
+ if (f1 | f2)
+ return 1;
+ return 0;
+}
+
+static void omap2_enter_full_retention(void)
+{
+ u32 l;
+ struct timespec ts_preidle, ts_postidle, ts_idle;
+
+ /* There is 1 reference hold for all children of the oscillator
+ * clock, the following will remove it. If no one else uses the
+ * oscillator itself it will be disabled if/when we enter retention
+ * mode.
+ */
+ clk_disable(osc_ck);
+
+ /* Clear old wake-up events */
+ /* REVISIT: These write to reserved bits? */
+ prm_write_mod_reg(0xffffffff, CORE_MOD, PM_WKST1);
+ prm_write_mod_reg(0xffffffff, CORE_MOD, OMAP24XX_PM_WKST2);
+ prm_write_mod_reg(0xffffffff, WKUP_MOD, PM_WKST);
+
+ /*
+ * Set MPU powerdomain's next power state to RETENTION;
+ * preserve logic state during retention
+ */
+ pwrdm_set_logic_retst(mpu_pwrdm, PWRDM_POWER_RET);
+ pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_RET);
+
+ /* Workaround to kill USB */
+ l = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0) | OMAP24XX_USBSTANDBYCTRL;
+ omap_ctrl_writel(l, OMAP2_CONTROL_DEVCONF0);
+
+ omap2_gpio_prepare_for_retention();
+
+ if (omap2_pm_debug) {
+ omap2_pm_dump(0, 0, 0);
+ getnstimeofday(&ts_preidle);
+ }
+
+ /* One last check for pending IRQs to avoid extra latency due
+ * to sleeping unnecessarily. */
+ if (omap_irq_pending())
+ goto no_sleep;
+
+ omap_uart_prepare_idle(0);
+ omap_uart_prepare_idle(1);
+ omap_uart_prepare_idle(2);
+
+ /* Jump to SRAM suspend code */
+ omap2_sram_suspend(sdrc_read_reg(SDRC_DLLA_CTRL),
+ OMAP_SDRC_REGADDR(SDRC_DLLA_CTRL),
+ OMAP_SDRC_REGADDR(SDRC_POWER));
+
+ omap_uart_resume_idle(2);
+ omap_uart_resume_idle(1);
+ omap_uart_resume_idle(0);
+
+no_sleep:
+ if (omap2_pm_debug) {
+ unsigned long long tmp;
+
+ getnstimeofday(&ts_postidle);
+ ts_idle = timespec_sub(ts_postidle, ts_preidle);
+ tmp = timespec_to_ns(&ts_idle) * NSEC_PER_USEC;
+ omap2_pm_dump(0, 1, tmp);
+ }
+ omap2_gpio_resume_after_retention();
+
+ clk_enable(osc_ck);
+
+ /* clear CORE wake-up events */
+ prm_write_mod_reg(0xffffffff, CORE_MOD, PM_WKST1);
+ prm_write_mod_reg(0xffffffff, CORE_MOD, OMAP24XX_PM_WKST2);
+
+ /* wakeup domain events - bit 1: GPT1, bit5 GPIO */
+ prm_clear_mod_reg_bits(0x4 | 0x1, WKUP_MOD, PM_WKST);
+
+ /* MPU domain wake events */
+ l = prm_read_mod_reg(OCP_MOD, OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
+ if (l & 0x01)
+ prm_write_mod_reg(0x01, OCP_MOD,
+ OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
+ if (l & 0x20)
+ prm_write_mod_reg(0x20, OCP_MOD,
+ OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
+
+ /* Mask future PRCM-to-MPU interrupts */
+ prm_write_mod_reg(0x0, OCP_MOD, OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
+}
+
+static int omap2_i2c_active(void)
+{
+ u32 l;
+
+ l = cm_read_mod_reg(CORE_MOD, CM_FCLKEN1);
+ return l & (OMAP2420_EN_I2C2 | OMAP2420_EN_I2C1);
+}
+
+static int sti_console_enabled;
+
+static int omap2_allow_mpu_retention(void)
+{
+ u32 l;
+
+ /* Check for MMC, UART2, UART1, McSPI2, McSPI1 and DSS1. */
+ l = cm_read_mod_reg(CORE_MOD, CM_FCLKEN1);
+ if (l & (OMAP2420_EN_MMC | OMAP24XX_EN_UART2 |
+ OMAP24XX_EN_UART1 | OMAP24XX_EN_MCSPI2 |
+ OMAP24XX_EN_MCSPI1 | OMAP24XX_EN_DSS1))
+ return 0;
+ /* Check for UART3. */
+ l = cm_read_mod_reg(CORE_MOD, OMAP24XX_CM_FCLKEN2);
+ if (l & OMAP24XX_EN_UART3)
+ return 0;
+ if (sti_console_enabled)
+ return 0;
+
+ return 1;
+}
+
+static void omap2_enter_mpu_retention(void)
+{
+ int only_idle = 0;
+ struct timespec ts_preidle, ts_postidle, ts_idle;
+
+ /* Putting MPU into the WFI state while a transfer is active
+ * seems to cause the I2C block to timeout. Why? Good question. */
+ if (omap2_i2c_active())
+ return;
+
+ /* The peripherals seem not to be able to wake up the MPU when
+ * it is in retention mode. */
+ if (omap2_allow_mpu_retention()) {
+ /* REVISIT: These write to reserved bits? */
+ prm_write_mod_reg(0xffffffff, CORE_MOD, PM_WKST1);
+ prm_write_mod_reg(0xffffffff, CORE_MOD, OMAP24XX_PM_WKST2);
+ prm_write_mod_reg(0xffffffff, WKUP_MOD, PM_WKST);
+
+ /* Try to enter MPU retention */
+ prm_write_mod_reg((0x01 << OMAP_POWERSTATE_SHIFT) |
+ OMAP_LOGICRETSTATE,
+ MPU_MOD, PM_PWSTCTRL);
+ } else {
+ /* Block MPU retention */
+
+ prm_write_mod_reg(OMAP_LOGICRETSTATE, MPU_MOD, PM_PWSTCTRL);
+ only_idle = 1;
+ }
+
+ if (omap2_pm_debug) {
+ omap2_pm_dump(only_idle ? 2 : 1, 0, 0);
+ getnstimeofday(&ts_preidle);
+ }
+
+ omap2_sram_idle();
+
+ if (omap2_pm_debug) {
+ unsigned long long tmp;
+
+ getnstimeofday(&ts_postidle);
+ ts_idle = timespec_sub(ts_postidle, ts_preidle);
+ tmp = timespec_to_ns(&ts_idle) * NSEC_PER_USEC;
+ omap2_pm_dump(only_idle ? 2 : 1, 1, tmp);
+ }
+}
+
+static int omap2_can_sleep(void)
+{
+ if (omap2_fclks_active())
+ return 0;
+ if (osc_ck->usecount > 1)
+ return 0;
+ if (omap_dma_running())
+ return 0;
+
+ return 1;
+}
+
+static void omap2_pm_idle(void)
+{
+ local_irq_disable();
+ local_fiq_disable();
+
+ if (!omap2_can_sleep()) {
+ if (omap_irq_pending())
+ goto out;
+ omap2_enter_mpu_retention();
+ goto out;
+ }
+
+ if (omap_irq_pending())
+ goto out;
+
+ omap2_enter_full_retention();
+
+out:
+ local_fiq_enable();
+ local_irq_enable();
+}
+
+static int omap2_pm_prepare(void)
+{
+ /* We cannot sleep in idle until we have resumed */
+ disable_hlt();
+ return 0;
+}
+
+static int omap2_pm_suspend(void)
+{
+ u32 wken_wkup, mir1;
+
+ wken_wkup = prm_read_mod_reg(WKUP_MOD, PM_WKEN);
+ prm_write_mod_reg(wken_wkup & ~OMAP24XX_EN_GPT1, WKUP_MOD, PM_WKEN);
+
+ /* Mask GPT1 */
+ mir1 = omap_readl(0x480fe0a4);
+ omap_writel(1 << 5, 0x480fe0ac);
+
+ omap_uart_prepare_suspend();
+ omap2_enter_full_retention();
+
+ omap_writel(mir1, 0x480fe0a4);
+ prm_write_mod_reg(wken_wkup, WKUP_MOD, PM_WKEN);
+
+ return 0;
+}
+
+static int omap2_pm_enter(suspend_state_t state)
+{
+ int ret = 0;
+
+ switch (state) {
+ case PM_SUSPEND_STANDBY:
+ case PM_SUSPEND_MEM:
+ ret = omap2_pm_suspend();
+ break;
+ default:
+ ret = -EINVAL;
+ }
+
+ return ret;
+}
+
+static void omap2_pm_finish(void)
+{
+ enable_hlt();
+}
+
+static struct platform_suspend_ops omap_pm_ops = {
+ .prepare = omap2_pm_prepare,
+ .enter = omap2_pm_enter,
+ .finish = omap2_pm_finish,
+ .valid = suspend_valid_only_mem,
+};
+
+static int _pm_clkdm_enable_hwsup(struct clockdomain *clkdm)
+{
+ omap2_clkdm_allow_idle(clkdm);
+ return 0;
+}
+
+static void __init prcm_setup_regs(void)
+{
+ int i, num_mem_banks;
+ struct powerdomain *pwrdm;
+
+ /* Enable autoidle */
+ prm_write_mod_reg(OMAP24XX_AUTOIDLE, OCP_MOD,
+ OMAP2_PRCM_SYSCONFIG_OFFSET);
+
+ /* Set all domain wakeup dependencies */
+ prm_write_mod_reg(OMAP_EN_WKUP_MASK, MPU_MOD, PM_WKDEP);
+ prm_write_mod_reg(0, OMAP24XX_DSP_MOD, PM_WKDEP);
+ prm_write_mod_reg(0, GFX_MOD, PM_WKDEP);
+ prm_write_mod_reg(0, CORE_MOD, PM_WKDEP);
+ if (cpu_is_omap2430())
+ prm_write_mod_reg(0, OMAP2430_MDM_MOD, PM_WKDEP);
+
+ /*
+ * Set CORE powerdomain memory banks to retain their contents
+ * during RETENTION
+ */
+ num_mem_banks = pwrdm_get_mem_bank_count(core_pwrdm);
+ for (i = 0; i < num_mem_banks; i++)
+ pwrdm_set_mem_retst(core_pwrdm, i, PWRDM_POWER_RET);
+
+ /* Set CORE powerdomain's next power state to RETENTION */
+ pwrdm_set_next_pwrst(core_pwrdm, PWRDM_POWER_RET);
+
+ /*
+ * Set MPU powerdomain's next power state to RETENTION;
+ * preserve logic state during retention
+ */
+ pwrdm_set_logic_retst(mpu_pwrdm, PWRDM_POWER_RET);
+ pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_RET);
+
+ /* Force-power down DSP, GFX powerdomains */
+
+ pwrdm = clkdm_get_pwrdm(dsp_clkdm);
+ pwrdm_set_next_pwrst(pwrdm, PWRDM_POWER_OFF);
+ omap2_clkdm_sleep(dsp_clkdm);
+
+ pwrdm = clkdm_get_pwrdm(gfx_clkdm);
+ pwrdm_set_next_pwrst(pwrdm, PWRDM_POWER_OFF);
+ omap2_clkdm_sleep(gfx_clkdm);
+
+ /* Enable clockdomain hardware-supervised control for all clkdms */
+ clkdm_for_each(_pm_clkdm_enable_hwsup);
+
+ /* Enable clock autoidle for all domains */
+ cm_write_mod_reg(OMAP24XX_AUTO_CAM |
+ OMAP24XX_AUTO_MAILBOXES |
+ OMAP24XX_AUTO_WDT4 |
+ OMAP2420_AUTO_WDT3 |
+ OMAP24XX_AUTO_MSPRO |
+ OMAP2420_AUTO_MMC |
+ OMAP24XX_AUTO_FAC |
+ OMAP2420_AUTO_EAC |
+ OMAP24XX_AUTO_HDQ |
+ OMAP24XX_AUTO_UART2 |
+ OMAP24XX_AUTO_UART1 |
+ OMAP24XX_AUTO_I2C2 |
+ OMAP24XX_AUTO_I2C1 |
+ OMAP24XX_AUTO_MCSPI2 |
+ OMAP24XX_AUTO_MCSPI1 |
+ OMAP24XX_AUTO_MCBSP2 |
+ OMAP24XX_AUTO_MCBSP1 |
+ OMAP24XX_AUTO_GPT12 |
+ OMAP24XX_AUTO_GPT11 |
+ OMAP24XX_AUTO_GPT10 |
+ OMAP24XX_AUTO_GPT9 |
+ OMAP24XX_AUTO_GPT8 |
+ OMAP24XX_AUTO_GPT7 |
+ OMAP24XX_AUTO_GPT6 |
+ OMAP24XX_AUTO_GPT5 |
+ OMAP24XX_AUTO_GPT4 |
+ OMAP24XX_AUTO_GPT3 |
+ OMAP24XX_AUTO_GPT2 |
+ OMAP2420_AUTO_VLYNQ |
+ OMAP24XX_AUTO_DSS,
+ CORE_MOD, CM_AUTOIDLE1);
+ cm_write_mod_reg(OMAP24XX_AUTO_UART3 |
+ OMAP24XX_AUTO_SSI |
+ OMAP24XX_AUTO_USB,
+ CORE_MOD, CM_AUTOIDLE2);
+ cm_write_mod_reg(OMAP24XX_AUTO_SDRC |
+ OMAP24XX_AUTO_GPMC |
+ OMAP24XX_AUTO_SDMA,
+ CORE_MOD, CM_AUTOIDLE3);
+ cm_write_mod_reg(OMAP24XX_AUTO_PKA |
+ OMAP24XX_AUTO_AES |
+ OMAP24XX_AUTO_RNG |
+ OMAP24XX_AUTO_SHA |
+ OMAP24XX_AUTO_DES,
+ CORE_MOD, OMAP24XX_CM_AUTOIDLE4);
+
+ cm_write_mod_reg(OMAP2420_AUTO_DSP_IPI, OMAP24XX_DSP_MOD, CM_AUTOIDLE);
+
+ /* Put DPLL and both APLLs into autoidle mode */
+ cm_write_mod_reg((0x03 << OMAP24XX_AUTO_DPLL_SHIFT) |
+ (0x03 << OMAP24XX_AUTO_96M_SHIFT) |
+ (0x03 << OMAP24XX_AUTO_54M_SHIFT),
+ PLL_MOD, CM_AUTOIDLE);
+
+ cm_write_mod_reg(OMAP24XX_AUTO_OMAPCTRL |
+ OMAP24XX_AUTO_WDT1 |
+ OMAP24XX_AUTO_MPU_WDT |
+ OMAP24XX_AUTO_GPIOS |
+ OMAP24XX_AUTO_32KSYNC |
+ OMAP24XX_AUTO_GPT1,
+ WKUP_MOD, CM_AUTOIDLE);
+
+ /* REVISIT: Configure number of 32 kHz clock cycles for sys_clk
+ * stabilisation */
+ prm_write_mod_reg(15 << OMAP_SETUP_TIME_SHIFT, OMAP24XX_GR_MOD,
+ OMAP2_PRCM_CLKSSETUP_OFFSET);
+
+ /* Configure automatic voltage transition */
+ prm_write_mod_reg(2 << OMAP_SETUP_TIME_SHIFT, OMAP24XX_GR_MOD,
+ OMAP2_PRCM_VOLTSETUP_OFFSET);
+ prm_write_mod_reg(OMAP24XX_AUTO_EXTVOLT |
+ (0x1 << OMAP24XX_SETOFF_LEVEL_SHIFT) |
+ OMAP24XX_MEMRETCTRL |
+ (0x1 << OMAP24XX_SETRET_LEVEL_SHIFT) |
+ (0x0 << OMAP24XX_VOLT_LEVEL_SHIFT),
+ OMAP24XX_GR_MOD, OMAP2_PRCM_VOLTCTRL_OFFSET);
+
+ /* Enable wake-up events */
+ prm_write_mod_reg(OMAP24XX_EN_GPIOS | OMAP24XX_EN_GPT1,
+ WKUP_MOD, PM_WKEN);
+}
+
+int __init omap2_pm_init(void)
+{
+ u32 l;
+
+ if (!cpu_is_omap24xx())
+ return -ENODEV;
+
+ printk(KERN_INFO "Power Management for OMAP2 initializing\n");
+ l = prm_read_mod_reg(OCP_MOD, OMAP2_PRCM_REVISION_OFFSET);
+ printk(KERN_INFO "PRCM revision %d.%d\n", (l >> 4) & 0x0f, l & 0x0f);
+
+ /* Look up important powerdomains, clockdomains */
+
+ mpu_pwrdm = pwrdm_lookup("mpu_pwrdm");
+ if (!mpu_pwrdm)
+ pr_err("PM: mpu_pwrdm not found\n");
+
+ core_pwrdm = pwrdm_lookup("core_pwrdm");
+ if (!core_pwrdm)
+ pr_err("PM: core_pwrdm not found\n");
+
+ dsp_clkdm = clkdm_lookup("dsp_clkdm");
+ if (!dsp_clkdm)
+ pr_err("PM: mpu_clkdm not found\n");
+
+ gfx_clkdm = clkdm_lookup("gfx_clkdm");
+ if (!gfx_clkdm)
+ pr_err("PM: gfx_clkdm not found\n");
+
+
+ osc_ck = clk_get(NULL, "osc_ck");
+ if (IS_ERR(osc_ck)) {
+ printk(KERN_ERR "could not get osc_ck\n");
+ return -ENODEV;
+ }
+
+ if (cpu_is_omap242x()) {
+ emul_ck = clk_get(NULL, "emul_ck");
+ if (IS_ERR(emul_ck)) {
+ printk(KERN_ERR "could not get emul_ck\n");
+ clk_put(osc_ck);
+ return -ENODEV;
+ }
+ }
+
+ prcm_setup_regs();
+
+ /* Hack to prevent MPU retention when STI console is enabled. */
+ {
+ const struct omap_sti_console_config *sti;
+
+ sti = omap_get_config(OMAP_TAG_STI_CONSOLE,
+ struct omap_sti_console_config);
+ if (sti != NULL && sti->enable)
+ sti_console_enabled = 1;
+ }
+
+ /*
+ * We copy the assembler sleep/wakeup routines to SRAM.
+ * These routines need to be in SRAM as that's the only
+ * memory the MPU can see when it wakes up.
+ */
+ if (cpu_is_omap24xx()) {
+ omap2_sram_idle = omap_sram_push(omap24xx_idle_loop_suspend,
+ omap24xx_idle_loop_suspend_sz);
+
+ omap2_sram_suspend = omap_sram_push(omap24xx_cpu_suspend,
+ omap24xx_cpu_suspend_sz);
+ }
+
+ suspend_set_ops(&omap_pm_ops);
+ pm_idle = omap2_pm_idle;
+
+ return 0;
+}
+
+late_initcall(omap2_pm_init);
diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c
new file mode 100644
index 0000000..841d4c5
--- /dev/null
+++ b/arch/arm/mach-omap2/pm34xx.c
@@ -0,0 +1,710 @@
+/*
+ * OMAP3 Power Management Routines
+ *
+ * Copyright (C) 2006-2008 Nokia Corporation
+ * Tony Lindgren <tony@atomide.com>
+ * Jouni Hogander
+ *
+ * Copyright (C) 2005 Texas Instruments, Inc.
+ * Richard Woodruff <r-woodruff2@ti.com>
+ *
+ * Based on pm.c for omap1
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/pm.h>
+#include <linux/suspend.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/list.h>
+#include <linux/err.h>
+#include <linux/gpio.h>
+
+#include <mach/sram.h>
+#include <mach/clockdomain.h>
+#include <mach/powerdomain.h>
+#include <mach/control.h>
+#include <mach/serial.h>
+
+#include "cm.h"
+#include "cm-regbits-34xx.h"
+#include "prm-regbits-34xx.h"
+
+#include "prm.h"
+#include "pm.h"
+
+struct power_state {
+ struct powerdomain *pwrdm;
+ u32 next_state;
+ u32 saved_state;
+ struct list_head node;
+};
+
+static LIST_HEAD(pwrst_list);
+
+static void (*_omap_sram_idle)(u32 *addr, int save_state);
+
+static struct powerdomain *mpu_pwrdm;
+
+/* PRCM Interrupt Handler for wakeups */
+static irqreturn_t prcm_interrupt_handler (int irq, void *dev_id)
+{
+ u32 wkst, irqstatus_mpu;
+ u32 fclk, iclk;
+
+ /* WKUP */
+ wkst = prm_read_mod_reg(WKUP_MOD, PM_WKST);
+ if (wkst) {
+ iclk = cm_read_mod_reg(WKUP_MOD, CM_ICLKEN);
+ fclk = cm_read_mod_reg(WKUP_MOD, CM_FCLKEN);
+ cm_set_mod_reg_bits(wkst, WKUP_MOD, CM_ICLKEN);
+ cm_set_mod_reg_bits(wkst, WKUP_MOD, CM_FCLKEN);
+ prm_write_mod_reg(wkst, WKUP_MOD, PM_WKST);
+ while (prm_read_mod_reg(WKUP_MOD, PM_WKST))
+ cpu_relax();
+ cm_write_mod_reg(iclk, WKUP_MOD, CM_ICLKEN);
+ cm_write_mod_reg(fclk, WKUP_MOD, CM_FCLKEN);
+ }
+
+ /* CORE */
+ wkst = prm_read_mod_reg(CORE_MOD, PM_WKST1);
+ if (wkst) {
+ iclk = cm_read_mod_reg(CORE_MOD, CM_ICLKEN1);
+ fclk = cm_read_mod_reg(CORE_MOD, CM_FCLKEN1);
+ cm_set_mod_reg_bits(wkst, CORE_MOD, CM_ICLKEN1);
+ cm_set_mod_reg_bits(wkst, CORE_MOD, CM_FCLKEN1);
+ prm_write_mod_reg(wkst, CORE_MOD, PM_WKST1);
+ while (prm_read_mod_reg(CORE_MOD, PM_WKST1))
+ cpu_relax();
+ cm_write_mod_reg(iclk, CORE_MOD, CM_ICLKEN1);
+ cm_write_mod_reg(fclk, CORE_MOD, CM_FCLKEN1);
+ }
+ wkst = prm_read_mod_reg(CORE_MOD, OMAP3430ES2_PM_WKST3);
+ if (wkst) {
+ iclk = cm_read_mod_reg(CORE_MOD, CM_ICLKEN3);
+ fclk = cm_read_mod_reg(CORE_MOD, OMAP3430ES2_CM_FCLKEN3);
+ cm_set_mod_reg_bits(wkst, CORE_MOD, CM_ICLKEN3);
+ cm_set_mod_reg_bits(wkst, CORE_MOD, OMAP3430ES2_CM_FCLKEN3);
+ prm_write_mod_reg(wkst, CORE_MOD, OMAP3430ES2_PM_WKST3);
+ while (prm_read_mod_reg(CORE_MOD, OMAP3430ES2_PM_WKST3))
+ cpu_relax();
+ cm_write_mod_reg(iclk, CORE_MOD, CM_ICLKEN3);
+ cm_write_mod_reg(fclk, CORE_MOD, OMAP3430ES2_CM_FCLKEN3);
+ }
+
+ /* PER */
+ wkst = prm_read_mod_reg(OMAP3430_PER_MOD, PM_WKST);
+ if (wkst) {
+ iclk = cm_read_mod_reg(OMAP3430_PER_MOD, CM_ICLKEN);
+ fclk = cm_read_mod_reg(OMAP3430_PER_MOD, CM_FCLKEN);
+ cm_set_mod_reg_bits(wkst, OMAP3430_PER_MOD, CM_ICLKEN);
+ cm_set_mod_reg_bits(wkst, OMAP3430_PER_MOD, CM_FCLKEN);
+ prm_write_mod_reg(wkst, OMAP3430_PER_MOD, PM_WKST);
+ while (prm_read_mod_reg(OMAP3430_PER_MOD, PM_WKST))
+ cpu_relax();
+ cm_write_mod_reg(iclk, OMAP3430_PER_MOD, CM_ICLKEN);
+ cm_write_mod_reg(fclk, OMAP3430_PER_MOD, CM_FCLKEN);
+ }
+
+ if (omap_rev() > OMAP3430_REV_ES1_0) {
+ /* USBHOST */
+ wkst = prm_read_mod_reg(OMAP3430ES2_USBHOST_MOD, PM_WKST);
+ if (wkst) {
+ iclk = cm_read_mod_reg(OMAP3430ES2_USBHOST_MOD,
+ CM_ICLKEN);
+ fclk = cm_read_mod_reg(OMAP3430ES2_USBHOST_MOD,
+ CM_FCLKEN);
+ cm_set_mod_reg_bits(wkst, OMAP3430ES2_USBHOST_MOD,
+ CM_ICLKEN);
+ cm_set_mod_reg_bits(wkst, OMAP3430ES2_USBHOST_MOD,
+ CM_FCLKEN);
+ prm_write_mod_reg(wkst, OMAP3430ES2_USBHOST_MOD,
+ PM_WKST);
+ while (prm_read_mod_reg(OMAP3430ES2_USBHOST_MOD,
+ PM_WKST))
+ cpu_relax();
+ cm_write_mod_reg(iclk, OMAP3430ES2_USBHOST_MOD,
+ CM_ICLKEN);
+ cm_write_mod_reg(fclk, OMAP3430ES2_USBHOST_MOD,
+ CM_FCLKEN);
+ }
+ }
+
+ irqstatus_mpu = prm_read_mod_reg(OCP_MOD,
+ OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
+ prm_write_mod_reg(irqstatus_mpu, OCP_MOD,
+ OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
+
+ while (prm_read_mod_reg(OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET))
+ cpu_relax();
+
+ return IRQ_HANDLED;
+}
+
+static void omap_sram_idle(void)
+{
+ /* Variable to tell what needs to be saved and restored
+ * in omap_sram_idle*/
+ /* save_state = 0 => Nothing to save and restored */
+ /* save_state = 1 => Only L1 and logic lost */
+ /* save_state = 2 => Only L2 lost */
+ /* save_state = 3 => L1, L2 and logic lost */
+ int save_state = 0, mpu_next_state;
+
+ if (!_omap_sram_idle)
+ return;
+
+ mpu_next_state = pwrdm_read_next_pwrst(mpu_pwrdm);
+ switch (mpu_next_state) {
+ case PWRDM_POWER_RET:
+ /* No need to save context */
+ save_state = 0;
+ break;
+ default:
+ /* Invalid state */
+ printk(KERN_ERR "Invalid mpu state in sram_idle\n");
+ return;
+ }
+ omap2_gpio_prepare_for_retention();
+ omap_uart_prepare_idle(0);
+ omap_uart_prepare_idle(1);
+ omap_uart_prepare_idle(2);
+
+ _omap_sram_idle(NULL, save_state);
+ cpu_init();
+
+ omap_uart_resume_idle(2);
+ omap_uart_resume_idle(1);
+ omap_uart_resume_idle(0);
+ omap2_gpio_resume_after_retention();
+}
+
+/*
+ * Check if functional clocks are enabled before entering
+ * sleep. This function could be behind CONFIG_PM_DEBUG
+ * when all drivers are configuring their sysconfig registers
+ * properly and using their clocks properly.
+ */
+static int omap3_fclks_active(void)
+{
+ u32 fck_core1 = 0, fck_core3 = 0, fck_sgx = 0, fck_dss = 0,
+ fck_cam = 0, fck_per = 0, fck_usbhost = 0;
+
+ fck_core1 = cm_read_mod_reg(CORE_MOD,
+ CM_FCLKEN1);
+ if (omap_rev() > OMAP3430_REV_ES1_0) {
+ fck_core3 = cm_read_mod_reg(CORE_MOD,
+ OMAP3430ES2_CM_FCLKEN3);
+ fck_sgx = cm_read_mod_reg(OMAP3430ES2_SGX_MOD,
+ CM_FCLKEN);
+ fck_usbhost = cm_read_mod_reg(OMAP3430ES2_USBHOST_MOD,
+ CM_FCLKEN);
+ } else
+ fck_sgx = cm_read_mod_reg(GFX_MOD,
+ OMAP3430ES2_CM_FCLKEN3);
+ fck_dss = cm_read_mod_reg(OMAP3430_DSS_MOD,
+ CM_FCLKEN);
+ fck_cam = cm_read_mod_reg(OMAP3430_CAM_MOD,
+ CM_FCLKEN);
+ fck_per = cm_read_mod_reg(OMAP3430_PER_MOD,
+ CM_FCLKEN);
+
+ /* Ignore UART clocks. These are handled by UART core (serial.c) */
+ fck_core1 &= ~(OMAP3430_EN_UART1 | OMAP3430_EN_UART2);
+ fck_per &= ~OMAP3430_EN_UART3;
+
+ if (fck_core1 | fck_core3 | fck_sgx | fck_dss |
+ fck_cam | fck_per | fck_usbhost)
+ return 1;
+ return 0;
+}
+
+static int omap3_can_sleep(void)
+{
+ if (!omap_uart_can_sleep())
+ return 0;
+ if (omap3_fclks_active())
+ return 0;
+ return 1;
+}
+
+/* This sets pwrdm state (other than mpu & core. Currently only ON &
+ * RET are supported. Function is assuming that clkdm doesn't have
+ * hw_sup mode enabled. */
+static int set_pwrdm_state(struct powerdomain *pwrdm, u32 state)
+{
+ u32 cur_state;
+ int sleep_switch = 0;
+ int ret = 0;
+
+ if (pwrdm == NULL || IS_ERR(pwrdm))
+ return -EINVAL;
+
+ while (!(pwrdm->pwrsts & (1 << state))) {
+ if (state == PWRDM_POWER_OFF)
+ return ret;
+ state--;
+ }
+
+ cur_state = pwrdm_read_next_pwrst(pwrdm);
+ if (cur_state == state)
+ return ret;
+
+ if (pwrdm_read_pwrst(pwrdm) < PWRDM_POWER_ON) {
+ omap2_clkdm_wakeup(pwrdm->pwrdm_clkdms[0]);
+ sleep_switch = 1;
+ pwrdm_wait_transition(pwrdm);
+ }
+
+ ret = pwrdm_set_next_pwrst(pwrdm, state);
+ if (ret) {
+ printk(KERN_ERR "Unable to set state of powerdomain: %s\n",
+ pwrdm->name);
+ goto err;
+ }
+
+ if (sleep_switch) {
+ omap2_clkdm_allow_idle(pwrdm->pwrdm_clkdms[0]);
+ pwrdm_wait_transition(pwrdm);
+ }
+
+err:
+ return ret;
+}
+
+static void omap3_pm_idle(void)
+{
+ local_irq_disable();
+ local_fiq_disable();
+
+ if (!omap3_can_sleep())
+ goto out;
+
+ if (omap_irq_pending())
+ goto out;
+
+ omap_sram_idle();
+
+out:
+ local_fiq_enable();
+ local_irq_enable();
+}
+
+static int omap3_pm_prepare(void)
+{
+ disable_hlt();
+ return 0;
+}
+
+static int omap3_pm_suspend(void)
+{
+ struct power_state *pwrst;
+ int state, ret = 0;
+
+ /* Read current next_pwrsts */
+ list_for_each_entry(pwrst, &pwrst_list, node)
+ pwrst->saved_state = pwrdm_read_next_pwrst(pwrst->pwrdm);
+ /* Set ones wanted by suspend */
+ list_for_each_entry(pwrst, &pwrst_list, node) {
+ if (set_pwrdm_state(pwrst->pwrdm, pwrst->next_state))
+ goto restore;
+ if (pwrdm_clear_all_prev_pwrst(pwrst->pwrdm))
+ goto restore;
+ }
+
+ omap_uart_prepare_suspend();
+ omap_sram_idle();
+
+restore:
+ /* Restore next_pwrsts */
+ list_for_each_entry(pwrst, &pwrst_list, node) {
+ set_pwrdm_state(pwrst->pwrdm, pwrst->saved_state);
+ state = pwrdm_read_prev_pwrst(pwrst->pwrdm);
+ if (state > pwrst->next_state) {
+ printk(KERN_INFO "Powerdomain (%s) didn't enter "
+ "target state %d\n",
+ pwrst->pwrdm->name, pwrst->next_state);
+ ret = -1;
+ }
+ }
+ if (ret)
+ printk(KERN_ERR "Could not enter target state in pm_suspend\n");
+ else
+ printk(KERN_INFO "Successfully put all powerdomains "
+ "to target state\n");
+
+ return ret;
+}
+
+static int omap3_pm_enter(suspend_state_t state)
+{
+ int ret = 0;
+
+ switch (state) {
+ case PM_SUSPEND_STANDBY:
+ case PM_SUSPEND_MEM:
+ ret = omap3_pm_suspend();
+ break;
+ default:
+ ret = -EINVAL;
+ }
+
+ return ret;
+}
+
+static void omap3_pm_finish(void)
+{
+ enable_hlt();
+}
+
+static struct platform_suspend_ops omap_pm_ops = {
+ .prepare = omap3_pm_prepare,
+ .enter = omap3_pm_enter,
+ .finish = omap3_pm_finish,
+ .valid = suspend_valid_only_mem,
+};
+
+
+/**
+ * omap3_iva_idle(): ensure IVA is in idle so it can be put into
+ * retention
+ *
+ * In cases where IVA2 is activated by bootcode, it may prevent
+ * full-chip retention or off-mode because it is not idle. This
+ * function forces the IVA2 into idle state so it can go
+ * into retention/off and thus allow full-chip retention/off.
+ *
+ **/
+static void __init omap3_iva_idle(void)
+{
+ /* ensure IVA2 clock is disabled */
+ cm_write_mod_reg(0, OMAP3430_IVA2_MOD, CM_FCLKEN);
+
+ /* if no clock activity, nothing else to do */
+ if (!(cm_read_mod_reg(OMAP3430_IVA2_MOD, OMAP3430_CM_CLKSTST) &
+ OMAP3430_CLKACTIVITY_IVA2_MASK))
+ return;
+
+ /* Reset IVA2 */
+ prm_write_mod_reg(OMAP3430_RST1_IVA2 |
+ OMAP3430_RST2_IVA2 |
+ OMAP3430_RST3_IVA2,
+ OMAP3430_IVA2_MOD, RM_RSTCTRL);
+
+ /* Enable IVA2 clock */
+ cm_write_mod_reg(OMAP3430_CM_FCLKEN_IVA2_EN_IVA2,
+ OMAP3430_IVA2_MOD, CM_FCLKEN);
+
+ /* Set IVA2 boot mode to 'idle' */
+ omap_ctrl_writel(OMAP3_IVA2_BOOTMOD_IDLE,
+ OMAP343X_CONTROL_IVA2_BOOTMOD);
+
+ /* Un-reset IVA2 */
+ prm_write_mod_reg(0, OMAP3430_IVA2_MOD, RM_RSTCTRL);
+
+ /* Disable IVA2 clock */
+ cm_write_mod_reg(0, OMAP3430_IVA2_MOD, CM_FCLKEN);
+
+ /* Reset IVA2 */
+ prm_write_mod_reg(OMAP3430_RST1_IVA2 |
+ OMAP3430_RST2_IVA2 |
+ OMAP3430_RST3_IVA2,
+ OMAP3430_IVA2_MOD, RM_RSTCTRL);
+}
+
+static void __init omap3_d2d_idle(void)
+{
+ u16 mask, padconf;
+
+ /* In a stand alone OMAP3430 where there is not a stacked
+ * modem for the D2D Idle Ack and D2D MStandby must be pulled
+ * high. S CONTROL_PADCONF_SAD2D_IDLEACK and
+ * CONTROL_PADCONF_SAD2D_MSTDBY to have a pull up. */
+ mask = (1 << 4) | (1 << 3); /* pull-up, enabled */
+ padconf = omap_ctrl_readw(OMAP3_PADCONF_SAD2D_MSTANDBY);
+ padconf |= mask;
+ omap_ctrl_writew(padconf, OMAP3_PADCONF_SAD2D_MSTANDBY);
+
+ padconf = omap_ctrl_readw(OMAP3_PADCONF_SAD2D_IDLEACK);
+ padconf |= mask;
+ omap_ctrl_writew(padconf, OMAP3_PADCONF_SAD2D_IDLEACK);
+
+ /* reset modem */
+ prm_write_mod_reg(OMAP3430_RM_RSTCTRL_CORE_MODEM_SW_RSTPWRON |
+ OMAP3430_RM_RSTCTRL_CORE_MODEM_SW_RST,
+ CORE_MOD, RM_RSTCTRL);
+ prm_write_mod_reg(0, CORE_MOD, RM_RSTCTRL);
+}
+
+static void __init prcm_setup_regs(void)
+{
+ /* XXX Reset all wkdeps. This should be done when initializing
+ * powerdomains */
+ prm_write_mod_reg(0, OMAP3430_IVA2_MOD, PM_WKDEP);
+ prm_write_mod_reg(0, MPU_MOD, PM_WKDEP);
+ prm_write_mod_reg(0, OMAP3430_DSS_MOD, PM_WKDEP);
+ prm_write_mod_reg(0, OMAP3430_NEON_MOD, PM_WKDEP);
+ prm_write_mod_reg(0, OMAP3430_CAM_MOD, PM_WKDEP);
+ prm_write_mod_reg(0, OMAP3430_PER_MOD, PM_WKDEP);
+ if (omap_rev() > OMAP3430_REV_ES1_0) {
+ prm_write_mod_reg(0, OMAP3430ES2_SGX_MOD, PM_WKDEP);
+ prm_write_mod_reg(0, OMAP3430ES2_USBHOST_MOD, PM_WKDEP);
+ } else
+ prm_write_mod_reg(0, GFX_MOD, PM_WKDEP);
+
+ /*
+ * Enable interface clock autoidle for all modules.
+ * Note that in the long run this should be done by clockfw
+ */
+ cm_write_mod_reg(
+ OMAP3430_AUTO_MODEM |
+ OMAP3430ES2_AUTO_MMC3 |
+ OMAP3430ES2_AUTO_ICR |
+ OMAP3430_AUTO_AES2 |
+ OMAP3430_AUTO_SHA12 |
+ OMAP3430_AUTO_DES2 |
+ OMAP3430_AUTO_MMC2 |
+ OMAP3430_AUTO_MMC1 |
+ OMAP3430_AUTO_MSPRO |
+ OMAP3430_AUTO_HDQ |
+ OMAP3430_AUTO_MCSPI4 |
+ OMAP3430_AUTO_MCSPI3 |
+ OMAP3430_AUTO_MCSPI2 |
+ OMAP3430_AUTO_MCSPI1 |
+ OMAP3430_AUTO_I2C3 |
+ OMAP3430_AUTO_I2C2 |
+ OMAP3430_AUTO_I2C1 |
+ OMAP3430_AUTO_UART2 |
+ OMAP3430_AUTO_UART1 |
+ OMAP3430_AUTO_GPT11 |
+ OMAP3430_AUTO_GPT10 |
+ OMAP3430_AUTO_MCBSP5 |
+ OMAP3430_AUTO_MCBSP1 |
+ OMAP3430ES1_AUTO_FAC | /* This is es1 only */
+ OMAP3430_AUTO_MAILBOXES |
+ OMAP3430_AUTO_OMAPCTRL |
+ OMAP3430ES1_AUTO_FSHOSTUSB |
+ OMAP3430_AUTO_HSOTGUSB |
+ OMAP3430_AUTO_SAD2D |
+ OMAP3430_AUTO_SSI,
+ CORE_MOD, CM_AUTOIDLE1);
+
+ cm_write_mod_reg(
+ OMAP3430_AUTO_PKA |
+ OMAP3430_AUTO_AES1 |
+ OMAP3430_AUTO_RNG |
+ OMAP3430_AUTO_SHA11 |
+ OMAP3430_AUTO_DES1,
+ CORE_MOD, CM_AUTOIDLE2);
+
+ if (omap_rev() > OMAP3430_REV_ES1_0) {
+ cm_write_mod_reg(
+ OMAP3430_AUTO_MAD2D |
+ OMAP3430ES2_AUTO_USBTLL,
+ CORE_MOD, CM_AUTOIDLE3);
+ }
+
+ cm_write_mod_reg(
+ OMAP3430_AUTO_WDT2 |
+ OMAP3430_AUTO_WDT1 |
+ OMAP3430_AUTO_GPIO1 |
+ OMAP3430_AUTO_32KSYNC |
+ OMAP3430_AUTO_GPT12 |
+ OMAP3430_AUTO_GPT1 ,
+ WKUP_MOD, CM_AUTOIDLE);
+
+ cm_write_mod_reg(
+ OMAP3430_AUTO_DSS,
+ OMAP3430_DSS_MOD,
+ CM_AUTOIDLE);
+
+ cm_write_mod_reg(
+ OMAP3430_AUTO_CAM,
+ OMAP3430_CAM_MOD,
+ CM_AUTOIDLE);
+
+ cm_write_mod_reg(
+ OMAP3430_AUTO_GPIO6 |
+ OMAP3430_AUTO_GPIO5 |
+ OMAP3430_AUTO_GPIO4 |
+ OMAP3430_AUTO_GPIO3 |
+ OMAP3430_AUTO_GPIO2 |
+ OMAP3430_AUTO_WDT3 |
+ OMAP3430_AUTO_UART3 |
+ OMAP3430_AUTO_GPT9 |
+ OMAP3430_AUTO_GPT8 |
+ OMAP3430_AUTO_GPT7 |
+ OMAP3430_AUTO_GPT6 |
+ OMAP3430_AUTO_GPT5 |
+ OMAP3430_AUTO_GPT4 |
+ OMAP3430_AUTO_GPT3 |
+ OMAP3430_AUTO_GPT2 |
+ OMAP3430_AUTO_MCBSP4 |
+ OMAP3430_AUTO_MCBSP3 |
+ OMAP3430_AUTO_MCBSP2,
+ OMAP3430_PER_MOD,
+ CM_AUTOIDLE);
+
+ if (omap_rev() > OMAP3430_REV_ES1_0) {
+ cm_write_mod_reg(
+ OMAP3430ES2_AUTO_USBHOST,
+ OMAP3430ES2_USBHOST_MOD,
+ CM_AUTOIDLE);
+ }
+
+ /*
+ * Set all plls to autoidle. This is needed until autoidle is
+ * enabled by clockfw
+ */
+ cm_write_mod_reg(1 << OMAP3430_AUTO_IVA2_DPLL_SHIFT,
+ OMAP3430_IVA2_MOD, CM_AUTOIDLE2);
+ cm_write_mod_reg(1 << OMAP3430_AUTO_MPU_DPLL_SHIFT,
+ MPU_MOD,
+ CM_AUTOIDLE2);
+ cm_write_mod_reg((1 << OMAP3430_AUTO_PERIPH_DPLL_SHIFT) |
+ (1 << OMAP3430_AUTO_CORE_DPLL_SHIFT),
+ PLL_MOD,
+ CM_AUTOIDLE);
+ cm_write_mod_reg(1 << OMAP3430ES2_AUTO_PERIPH2_DPLL_SHIFT,
+ PLL_MOD,
+ CM_AUTOIDLE2);
+
+ /*
+ * Enable control of expternal oscillator through
+ * sys_clkreq. In the long run clock framework should
+ * take care of this.
+ */
+ prm_rmw_mod_reg_bits(OMAP_AUTOEXTCLKMODE_MASK,
+ 1 << OMAP_AUTOEXTCLKMODE_SHIFT,
+ OMAP3430_GR_MOD,
+ OMAP3_PRM_CLKSRC_CTRL_OFFSET);
+
+ /* setup wakup source */
+ prm_write_mod_reg(OMAP3430_EN_IO | OMAP3430_EN_GPIO1 |
+ OMAP3430_EN_GPT1 | OMAP3430_EN_GPT12,
+ WKUP_MOD, PM_WKEN);
+ /* No need to write EN_IO, that is always enabled */
+ prm_write_mod_reg(OMAP3430_EN_GPIO1 | OMAP3430_EN_GPT1 |
+ OMAP3430_EN_GPT12,
+ WKUP_MOD, OMAP3430_PM_MPUGRPSEL);
+ /* For some reason IO doesn't generate wakeup event even if
+ * it is selected to mpu wakeup goup */
+ prm_write_mod_reg(OMAP3430_IO_EN | OMAP3430_WKUP_EN,
+ OCP_MOD, OMAP3_PRM_IRQENABLE_MPU_OFFSET);
+
+ /* Don't attach IVA interrupts */
+ prm_write_mod_reg(0, WKUP_MOD, OMAP3430_PM_IVAGRPSEL);
+ prm_write_mod_reg(0, CORE_MOD, OMAP3430_PM_IVAGRPSEL1);
+ prm_write_mod_reg(0, CORE_MOD, OMAP3430ES2_PM_IVAGRPSEL3);
+ prm_write_mod_reg(0, OMAP3430_PER_MOD, OMAP3430_PM_IVAGRPSEL);
+
+ /* Clear any pending 'reset' flags */
+ prm_write_mod_reg(0xffffffff, MPU_MOD, RM_RSTST);
+ prm_write_mod_reg(0xffffffff, CORE_MOD, RM_RSTST);
+ prm_write_mod_reg(0xffffffff, OMAP3430_PER_MOD, RM_RSTST);
+ prm_write_mod_reg(0xffffffff, OMAP3430_EMU_MOD, RM_RSTST);
+ prm_write_mod_reg(0xffffffff, OMAP3430_NEON_MOD, RM_RSTST);
+ prm_write_mod_reg(0xffffffff, OMAP3430_DSS_MOD, RM_RSTST);
+ prm_write_mod_reg(0xffffffff, OMAP3430ES2_USBHOST_MOD, RM_RSTST);
+
+ /* Clear any pending PRCM interrupts */
+ prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
+
+ omap3_iva_idle();
+ omap3_d2d_idle();
+}
+
+static int __init pwrdms_setup(struct powerdomain *pwrdm)
+{
+ struct power_state *pwrst;
+
+ if (!pwrdm->pwrsts)
+ return 0;
+
+ pwrst = kmalloc(sizeof(struct power_state), GFP_KERNEL);
+ if (!pwrst)
+ return -ENOMEM;
+ pwrst->pwrdm = pwrdm;
+ pwrst->next_state = PWRDM_POWER_RET;
+ list_add(&pwrst->node, &pwrst_list);
+
+ if (pwrdm_has_hdwr_sar(pwrdm))
+ pwrdm_enable_hdwr_sar(pwrdm);
+
+ return set_pwrdm_state(pwrst->pwrdm, pwrst->next_state);
+}
+
+/*
+ * Enable hw supervised mode for all clockdomains if it's
+ * supported. Initiate sleep transition for other clockdomains, if
+ * they are not used
+ */
+static int __init clkdms_setup(struct clockdomain *clkdm)
+{
+ if (clkdm->flags & CLKDM_CAN_ENABLE_AUTO)
+ omap2_clkdm_allow_idle(clkdm);
+ else if (clkdm->flags & CLKDM_CAN_FORCE_SLEEP &&
+ atomic_read(&clkdm->usecount) == 0)
+ omap2_clkdm_sleep(clkdm);
+ return 0;
+}
+
+int __init omap3_pm_init(void)
+{
+ struct power_state *pwrst, *tmp;
+ int ret;
+
+ if (!cpu_is_omap34xx())
+ return -ENODEV;
+
+ printk(KERN_ERR "Power Management for TI OMAP3.\n");
+
+ /* XXX prcm_setup_regs needs to be before enabling hw
+ * supervised mode for powerdomains */
+ prcm_setup_regs();
+
+ ret = request_irq(INT_34XX_PRCM_MPU_IRQ,
+ (irq_handler_t)prcm_interrupt_handler,
+ IRQF_DISABLED, "prcm", NULL);
+ if (ret) {
+ printk(KERN_ERR "request_irq failed to register for 0x%x\n",
+ INT_34XX_PRCM_MPU_IRQ);
+ goto err1;
+ }
+
+ ret = pwrdm_for_each(pwrdms_setup);
+ if (ret) {
+ printk(KERN_ERR "Failed to setup powerdomains\n");
+ goto err2;
+ }
+
+ (void) clkdm_for_each(clkdms_setup);
+
+ mpu_pwrdm = pwrdm_lookup("mpu_pwrdm");
+ if (mpu_pwrdm == NULL) {
+ printk(KERN_ERR "Failed to get mpu_pwrdm\n");
+ goto err2;
+ }
+
+ _omap_sram_idle = omap_sram_push(omap34xx_cpu_suspend,
+ omap34xx_cpu_suspend_sz);
+
+ suspend_set_ops(&omap_pm_ops);
+
+ pm_idle = omap3_pm_idle;
+
+err1:
+ return ret;
+err2:
+ free_irq(INT_34XX_PRCM_MPU_IRQ, NULL);
+ list_for_each_entry_safe(pwrst, tmp, &pwrst_list, node) {
+ list_del(&pwrst->node);
+ kfree(pwrst);
+ }
+ return ret;
+}
+
+late_initcall(omap3_pm_init);
diff --git a/arch/arm/mach-omap2/prcm-common.h b/arch/arm/mach-omap2/prcm-common.h
index 812d50e..cb1ae84 100644
--- a/arch/arm/mach-omap2/prcm-common.h
+++ b/arch/arm/mach-omap2/prcm-common.h
@@ -276,6 +276,8 @@
/* CM_FCLKEN_WKUP, CM_ICLKEN_WKUP, PM_WKEN_WKUP shared bits */
#define OMAP3430_EN_GPIO1 (1 << 3)
#define OMAP3430_EN_GPIO1_SHIFT 3
+#define OMAP3430_EN_GPT12 (1 << 1)
+#define OMAP3430_EN_GPT12_SHIFT 1
#define OMAP3430_EN_GPT1 (1 << 0)
#define OMAP3430_EN_GPT1_SHIFT 0
diff --git a/arch/arm/mach-omap2/prm.h b/arch/arm/mach-omap2/prm.h
index 7c8e0c4..9937e28 100644
--- a/arch/arm/mach-omap2/prm.h
+++ b/arch/arm/mach-omap2/prm.h
@@ -203,9 +203,11 @@
#define OMAP3430_PM_MPUGRPSEL 0x00a4
#define OMAP3430_PM_MPUGRPSEL1 OMAP3430_PM_MPUGRPSEL
+#define OMAP3430ES2_PM_MPUGRPSEL3 0x00f8
#define OMAP3430_PM_IVAGRPSEL 0x00a8
#define OMAP3430_PM_IVAGRPSEL1 OMAP3430_PM_IVAGRPSEL
+#define OMAP3430ES2_PM_IVAGRPSEL3 0x00f4
#define OMAP3430_PM_PREPWSTST 0x00e8
diff --git a/arch/arm/mach-omap2/sdrc.c b/arch/arm/mach-omap2/sdrc.c
index 2a30060..2045441 100644
--- a/arch/arm/mach-omap2/sdrc.c
+++ b/arch/arm/mach-omap2/sdrc.c
@@ -37,6 +37,10 @@
void __iomem *omap2_sdrc_base;
void __iomem *omap2_sms_base;
+/* SDRC_POWER register bits */
+#define SDRC_POWER_EXTCLKDIS_SHIFT 3
+#define SDRC_POWER_PWDENA_SHIFT 2
+#define SDRC_POWER_PAGEPOLICY_SHIFT 0
/**
* omap2_sdrc_get_params - return SDRC register values for a given clock rate
@@ -56,9 +60,12 @@
{
struct omap_sdrc_params *sp;
+ if (!sdrc_init_params)
+ return NULL;
+
sp = sdrc_init_params;
- while (sp->rate != r)
+ while (sp->rate && sp->rate != r)
sp++;
if (!sp->rate)
@@ -74,7 +81,14 @@
omap2_sms_base = omap2_globals->sms;
}
-/* turn on smart idle modes for SDRAM scheduler and controller */
+/**
+ * omap2_sdrc_init - initialize SMS, SDRC devices on boot
+ * @sp: pointer to a null-terminated list of struct omap_sdrc_params
+ *
+ * Turn on smart idle modes for SDRAM scheduler and controller.
+ * Program a known-good configuration for the SDRC to deal with buggy
+ * bootloaders.
+ */
void __init omap2_sdrc_init(struct omap_sdrc_params *sp)
{
u32 l;
@@ -90,4 +104,10 @@
sdrc_write_reg(l, SDRC_SYSCONFIG);
sdrc_init_params = sp;
+
+ /* XXX Enable SRFRONIDLEREQ here also? */
+ l = (1 << SDRC_POWER_EXTCLKDIS_SHIFT) |
+ (1 << SDRC_POWER_PWDENA_SHIFT) |
+ (1 << SDRC_POWER_PAGEPOLICY_SHIFT);
+ sdrc_write_reg(l, SDRC_POWER);
}
diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
index 4dcf39c2..a0a2803 100644
--- a/arch/arm/mach-omap2/serial.c
+++ b/arch/arm/mach-omap2/serial.c
@@ -6,6 +6,8 @@
* Copyright (C) 2005-2008 Nokia Corporation
* Author: Paul Mundt <paul.mundt@nokia.com>
*
+ * Major rework for PM support by Kevin Hilman
+ *
* Based off of arch/arm/mach-omap/omap1/serial.c
*
* This file is subject to the terms and conditions of the GNU General Public
@@ -21,9 +23,50 @@
#include <mach/common.h>
#include <mach/board.h>
+#include <mach/clock.h>
+#include <mach/control.h>
-static struct clk *uart_ick[OMAP_MAX_NR_PORTS];
-static struct clk *uart_fck[OMAP_MAX_NR_PORTS];
+#include "prm.h"
+#include "pm.h"
+#include "prm-regbits-34xx.h"
+
+#define UART_OMAP_WER 0x17 /* Wake-up enable register */
+
+#define DEFAULT_TIMEOUT (5 * HZ)
+
+struct omap_uart_state {
+ int num;
+ int can_sleep;
+ struct timer_list timer;
+ u32 timeout;
+
+ void __iomem *wk_st;
+ void __iomem *wk_en;
+ u32 wk_mask;
+ u32 padconf;
+
+ struct clk *ick;
+ struct clk *fck;
+ int clocked;
+
+ struct plat_serial8250_port *p;
+ struct list_head node;
+
+#if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM)
+ int context_valid;
+
+ /* Registers to be saved/restored for OFF-mode */
+ u16 dll;
+ u16 dlh;
+ u16 ier;
+ u16 sysc;
+ u16 scr;
+ u16 wer;
+#endif
+};
+
+static struct omap_uart_state omap_uart[OMAP_MAX_NR_PORTS];
+static LIST_HEAD(uart_list);
static struct plat_serial8250_port serial_platform_data[] = {
{
@@ -74,30 +117,358 @@
* properly. Note that the TX watermark initialization may not be needed
* once the 8250.c watermark handling code is merged.
*/
-static inline void __init omap_serial_reset(struct plat_serial8250_port *p)
+static inline void __init omap_uart_reset(struct omap_uart_state *uart)
{
+ struct plat_serial8250_port *p = uart->p;
+
serial_write_reg(p, UART_OMAP_MDR1, 0x07);
serial_write_reg(p, UART_OMAP_SCR, 0x08);
serial_write_reg(p, UART_OMAP_MDR1, 0x00);
serial_write_reg(p, UART_OMAP_SYSC, (0x02 << 3) | (1 << 2) | (1 << 0));
}
-void omap_serial_enable_clocks(int enable)
+#if defined(CONFIG_PM) && defined(CONFIG_ARCH_OMAP3)
+
+static int enable_off_mode; /* to be removed by full off-mode patches */
+
+static void omap_uart_save_context(struct omap_uart_state *uart)
{
- int i;
- for (i = 0; i < OMAP_MAX_NR_PORTS; i++) {
- if (uart_ick[i] && uart_fck[i]) {
- if (enable) {
- clk_enable(uart_ick[i]);
- clk_enable(uart_fck[i]);
- } else {
- clk_disable(uart_ick[i]);
- clk_disable(uart_fck[i]);
- }
+ u16 lcr = 0;
+ struct plat_serial8250_port *p = uart->p;
+
+ if (!enable_off_mode)
+ return;
+
+ lcr = serial_read_reg(p, UART_LCR);
+ serial_write_reg(p, UART_LCR, 0xBF);
+ uart->dll = serial_read_reg(p, UART_DLL);
+ uart->dlh = serial_read_reg(p, UART_DLM);
+ serial_write_reg(p, UART_LCR, lcr);
+ uart->ier = serial_read_reg(p, UART_IER);
+ uart->sysc = serial_read_reg(p, UART_OMAP_SYSC);
+ uart->scr = serial_read_reg(p, UART_OMAP_SCR);
+ uart->wer = serial_read_reg(p, UART_OMAP_WER);
+
+ uart->context_valid = 1;
+}
+
+static void omap_uart_restore_context(struct omap_uart_state *uart)
+{
+ u16 efr = 0;
+ struct plat_serial8250_port *p = uart->p;
+
+ if (!enable_off_mode)
+ return;
+
+ if (!uart->context_valid)
+ return;
+
+ uart->context_valid = 0;
+
+ serial_write_reg(p, UART_OMAP_MDR1, 0x7);
+ serial_write_reg(p, UART_LCR, 0xBF); /* Config B mode */
+ efr = serial_read_reg(p, UART_EFR);
+ serial_write_reg(p, UART_EFR, UART_EFR_ECB);
+ serial_write_reg(p, UART_LCR, 0x0); /* Operational mode */
+ serial_write_reg(p, UART_IER, 0x0);
+ serial_write_reg(p, UART_LCR, 0xBF); /* Config B mode */
+ serial_write_reg(p, UART_DLL, uart->dll);
+ serial_write_reg(p, UART_DLM, uart->dlh);
+ serial_write_reg(p, UART_LCR, 0x0); /* Operational mode */
+ serial_write_reg(p, UART_IER, uart->ier);
+ serial_write_reg(p, UART_FCR, 0xA1);
+ serial_write_reg(p, UART_LCR, 0xBF); /* Config B mode */
+ serial_write_reg(p, UART_EFR, efr);
+ serial_write_reg(p, UART_LCR, UART_LCR_WLEN8);
+ serial_write_reg(p, UART_OMAP_SCR, uart->scr);
+ serial_write_reg(p, UART_OMAP_WER, uart->wer);
+ serial_write_reg(p, UART_OMAP_SYSC, uart->sysc);
+ serial_write_reg(p, UART_OMAP_MDR1, 0x00); /* UART 16x mode */
+}
+#else
+static inline void omap_uart_save_context(struct omap_uart_state *uart) {}
+static inline void omap_uart_restore_context(struct omap_uart_state *uart) {}
+#endif /* CONFIG_PM && CONFIG_ARCH_OMAP3 */
+
+static inline void omap_uart_enable_clocks(struct omap_uart_state *uart)
+{
+ if (uart->clocked)
+ return;
+
+ clk_enable(uart->ick);
+ clk_enable(uart->fck);
+ uart->clocked = 1;
+ omap_uart_restore_context(uart);
+}
+
+#ifdef CONFIG_PM
+
+static inline void omap_uart_disable_clocks(struct omap_uart_state *uart)
+{
+ if (!uart->clocked)
+ return;
+
+ omap_uart_save_context(uart);
+ uart->clocked = 0;
+ clk_disable(uart->ick);
+ clk_disable(uart->fck);
+}
+
+static void omap_uart_smart_idle_enable(struct omap_uart_state *uart,
+ int enable)
+{
+ struct plat_serial8250_port *p = uart->p;
+ u16 sysc;
+
+ sysc = serial_read_reg(p, UART_OMAP_SYSC) & 0x7;
+ if (enable)
+ sysc |= 0x2 << 3;
+ else
+ sysc |= 0x1 << 3;
+
+ serial_write_reg(p, UART_OMAP_SYSC, sysc);
+}
+
+static void omap_uart_block_sleep(struct omap_uart_state *uart)
+{
+ omap_uart_enable_clocks(uart);
+
+ omap_uart_smart_idle_enable(uart, 0);
+ uart->can_sleep = 0;
+ if (uart->timeout)
+ mod_timer(&uart->timer, jiffies + uart->timeout);
+ else
+ del_timer(&uart->timer);
+}
+
+static void omap_uart_allow_sleep(struct omap_uart_state *uart)
+{
+ if (!uart->clocked)
+ return;
+
+ omap_uart_smart_idle_enable(uart, 1);
+ uart->can_sleep = 1;
+ del_timer(&uart->timer);
+}
+
+static void omap_uart_idle_timer(unsigned long data)
+{
+ struct omap_uart_state *uart = (struct omap_uart_state *)data;
+
+ omap_uart_allow_sleep(uart);
+}
+
+void omap_uart_prepare_idle(int num)
+{
+ struct omap_uart_state *uart;
+
+ list_for_each_entry(uart, &uart_list, node) {
+ if (num == uart->num && uart->can_sleep) {
+ omap_uart_disable_clocks(uart);
+ return;
}
}
}
+void omap_uart_resume_idle(int num)
+{
+ struct omap_uart_state *uart;
+
+ list_for_each_entry(uart, &uart_list, node) {
+ if (num == uart->num) {
+ omap_uart_enable_clocks(uart);
+
+ /* Check for IO pad wakeup */
+ if (cpu_is_omap34xx() && uart->padconf) {
+ u16 p = omap_ctrl_readw(uart->padconf);
+
+ if (p & OMAP3_PADCONF_WAKEUPEVENT0)
+ omap_uart_block_sleep(uart);
+ }
+
+ /* Check for normal UART wakeup */
+ if (__raw_readl(uart->wk_st) & uart->wk_mask)
+ omap_uart_block_sleep(uart);
+
+ return;
+ }
+ }
+}
+
+void omap_uart_prepare_suspend(void)
+{
+ struct omap_uart_state *uart;
+
+ list_for_each_entry(uart, &uart_list, node) {
+ omap_uart_allow_sleep(uart);
+ }
+}
+
+int omap_uart_can_sleep(void)
+{
+ struct omap_uart_state *uart;
+ int can_sleep = 1;
+
+ list_for_each_entry(uart, &uart_list, node) {
+ if (!uart->clocked)
+ continue;
+
+ if (!uart->can_sleep) {
+ can_sleep = 0;
+ continue;
+ }
+
+ /* This UART can now safely sleep. */
+ omap_uart_allow_sleep(uart);
+ }
+
+ return can_sleep;
+}
+
+/**
+ * omap_uart_interrupt()
+ *
+ * This handler is used only to detect that *any* UART interrupt has
+ * occurred. It does _nothing_ to handle the interrupt. Rather,
+ * any UART interrupt will trigger the inactivity timer so the
+ * UART will not idle or sleep for its timeout period.
+ *
+ **/
+static irqreturn_t omap_uart_interrupt(int irq, void *dev_id)
+{
+ struct omap_uart_state *uart = dev_id;
+
+ omap_uart_block_sleep(uart);
+
+ return IRQ_NONE;
+}
+
+static u32 sleep_timeout = DEFAULT_TIMEOUT;
+
+static void omap_uart_idle_init(struct omap_uart_state *uart)
+{
+ u32 v;
+ struct plat_serial8250_port *p = uart->p;
+ int ret;
+
+ uart->can_sleep = 0;
+ uart->timeout = sleep_timeout;
+ setup_timer(&uart->timer, omap_uart_idle_timer,
+ (unsigned long) uart);
+ mod_timer(&uart->timer, jiffies + uart->timeout);
+ omap_uart_smart_idle_enable(uart, 0);
+
+ if (cpu_is_omap34xx()) {
+ u32 mod = (uart->num == 2) ? OMAP3430_PER_MOD : CORE_MOD;
+ u32 wk_mask = 0;
+ u32 padconf = 0;
+
+ uart->wk_en = OMAP34XX_PRM_REGADDR(mod, PM_WKEN1);
+ uart->wk_st = OMAP34XX_PRM_REGADDR(mod, PM_WKST1);
+ switch (uart->num) {
+ case 0:
+ wk_mask = OMAP3430_ST_UART1_MASK;
+ padconf = 0x182;
+ break;
+ case 1:
+ wk_mask = OMAP3430_ST_UART2_MASK;
+ padconf = 0x17a;
+ break;
+ case 2:
+ wk_mask = OMAP3430_ST_UART3_MASK;
+ padconf = 0x19e;
+ break;
+ }
+ uart->wk_mask = wk_mask;
+ uart->padconf = padconf;
+ } else if (cpu_is_omap24xx()) {
+ u32 wk_mask = 0;
+
+ if (cpu_is_omap2430()) {
+ uart->wk_en = OMAP2430_PRM_REGADDR(CORE_MOD, PM_WKEN1);
+ uart->wk_st = OMAP2430_PRM_REGADDR(CORE_MOD, PM_WKST1);
+ } else if (cpu_is_omap2420()) {
+ uart->wk_en = OMAP2420_PRM_REGADDR(CORE_MOD, PM_WKEN1);
+ uart->wk_st = OMAP2420_PRM_REGADDR(CORE_MOD, PM_WKST1);
+ }
+ switch (uart->num) {
+ case 0:
+ wk_mask = OMAP24XX_ST_UART1_MASK;
+ break;
+ case 1:
+ wk_mask = OMAP24XX_ST_UART2_MASK;
+ break;
+ case 2:
+ wk_mask = OMAP24XX_ST_UART3_MASK;
+ break;
+ }
+ uart->wk_mask = wk_mask;
+ } else {
+ uart->wk_en = 0;
+ uart->wk_st = 0;
+ uart->wk_mask = 0;
+ uart->padconf = 0;
+ }
+
+ /* Set wake-enable bit */
+ if (uart->wk_en && uart->wk_mask) {
+ v = __raw_readl(uart->wk_en);
+ v |= uart->wk_mask;
+ __raw_writel(v, uart->wk_en);
+ }
+
+ /* Ensure IOPAD wake-enables are set */
+ if (cpu_is_omap34xx() && uart->padconf) {
+ u16 v;
+
+ v = omap_ctrl_readw(uart->padconf);
+ v |= OMAP3_PADCONF_WAKEUPENABLE0;
+ omap_ctrl_writew(v, uart->padconf);
+ }
+
+ p->flags |= UPF_SHARE_IRQ;
+ ret = request_irq(p->irq, omap_uart_interrupt, IRQF_SHARED,
+ "serial idle", (void *)uart);
+ WARN_ON(ret);
+}
+
+static ssize_t sleep_timeout_show(struct kobject *kobj,
+ struct kobj_attribute *attr,
+ char *buf)
+{
+ return sprintf(buf, "%u\n", sleep_timeout / HZ);
+}
+
+static ssize_t sleep_timeout_store(struct kobject *kobj,
+ struct kobj_attribute *attr,
+ const char *buf, size_t n)
+{
+ struct omap_uart_state *uart;
+ unsigned int value;
+
+ if (sscanf(buf, "%u", &value) != 1) {
+ printk(KERN_ERR "sleep_timeout_store: Invalid value\n");
+ return -EINVAL;
+ }
+ sleep_timeout = value * HZ;
+ list_for_each_entry(uart, &uart_list, node) {
+ uart->timeout = sleep_timeout;
+ if (uart->timeout)
+ mod_timer(&uart->timer, jiffies + uart->timeout);
+ else
+ /* A zero value means disable timeout feature */
+ omap_uart_block_sleep(uart);
+ }
+ return n;
+}
+
+static struct kobj_attribute sleep_timeout_attr =
+ __ATTR(sleep_timeout, 0644, sleep_timeout_show, sleep_timeout_store);
+
+#else
+static inline void omap_uart_idle_init(struct omap_uart_state *uart) {}
+#endif /* CONFIG_PM */
+
void __init omap_serial_init(void)
{
int i;
@@ -117,6 +488,7 @@
for (i = 0; i < OMAP_MAX_NR_PORTS; i++) {
struct plat_serial8250_port *p = serial_platform_data + i;
+ struct omap_uart_state *uart = &omap_uart[i];
if (!(info->enabled_uarts & (1 << i))) {
p->membase = NULL;
@@ -125,22 +497,30 @@
}
sprintf(name, "uart%d_ick", i+1);
- uart_ick[i] = clk_get(NULL, name);
- if (IS_ERR(uart_ick[i])) {
+ uart->ick = clk_get(NULL, name);
+ if (IS_ERR(uart->ick)) {
printk(KERN_ERR "Could not get uart%d_ick\n", i+1);
- uart_ick[i] = NULL;
- } else
- clk_enable(uart_ick[i]);
+ uart->ick = NULL;
+ }
sprintf(name, "uart%d_fck", i+1);
- uart_fck[i] = clk_get(NULL, name);
- if (IS_ERR(uart_fck[i])) {
+ uart->fck = clk_get(NULL, name);
+ if (IS_ERR(uart->fck)) {
printk(KERN_ERR "Could not get uart%d_fck\n", i+1);
- uart_fck[i] = NULL;
- } else
- clk_enable(uart_fck[i]);
+ uart->fck = NULL;
+ }
- omap_serial_reset(p);
+ if (!uart->ick || !uart->fck)
+ continue;
+
+ uart->num = i;
+ p->private_data = uart;
+ uart->p = p;
+ list_add(&uart->node, &uart_list);
+
+ omap_uart_enable_clocks(uart);
+ omap_uart_reset(uart);
+ omap_uart_idle_init(uart);
}
}
@@ -154,6 +534,15 @@
static int __init omap_init(void)
{
- return platform_device_register(&serial_device);
+ int ret;
+
+ ret = platform_device_register(&serial_device);
+
+#ifdef CONFIG_PM
+ if (!ret)
+ ret = sysfs_create_file(&serial_device.dev.kobj,
+ &sleep_timeout_attr.attr);
+#endif
+ return ret;
}
arch_initcall(omap_init);
diff --git a/arch/arm/mach-omap2/sleep24xx.S b/arch/arm/mach-omap2/sleep24xx.S
index bf9e961..130aadb 100644
--- a/arch/arm/mach-omap2/sleep24xx.S
+++ b/arch/arm/mach-omap2/sleep24xx.S
@@ -28,7 +28,6 @@
#include <linux/linkage.h>
#include <asm/assembler.h>
#include <mach/io.h>
-#include <mach/pm.h>
#include <mach/omap24xx.h>
diff --git a/arch/arm/mach-omap2/sleep34xx.S b/arch/arm/mach-omap2/sleep34xx.S
new file mode 100644
index 0000000..e5e2553
--- /dev/null
+++ b/arch/arm/mach-omap2/sleep34xx.S
@@ -0,0 +1,436 @@
+/*
+ * linux/arch/arm/mach-omap2/sleep.S
+ *
+ * (C) Copyright 2007
+ * Texas Instruments
+ * Karthik Dasu <karthik-dp@ti.com>
+ *
+ * (C) Copyright 2004
+ * Texas Instruments, <www.ti.com>
+ * Richard Woodruff <r-woodruff2@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+#include <mach/io.h>
+#include <mach/control.h>
+
+#include "prm.h"
+#include "sdrc.h"
+
+#define PM_PREPWSTST_CORE_V OMAP34XX_PRM_REGADDR(CORE_MOD, \
+ OMAP3430_PM_PREPWSTST)
+#define PM_PREPWSTST_MPU_V OMAP34XX_PRM_REGADDR(MPU_MOD, \
+ OMAP3430_PM_PREPWSTST)
+#define PM_PWSTCTRL_MPU_P OMAP34XX_PRM_REGADDR(MPU_MOD, PM_PWSTCTRL)
+#define SCRATCHPAD_MEM_OFFS 0x310 /* Move this as correct place is
+ * available */
+#define SCRATCHPAD_BASE_P OMAP343X_CTRL_REGADDR(\
+ OMAP343X_CONTROL_MEM_WKUP +\
+ SCRATCHPAD_MEM_OFFS)
+#define SDRC_POWER_V OMAP34XX_SDRC_REGADDR(SDRC_POWER)
+
+ .text
+/* Function call to get the restore pointer for resume from OFF */
+ENTRY(get_restore_pointer)
+ stmfd sp!, {lr} @ save registers on stack
+ adr r0, restore
+ ldmfd sp!, {pc} @ restore regs and return
+ENTRY(get_restore_pointer_sz)
+ .word . - get_restore_pointer_sz
+/*
+ * Forces OMAP into idle state
+ *
+ * omap34xx_suspend() - This bit of code just executes the WFI
+ * for normal idles.
+ *
+ * Note: This code get's copied to internal SRAM at boot. When the OMAP
+ * wakes up it continues execution at the point it went to sleep.
+ */
+ENTRY(omap34xx_cpu_suspend)
+ stmfd sp!, {r0-r12, lr} @ save registers on stack
+loop:
+ /*b loop*/ @Enable to debug by stepping through code
+ /* r0 contains restore pointer in sdram */
+ /* r1 contains information about saving context */
+ ldr r4, sdrc_power @ read the SDRC_POWER register
+ ldr r5, [r4] @ read the contents of SDRC_POWER
+ orr r5, r5, #0x40 @ enable self refresh on idle req
+ str r5, [r4] @ write back to SDRC_POWER register
+
+ cmp r1, #0x0
+ /* If context save is required, do that and execute wfi */
+ bne save_context_wfi
+ /* Data memory barrier and Data sync barrier */
+ mov r1, #0
+ mcr p15, 0, r1, c7, c10, 4
+ mcr p15, 0, r1, c7, c10, 5
+
+ wfi @ wait for interrupt
+
+ nop
+ nop
+ nop
+ nop
+ nop
+ nop
+ nop
+ nop
+ nop
+ nop
+ bl i_dll_wait
+
+ ldmfd sp!, {r0-r12, pc} @ restore regs and return
+restore:
+ /* b restore*/ @ Enable to debug restore code
+ /* Check what was the reason for mpu reset and store the reason in r9*/
+ /* 1 - Only L1 and logic lost */
+ /* 2 - Only L2 lost - In this case, we wont be here */
+ /* 3 - Both L1 and L2 lost */
+ ldr r1, pm_pwstctrl_mpu
+ ldr r2, [r1]
+ and r2, r2, #0x3
+ cmp r2, #0x0 @ Check if target power state was OFF or RET
+ moveq r9, #0x3 @ MPU OFF => L1 and L2 lost
+ movne r9, #0x1 @ Only L1 and L2 lost => avoid L2 invalidation
+ bne logic_l1_restore
+ /* Execute smi to invalidate L2 cache */
+ mov r12, #0x1 @ set up to invalide L2
+smi: .word 0xE1600070 @ Call SMI monitor (smieq)
+logic_l1_restore:
+ mov r1, #0
+ /* Invalidate all instruction caches to PoU
+ * and flush branch target cache */
+ mcr p15, 0, r1, c7, c5, 0
+
+ ldr r4, scratchpad_base
+ ldr r3, [r4,#0xBC]
+ ldmia r3!, {r4-r6}
+ mov sp, r4
+ msr spsr_cxsf, r5
+ mov lr, r6
+
+ ldmia r3!, {r4-r9}
+ /* Coprocessor access Control Register */
+ mcr p15, 0, r4, c1, c0, 2
+
+ /* TTBR0 */
+ MCR p15, 0, r5, c2, c0, 0
+ /* TTBR1 */
+ MCR p15, 0, r6, c2, c0, 1
+ /* Translation table base control register */
+ MCR p15, 0, r7, c2, c0, 2
+ /*domain access Control Register */
+ MCR p15, 0, r8, c3, c0, 0
+ /* data fault status Register */
+ MCR p15, 0, r9, c5, c0, 0
+
+ ldmia r3!,{r4-r8}
+ /* instruction fault status Register */
+ MCR p15, 0, r4, c5, c0, 1
+ /*Data Auxiliary Fault Status Register */
+ MCR p15, 0, r5, c5, c1, 0
+ /*Instruction Auxiliary Fault Status Register*/
+ MCR p15, 0, r6, c5, c1, 1
+ /*Data Fault Address Register */
+ MCR p15, 0, r7, c6, c0, 0
+ /*Instruction Fault Address Register*/
+ MCR p15, 0, r8, c6, c0, 2
+ ldmia r3!,{r4-r7}
+
+ /* user r/w thread and process ID */
+ MCR p15, 0, r4, c13, c0, 2
+ /* user ro thread and process ID */
+ MCR p15, 0, r5, c13, c0, 3
+ /*Privileged only thread and process ID */
+ MCR p15, 0, r6, c13, c0, 4
+ /* cache size selection */
+ MCR p15, 2, r7, c0, c0, 0
+ ldmia r3!,{r4-r8}
+ /* Data TLB lockdown registers */
+ MCR p15, 0, r4, c10, c0, 0
+ /* Instruction TLB lockdown registers */
+ MCR p15, 0, r5, c10, c0, 1
+ /* Secure or Nonsecure Vector Base Address */
+ MCR p15, 0, r6, c12, c0, 0
+ /* FCSE PID */
+ MCR p15, 0, r7, c13, c0, 0
+ /* Context PID */
+ MCR p15, 0, r8, c13, c0, 1
+
+ ldmia r3!,{r4-r5}
+ /* primary memory remap register */
+ MCR p15, 0, r4, c10, c2, 0
+ /*normal memory remap register */
+ MCR p15, 0, r5, c10, c2, 1
+
+ /* Restore cpsr */
+ ldmia r3!,{r4} /*load CPSR from SDRAM*/
+ msr cpsr, r4 /*store cpsr */
+
+ /* Enabling MMU here */
+ mrc p15, 0, r7, c2, c0, 2 /* Read TTBRControl */
+ /* Extract N (0:2) bits and decide whether to use TTBR0 or TTBR1*/
+ and r7, #0x7
+ cmp r7, #0x0
+ beq usettbr0
+ttbr_error:
+ /* More work needs to be done to support N[0:2] value other than 0
+ * So looping here so that the error can be detected
+ */
+ b ttbr_error
+usettbr0:
+ mrc p15, 0, r2, c2, c0, 0
+ ldr r5, ttbrbit_mask
+ and r2, r5
+ mov r4, pc
+ ldr r5, table_index_mask
+ and r4, r5 /* r4 = 31 to 20 bits of pc */
+ /* Extract the value to be written to table entry */
+ ldr r1, table_entry
+ add r1, r1, r4 /* r1 has value to be written to table entry*/
+ /* Getting the address of table entry to modify */
+ lsr r4, #18
+ add r2, r4 /* r2 has the location which needs to be modified */
+ /* Storing previous entry of location being modified */
+ ldr r5, scratchpad_base
+ ldr r4, [r2]
+ str r4, [r5, #0xC0]
+ /* Modify the table entry */
+ str r1, [r2]
+ /* Storing address of entry being modified
+ * - will be restored after enabling MMU */
+ ldr r5, scratchpad_base
+ str r2, [r5, #0xC4]
+
+ mov r0, #0
+ mcr p15, 0, r0, c7, c5, 4 @ Flush prefetch buffer
+ mcr p15, 0, r0, c7, c5, 6 @ Invalidate branch predictor array
+ mcr p15, 0, r0, c8, c5, 0 @ Invalidate instruction TLB
+ mcr p15, 0, r0, c8, c6, 0 @ Invalidate data TLB
+ /* Restore control register but dont enable caches here*/
+ /* Caches will be enabled after restoring MMU table entry */
+ ldmia r3!, {r4}
+ /* Store previous value of control register in scratchpad */
+ str r4, [r5, #0xC8]
+ ldr r2, cache_pred_disable_mask
+ and r4, r2
+ mcr p15, 0, r4, c1, c0, 0
+
+ ldmfd sp!, {r0-r12, pc} @ restore regs and return
+save_context_wfi:
+ /*b save_context_wfi*/ @ enable to debug save code
+ mov r8, r0 /* Store SDRAM address in r8 */
+ /* Check what that target sleep state is:stored in r1*/
+ /* 1 - Only L1 and logic lost */
+ /* 2 - Only L2 lost */
+ /* 3 - Both L1 and L2 lost */
+ cmp r1, #0x2 /* Only L2 lost */
+ beq clean_l2
+ cmp r1, #0x1 /* L2 retained */
+ /* r9 stores whether to clean L2 or not*/
+ moveq r9, #0x0 /* Dont Clean L2 */
+ movne r9, #0x1 /* Clean L2 */
+l1_logic_lost:
+ /* Store sp and spsr to SDRAM */
+ mov r4, sp
+ mrs r5, spsr
+ mov r6, lr
+ stmia r8!, {r4-r6}
+ /* Save all ARM registers */
+ /* Coprocessor access control register */
+ mrc p15, 0, r6, c1, c0, 2
+ stmia r8!, {r6}
+ /* TTBR0, TTBR1 and Translation table base control */
+ mrc p15, 0, r4, c2, c0, 0
+ mrc p15, 0, r5, c2, c0, 1
+ mrc p15, 0, r6, c2, c0, 2
+ stmia r8!, {r4-r6}
+ /* Domain access control register, data fault status register,
+ and instruction fault status register */
+ mrc p15, 0, r4, c3, c0, 0
+ mrc p15, 0, r5, c5, c0, 0
+ mrc p15, 0, r6, c5, c0, 1
+ stmia r8!, {r4-r6}
+ /* Data aux fault status register, instruction aux fault status,
+ datat fault address register and instruction fault address register*/
+ mrc p15, 0, r4, c5, c1, 0
+ mrc p15, 0, r5, c5, c1, 1
+ mrc p15, 0, r6, c6, c0, 0
+ mrc p15, 0, r7, c6, c0, 2
+ stmia r8!, {r4-r7}
+ /* user r/w thread and process ID, user r/o thread and process ID,
+ priv only thread and process ID, cache size selection */
+ mrc p15, 0, r4, c13, c0, 2
+ mrc p15, 0, r5, c13, c0, 3
+ mrc p15, 0, r6, c13, c0, 4
+ mrc p15, 2, r7, c0, c0, 0
+ stmia r8!, {r4-r7}
+ /* Data TLB lockdown, instruction TLB lockdown registers */
+ mrc p15, 0, r5, c10, c0, 0
+ mrc p15, 0, r6, c10, c0, 1
+ stmia r8!, {r5-r6}
+ /* Secure or non secure vector base address, FCSE PID, Context PID*/
+ mrc p15, 0, r4, c12, c0, 0
+ mrc p15, 0, r5, c13, c0, 0
+ mrc p15, 0, r6, c13, c0, 1
+ stmia r8!, {r4-r6}
+ /* Primary remap, normal remap registers */
+ mrc p15, 0, r4, c10, c2, 0
+ mrc p15, 0, r5, c10, c2, 1
+ stmia r8!,{r4-r5}
+
+ /* Store current cpsr*/
+ mrs r2, cpsr
+ stmia r8!, {r2}
+
+ mrc p15, 0, r4, c1, c0, 0
+ /* save control register */
+ stmia r8!, {r4}
+clean_caches:
+ /* Clean Data or unified cache to POU*/
+ /* How to invalidate only L1 cache???? - #FIX_ME# */
+ /* mcr p15, 0, r11, c7, c11, 1 */
+ cmp r9, #1 /* Check whether L2 inval is required or not*/
+ bne skip_l2_inval
+clean_l2:
+ /* read clidr */
+ mrc p15, 1, r0, c0, c0, 1
+ /* extract loc from clidr */
+ ands r3, r0, #0x7000000
+ /* left align loc bit field */
+ mov r3, r3, lsr #23
+ /* if loc is 0, then no need to clean */
+ beq finished
+ /* start clean at cache level 0 */
+ mov r10, #0
+loop1:
+ /* work out 3x current cache level */
+ add r2, r10, r10, lsr #1
+ /* extract cache type bits from clidr*/
+ mov r1, r0, lsr r2
+ /* mask of the bits for current cache only */
+ and r1, r1, #7
+ /* see what cache we have at this level */
+ cmp r1, #2
+ /* skip if no cache, or just i-cache */
+ blt skip
+ /* select current cache level in cssr */
+ mcr p15, 2, r10, c0, c0, 0
+ /* isb to sych the new cssr&csidr */
+ isb
+ /* read the new csidr */
+ mrc p15, 1, r1, c0, c0, 0
+ /* extract the length of the cache lines */
+ and r2, r1, #7
+ /* add 4 (line length offset) */
+ add r2, r2, #4
+ ldr r4, assoc_mask
+ /* find maximum number on the way size */
+ ands r4, r4, r1, lsr #3
+ /* find bit position of way size increment */
+ clz r5, r4
+ ldr r7, numset_mask
+ /* extract max number of the index size*/
+ ands r7, r7, r1, lsr #13
+loop2:
+ mov r9, r4
+ /* create working copy of max way size*/
+loop3:
+ /* factor way and cache number into r11 */
+ orr r11, r10, r9, lsl r5
+ /* factor index number into r11 */
+ orr r11, r11, r7, lsl r2
+ /*clean & invalidate by set/way */
+ mcr p15, 0, r11, c7, c10, 2
+ /* decrement the way*/
+ subs r9, r9, #1
+ bge loop3
+ /*decrement the index */
+ subs r7, r7, #1
+ bge loop2
+skip:
+ add r10, r10, #2
+ /* increment cache number */
+ cmp r3, r10
+ bgt loop1
+finished:
+ /*swith back to cache level 0 */
+ mov r10, #0
+ /* select current cache level in cssr */
+ mcr p15, 2, r10, c0, c0, 0
+ isb
+skip_l2_inval:
+ /* Data memory barrier and Data sync barrier */
+ mov r1, #0
+ mcr p15, 0, r1, c7, c10, 4
+ mcr p15, 0, r1, c7, c10, 5
+
+ wfi @ wait for interrupt
+ nop
+ nop
+ nop
+ nop
+ nop
+ nop
+ nop
+ nop
+ nop
+ nop
+ bl i_dll_wait
+ /* restore regs and return */
+ ldmfd sp!, {r0-r12, pc}
+
+i_dll_wait:
+ ldr r4, clk_stabilize_delay
+
+i_dll_delay:
+ subs r4, r4, #0x1
+ bne i_dll_delay
+ ldr r4, sdrc_power
+ ldr r5, [r4]
+ bic r5, r5, #0x40
+ str r5, [r4]
+ bx lr
+pm_prepwstst_core:
+ .word PM_PREPWSTST_CORE_V
+pm_prepwstst_mpu:
+ .word PM_PREPWSTST_MPU_V
+pm_pwstctrl_mpu:
+ .word PM_PWSTCTRL_MPU_P
+scratchpad_base:
+ .word SCRATCHPAD_BASE_P
+sdrc_power:
+ .word SDRC_POWER_V
+context_mem:
+ .word 0x803E3E14
+clk_stabilize_delay:
+ .word 0x000001FF
+assoc_mask:
+ .word 0x3ff
+numset_mask:
+ .word 0x7fff
+ttbrbit_mask:
+ .word 0xFFFFC000
+table_index_mask:
+ .word 0xFFF00000
+table_entry:
+ .word 0x00000C02
+cache_pred_disable_mask:
+ .word 0xFFFFE7FB
+ENTRY(omap34xx_cpu_suspend_sz)
+ .word . - omap34xx_cpu_suspend
diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S
index 2c71461..c080c825 100644
--- a/arch/arm/mach-omap2/sram34xx.S
+++ b/arch/arm/mach-omap2/sram34xx.S
@@ -40,69 +40,74 @@
/*
* Change frequency of core dpll
* r0 = sdrc_rfr_ctrl r1 = sdrc_actim_ctrla r2 = sdrc_actim_ctrlb r3 = M2
+ * r4 = Unlock SDRC DLL? (1 = yes, 0 = no) -- only unlock DLL for
+ * SDRC rates < 83MHz
*/
ENTRY(omap3_sram_configure_core_dpll)
stmfd sp!, {r1-r12, lr} @ store regs to stack
+ ldr r4, [sp, #52] @ pull extra args off the stack
+ dsb @ flush buffered writes to interconnect
cmp r3, #0x2
blne configure_sdrc
- cmp r3, #0x2
+ cmp r4, #0x1
+ bleq unlock_dll
blne lock_dll
- cmp r3, #0x1
- blne unlock_dll
bl sdram_in_selfrefresh @ put the SDRAM in self refresh
bl configure_core_dpll
bl enable_sdrc
- cmp r3, #0x1
- blne wait_dll_unlock
- cmp r3, #0x2
+ cmp r4, #0x1
+ bleq wait_dll_unlock
blne wait_dll_lock
cmp r3, #0x1
blne configure_sdrc
+ isb @ prevent speculative exec past here
mov r0, #0 @ return value
ldmfd sp!, {r1-r12, pc} @ restore regs and return
unlock_dll:
- ldr r4, omap3_sdrc_dlla_ctrl
- ldr r5, [r4]
- orr r5, r5, #0x4
- str r5, [r4]
+ ldr r11, omap3_sdrc_dlla_ctrl
+ ldr r12, [r11]
+ orr r12, r12, #0x4
+ str r12, [r11] @ (no OCP barrier needed)
bx lr
lock_dll:
- ldr r4, omap3_sdrc_dlla_ctrl
- ldr r5, [r4]
- bic r5, r5, #0x4
- str r5, [r4]
+ ldr r11, omap3_sdrc_dlla_ctrl
+ ldr r12, [r11]
+ bic r12, r12, #0x4
+ str r12, [r11] @ (no OCP barrier needed)
bx lr
sdram_in_selfrefresh:
- mov r5, #0x0 @ Move 0 to R5
- mcr p15, 0, r5, c7, c10, 5 @ memory barrier
- ldr r4, omap3_sdrc_power @ read the SDRC_POWER register
- ldr r5, [r4] @ read the contents of SDRC_POWER
- orr r5, r5, #0x40 @ enable self refresh on idle req
- str r5, [r4] @ write back to SDRC_POWER register
- ldr r4, omap3_cm_iclken1_core @ read the CM_ICLKEN1_CORE reg
- ldr r5, [r4]
- bic r5, r5, #0x2 @ disable iclk bit for SRDC
- str r5, [r4]
+ ldr r11, omap3_sdrc_power @ read the SDRC_POWER register
+ ldr r12, [r11] @ read the contents of SDRC_POWER
+ mov r9, r12 @ keep a copy of SDRC_POWER bits
+ orr r12, r12, #0x40 @ enable self refresh on idle req
+ bic r12, r12, #0x4 @ clear PWDENA
+ str r12, [r11] @ write back to SDRC_POWER register
+ ldr r12, [r11] @ posted-write barrier for SDRC
+ ldr r11, omap3_cm_iclken1_core @ read the CM_ICLKEN1_CORE reg
+ ldr r12, [r11]
+ bic r12, r12, #0x2 @ disable iclk bit for SDRC
+ str r12, [r11]
wait_sdrc_idle:
- ldr r4, omap3_cm_idlest1_core
- ldr r5, [r4]
- and r5, r5, #0x2 @ check for SDRC idle
- cmp r5, #2
+ ldr r11, omap3_cm_idlest1_core
+ ldr r12, [r11]
+ and r12, r12, #0x2 @ check for SDRC idle
+ cmp r12, #2
bne wait_sdrc_idle
bx lr
configure_core_dpll:
- ldr r4, omap3_cm_clksel1_pll
- ldr r5, [r4]
- ldr r6, core_m2_mask_val @ modify m2 for core dpll
- and r5, r5, r6
- orr r5, r5, r3, lsl #0x1B @ r3 contains the M2 val
- str r5, [r4]
- mov r5, #0x800 @ wait for the clock to stabilise
+ ldr r11, omap3_cm_clksel1_pll
+ ldr r12, [r11]
+ ldr r10, core_m2_mask_val @ modify m2 for core dpll
+ and r12, r12, r10
+ orr r12, r12, r3, lsl #0x1B @ r3 contains the M2 val
+ str r12, [r11]
+ ldr r12, [r11] @ posted-write barrier for CM
+ mov r12, #0x800 @ wait for the clock to stabilise
cmp r3, #2
bne wait_clk_stable
bx lr
wait_clk_stable:
- subs r5, r5, #1
+ subs r12, r12, #1
bne wait_clk_stable
nop
nop
@@ -116,42 +121,42 @@
nop
bx lr
enable_sdrc:
- ldr r4, omap3_cm_iclken1_core
- ldr r5, [r4]
- orr r5, r5, #0x2 @ enable iclk bit for SDRC
- str r5, [r4]
+ ldr r11, omap3_cm_iclken1_core
+ ldr r12, [r11]
+ orr r12, r12, #0x2 @ enable iclk bit for SDRC
+ str r12, [r11]
wait_sdrc_idle1:
- ldr r4, omap3_cm_idlest1_core
- ldr r5, [r4]
- and r5, r5, #0x2
- cmp r5, #0
+ ldr r11, omap3_cm_idlest1_core
+ ldr r12, [r11]
+ and r12, r12, #0x2
+ cmp r12, #0
bne wait_sdrc_idle1
- ldr r4, omap3_sdrc_power
- ldr r5, [r4]
- bic r5, r5, #0x40
- str r5, [r4]
+restore_sdrc_power_val:
+ ldr r11, omap3_sdrc_power
+ str r9, [r11] @ restore SDRC_POWER, no barrier needed
bx lr
wait_dll_lock:
- ldr r4, omap3_sdrc_dlla_status
- ldr r5, [r4]
- and r5, r5, #0x4
- cmp r5, #0x4
+ ldr r11, omap3_sdrc_dlla_status
+ ldr r12, [r11]
+ and r12, r12, #0x4
+ cmp r12, #0x4
bne wait_dll_lock
bx lr
wait_dll_unlock:
- ldr r4, omap3_sdrc_dlla_status
- ldr r5, [r4]
- and r5, r5, #0x4
- cmp r5, #0x0
+ ldr r11, omap3_sdrc_dlla_status
+ ldr r12, [r11]
+ and r12, r12, #0x4
+ cmp r12, #0x0
bne wait_dll_unlock
bx lr
configure_sdrc:
- ldr r4, omap3_sdrc_rfr_ctrl
- str r0, [r4]
- ldr r4, omap3_sdrc_actim_ctrla
- str r1, [r4]
- ldr r4, omap3_sdrc_actim_ctrlb
- str r2, [r4]
+ ldr r11, omap3_sdrc_rfr_ctrl
+ str r0, [r11]
+ ldr r11, omap3_sdrc_actim_ctrla
+ str r1, [r11]
+ ldr r11, omap3_sdrc_actim_ctrlb
+ str r2, [r11]
+ ldr r2, [r11] @ posted-write barrier for SDRC
bx lr
omap3_sdrc_power:
diff --git a/arch/arm/mach-omap2/usb-musb.c b/arch/arm/mach-omap2/usb-musb.c
index 34a56a1..d85296d 100644
--- a/arch/arm/mach-omap2/usb-musb.c
+++ b/arch/arm/mach-omap2/usb-musb.c
@@ -28,10 +28,20 @@
#include <mach/hardware.h>
#include <mach/irqs.h>
-#include <mach/pm.h>
#include <mach/mux.h>
#include <mach/usb.h>
+#define OTG_SYSCONFIG (OMAP34XX_HSUSB_OTG_BASE + 0x404)
+
+static void __init usb_musb_pm_init(void)
+{
+ /* Ensure force-idle mode for OTG controller */
+ if (cpu_is_omap34xx())
+ omap_writel(0, OTG_SYSCONFIG);
+}
+
+#ifdef CONFIG_USB_MUSB_SOC
+
static struct resource musb_resources[] = {
[0] = { /* start and end set dynamically */
.flags = IORESOURCE_MEM,
@@ -184,4 +194,13 @@
printk(KERN_ERR "Unable to register HS-USB (MUSB) device\n");
return;
}
+
+ usb_musb_pm_init();
}
+
+#else
+void __init usb_musb_init(void)
+{
+ usb_musb_pm_init();
+}
+#endif /* CONFIG_USB_MUSB_SOC */
diff --git a/arch/arm/plat-omap/Kconfig b/arch/arm/plat-omap/Kconfig
index 9dd68fa..4bc9ed7 100644
--- a/arch/arm/plat-omap/Kconfig
+++ b/arch/arm/plat-omap/Kconfig
@@ -171,7 +171,7 @@
config OMAP_SERIAL_WAKE
bool "Enable wake-up events for serial ports"
- depends on OMAP_MUX
+ depends on ARCH_OMAP1 && OMAP_MUX
default y
help
Select this option if you want to have your system wake up
diff --git a/arch/arm/plat-omap/clock.c b/arch/arm/plat-omap/clock.c
index 29efc27..508c96a 100644
--- a/arch/arm/plat-omap/clock.c
+++ b/arch/arm/plat-omap/clock.c
@@ -240,13 +240,13 @@
}
/**
- * clk_init_one - initialize any fields in the struct clk before clk init
+ * clk_preinit - initialize any fields in the struct clk before clk init
* @clk: struct clk * to initialize
*
* Initialize any struct clk fields needed before normal clk initialization
* can run. No return value.
*/
-void clk_init_one(struct clk *clk)
+void clk_preinit(struct clk *clk)
{
INIT_LIST_HEAD(&clk->children);
}
diff --git a/arch/arm/plat-omap/common.c b/arch/arm/plat-omap/common.c
index 70b68ef..86ee23d 100644
--- a/arch/arm/plat-omap/common.c
+++ b/arch/arm/plat-omap/common.c
@@ -11,7 +11,6 @@
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/delay.h>
-#include <linux/pm.h>
#include <linux/console.h>
#include <linux/serial.h>
#include <linux/tty.h>
diff --git a/arch/arm/plat-omap/include/mach/clock.h b/arch/arm/plat-omap/include/mach/clock.h
index 073a2c5..d7bd19c 100644
--- a/arch/arm/plat-omap/include/mach/clock.h
+++ b/arch/arm/plat-omap/include/mach/clock.h
@@ -119,7 +119,7 @@
extern unsigned int mpurate;
extern int clk_init(struct clk_functions *custom_clocks);
-extern void clk_init_one(struct clk *clk);
+extern void clk_preinit(struct clk *clk);
extern int clk_register(struct clk *clk);
extern void clk_reparent(struct clk *child, struct clk *parent);
extern void clk_unregister(struct clk *clk);
diff --git a/arch/arm/plat-omap/include/mach/common.h b/arch/arm/plat-omap/include/mach/common.h
index 0ecf36d..834f0b3 100644
--- a/arch/arm/plat-omap/include/mach/common.h
+++ b/arch/arm/plat-omap/include/mach/common.h
@@ -33,8 +33,6 @@
extern void omap_map_common_io(void);
extern struct sys_timer omap_timer;
-extern void omap_serial_init(void);
-extern void omap_serial_enable_clocks(int enable);
#if defined(CONFIG_I2C_OMAP) || defined(CONFIG_I2C_OMAP_MODULE)
extern int omap_register_i2c_bus(int bus_id, u32 clkrate,
struct i2c_board_info const *info,
diff --git a/arch/arm/plat-omap/include/mach/control.h b/arch/arm/plat-omap/include/mach/control.h
index 269147f..fcc5a9b 100644
--- a/arch/arm/plat-omap/include/mach/control.h
+++ b/arch/arm/plat-omap/include/mach/control.h
@@ -144,6 +144,10 @@
#define OMAP343X_CONTROL_PBIAS_LITE (OMAP2_CONTROL_GENERAL + 0x02b0)
#define OMAP343X_CONTROL_TEMP_SENSOR (OMAP2_CONTROL_GENERAL + 0x02b4)
+/* 34xx D2D idle-related pins, handled by PM core */
+#define OMAP3_PADCONF_SAD2D_MSTANDBY 0x250
+#define OMAP3_PADCONF_SAD2D_IDLEACK 0x254
+
/*
* REVISIT: This list of registers is not comprehensive - there are more
* that should be added.
@@ -189,6 +193,15 @@
#define OMAP2_PBIASLITEPWRDNZ0 (1 << 1)
#define OMAP2_PBIASLITEVMODE0 (1 << 0)
+/* CONTROL_IVA2_BOOTMOD bits */
+#define OMAP3_IVA2_BOOTMOD_SHIFT 0
+#define OMAP3_IVA2_BOOTMOD_MASK (0xf << 0)
+#define OMAP3_IVA2_BOOTMOD_IDLE (0x1 << 0)
+
+/* CONTROL_PADCONF_X bits */
+#define OMAP3_PADCONF_WAKEUPEVENT0 (1 << 15)
+#define OMAP3_PADCONF_WAKEUPENABLE0 (1 << 14)
+
#ifndef __ASSEMBLY__
#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
extern void __iomem *omap_ctrl_base_get(void);
diff --git a/arch/arm/plat-omap/include/mach/irqs.h b/arch/arm/plat-omap/include/mach/irqs.h
index 7f57ee6..f5f7c92 100644
--- a/arch/arm/plat-omap/include/mach/irqs.h
+++ b/arch/arm/plat-omap/include/mach/irqs.h
@@ -467,6 +467,7 @@
#ifndef __ASSEMBLY__
extern void omap_init_irq(void);
+extern int omap_irq_pending(void);
#endif
#include <mach/hardware.h>
diff --git a/arch/arm/plat-omap/include/mach/serial.h b/arch/arm/plat-omap/include/mach/serial.h
index 8a676a0..8e89585 100644
--- a/arch/arm/plat-omap/include/mach/serial.h
+++ b/arch/arm/plat-omap/include/mach/serial.h
@@ -40,4 +40,13 @@
__ret; \
})
+#ifndef __ASSEMBLER__
+extern void omap_serial_init(void);
+extern int omap_uart_can_sleep(void);
+extern void omap_uart_check_wakeup(void);
+extern void omap_uart_prepare_suspend(void);
+extern void omap_uart_prepare_idle(int num);
+extern void omap_uart_resume_idle(int num);
+#endif
+
#endif
diff --git a/arch/arm/plat-omap/include/mach/sram.h b/arch/arm/plat-omap/include/mach/sram.h
index ab35d62..dca7c16 100644
--- a/arch/arm/plat-omap/include/mach/sram.h
+++ b/arch/arm/plat-omap/include/mach/sram.h
@@ -23,7 +23,8 @@
extern u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl,
u32 sdrc_actim_ctrla,
- u32 sdrc_actim_ctrlb, u32 m2);
+ u32 sdrc_actim_ctrlb, u32 m2,
+ u32 unlock_dll);
/* Do not use these */
extern void omap1_sram_reprogram_clock(u32 ckctl, u32 dpllctl);
@@ -60,7 +61,8 @@
extern u32 omap3_sram_configure_core_dpll(u32 sdrc_rfr_ctrl,
u32 sdrc_actim_ctrla,
- u32 sdrc_actim_ctrlb, u32 m2);
+ u32 sdrc_actim_ctrlb, u32 m2,
+ u32 unlock_dll);
extern unsigned long omap3_sram_configure_core_dpll_sz;
#endif
diff --git a/arch/arm/plat-omap/include/mach/usb.h b/arch/arm/plat-omap/include/mach/usb.h
index 69f0cee..f337e17 100644
--- a/arch/arm/plat-omap/include/mach/usb.h
+++ b/arch/arm/plat-omap/include/mach/usb.h
@@ -27,13 +27,7 @@
#define UDC_BASE OMAP2_UDC_BASE
#define OMAP_OHCI_BASE OMAP2_OHCI_BASE
-#ifdef CONFIG_USB_MUSB_SOC
extern void usb_musb_init(void);
-#else
-static inline void usb_musb_init(void)
-{
-}
-#endif
#endif
diff --git a/arch/arm/plat-omap/sram.c b/arch/arm/plat-omap/sram.c
index 102c9f7..bd44d1a 100644
--- a/arch/arm/plat-omap/sram.c
+++ b/arch/arm/plat-omap/sram.c
@@ -201,6 +201,15 @@
base = OMAP3_SRAM_PA;
base = ROUND_DOWN(base, PAGE_SIZE);
omap_sram_io_desc[0].pfn = __phys_to_pfn(base);
+
+ /*
+ * SRAM must be marked as non-cached on OMAP3 since the
+ * CORE DPLL M2 divider change code (in SRAM) runs with the
+ * SDRAM controller disabled, and if it is marked cached,
+ * the ARM may attempt to write cache lines back to SDRAM
+ * which will cause the system to hang.
+ */
+ omap_sram_io_desc[0].type = MT_MEMORY_NONCACHED;
}
omap_sram_io_desc[0].length = 1024 * 1024; /* Use section desc */
@@ -343,14 +352,15 @@
static u32 (*_omap3_sram_configure_core_dpll)(u32 sdrc_rfr_ctrl,
u32 sdrc_actim_ctrla,
u32 sdrc_actim_ctrlb,
- u32 m2);
+ u32 m2, u32 unlock_dll);
u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl, u32 sdrc_actim_ctrla,
- u32 sdrc_actim_ctrlb, u32 m2)
+ u32 sdrc_actim_ctrlb, u32 m2, u32 unlock_dll)
{
BUG_ON(!_omap3_sram_configure_core_dpll);
return _omap3_sram_configure_core_dpll(sdrc_rfr_ctrl,
sdrc_actim_ctrla,
- sdrc_actim_ctrlb, m2);
+ sdrc_actim_ctrlb, m2,
+ unlock_dll);
}
/* REVISIT: Should this be same as omap34xx_sram_init() after off-idle? */
diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c
index f2e9de1..6391e3d 100644
--- a/drivers/mtd/onenand/omap2.c
+++ b/drivers/mtd/onenand/omap2.c
@@ -39,7 +39,6 @@
#include <mach/gpmc.h>
#include <mach/onenand.h>
#include <mach/gpio.h>
-#include <mach/pm.h>
#include <mach/dma.h>