[ARM] 4757/1: [AT91] UART initialization
Modify the UART initialization to allow the board-initialization code
to specify which pins are connected, and which pins should therefore
be initialized.
The current at91_init_serial() will continue to work as-is, but is
marked as "deprecated" and will be removed once the board-specific
files has been updated to use the new interface.
As in the AVR32 code, we assume that the TX and RX pins will always be
initialized.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c
index a264726..2396622 100644
--- a/arch/arm/mach-at91/at91rm9200_devices.c
+++ b/arch/arm/mach-at91/at91rm9200_devices.c
@@ -884,17 +884,21 @@
.num_resources = ARRAY_SIZE(uart0_resources),
};
-static inline void configure_usart0_pins(void)
+static inline void configure_usart0_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PA17, 1); /* TXD0 */
at91_set_A_periph(AT91_PIN_PA18, 0); /* RXD0 */
- at91_set_A_periph(AT91_PIN_PA20, 0); /* CTS0 */
- /*
- * AT91RM9200 Errata #39 - RTS0 is not internally connected to PA21.
- * We need to drive the pin manually. Default is off (RTS is active low).
- */
- at91_set_gpio_output(AT91_PIN_PA21, 1);
+ if (pins & ATMEL_UART_CTS)
+ at91_set_A_periph(AT91_PIN_PA20, 0); /* CTS0 */
+
+ if (pins & ATMEL_UART_RTS) {
+ /*
+ * AT91RM9200 Errata #39 - RTS0 is not internally connected to PA21.
+ * We need to drive the pin manually. Default is off (RTS is active low).
+ */
+ at91_set_gpio_output(AT91_PIN_PA21, 1);
+ }
}
static struct resource uart1_resources[] = {
@@ -929,16 +933,23 @@
.num_resources = ARRAY_SIZE(uart1_resources),
};
-static inline void configure_usart1_pins(void)
+static inline void configure_usart1_pins(unsigned pins)
{
- at91_set_A_periph(AT91_PIN_PB18, 0); /* RI1 */
- at91_set_A_periph(AT91_PIN_PB19, 0); /* DTR1 */
at91_set_A_periph(AT91_PIN_PB20, 1); /* TXD1 */
at91_set_A_periph(AT91_PIN_PB21, 0); /* RXD1 */
- at91_set_A_periph(AT91_PIN_PB23, 0); /* DCD1 */
- at91_set_A_periph(AT91_PIN_PB24, 0); /* CTS1 */
- at91_set_A_periph(AT91_PIN_PB25, 0); /* DSR1 */
- at91_set_A_periph(AT91_PIN_PB26, 0); /* RTS1 */
+
+ if (pins & ATMEL_UART_RI)
+ at91_set_A_periph(AT91_PIN_PB18, 0); /* RI1 */
+ if (pins & ATMEL_UART_DTR)
+ at91_set_A_periph(AT91_PIN_PB19, 0); /* DTR1 */
+ if (pins & ATMEL_UART_DCD)
+ at91_set_A_periph(AT91_PIN_PB23, 0); /* DCD1 */
+ if (pins & ATMEL_UART_CTS)
+ at91_set_A_periph(AT91_PIN_PB24, 0); /* CTS1 */
+ if (pins & ATMEL_UART_DSR)
+ at91_set_A_periph(AT91_PIN_PB25, 0); /* DSR1 */
+ if (pins & ATMEL_UART_RTS)
+ at91_set_A_periph(AT91_PIN_PB26, 0); /* RTS1 */
}
static struct resource uart2_resources[] = {
@@ -973,10 +984,15 @@
.num_resources = ARRAY_SIZE(uart2_resources),
};
-static inline void configure_usart2_pins(void)
+static inline void configure_usart2_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PA22, 0); /* RXD2 */
at91_set_A_periph(AT91_PIN_PA23, 1); /* TXD2 */
+
+ if (pins & ATMEL_UART_CTS)
+ at91_set_B_periph(AT91_PIN_PA30, 0); /* CTS2 */
+ if (pins & ATMEL_UART_RTS)
+ at91_set_B_periph(AT91_PIN_PA31, 0); /* RTS2 */
}
static struct resource uart3_resources[] = {
@@ -1011,16 +1027,21 @@
.num_resources = ARRAY_SIZE(uart3_resources),
};
-static inline void configure_usart3_pins(void)
+static inline void configure_usart3_pins(unsigned pins)
{
at91_set_B_periph(AT91_PIN_PA5, 1); /* TXD3 */
at91_set_B_periph(AT91_PIN_PA6, 0); /* RXD3 */
+
+ if (pins & ATMEL_UART_CTS)
+ at91_set_B_periph(AT91_PIN_PB1, 0); /* CTS3 */
+ if (pins & ATMEL_UART_RTS)
+ at91_set_B_periph(AT91_PIN_PB0, 0); /* RTS3 */
}
static struct platform_device *at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */
struct platform_device *atmel_default_console_device; /* the serial console device */
-void __init at91_init_serial(struct at91_uart_config *config)
+void __init __deprecated at91_init_serial(struct at91_uart_config *config)
{
int i;
@@ -1028,22 +1049,22 @@
for (i = 0; i < config->nr_tty; i++) {
switch (config->tty_map[i]) {
case 0:
- configure_usart0_pins();
+ configure_usart0_pins(ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_uarts[i] = &at91rm9200_uart0_device;
at91_clock_associate("usart0_clk", &at91rm9200_uart0_device.dev, "usart");
break;
case 1:
- configure_usart1_pins();
+ configure_usart1_pins(ATMEL_UART_CTS | ATMEL_UART_RTS | ATMEL_UART_DSR | ATMEL_UART_DTR | ATMEL_UART_DCD | ATMEL_UART_RI);
at91_uarts[i] = &at91rm9200_uart1_device;
at91_clock_associate("usart1_clk", &at91rm9200_uart1_device.dev, "usart");
break;
case 2:
- configure_usart2_pins();
+ configure_usart2_pins(0);
at91_uarts[i] = &at91rm9200_uart2_device;
at91_clock_associate("usart2_clk", &at91rm9200_uart2_device.dev, "usart");
break;
case 3:
- configure_usart3_pins();
+ configure_usart3_pins(0);
at91_uarts[i] = &at91rm9200_uart3_device;
at91_clock_associate("usart3_clk", &at91rm9200_uart3_device.dev, "usart");
break;
@@ -1065,6 +1086,53 @@
printk(KERN_INFO "AT91: No default serial console defined.\n");
}
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
+{
+ struct platform_device *pdev;
+
+ switch (id) {
+ case 0: /* DBGU */
+ pdev = &at91rm9200_dbgu_device;
+ configure_dbgu_pins();
+ at91_clock_associate("mck", &pdev->dev, "usart");
+ break;
+ case AT91RM9200_ID_US0:
+ pdev = &at91rm9200_uart0_device;
+ configure_usart0_pins(pins);
+ at91_clock_associate("usart0_clk", &pdev->dev, "usart");
+ break;
+ case AT91RM9200_ID_US1:
+ pdev = &at91rm9200_uart1_device;
+ configure_usart1_pins(pins);
+ at91_clock_associate("usart1_clk", &pdev->dev, "usart");
+ break;
+ case AT91RM9200_ID_US2:
+ pdev = &at91rm9200_uart2_device;
+ configure_usart2_pins(pins);
+ at91_clock_associate("usart2_clk", &pdev->dev, "usart");
+ break;
+ case AT91RM9200_ID_US3:
+ pdev = &at91rm9200_uart3_device;
+ configure_usart3_pins(pins);
+ at91_clock_associate("usart3_clk", &pdev->dev, "usart");
+ break;
+ default:
+ return;
+ }
+ pdev->id = portnr; /* update to mapped ID */
+
+ if (portnr < ATMEL_MAX_UART)
+ at91_uarts[portnr] = pdev;
+}
+
+void __init at91_set_serial_console(unsigned portnr)
+{
+ if (portnr < ATMEL_MAX_UART)
+ atmel_default_console_device = at91_uarts[portnr];
+ if (!atmel_default_console_device)
+ printk(KERN_INFO "AT91: No default serial console defined.\n");
+}
+
void __init at91_add_device_serial(void)
{
int i;
@@ -1075,7 +1143,9 @@
}
}
#else
-void __init at91_init_serial(struct at91_uart_config *config) {}
+void __init __deprecated at91_init_serial(struct at91_uart_config *config) {}
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
+void __init at91_set_serial_console(unsigned portnr) {}
void __init at91_add_device_serial(void) {}
#endif
diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c
index 8acd62b..5dd06bd 100644
--- a/arch/arm/mach-at91/at91sam9260_devices.c
+++ b/arch/arm/mach-at91/at91sam9260_devices.c
@@ -760,16 +760,23 @@
.num_resources = ARRAY_SIZE(uart0_resources),
};
-static inline void configure_usart0_pins(void)
+static inline void configure_usart0_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PB4, 1); /* TXD0 */
at91_set_A_periph(AT91_PIN_PB5, 0); /* RXD0 */
- at91_set_A_periph(AT91_PIN_PB26, 0); /* RTS0 */
- at91_set_A_periph(AT91_PIN_PB27, 0); /* CTS0 */
- at91_set_A_periph(AT91_PIN_PB24, 0); /* DTR0 */
- at91_set_A_periph(AT91_PIN_PB22, 0); /* DSR0 */
- at91_set_A_periph(AT91_PIN_PB23, 0); /* DCD0 */
- at91_set_A_periph(AT91_PIN_PB25, 0); /* RI0 */
+
+ if (pins & ATMEL_UART_RTS)
+ at91_set_A_periph(AT91_PIN_PB26, 0); /* RTS0 */
+ if (pins & ATMEL_UART_CTS)
+ at91_set_A_periph(AT91_PIN_PB27, 0); /* CTS0 */
+ if (pins & ATMEL_UART_DTR)
+ at91_set_A_periph(AT91_PIN_PB24, 0); /* DTR0 */
+ if (pins & ATMEL_UART_DSR)
+ at91_set_A_periph(AT91_PIN_PB22, 0); /* DSR0 */
+ if (pins & ATMEL_UART_DCD)
+ at91_set_A_periph(AT91_PIN_PB23, 0); /* DCD0 */
+ if (pins & ATMEL_UART_RI)
+ at91_set_A_periph(AT91_PIN_PB25, 0); /* RI0 */
}
static struct resource uart1_resources[] = {
@@ -804,12 +811,15 @@
.num_resources = ARRAY_SIZE(uart1_resources),
};
-static inline void configure_usart1_pins(void)
+static inline void configure_usart1_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PB6, 1); /* TXD1 */
at91_set_A_periph(AT91_PIN_PB7, 0); /* RXD1 */
- at91_set_A_periph(AT91_PIN_PB28, 0); /* RTS1 */
- at91_set_A_periph(AT91_PIN_PB29, 0); /* CTS1 */
+
+ if (pins & ATMEL_UART_RTS)
+ at91_set_A_periph(AT91_PIN_PB28, 0); /* RTS1 */
+ if (pins & ATMEL_UART_CTS)
+ at91_set_A_periph(AT91_PIN_PB29, 0); /* CTS1 */
}
static struct resource uart2_resources[] = {
@@ -844,10 +854,15 @@
.num_resources = ARRAY_SIZE(uart2_resources),
};
-static inline void configure_usart2_pins(void)
+static inline void configure_usart2_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PB8, 1); /* TXD2 */
at91_set_A_periph(AT91_PIN_PB9, 0); /* RXD2 */
+
+ if (pins & ATMEL_UART_RTS)
+ at91_set_A_periph(AT91_PIN_PA4, 0); /* RTS2 */
+ if (pins & ATMEL_UART_CTS)
+ at91_set_A_periph(AT91_PIN_PA5, 0); /* CTS2 */
}
static struct resource uart3_resources[] = {
@@ -882,10 +897,15 @@
.num_resources = ARRAY_SIZE(uart3_resources),
};
-static inline void configure_usart3_pins(void)
+static inline void configure_usart3_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PB10, 1); /* TXD3 */
at91_set_A_periph(AT91_PIN_PB11, 0); /* RXD3 */
+
+ if (pins & ATMEL_UART_RTS)
+ at91_set_B_periph(AT91_PIN_PC8, 0); /* RTS3 */
+ if (pins & ATMEL_UART_CTS)
+ at91_set_B_periph(AT91_PIN_PC10, 0); /* CTS3 */
}
static struct resource uart4_resources[] = {
@@ -967,7 +987,7 @@
static struct platform_device *at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */
struct platform_device *atmel_default_console_device; /* the serial console device */
-void __init at91_init_serial(struct at91_uart_config *config)
+void __init __deprecated at91_init_serial(struct at91_uart_config *config)
{
int i;
@@ -975,22 +995,22 @@
for (i = 0; i < config->nr_tty; i++) {
switch (config->tty_map[i]) {
case 0:
- configure_usart0_pins();
+ configure_usart0_pins(ATMEL_UART_CTS | ATMEL_UART_RTS | ATMEL_UART_DSR | ATMEL_UART_DTR | ATMEL_UART_DCD | ATMEL_UART_RI);
at91_uarts[i] = &at91sam9260_uart0_device;
at91_clock_associate("usart0_clk", &at91sam9260_uart0_device.dev, "usart");
break;
case 1:
- configure_usart1_pins();
+ configure_usart1_pins(ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_uarts[i] = &at91sam9260_uart1_device;
at91_clock_associate("usart1_clk", &at91sam9260_uart1_device.dev, "usart");
break;
case 2:
- configure_usart2_pins();
+ configure_usart2_pins(0);
at91_uarts[i] = &at91sam9260_uart2_device;
at91_clock_associate("usart2_clk", &at91sam9260_uart2_device.dev, "usart");
break;
case 3:
- configure_usart3_pins();
+ configure_usart3_pins(0);
at91_uarts[i] = &at91sam9260_uart3_device;
at91_clock_associate("usart3_clk", &at91sam9260_uart3_device.dev, "usart");
break;
@@ -1022,6 +1042,63 @@
printk(KERN_INFO "AT91: No default serial console defined.\n");
}
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
+{
+ struct platform_device *pdev;
+
+ switch (id) {
+ case 0: /* DBGU */
+ pdev = &at91sam9260_dbgu_device;
+ configure_dbgu_pins();
+ at91_clock_associate("mck", &pdev->dev, "usart");
+ break;
+ case AT91SAM9260_ID_US0:
+ pdev = &at91sam9260_uart0_device;
+ configure_usart0_pins(pins);
+ at91_clock_associate("usart0_clk", &pdev->dev, "usart");
+ break;
+ case AT91SAM9260_ID_US1:
+ pdev = &at91sam9260_uart1_device;
+ configure_usart1_pins(pins);
+ at91_clock_associate("usart1_clk", &pdev->dev, "usart");
+ break;
+ case AT91SAM9260_ID_US2:
+ pdev = &at91sam9260_uart2_device;
+ configure_usart2_pins(pins);
+ at91_clock_associate("usart2_clk", &pdev->dev, "usart");
+ break;
+ case AT91SAM9260_ID_US3:
+ pdev = &at91sam9260_uart3_device;
+ configure_usart3_pins(pins);
+ at91_clock_associate("usart3_clk", &pdev->dev, "usart");
+ break;
+ case AT91SAM9260_ID_US4:
+ pdev = &at91sam9260_uart4_device;
+ configure_usart4_pins();
+ at91_clock_associate("usart4_clk", &pdev->dev, "usart");
+ break;
+ case AT91SAM9260_ID_US5:
+ pdev = &at91sam9260_uart5_device;
+ configure_usart5_pins();
+ at91_clock_associate("usart5_clk", &pdev->dev, "usart");
+ break;
+ default:
+ return;
+ }
+ pdev->id = portnr; /* update to mapped ID */
+
+ if (portnr < ATMEL_MAX_UART)
+ at91_uarts[portnr] = pdev;
+}
+
+void __init at91_set_serial_console(unsigned portnr)
+{
+ if (portnr < ATMEL_MAX_UART)
+ atmel_default_console_device = at91_uarts[portnr];
+ if (!atmel_default_console_device)
+ printk(KERN_INFO "AT91: No default serial console defined.\n");
+}
+
void __init at91_add_device_serial(void)
{
int i;
@@ -1032,7 +1109,9 @@
}
}
#else
-void __init at91_init_serial(struct at91_uart_config *config) {}
+void __init __deprecated at91_init_serial(struct at91_uart_config *config) {}
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
+void __init at91_set_serial_console(unsigned portnr) {}
void __init at91_add_device_serial(void) {}
#endif
diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c
index ba84ba6..467a643 100644
--- a/arch/arm/mach-at91/at91sam9261_devices.c
+++ b/arch/arm/mach-at91/at91sam9261_devices.c
@@ -867,12 +867,15 @@
.num_resources = ARRAY_SIZE(uart0_resources),
};
-static inline void configure_usart0_pins(void)
+static inline void configure_usart0_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PC8, 1); /* TXD0 */
at91_set_A_periph(AT91_PIN_PC9, 0); /* RXD0 */
- at91_set_A_periph(AT91_PIN_PC10, 0); /* RTS0 */
- at91_set_A_periph(AT91_PIN_PC11, 0); /* CTS0 */
+
+ if (pins & ATMEL_UART_RTS)
+ at91_set_A_periph(AT91_PIN_PC10, 0); /* RTS0 */
+ if (pins & ATMEL_UART_CTS)
+ at91_set_A_periph(AT91_PIN_PC11, 0); /* CTS0 */
}
static struct resource uart1_resources[] = {
@@ -907,10 +910,15 @@
.num_resources = ARRAY_SIZE(uart1_resources),
};
-static inline void configure_usart1_pins(void)
+static inline void configure_usart1_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PC12, 1); /* TXD1 */
at91_set_A_periph(AT91_PIN_PC13, 0); /* RXD1 */
+
+ if (pins & ATMEL_UART_RTS)
+ at91_set_B_periph(AT91_PIN_PA12, 0); /* RTS1 */
+ if (pins & ATMEL_UART_CTS)
+ at91_set_B_periph(AT91_PIN_PA13, 0); /* CTS1 */
}
static struct resource uart2_resources[] = {
@@ -945,16 +953,21 @@
.num_resources = ARRAY_SIZE(uart2_resources),
};
-static inline void configure_usart2_pins(void)
+static inline void configure_usart2_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PC15, 0); /* RXD2 */
at91_set_A_periph(AT91_PIN_PC14, 1); /* TXD2 */
+
+ if (pins & ATMEL_UART_RTS)
+ at91_set_B_periph(AT91_PIN_PA15, 0); /* RTS2*/
+ if (pins & ATMEL_UART_CTS)
+ at91_set_B_periph(AT91_PIN_PA16, 0); /* CTS2 */
}
static struct platform_device *at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */
struct platform_device *atmel_default_console_device; /* the serial console device */
-void __init at91_init_serial(struct at91_uart_config *config)
+void __init __deprecated at91_init_serial(struct at91_uart_config *config)
{
int i;
@@ -962,17 +975,17 @@
for (i = 0; i < config->nr_tty; i++) {
switch (config->tty_map[i]) {
case 0:
- configure_usart0_pins();
+ configure_usart0_pins(ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_uarts[i] = &at91sam9261_uart0_device;
at91_clock_associate("usart0_clk", &at91sam9261_uart0_device.dev, "usart");
break;
case 1:
- configure_usart1_pins();
+ configure_usart1_pins(0);
at91_uarts[i] = &at91sam9261_uart1_device;
at91_clock_associate("usart1_clk", &at91sam9261_uart1_device.dev, "usart");
break;
case 2:
- configure_usart2_pins();
+ configure_usart2_pins(0);
at91_uarts[i] = &at91sam9261_uart2_device;
at91_clock_associate("usart2_clk", &at91sam9261_uart2_device.dev, "usart");
break;
@@ -994,6 +1007,48 @@
printk(KERN_INFO "AT91: No default serial console defined.\n");
}
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
+{
+ struct platform_device *pdev;
+
+ switch (id) {
+ case 0: /* DBGU */
+ pdev = &at91sam9261_dbgu_device;
+ configure_dbgu_pins();
+ at91_clock_associate("mck", &pdev->dev, "usart");
+ break;
+ case AT91SAM9261_ID_US0:
+ pdev = &at91sam9261_uart0_device;
+ configure_usart0_pins(pins);
+ at91_clock_associate("usart0_clk", &pdev->dev, "usart");
+ break;
+ case AT91SAM9261_ID_US1:
+ pdev = &at91sam9261_uart1_device;
+ configure_usart1_pins(pins);
+ at91_clock_associate("usart1_clk", &pdev->dev, "usart");
+ break;
+ case AT91SAM9261_ID_US2:
+ pdev = &at91sam9261_uart2_device;
+ configure_usart2_pins(pins);
+ at91_clock_associate("usart2_clk", &pdev->dev, "usart");
+ break;
+ default:
+ return;
+ }
+ pdev->id = portnr; /* update to mapped ID */
+
+ if (portnr < ATMEL_MAX_UART)
+ at91_uarts[portnr] = pdev;
+}
+
+void __init at91_set_serial_console(unsigned portnr)
+{
+ if (portnr < ATMEL_MAX_UART)
+ atmel_default_console_device = at91_uarts[portnr];
+ if (!atmel_default_console_device)
+ printk(KERN_INFO "AT91: No default serial console defined.\n");
+}
+
void __init at91_add_device_serial(void)
{
int i;
@@ -1004,7 +1059,9 @@
}
}
#else
-void __init at91_init_serial(struct at91_uart_config *config) {}
+void __init __deprecated at91_init_serial(struct at91_uart_config *config) {}
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
+void __init at91_set_serial_console(unsigned portnr) {}
void __init at91_add_device_serial(void) {}
#endif
diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
index c025f5c..a9f35d0 100644
--- a/arch/arm/mach-at91/at91sam9263_devices.c
+++ b/arch/arm/mach-at91/at91sam9263_devices.c
@@ -1071,12 +1071,15 @@
.num_resources = ARRAY_SIZE(uart0_resources),
};
-static inline void configure_usart0_pins(void)
+static inline void configure_usart0_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PA26, 1); /* TXD0 */
at91_set_A_periph(AT91_PIN_PA27, 0); /* RXD0 */
- at91_set_A_periph(AT91_PIN_PA28, 0); /* RTS0 */
- at91_set_A_periph(AT91_PIN_PA29, 0); /* CTS0 */
+
+ if (pins & ATMEL_UART_RTS)
+ at91_set_A_periph(AT91_PIN_PA28, 0); /* RTS0 */
+ if (pins & ATMEL_UART_CTS)
+ at91_set_A_periph(AT91_PIN_PA29, 0); /* CTS0 */
}
static struct resource uart1_resources[] = {
@@ -1111,12 +1114,15 @@
.num_resources = ARRAY_SIZE(uart1_resources),
};
-static inline void configure_usart1_pins(void)
+static inline void configure_usart1_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PD0, 1); /* TXD1 */
at91_set_A_periph(AT91_PIN_PD1, 0); /* RXD1 */
- at91_set_B_periph(AT91_PIN_PD7, 0); /* RTS1 */
- at91_set_B_periph(AT91_PIN_PD8, 0); /* CTS1 */
+
+ if (pins & ATMEL_UART_RTS)
+ at91_set_B_periph(AT91_PIN_PD7, 0); /* RTS1 */
+ if (pins & ATMEL_UART_CTS)
+ at91_set_B_periph(AT91_PIN_PD8, 0); /* CTS1 */
}
static struct resource uart2_resources[] = {
@@ -1151,18 +1157,21 @@
.num_resources = ARRAY_SIZE(uart2_resources),
};
-static inline void configure_usart2_pins(void)
+static inline void configure_usart2_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PD2, 1); /* TXD2 */
at91_set_A_periph(AT91_PIN_PD3, 0); /* RXD2 */
- at91_set_B_periph(AT91_PIN_PD5, 0); /* RTS2 */
- at91_set_B_periph(AT91_PIN_PD6, 0); /* CTS2 */
+
+ if (pins & ATMEL_UART_RTS)
+ at91_set_B_periph(AT91_PIN_PD5, 0); /* RTS2 */
+ if (pins & ATMEL_UART_CTS)
+ at91_set_B_periph(AT91_PIN_PD6, 0); /* CTS2 */
}
static struct platform_device *at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */
struct platform_device *atmel_default_console_device; /* the serial console device */
-void __init at91_init_serial(struct at91_uart_config *config)
+void __init __deprecated at91_init_serial(struct at91_uart_config *config)
{
int i;
@@ -1170,17 +1179,17 @@
for (i = 0; i < config->nr_tty; i++) {
switch (config->tty_map[i]) {
case 0:
- configure_usart0_pins();
+ configure_usart0_pins(ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_uarts[i] = &at91sam9263_uart0_device;
at91_clock_associate("usart0_clk", &at91sam9263_uart0_device.dev, "usart");
break;
case 1:
- configure_usart1_pins();
+ configure_usart1_pins(ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_uarts[i] = &at91sam9263_uart1_device;
at91_clock_associate("usart1_clk", &at91sam9263_uart1_device.dev, "usart");
break;
case 2:
- configure_usart2_pins();
+ configure_usart2_pins(ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_uarts[i] = &at91sam9263_uart2_device;
at91_clock_associate("usart2_clk", &at91sam9263_uart2_device.dev, "usart");
break;
@@ -1202,6 +1211,48 @@
printk(KERN_INFO "AT91: No default serial console defined.\n");
}
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
+{
+ struct platform_device *pdev;
+
+ switch (id) {
+ case 0: /* DBGU */
+ pdev = &at91sam9263_dbgu_device;
+ configure_dbgu_pins();
+ at91_clock_associate("mck", &pdev->dev, "usart");
+ break;
+ case AT91SAM9263_ID_US0:
+ pdev = &at91sam9263_uart0_device;
+ configure_usart0_pins(pins);
+ at91_clock_associate("usart0_clk", &pdev->dev, "usart");
+ break;
+ case AT91SAM9263_ID_US1:
+ pdev = &at91sam9263_uart1_device;
+ configure_usart1_pins(pins);
+ at91_clock_associate("usart1_clk", &pdev->dev, "usart");
+ break;
+ case AT91SAM9263_ID_US2:
+ pdev = &at91sam9263_uart2_device;
+ configure_usart2_pins(pins);
+ at91_clock_associate("usart2_clk", &pdev->dev, "usart");
+ break;
+ default:
+ return;
+ }
+ pdev->id = portnr; /* update to mapped ID */
+
+ if (portnr < ATMEL_MAX_UART)
+ at91_uarts[portnr] = pdev;
+}
+
+void __init at91_set_serial_console(unsigned portnr)
+{
+ if (portnr < ATMEL_MAX_UART)
+ atmel_default_console_device = at91_uarts[portnr];
+ if (!atmel_default_console_device)
+ printk(KERN_INFO "AT91: No default serial console defined.\n");
+}
+
void __init at91_add_device_serial(void)
{
int i;
@@ -1213,6 +1264,8 @@
}
#else
void __init at91_init_serial(struct at91_uart_config *config) {}
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
+void __init at91_set_serial_console(unsigned portnr) {}
void __init at91_add_device_serial(void) {}
#endif
diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c
index e886cdf..a942b9e 100644
--- a/arch/arm/mach-at91/at91sam9rl_devices.c
+++ b/arch/arm/mach-at91/at91sam9rl_devices.c
@@ -676,12 +676,23 @@
.num_resources = ARRAY_SIZE(uart0_resources),
};
-static inline void configure_usart0_pins(void)
+static inline void configure_usart0_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PA6, 1); /* TXD0 */
at91_set_A_periph(AT91_PIN_PA7, 0); /* RXD0 */
- at91_set_A_periph(AT91_PIN_PA9, 0); /* RTS0 */
- at91_set_A_periph(AT91_PIN_PA10, 0); /* CTS0 */
+
+ if (pins & ATMEL_UART_RTS)
+ at91_set_A_periph(AT91_PIN_PA9, 0); /* RTS0 */
+ if (pins & ATMEL_UART_CTS)
+ at91_set_A_periph(AT91_PIN_PA10, 0); /* CTS0 */
+ if (pins & ATMEL_UART_DSR)
+ at91_set_A_periph(AT91_PIN_PD14, 0); /* DSR0 */
+ if (pins & ATMEL_UART_DTR)
+ at91_set_A_periph(AT91_PIN_PD15, 0); /* DTR0 */
+ if (pins & ATMEL_UART_DCD)
+ at91_set_A_periph(AT91_PIN_PD16, 0); /* DCD0 */
+ if (pins & ATMEL_UART_RI)
+ at91_set_A_periph(AT91_PIN_PD17, 0); /* RI0 */
}
static struct resource uart1_resources[] = {
@@ -716,10 +727,15 @@
.num_resources = ARRAY_SIZE(uart1_resources),
};
-static inline void configure_usart1_pins(void)
+static inline void configure_usart1_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PA11, 1); /* TXD1 */
at91_set_A_periph(AT91_PIN_PA12, 0); /* RXD1 */
+
+ if (pins & ATMEL_UART_RTS)
+ at91_set_B_periph(AT91_PIN_PA18, 0); /* RTS1 */
+ if (pins & ATMEL_UART_CTS)
+ at91_set_B_periph(AT91_PIN_PA19, 0); /* CTS1 */
}
static struct resource uart2_resources[] = {
@@ -754,10 +770,15 @@
.num_resources = ARRAY_SIZE(uart2_resources),
};
-static inline void configure_usart2_pins(void)
+static inline void configure_usart2_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PA13, 1); /* TXD2 */
at91_set_A_periph(AT91_PIN_PA14, 0); /* RXD2 */
+
+ if (pins & ATMEL_UART_RTS)
+ at91_set_A_periph(AT91_PIN_PA29, 0); /* RTS2 */
+ if (pins & ATMEL_UART_CTS)
+ at91_set_A_periph(AT91_PIN_PA30, 0); /* CTS2 */
}
static struct resource uart3_resources[] = {
@@ -792,16 +813,21 @@
.num_resources = ARRAY_SIZE(uart3_resources),
};
-static inline void configure_usart3_pins(void)
+static inline void configure_usart3_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PB0, 1); /* TXD3 */
at91_set_A_periph(AT91_PIN_PB1, 0); /* RXD3 */
+
+ if (pins & ATMEL_UART_RTS)
+ at91_set_B_periph(AT91_PIN_PD4, 0); /* RTS3 */
+ if (pins & ATMEL_UART_CTS)
+ at91_set_B_periph(AT91_PIN_PD3, 0); /* CTS3 */
}
static struct platform_device *at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */
struct platform_device *atmel_default_console_device; /* the serial console device */
-void __init at91_init_serial(struct at91_uart_config *config)
+void __init __deprecated at91_init_serial(struct at91_uart_config *config)
{
int i;
@@ -809,22 +835,22 @@
for (i = 0; i < config->nr_tty; i++) {
switch (config->tty_map[i]) {
case 0:
- configure_usart0_pins();
+ configure_usart0_pins(ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_uarts[i] = &at91sam9rl_uart0_device;
at91_clock_associate("usart0_clk", &at91sam9rl_uart0_device.dev, "usart");
break;
case 1:
- configure_usart1_pins();
+ configure_usart1_pins(0);
at91_uarts[i] = &at91sam9rl_uart1_device;
at91_clock_associate("usart1_clk", &at91sam9rl_uart1_device.dev, "usart");
break;
case 2:
- configure_usart2_pins();
+ configure_usart2_pins(0);
at91_uarts[i] = &at91sam9rl_uart2_device;
at91_clock_associate("usart2_clk", &at91sam9rl_uart2_device.dev, "usart");
break;
case 3:
- configure_usart3_pins();
+ configure_usart3_pins(0);
at91_uarts[i] = &at91sam9rl_uart3_device;
at91_clock_associate("usart3_clk", &at91sam9rl_uart3_device.dev, "usart");
break;
@@ -846,6 +872,53 @@
printk(KERN_INFO "AT91: No default serial console defined.\n");
}
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
+{
+ struct platform_device *pdev;
+
+ switch (id) {
+ case 0: /* DBGU */
+ pdev = &at91sam9rl_dbgu_device;
+ configure_dbgu_pins();
+ at91_clock_associate("mck", &pdev->dev, "usart");
+ break;
+ case AT91SAM9RL_ID_US0:
+ pdev = &at91sam9rl_uart0_device;
+ configure_usart0_pins(pins);
+ at91_clock_associate("usart0_clk", &pdev->dev, "usart");
+ break;
+ case AT91SAM9RL_ID_US1:
+ pdev = &at91sam9rl_uart1_device;
+ configure_usart1_pins(pins);
+ at91_clock_associate("usart1_clk", &pdev->dev, "usart");
+ break;
+ case AT91SAM9RL_ID_US2:
+ pdev = &at91sam9rl_uart2_device;
+ configure_usart2_pins(pins);
+ at91_clock_associate("usart2_clk", &pdev->dev, "usart");
+ break;
+ case AT91SAM9RL_ID_US3:
+ pdev = &at91sam9rl_uart3_device;
+ configure_usart3_pins(pins);
+ at91_clock_associate("usart3_clk", &pdev->dev, "usart");
+ break;
+ default:
+ return;
+ }
+ pdev->id = portnr; /* update to mapped ID */
+
+ if (portnr < ATMEL_MAX_UART)
+ at91_uarts[portnr] = pdev;
+}
+
+void __init at91_set_serial_console(unsigned portnr)
+{
+ if (portnr < ATMEL_MAX_UART)
+ atmel_default_console_device = at91_uarts[portnr];
+ if (!atmel_default_console_device)
+ printk(KERN_INFO "AT91: No default serial console defined.\n");
+}
+
void __init at91_add_device_serial(void)
{
int i;
@@ -856,7 +929,9 @@
}
}
#else
-void __init at91_init_serial(struct at91_uart_config *config) {}
+void __init __deprecated at91_init_serial(struct at91_uart_config *config) {}
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
+void __init at91_set_serial_console(unsigned portnr) {}
void __init at91_add_device_serial(void) {}
#endif
diff --git a/include/asm-arm/arch-at91/board.h b/include/asm-arm/arch-at91/board.h
index 7fefe01..3f41ab2 100644
--- a/include/asm-arm/arch-at91/board.h
+++ b/include/asm-arm/arch-at91/board.h
@@ -101,13 +101,23 @@
extern void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices);
/* Serial */
+#define ATMEL_UART_CTS 0x01
+#define ATMEL_UART_RTS 0x02
+#define ATMEL_UART_DSR 0x04
+#define ATMEL_UART_DTR 0x08
+#define ATMEL_UART_DCD 0x10
+#define ATMEL_UART_RI 0x20
+
+extern void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins);
+extern void __init at91_set_serial_console(unsigned portnr);
+
struct at91_uart_config {
unsigned short console_tty; /* tty number of serial console */
unsigned short nr_tty; /* number of serial tty's */
short tty_map[]; /* map UART to tty number */
};
extern struct platform_device *atmel_default_console_device;
-extern void __init at91_init_serial(struct at91_uart_config *config);
+extern void __init __deprecated at91_init_serial(struct at91_uart_config *config);
struct atmel_uart_data {
short use_dma_tx; /* use transmit DMA? */