blob: c55c77043357cb0243a4b368a1e6d63b7a4af398 [file] [log] [blame]
/*
* Copyright © 2006-2007 Intel Corporation
*
* Permission is hereby granted, free of charge, to any person obtaining a
* copy of this software and associated documentation files (the "Software"),
* to deal in the Software without restriction, including without limitation
* the rights to use, copy, modify, merge, publish, distribute, sublicense,
* and/or sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following conditions:
*
* The above copyright notice and this permission notice (including the next
* paragraph) shall be included in all copies or substantial portions of the
* Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
* THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
* DEALINGS IN THE SOFTWARE.
*
* Authors:
* Eric Anholt <eric@anholt.net>
*/
#include <linux/i2c.h>
#include <linux/slab.h>
#include "drmP.h"
#include "drm.h"
#include "drm_crtc.h"
#include "drm_crtc_helper.h"
#include "intel_drv.h"
#include "i915_drm.h"
#include "i915_drv.h"
static void intel_crt_dpms(struct drm_encoder *encoder, int mode)
{
struct drm_device *dev = encoder->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
u32 temp, reg;
if (HAS_PCH_SPLIT(dev))
reg = PCH_ADPA;
else
reg = ADPA;
temp = I915_READ(reg);
temp &= ~(ADPA_HSYNC_CNTL_DISABLE | ADPA_VSYNC_CNTL_DISABLE);
temp &= ~ADPA_DAC_ENABLE;
switch(mode) {
case DRM_MODE_DPMS_ON:
temp |= ADPA_DAC_ENABLE;
break;
case DRM_MODE_DPMS_STANDBY:
temp |= ADPA_DAC_ENABLE | ADPA_HSYNC_CNTL_DISABLE;
break;
case DRM_MODE_DPMS_SUSPEND:
temp |= ADPA_DAC_ENABLE | ADPA_VSYNC_CNTL_DISABLE;
break;
case DRM_MODE_DPMS_OFF:
temp |= ADPA_HSYNC_CNTL_DISABLE | ADPA_VSYNC_CNTL_DISABLE;
break;
}
I915_WRITE(reg, temp);
}
static int intel_crt_mode_valid(struct drm_connector *connector,
struct drm_display_mode *mode)
{
struct drm_device *dev = connector->dev;
int max_clock = 0;
if (mode->flags & DRM_MODE_FLAG_DBLSCAN)
return MODE_NO_DBLESCAN;
if (mode->clock < 25000)
return MODE_CLOCK_LOW;
if (IS_GEN2(dev))
max_clock = 350000;
else
max_clock = 400000;
if (mode->clock > max_clock)
return MODE_CLOCK_HIGH;
return MODE_OK;
}
static bool intel_crt_mode_fixup(struct drm_encoder *encoder,
struct drm_display_mode *mode,
struct drm_display_mode *adjusted_mode)
{
return true;
}
static void intel_crt_mode_set(struct drm_encoder *encoder,
struct drm_display_mode *mode,
struct drm_display_mode *adjusted_mode)
{
struct drm_device *dev = encoder->dev;
struct drm_crtc *crtc = encoder->crtc;
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
struct drm_i915_private *dev_priv = dev->dev_private;
int dpll_md_reg;
u32 adpa, dpll_md;
u32 adpa_reg;
if (intel_crtc->pipe == 0)
dpll_md_reg = DPLL_A_MD;
else
dpll_md_reg = DPLL_B_MD;
if (HAS_PCH_SPLIT(dev))
adpa_reg = PCH_ADPA;
else
adpa_reg = ADPA;
/*
* Disable separate mode multiplier used when cloning SDVO to CRT
* XXX this needs to be adjusted when we really are cloning
*/
if (INTEL_INFO(dev)->gen >= 4 && !HAS_PCH_SPLIT(dev)) {
dpll_md = I915_READ(dpll_md_reg);
I915_WRITE(dpll_md_reg,
dpll_md & ~DPLL_MD_UDI_MULTIPLIER_MASK);
}
adpa = 0;
if (adjusted_mode->flags & DRM_MODE_FLAG_PHSYNC)
adpa |= ADPA_HSYNC_ACTIVE_HIGH;
if (adjusted_mode->flags & DRM_MODE_FLAG_PVSYNC)
adpa |= ADPA_VSYNC_ACTIVE_HIGH;
if (intel_crtc->pipe == 0) {
if (HAS_PCH_CPT(dev))
adpa |= PORT_TRANS_A_SEL_CPT;
else
adpa |= ADPA_PIPE_A_SELECT;
if (!HAS_PCH_SPLIT(dev))
I915_WRITE(BCLRPAT_A, 0);
} else {
if (HAS_PCH_CPT(dev))
adpa |= PORT_TRANS_B_SEL_CPT;
else
adpa |= ADPA_PIPE_B_SELECT;
if (!HAS_PCH_SPLIT(dev))
I915_WRITE(BCLRPAT_B, 0);
}
I915_WRITE(adpa_reg, adpa);
}
static bool intel_ironlake_crt_detect_hotplug(struct drm_connector *connector)
{
struct drm_device *dev = connector->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
u32 adpa, temp;
bool ret;
bool turn_off_dac = false;
temp = adpa = I915_READ(PCH_ADPA);
if (HAS_PCH_SPLIT(dev))
turn_off_dac = true;
adpa &= ~ADPA_CRT_HOTPLUG_MASK;
if (turn_off_dac)
adpa &= ~ADPA_DAC_ENABLE;
/* disable HPD first */
I915_WRITE(PCH_ADPA, adpa);
(void)I915_READ(PCH_ADPA);
adpa |= (ADPA_CRT_HOTPLUG_PERIOD_128 |
ADPA_CRT_HOTPLUG_WARMUP_10MS |
ADPA_CRT_HOTPLUG_SAMPLE_4S |
ADPA_CRT_HOTPLUG_VOLTAGE_50 | /* default */
ADPA_CRT_HOTPLUG_VOLREF_325MV |
ADPA_CRT_HOTPLUG_ENABLE |
ADPA_CRT_HOTPLUG_FORCE_TRIGGER);
DRM_DEBUG_KMS("pch crt adpa 0x%x", adpa);
I915_WRITE(PCH_ADPA, adpa);
if (wait_for((I915_READ(PCH_ADPA) & ADPA_CRT_HOTPLUG_FORCE_TRIGGER) == 0,
1000))
DRM_DEBUG_KMS("timed out waiting for FORCE_TRIGGER");
if (turn_off_dac) {
/* Make sure hotplug is enabled */
I915_WRITE(PCH_ADPA, temp | ADPA_CRT_HOTPLUG_ENABLE);
(void)I915_READ(PCH_ADPA);
}
/* Check the status to see if both blue and green are on now */
adpa = I915_READ(PCH_ADPA);
adpa &= ADPA_CRT_HOTPLUG_MONITOR_MASK;
if ((adpa == ADPA_CRT_HOTPLUG_MONITOR_COLOR) ||
(adpa == ADPA_CRT_HOTPLUG_MONITOR_MONO))
ret = true;
else
ret = false;
return ret;
}
/**
* Uses CRT_HOTPLUG_EN and CRT_HOTPLUG_STAT to detect CRT presence.
*
* Not for i915G/i915GM
*
* \return true if CRT is connected.
* \return false if CRT is disconnected.
*/
static bool intel_crt_detect_hotplug(struct drm_connector *connector)
{
struct drm_device *dev = connector->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
u32 hotplug_en, orig, stat;
bool ret = false;
int i, tries = 0;
if (HAS_PCH_SPLIT(dev))
return intel_ironlake_crt_detect_hotplug(connector);
/*
* On 4 series desktop, CRT detect sequence need to be done twice
* to get a reliable result.
*/
if (IS_G4X(dev) && !IS_GM45(dev))
tries = 2;
else
tries = 1;
hotplug_en = orig = I915_READ(PORT_HOTPLUG_EN);
hotplug_en |= CRT_HOTPLUG_FORCE_DETECT;
for (i = 0; i < tries ; i++) {
/* turn on the FORCE_DETECT */
I915_WRITE(PORT_HOTPLUG_EN, hotplug_en);
/* wait for FORCE_DETECT to go off */
if (wait_for((I915_READ(PORT_HOTPLUG_EN) &
CRT_HOTPLUG_FORCE_DETECT) == 0,
1000))
DRM_DEBUG_KMS("timed out waiting for FORCE_DETECT to go off");
}
stat = I915_READ(PORT_HOTPLUG_STAT);
if ((stat & CRT_HOTPLUG_MONITOR_MASK) != CRT_HOTPLUG_MONITOR_NONE)
ret = true;
/* clear the interrupt we just generated, if any */
I915_WRITE(PORT_HOTPLUG_STAT, CRT_HOTPLUG_INT_STATUS);
/* and put the bits back */
I915_WRITE(PORT_HOTPLUG_EN, orig);
return ret;
}
static bool intel_crt_ddc_probe(struct drm_i915_private *dev_priv, int ddc_bus)
{
u8 buf;
struct i2c_msg msgs[] = {
{
.addr = 0xA0,
.flags = 0,
.len = 1,
.buf = &buf,
},
};
/* DDC monitor detect: Does it ACK a write to 0xA0? */
return i2c_transfer(&dev_priv->gmbus[ddc_bus].adapter, msgs, 1) == 1;
}
static bool intel_crt_detect_ddc(struct drm_encoder *encoder)
{
struct intel_encoder *intel_encoder = to_intel_encoder(encoder);
struct drm_i915_private *dev_priv = encoder->dev->dev_private;
/* CRT should always be at 0, but check anyway */
if (intel_encoder->type != INTEL_OUTPUT_ANALOG)
return false;
if (intel_crt_ddc_probe(dev_priv, dev_priv->crt_ddc_pin)) {
DRM_DEBUG_KMS("CRT detected via DDC:0xa0\n");
return true;
}
if (intel_ddc_probe(intel_encoder, dev_priv->crt_ddc_pin)) {
DRM_DEBUG_KMS("CRT detected via DDC:0x50 [EDID]\n");
return true;
}
return false;
}
static enum drm_connector_status
intel_crt_load_detect(struct drm_crtc *crtc, struct intel_encoder *intel_encoder)
{
struct drm_encoder *encoder = &intel_encoder->base;
struct drm_device *dev = encoder->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
uint32_t pipe = intel_crtc->pipe;
uint32_t save_bclrpat;
uint32_t save_vtotal;
uint32_t vtotal, vactive;
uint32_t vsample;
uint32_t vblank, vblank_start, vblank_end;
uint32_t dsl;
uint32_t bclrpat_reg;
uint32_t vtotal_reg;
uint32_t vblank_reg;
uint32_t vsync_reg;
uint32_t pipeconf_reg;
uint32_t pipe_dsl_reg;
uint8_t st00;
enum drm_connector_status status;
DRM_DEBUG_KMS("starting load-detect on CRT\n");
if (pipe == 0) {
bclrpat_reg = BCLRPAT_A;
vtotal_reg = VTOTAL_A;
vblank_reg = VBLANK_A;
vsync_reg = VSYNC_A;
pipeconf_reg = PIPEACONF;
pipe_dsl_reg = PIPEADSL;
} else {
bclrpat_reg = BCLRPAT_B;
vtotal_reg = VTOTAL_B;
vblank_reg = VBLANK_B;
vsync_reg = VSYNC_B;
pipeconf_reg = PIPEBCONF;
pipe_dsl_reg = PIPEBDSL;
}
save_bclrpat = I915_READ(bclrpat_reg);
save_vtotal = I915_READ(vtotal_reg);
vblank = I915_READ(vblank_reg);
vtotal = ((save_vtotal >> 16) & 0xfff) + 1;
vactive = (save_vtotal & 0x7ff) + 1;
vblank_start = (vblank & 0xfff) + 1;
vblank_end = ((vblank >> 16) & 0xfff) + 1;
/* Set the border color to purple. */
I915_WRITE(bclrpat_reg, 0x500050);
if (!IS_GEN2(dev)) {
uint32_t pipeconf = I915_READ(pipeconf_reg);
I915_WRITE(pipeconf_reg, pipeconf | PIPECONF_FORCE_BORDER);
POSTING_READ(pipeconf_reg);
/* Wait for next Vblank to substitue
* border color for Color info */
intel_wait_for_vblank(dev, pipe);
st00 = I915_READ8(VGA_MSR_WRITE);
status = ((st00 & (1 << 4)) != 0) ?
connector_status_connected :
connector_status_disconnected;
I915_WRITE(pipeconf_reg, pipeconf);
} else {
bool restore_vblank = false;
int count, detect;
/*
* If there isn't any border, add some.
* Yes, this will flicker
*/
if (vblank_start <= vactive && vblank_end >= vtotal) {
uint32_t vsync = I915_READ(vsync_reg);
uint32_t vsync_start = (vsync & 0xffff) + 1;
vblank_start = vsync_start;
I915_WRITE(vblank_reg,
(vblank_start - 1) |
((vblank_end - 1) << 16));
restore_vblank = true;
}
/* sample in the vertical border, selecting the larger one */
if (vblank_start - vactive >= vtotal - vblank_end)
vsample = (vblank_start + vactive) >> 1;
else
vsample = (vtotal + vblank_end) >> 1;
/*
* Wait for the border to be displayed
*/
while (I915_READ(pipe_dsl_reg) >= vactive)
;
while ((dsl = I915_READ(pipe_dsl_reg)) <= vsample)
;
/*
* Watch ST00 for an entire scanline
*/
detect = 0;
count = 0;
do {
count++;
/* Read the ST00 VGA status register */
st00 = I915_READ8(VGA_MSR_WRITE);
if (st00 & (1 << 4))
detect++;
} while ((I915_READ(pipe_dsl_reg) == dsl));
/* restore vblank if necessary */
if (restore_vblank)
I915_WRITE(vblank_reg, vblank);
/*
* If more than 3/4 of the scanline detected a monitor,
* then it is assumed to be present. This works even on i830,
* where there isn't any way to force the border color across
* the screen
*/
status = detect * 4 > count * 3 ?
connector_status_connected :
connector_status_disconnected;
}
/* Restore previous settings */
I915_WRITE(bclrpat_reg, save_bclrpat);
return status;
}
static enum drm_connector_status
intel_crt_detect(struct drm_connector *connector, bool force)
{
struct drm_device *dev = connector->dev;
struct intel_encoder *encoder = intel_attached_encoder(connector);
struct drm_crtc *crtc;
int dpms_mode;
enum drm_connector_status status;
if (I915_HAS_HOTPLUG(dev)) {
if (intel_crt_detect_hotplug(connector)) {
DRM_DEBUG_KMS("CRT detected via hotplug\n");
return connector_status_connected;
} else
return connector_status_disconnected;
}
if (intel_crt_detect_ddc(&encoder->base))
return connector_status_connected;
if (!force)
return connector->status;
/* for pre-945g platforms use load detect */
if (encoder->base.crtc && encoder->base.crtc->enabled) {
status = intel_crt_load_detect(encoder->base.crtc, encoder);
} else {
crtc = intel_get_load_detect_pipe(encoder, connector,
NULL, &dpms_mode);
if (crtc) {
if (intel_crt_detect_ddc(&encoder->base))
status = connector_status_connected;
else
status = intel_crt_load_detect(crtc, encoder);
intel_release_load_detect_pipe(encoder,
connector, dpms_mode);
} else
status = connector_status_unknown;
}
return status;
}
static void intel_crt_destroy(struct drm_connector *connector)
{
drm_sysfs_connector_remove(connector);
drm_connector_cleanup(connector);
kfree(connector);
}
static int intel_crt_get_modes(struct drm_connector *connector)
{
struct drm_device *dev = connector->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
int ret;
ret = intel_ddc_get_modes(connector,
&dev_priv->gmbus[dev_priv->crt_ddc_pin].adapter);
if (ret || !IS_G4X(dev))
return ret;
/* Try to probe digital port for output in DVI-I -> VGA mode. */
return intel_ddc_get_modes(connector,
&dev_priv->gmbus[GMBUS_PORT_DPB].adapter);
}
static int intel_crt_set_property(struct drm_connector *connector,
struct drm_property *property,
uint64_t value)
{
return 0;
}
/*
* Routines for controlling stuff on the analog port
*/
static const struct drm_encoder_helper_funcs intel_crt_helper_funcs = {
.dpms = intel_crt_dpms,
.mode_fixup = intel_crt_mode_fixup,
.prepare = intel_encoder_prepare,
.commit = intel_encoder_commit,
.mode_set = intel_crt_mode_set,
};
static const struct drm_connector_funcs intel_crt_connector_funcs = {
.dpms = drm_helper_connector_dpms,
.detect = intel_crt_detect,
.fill_modes = drm_helper_probe_single_connector_modes,
.destroy = intel_crt_destroy,
.set_property = intel_crt_set_property,
};
static const struct drm_connector_helper_funcs intel_crt_connector_helper_funcs = {
.mode_valid = intel_crt_mode_valid,
.get_modes = intel_crt_get_modes,
.best_encoder = intel_best_encoder,
};
static const struct drm_encoder_funcs intel_crt_enc_funcs = {
.destroy = intel_encoder_destroy,
};
void intel_crt_init(struct drm_device *dev)
{
struct drm_connector *connector;
struct intel_encoder *intel_encoder;
struct intel_connector *intel_connector;
struct drm_i915_private *dev_priv = dev->dev_private;
intel_encoder = kzalloc(sizeof(struct intel_encoder), GFP_KERNEL);
if (!intel_encoder)
return;
intel_connector = kzalloc(sizeof(struct intel_connector), GFP_KERNEL);
if (!intel_connector) {
kfree(intel_encoder);
return;
}
connector = &intel_connector->base;
drm_connector_init(dev, &intel_connector->base,
&intel_crt_connector_funcs, DRM_MODE_CONNECTOR_VGA);
drm_encoder_init(dev, &intel_encoder->base, &intel_crt_enc_funcs,
DRM_MODE_ENCODER_DAC);
intel_connector_attach_encoder(intel_connector, intel_encoder);
intel_encoder->type = INTEL_OUTPUT_ANALOG;
intel_encoder->clone_mask = (1 << INTEL_SDVO_NON_TV_CLONE_BIT) |
(1 << INTEL_ANALOG_CLONE_BIT) |
(1 << INTEL_SDVO_LVDS_CLONE_BIT);
intel_encoder->crtc_mask = (1 << 0) | (1 << 1);
connector->interlace_allowed = 1;
connector->doublescan_allowed = 0;
drm_encoder_helper_add(&intel_encoder->base, &intel_crt_helper_funcs);
drm_connector_helper_add(connector, &intel_crt_connector_helper_funcs);
drm_sysfs_connector_add(connector);
if (I915_HAS_HOTPLUG(dev))
connector->polled = DRM_CONNECTOR_POLL_HPD;
else
connector->polled = DRM_CONNECTOR_POLL_CONNECT;
dev_priv->hotplug_supported_mask |= CRT_HOTPLUG_INT_STATUS;
}