[ALSA] hda-intel - Add POWER_SAVE option
Added CONFIG_SND_HDA_POWER_SAVE kconfig. It's an experimental option
to achieve an aggressive power-saving. With this option, the driver
will turn on/off the power of each codec and controller chip dynamically
on demand.
The patch introduces a new module option 'power_save'. It specifies
the second of time-out for automatic power-down. As default, it's
10 seconds. Setting 0 means to suppress the power-saving feature.
The codec may have analog-input loopbacks, which are usually represented
by mixer elements such as 'Mic Playback Switch' or 'CD Playback Switch'.
When these are on, we cannot turn off the mixer and the codec chip has
to be kept on. For bookkeeping these states, a new codec-callback is
introduced.
For the bus-controller side, a new callback pm_notify is introduced,
which can be used to turn on/off the contoller appropriately.
Note that this power-saving might cause slight click-noise at
power-on/off. Also, it might take some time to wake up the codec, and
might even drop some tones at the very beginning. This seems to be the
side-effect of turning off the controller chip.
This turn-off of the controller can be disabled by undefining
HDA_POWER_SAVE_RESET_CONTOLLER in hda_intel.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c
index ebbabeb..b3d3916 100644
--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -240,6 +240,10 @@
/* for pin sensing */
unsigned int sense_updated: 1;
unsigned int jack_present: 1;
+
+#ifdef CONFIG_SND_HDA_POWER_SAVE
+ struct hda_loopback_check loopback;
+#endif
};
/*
@@ -264,6 +268,9 @@
const struct hda_input_mux *input_mux;
void (*unsol_event)(struct hda_codec *, unsigned int);
void (*init_hook)(struct hda_codec *);
+#ifdef CONFIG_SND_HDA_POWER_SAVE
+ struct hda_amp_list *loopbacks;
+#endif
};
@@ -621,6 +628,9 @@
spec->unsol_event = preset->unsol_event;
spec->init_hook = preset->init_hook;
+#ifdef CONFIG_SND_HDA_POWER_SAVE
+ spec->loopback.amplist = preset->loopbacks;
+#endif
}
/* Enable GPIO mask and set output */
@@ -1287,11 +1297,13 @@
* panel mic (mic 2)
*/
/* Amp Indices: Mic1 = 0, Mic2 = 1, Line1 = 2, Line2 = 3, CD = 4 */
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(1)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(2)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(3)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(4)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(6)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(7)},
/*
* Set up output mixers (0x0c - 0x0f)
@@ -1836,8 +1848,8 @@
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(1)},
/* mute all amp mixer inputs */
{0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(5)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(6)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(7)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(6)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(7)},
/* line-in to input */
{0x14, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_IN},
{0x14, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
@@ -1939,7 +1951,7 @@
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(7)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(7)},
/* speaker-out */
{0x14, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_HP},
{0x14, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
@@ -1979,6 +1991,24 @@
alc880_lg_lw_automute(codec);
}
+#ifdef CONFIG_SND_HDA_POWER_SAVE
+static struct hda_amp_list alc880_loopbacks[] = {
+ { 0x0b, HDA_INPUT, 0 },
+ { 0x0b, HDA_INPUT, 1 },
+ { 0x0b, HDA_INPUT, 2 },
+ { 0x0b, HDA_INPUT, 3 },
+ { 0x0b, HDA_INPUT, 4 },
+ { } /* end */
+};
+
+static struct hda_amp_list alc880_lg_loopbacks[] = {
+ { 0x0b, HDA_INPUT, 1 },
+ { 0x0b, HDA_INPUT, 6 },
+ { 0x0b, HDA_INPUT, 7 },
+ { } /* end */
+};
+#endif
+
/*
* Common callbacks
*/
@@ -2005,6 +2035,14 @@
spec->unsol_event(codec, res);
}
+#ifdef CONFIG_SND_HDA_POWER_SAVE
+static int alc_check_power_status(struct hda_codec *codec, hda_nid_t nid)
+{
+ struct alc_spec *spec = codec->spec;
+ return snd_hda_check_amp_list_power(codec, &spec->loopback, nid);
+}
+#endif
+
/*
* Analog playback callbacks
*/
@@ -2236,6 +2274,9 @@
.init = alc_init,
.free = alc_free,
.unsol_event = alc_unsol_event,
+#ifdef CONFIG_SND_HDA_POWER_SAVE
+ .check_power_status = alc_check_power_status,
+#endif
};
@@ -2860,6 +2901,9 @@
.input_mux = &alc880_lg_capture_source,
.unsol_event = alc880_lg_unsol_event,
.init_hook = alc880_lg_automute,
+#ifdef CONFIG_SND_HDA_POWER_SAVE
+ .loopbacks = alc880_lg_loopbacks,
+#endif
},
[ALC880_LG_LW] = {
.mixers = { alc880_lg_lw_mixer },
@@ -3343,6 +3387,10 @@
codec->patch_ops = alc_patch_ops;
if (board_config == ALC880_AUTO)
spec->init_hook = alc880_auto_init;
+#ifdef CONFIG_SND_HDA_POWER_SAVE
+ if (!spec->loopback.amplist)
+ spec->loopback.amplist = alc880_loopbacks;
+#endif
return 0;
}
@@ -3691,12 +3739,12 @@
/* Amp Indexes: CD = 0x04, Line In 1 = 0x02, Mic 1 = 0x00 &
* Line In 2 = 0x03
*/
- /* mute CD */
- {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(4)},
- /* mute Line In */
- {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(2)},
- /* mute Mic */
- {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
+ /* mute analog inputs */
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)},
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)},
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)},
/* Amp Indexes: DAC = 0x01 & mixer = 0x00 */
/* mute Front out path */
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
@@ -3741,12 +3789,12 @@
/* Amp Indexes: CD = 0x04, Line In 1 = 0x02, Mic 1 = 0x00 &
* Line In 2 = 0x03
*/
- /* unmute CD */
- {0x07, AC_VERB_SET_AMP_GAIN_MUTE, (0x7000 | (0x04 << 8))},
- /* unmute Line In */
- {0x07, AC_VERB_SET_AMP_GAIN_MUTE, (0x7000 | (0x02 << 8))},
- /* unmute Mic */
- {0x07, AC_VERB_SET_AMP_GAIN_MUTE, (0x7000 | (0x00 << 8))},
+ /* mute analog inputs */
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)},
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)},
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)},
/* Amp Indexes: DAC = 0x01 & mixer = 0x00 */
/* Unmute Front out path */
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, (0x7000 | (0x00 << 8))},
@@ -3791,12 +3839,12 @@
/* Amp Indexes: CD = 0x04, Line In 1 = 0x02, Mic 1 = 0x00 &
* Line In 2 = 0x03
*/
- /* unmute CD */
- {0x07, AC_VERB_SET_AMP_GAIN_MUTE, (0x7000 | (0x04 << 8))},
- /* unmute Line In */
- {0x07, AC_VERB_SET_AMP_GAIN_MUTE, (0x7000 | (0x02 << 8))},
- /* unmute Mic */
- {0x07, AC_VERB_SET_AMP_GAIN_MUTE, (0x7000 | (0x00 << 8))},
+ /* mute analog inputs */
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)},
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)},
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)},
/* Amp Indexes: DAC = 0x01 & mixer = 0x00 */
/* Unmute Front out path */
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, (0x7000 | (0x00 << 8))},
@@ -4418,11 +4466,12 @@
* front panel mic (mic 2)
*/
/* Amp Indices: Mic1 = 0, Mic2 = 1, Line1 = 2, Line2 = 3, CD = 4 */
- {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
- {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(1)},
- {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(2)},
- {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(3)},
- {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(4)},
+ /* mute analog inputs */
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)},
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)},
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)},
/*
* Set up output mixers (0x08 - 0x0a)
@@ -4499,6 +4548,17 @@
alc260_auto_init_analog_input(codec);
}
+#ifdef CONFIG_SND_HDA_POWER_SAVE
+static struct hda_amp_list alc260_loopbacks[] = {
+ { 0x07, HDA_INPUT, 0 },
+ { 0x07, HDA_INPUT, 1 },
+ { 0x07, HDA_INPUT, 2 },
+ { 0x07, HDA_INPUT, 3 },
+ { 0x07, HDA_INPUT, 4 },
+ { } /* end */
+};
+#endif
+
/*
* ALC260 configurations
*/
@@ -4698,6 +4758,10 @@
codec->patch_ops = alc_patch_ops;
if (board_config == ALC260_AUTO)
spec->init_hook = alc260_auto_init;
+#ifdef CONFIG_SND_HDA_POWER_SAVE
+ if (!spec->loopback.amplist)
+ spec->loopback.amplist = alc260_loopbacks;
+#endif
return 0;
}
@@ -5223,17 +5287,17 @@
{0x09, AC_VERB_SET_CONNECT_SEL, 0x00},
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
- /* Unmute input amps (CD, Line In, Mic 1 & Mic 2) of the analog-loopback
+ /* Mute input amps (CD, Line In, Mic 1 & Mic 2) of the analog-loopback
* mixer widget
* Note: PASD motherboards uses the Line In 2 as the input for
* front panel mic (mic 2)
*/
/* Amp Indices: Mic1 = 0, Mic2 = 1, Line1 = 2, Line2 = 3, CD = 4 */
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(1)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(2)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(3)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(4)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)},
/*
* Set up output mixers (0x0c - 0x0f)
@@ -5322,6 +5386,10 @@
{ } /* end */
};
+#ifdef CONFIG_SND_HDA_POWER_SAVE
+#define alc882_loopbacks alc880_loopbacks
+#endif
+
/* pcm configuration: identiacal with ALC880 */
#define alc882_pcm_analog_playback alc880_pcm_analog_playback
#define alc882_pcm_analog_capture alc880_pcm_analog_capture
@@ -5659,6 +5727,10 @@
codec->patch_ops = alc_patch_ops;
if (board_config == ALC882_AUTO)
spec->init_hook = alc882_auto_init;
+#ifdef CONFIG_SND_HDA_POWER_SAVE
+ if (!spec->loopback.amplist)
+ spec->loopback.amplist = alc882_loopbacks;
+#endif
return 0;
}
@@ -6242,11 +6314,12 @@
{0x0f, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x0f, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(1)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(2)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(3)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(4)},
+ /* mute analog input loopbacks */
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)},
/* Front Pin: output 0 (0x0c) */
{0x14, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT},
@@ -6515,17 +6588,17 @@
{0x09, AC_VERB_SET_CONNECT_SEL, 0x00},
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
- /* Unmute input amps (CD, Line In, Mic 1 & Mic 2) of the analog-loopback
+ /* Mute input amps (CD, Line In, Mic 1 & Mic 2) of the analog-loopback
* mixer widget
* Note: PASD motherboards uses the Line In 2 as the input for
* front panel mic (mic 2)
*/
/* Amp Indices: Mic1 = 0, Mic2 = 1, Line1 = 2, Line2 = 3, CD = 4 */
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(1)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(2)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(3)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(4)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)},
/*
* Set up output mixers (0x0c - 0x0f)
@@ -6588,6 +6661,10 @@
{ } /* end */
};
+#ifdef CONFIG_SND_HDA_POWER_SAVE
+#define alc883_loopbacks alc880_loopbacks
+#endif
+
/* pcm configuration: identiacal with ALC880 */
#define alc883_pcm_analog_playback alc880_pcm_analog_playback
#define alc883_pcm_analog_capture alc880_pcm_analog_capture
@@ -7029,6 +7106,10 @@
codec->patch_ops = alc_patch_ops;
if (board_config == ALC883_AUTO)
spec->init_hook = alc883_auto_init;
+#ifdef CONFIG_SND_HDA_POWER_SAVE
+ if (!spec->loopback.amplist)
+ spec->loopback.amplist = alc883_loopbacks;
+#endif
return 0;
}
@@ -7186,17 +7267,17 @@
{0x09, AC_VERB_SET_CONNECT_SEL, 0x00},
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
- /* Unmute input amps (CD, Line In, Mic 1 & Mic 2) of the analog-loopback
+ /* Mute input amps (CD, Line In, Mic 1 & Mic 2) of the analog-loopback
* mixer widget
* Note: PASD motherboards uses the Line In 2 as the input for
* front panel mic (mic 2)
*/
/* Amp Indices: Mic1 = 0, Mic2 = 1, Line1 = 2, Line2 = 3, CD = 4 */
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(1)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(2)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(3)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(4)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)},
/*
* Set up output mixers (0x0c - 0x0e)
@@ -7565,17 +7646,17 @@
{0x09, AC_VERB_SET_CONNECT_SEL, 0x00},
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
- /* Unmute input amps (CD, Line In, Mic 1 & Mic 2) of the analog-loopback
+ /* Mute input amps (CD, Line In, Mic 1 & Mic 2) of the analog-loopback
* mixer widget
* Note: PASD motherboards uses the Line In 2 as the input for
* front panel mic (mic 2)
*/
/* Amp Indices: Mic1 = 0, Mic2 = 1, Line1 = 2, Line2 = 3, CD = 4 */
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(1)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(2)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(3)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(4)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)},
/*
* Set up output mixers (0x0c - 0x0f)
@@ -7626,19 +7707,19 @@
{0x09, AC_VERB_SET_CONNECT_SEL, 0x00},
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
- /* Unmute input amps (CD, Line In, Mic 1 & Mic 2) of the analog-loopback
+ /* Mute input amps (CD, Line In, Mic 1 & Mic 2) of the analog-loopback
* mixer widget
* Note: PASD motherboards uses the Line In 2 as the input for
* front panel mic (mic 2)
*/
/* Amp Indices: Mic1 = 0, Mic2 = 1, Line1 = 2, Line2 = 3, CD = 4 */
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(1)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(2)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(3)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(4)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(5)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(6)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(5)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(6)},
/*
* Set up output mixers (0x0c - 0x0e)
@@ -7713,20 +7794,20 @@
{0x09, AC_VERB_SET_CONNECT_SEL, 0x00},
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
- /* Unmute input amps (CD, Line In, Mic 1 & Mic 2) of the analog-loopback
+ /* Mute input amps (CD, Line In, Mic 1 & Mic 2) of the analog-loopback
* mixer widget
* Note: PASD motherboards uses the Line In 2 as the input for front
* panel mic (mic 2)
*/
/* Amp Indices: Mic1 = 0, Mic2 = 1, Line1 = 2, Line2 = 3, CD = 4 */
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(1)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(2)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(3)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(4)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(5)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(6)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(7)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(5)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(6)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(7)},
/*
* Set up output mixers (0x0c - 0x0e)
*/
@@ -7796,6 +7877,10 @@
{ }
};
+#ifdef CONFIG_SND_HDA_POWER_SAVE
+#define alc262_loopbacks alc880_loopbacks
+#endif
+
/* pcm configuration: identiacal with ALC880 */
#define alc262_pcm_analog_playback alc880_pcm_analog_playback
#define alc262_pcm_analog_capture alc880_pcm_analog_capture
@@ -8098,6 +8183,10 @@
codec->patch_ops = alc_patch_ops;
if (board_config == ALC262_AUTO)
spec->init_hook = alc262_auto_init;
+#ifdef CONFIG_SND_HDA_POWER_SAVE
+ if (!spec->loopback.amplist)
+ spec->loopback.amplist = alc262_loopbacks;
+#endif
return 0;
}
@@ -8507,6 +8596,10 @@
alc268_auto_init_analog_input(codec);
}
+#ifdef CONFIG_SND_HDA_POWER_SAVE
+#define alc883_loopbacks alc880_loopbacks
+#endif
+
/*
* configuration and preset
*/
@@ -9556,6 +9649,16 @@
alc861_auto_init_analog_input(codec);
}
+#ifdef CONFIG_SND_HDA_POWER_SAVE
+static struct hda_amp_list alc861_loopbacks[] = {
+ { 0x15, HDA_INPUT, 0 },
+ { 0x15, HDA_INPUT, 1 },
+ { 0x15, HDA_INPUT, 2 },
+ { 0x15, HDA_INPUT, 3 },
+ { } /* end */
+};
+#endif
+
/*
* configuration and preset
@@ -9753,6 +9856,10 @@
codec->patch_ops = alc_patch_ops;
if (board_config == ALC861_AUTO)
spec->init_hook = alc861_auto_init;
+#ifdef CONFIG_SND_HDA_POWER_SAVE
+ if (!spec->loopback.amplist)
+ spec->loopback.amplist = alc861_loopbacks;
+#endif
return 0;
}
@@ -10035,11 +10142,11 @@
* the analog-loopback mixer widget
*/
/* Amp Indices: Mic1 = 0, Mic2 = 1, Line1 = 2, Line2 = 3, CD = 4 */
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(1)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(2)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(3)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(4)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)},
/* Capture mixer: unmute Mic, F-Mic, Line, CD inputs */
{0x22, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
@@ -10266,6 +10373,10 @@
alc861vd_dallas_automute(codec);
}
+#ifdef CONFIG_SND_HDA_POWER_SAVE
+#define alc861vd_loopbacks alc880_loopbacks
+#endif
+
/* pcm configuration: identiacal with ALC880 */
#define alc861vd_pcm_analog_playback alc880_pcm_analog_playback
#define alc861vd_pcm_analog_capture alc880_pcm_analog_capture
@@ -10688,6 +10799,10 @@
if (board_config == ALC861VD_AUTO)
spec->init_hook = alc861vd_auto_init;
+#ifdef CONFIG_SND_HDA_POWER_SAVE
+ if (!spec->loopback.amplist)
+ spec->loopback.amplist = alc861vd_loopbacks;
+#endif
return 0;
}
@@ -10968,11 +11083,11 @@
{0x09, AC_VERB_SET_CONNECT_SEL, 0x00},
/* Front mixer: unmute input/output amp left and right (volume = 0) */
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(1)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(2)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(3)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(4)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)},
{0x02, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
{0x02, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(1)},
@@ -11041,11 +11156,11 @@
* panel mic (mic 2)
*/
/* Amp Indices: Mic1 = 0, Mic2 = 1, Line1 = 2, Line2 = 3, CD = 4 */
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(1)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(2)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(3)},
- {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(4)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)},
/*
* Set up output mixers (0x0c - 0x0f)
@@ -11132,6 +11247,10 @@
alc662_lenovo_101e_ispeaker_automute(codec);
}
+#ifdef CONFIG_SND_HDA_POWER_SAVE
+#define alc662_loopbacks alc880_loopbacks
+#endif
+
/* pcm configuration: identiacal with ALC880 */
#define alc662_pcm_analog_playback alc880_pcm_analog_playback
@@ -11534,6 +11653,10 @@
codec->patch_ops = alc_patch_ops;
if (board_config == ALC662_AUTO)
spec->init_hook = alc662_auto_init;
+#ifdef CONFIG_SND_HDA_POWER_SAVE
+ if (!spec->loopback.amplist)
+ spec->loopback.amplist = alc662_loopbacks;
+#endif
return 0;
}