config SND_BF5XX_I2S
	tristate "SoC I2S Audio for the ADI BF5xx chip"
	depends on BLACKFIN && SND_SOC
	help
	  Say Y or M if you want to add support for codecs attached to
	  the Blackfin SPORT (synchronous serial ports) interface in I2S
	  mode (supports single stereo In/Out).
	  You will also need to select the audio interfaces to support below.

config SND_BF5XX_SOC_SSM2602
	tristate "SoC SSM2602 Audio support for BF52x ezkit"
	depends on SND_BF5XX_I2S
	select SND_BF5XX_SOC_I2S
	select SND_SOC_SSM2602
	select I2C
	select I2C_BLACKFIN_TWI
	help
	  Say Y if you want to add support for SoC audio on BF527-EZKIT.

config SND_BF5XX_SOC_AD73311
	tristate "SoC AD73311 Audio support for Blackfin"
	depends on SND_BF5XX_I2S
	select SND_BF5XX_SOC_I2S
	select SND_SOC_AD73311
	help
	  Say Y if you want to add support for AD73311 codec on Blackfin.

config SND_BFIN_AD73311_SE
	int "PF pin for AD73311L Chip Select"
	depends on SND_BF5XX_SOC_AD73311
	default 4
	help
	  Enter the GPIO used to control AD73311's SE pin. Acceptable
	  values are 0 to 7

config SND_BF5XX_AC97
	tristate "SoC AC97 Audio for the ADI BF5xx chip"
	depends on BLACKFIN && SND_SOC
	help
	  Say Y or M if you want to add support for codecs attached to
	  the Blackfin SPORT (synchronous serial ports) interface in slot 16
	  mode (pseudo AC97 interface).
	  You will also need to select the audio interfaces to support below.

	  Note:
	  AC97 codecs which do not implment the slot-16 mode will not function
	  properly with this driver. This driver is known to work with the
	  Analog Devices line of AC97 codecs.

config SND_MMAP_SUPPORT
	bool "Enable MMAP Support"
	depends on SND_BF5XX_AC97
	default y
	help
	  Say y if you want AC97 driver to support mmap mode.
	  We introduce an intermediate buffer to simulate mmap.

config SND_BF5XX_SOC_SPORT
	tristate
	
config SND_BF5XX_SOC_I2S
	tristate
	select SND_BF5XX_SOC_SPORT

config SND_BF5XX_SOC_AC97
	tristate
	select AC97_BUS
	select SND_SOC_AC97_BUS
	select SND_BF5XX_SOC_SPORT

config SND_BF5XX_SOC_AD1980
	tristate "SoC AD1980/1 Audio support for BF5xx"
	depends on SND_BF5XX_AC97
	select SND_BF5XX_SOC_AC97
	select SND_SOC_AD1980
	help
	  Say Y if you want to add support for SoC audio on BF5xx STAMP/EZKIT.

config SND_BF5XX_SPORT_NUM
	int "Set a SPORT for Sound chip"
	depends on (SND_BF5XX_I2S || SND_BF5XX_AC97)
	range 0 3 if BF54x
	range 0 1 if (BF53x || BF561)
	default 0
	help
	  Set the correct SPORT for sound chip.

config SND_BF5XX_HAVE_COLD_RESET
	bool "BOARD has COLD Reset GPIO"
	depends on SND_BF5XX_AC97
	default y if BFIN548_EZKIT
	default n if !BFIN548_EZKIT
	
config SND_BF5XX_RESET_GPIO_NUM
	int "Set a GPIO for cold reset"
	depends on SND_BF5XX_HAVE_COLD_RESET
	range 0 159
	default 19 if BFIN548_EZKIT
	default 5 if BFIN537_STAMP
	help
	  Set the correct GPIO for RESET the sound chip.