[NET]: Improve presentation of networking driver families.
Suggestion from Sam Ravnborg <sam@ravnborg.org>
It causes all driver families to be displayed aligned immediately under the
main network drivers heading (in menuconfig/xconfig/gconfig) instead of
not being subordinate to (i.e., not indented) the Network device support
heading at all.
The improved network driver families are:
token ring, wireless, PCMCIA, WAN, ATM, and S390.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 534b598..51ef8a0 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -23,9 +23,12 @@
If unsure, say Y.
+# All the following symbols are dependent on NETDEVICES - do not repeat
+# that for each of the symbols.
+if NETDEVICES
+
config DUMMY
tristate "Dummy net driver support"
- depends on NETDEVICES
---help---
This is essentially a bit-bucket device (i.e. traffic you send to
this device is consigned into oblivion) with a configurable IP
@@ -45,7 +48,6 @@
config BONDING
tristate "Bonding driver support"
- depends on NETDEVICES
depends on INET
---help---
Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
@@ -63,7 +65,6 @@
config EQUALIZER
tristate "EQL (serial line load balancing) support"
- depends on NETDEVICES
---help---
If you have two serial connections to some other computer (this
usually requires two modems and two telephone lines) and you use
@@ -83,7 +84,6 @@
config TUN
tristate "Universal TUN/TAP device driver support"
- depends on NETDEVICES
select CRC32
---help---
TUN/TAP provides packet reception and transmission for user space
@@ -107,7 +107,7 @@
config NET_SB1000
tristate "General Instruments Surfboard 1000"
- depends on NETDEVICES && PNP
+ depends on PNP
---help---
This is a driver for the General Instrument (also known as
NextLevel) SURFboard 1000 internal
@@ -129,16 +129,14 @@
If you don't have this card, of course say N.
-if NETDEVICES
source "drivers/net/arcnet/Kconfig"
-endif
#
# Ethernet
#
menu "Ethernet (10 or 100Mbit)"
- depends on NETDEVICES && !UML
+ depends on !UML
config NET_ETHERNET
bool "Ethernet (10 or 100Mbit)"
@@ -1137,7 +1135,7 @@
config IBMVETH
tristate "IBM LAN Virtual Ethernet support"
- depends on NETDEVICES && NET_ETHERNET && PPC_PSERIES
+ depends on NET_ETHERNET && PPC_PSERIES
---help---
This driver supports virtual ethernet adapters on newer IBM iSeries
and pSeries systems.
@@ -1760,7 +1758,7 @@
#
menu "Ethernet (1000 Mbit)"
- depends on NETDEVICES && !UML
+ depends on !UML
config ACENIC
tristate "Alteon AceNIC/3Com 3C985/NetGear GA620 Gigabit support"
@@ -2091,7 +2089,7 @@
#
menu "Ethernet (10000 Mbit)"
- depends on NETDEVICES && !UML
+ depends on !UML
config IXGB
tristate "Intel(R) PRO/10GbE support"
@@ -2186,11 +2184,11 @@
config ISERIES_VETH
tristate "iSeries Virtual Ethernet driver support"
- depends on NETDEVICES && PPC_ISERIES
+ depends on PPC_ISERIES
config FDDI
bool "FDDI driver support"
- depends on NETDEVICES && (PCI || EISA)
+ depends on (PCI || EISA)
help
Fiber Distributed Data Interface is a high speed local area network
design; essentially a replacement for high speed Ethernet. FDDI can
@@ -2239,7 +2237,7 @@
config HIPPI
bool "HIPPI driver support (EXPERIMENTAL)"
- depends on NETDEVICES && EXPERIMENTAL && INET && PCI
+ depends on EXPERIMENTAL && INET && PCI
help
HIgh Performance Parallel Interface (HIPPI) is a 800Mbit/sec and
1600Mbit/sec dual-simplex switched or point-to-point network. HIPPI
@@ -2271,7 +2269,7 @@
config PLIP
tristate "PLIP (parallel port) support"
- depends on NETDEVICES && PARPORT
+ depends on PARPORT
---help---
PLIP (Parallel Line Internet Protocol) is used to create a
reasonably fast mini network consisting of two (or, rarely, more)
@@ -2307,7 +2305,6 @@
config PPP
tristate "PPP (point-to-point protocol) support"
- depends on NETDEVICES
---help---
PPP (Point to Point Protocol) is a newer and better SLIP. It serves
the same purpose: sending Internet traffic over telephone (and other
@@ -2443,7 +2440,6 @@
config SLIP
tristate "SLIP (serial line) support"
- depends on NETDEVICES
---help---
Say Y if you intend to use SLIP or CSLIP (compressed SLIP) to
connect to your Internet service provider or to connect to some
@@ -2510,7 +2506,7 @@
config NET_FC
bool "Fibre Channel driver support"
- depends on NETDEVICES && SCSI && PCI
+ depends on SCSI && PCI
help
Fibre Channel is a high speed serial protocol mainly used to connect
large storage devices to the computer; it is compatible with and
@@ -2523,7 +2519,7 @@
config SHAPER
tristate "Traffic Shaper (EXPERIMENTAL)"
- depends on NETDEVICES && EXPERIMENTAL
+ depends on EXPERIMENTAL
---help---
The traffic shaper is a virtual network device that allows you to
limit the rate of outgoing data flow over some other network device.
@@ -2544,11 +2540,13 @@
config NETCONSOLE
tristate "Network console logging support (EXPERIMENTAL)"
- depends on NETDEVICES && INET && EXPERIMENTAL
+ depends on INET && EXPERIMENTAL
---help---
If you want to log kernel messages over the network, enable this.
See <file:Documentation/networking/netconsole.txt> for details.
+endif #NETDEVICES
+
config NETPOLL
def_bool NETCONSOLE