diff --git a/arch/arm/configs/viper_defconfig b/arch/arm/configs/viper_defconfig
new file mode 100644
index 0000000..d01fecb
--- /dev/null
+++ b/arch/arm/configs/viper_defconfig
@@ -0,0 +1,1678 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.27-rc4
+# Thu Aug 21 17:12:07 2008
+#
+CONFIG_ARM=y
+CONFIG_HAVE_PWM=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_MMU=y
+# CONFIG_NO_IOPORT is not set
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_ARCH_SUPPORTS_AOUT=y
+CONFIG_ZONE_DMA=y
+CONFIG_ARCH_MTD_XIP=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=13
+# CONFIG_CGROUPS is not set
+# CONFIG_GROUP_SCHED is not set
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
+# CONFIG_RELAY is not set
+# CONFIG_NAMESPACES is not set
+# CONFIG_BLK_DEV_INITRD is not set
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+CONFIG_UID16=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+# CONFIG_ELF_CORE is not set
+CONFIG_COMPAT_BRK=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+# CONFIG_SHMEM is not set
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_KPROBES is not set
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
+# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+CONFIG_HAVE_CLK=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_SLABINFO=y
+CONFIG_RT_MUTEXES=y
+CONFIG_TINY_SHMEM=y
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_KMOD=y
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+# CONFIG_IOSCHED_AS is not set
+CONFIG_IOSCHED_DEADLINE=y
+# CONFIG_IOSCHED_CFQ is not set
+# CONFIG_DEFAULT_AS is not set
+CONFIG_DEFAULT_DEADLINE=y
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="deadline"
+CONFIG_CLASSIC_RCU=y
+
+#
+# System Type
+#
+# CONFIG_ARCH_AAEC2000 is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+# CONFIG_ARCH_REALVIEW is not set
+# CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_AT91 is not set
+# CONFIG_ARCH_CLPS7500 is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_NETX is not set
+# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_IMX is not set
+# CONFIG_ARCH_IOP13XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IXP23XX is not set
+# CONFIG_ARCH_IXP2000 is not set
+# CONFIG_ARCH_IXP4XX is not set
+# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_KIRKWOOD is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_MV78XX0 is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_PNX4008 is not set
+CONFIG_ARCH_PXA=y
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_SA1100 is not set
+# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_DAVINCI is not set
+# CONFIG_ARCH_OMAP is not set
+# CONFIG_ARCH_MSM7X00A is not set
+
+#
+# Intel PXA2xx/PXA3xx Implementations
+#
+# CONFIG_ARCH_GUMSTIX is not set
+# CONFIG_ARCH_LUBBOCK is not set
+# CONFIG_MACH_LOGICPD_PXA270 is not set
+# CONFIG_MACH_MAINSTONE is not set
+# CONFIG_ARCH_PXA_IDP is not set
+# CONFIG_PXA_SHARPSL is not set
+CONFIG_ARCH_VIPER=y
+# CONFIG_ARCH_PXA_ESERIES is not set
+# CONFIG_MACH_TRIZEPS4 is not set
+# CONFIG_MACH_EM_X270 is not set
+# CONFIG_MACH_COLIBRI is not set
+# CONFIG_MACH_ZYLONITE is not set
+# CONFIG_MACH_LITTLETON is not set
+# CONFIG_MACH_TAVOREVB is not set
+# CONFIG_MACH_SAAR is not set
+# CONFIG_MACH_ARMCORE is not set
+# CONFIG_MACH_MAGICIAN is not set
+# CONFIG_MACH_PCM027 is not set
+# CONFIG_ARCH_PXA_PALM is not set
+# CONFIG_PXA_EZX is not set
+CONFIG_PXA25x=y
+CONFIG_PXA_PWM=m
+CONFIG_PXA_HAVE_ISA_IRQS=y
+
+#
+# Boot options
+#
+
+#
+# Power management
+#
+
+#
+# Processor Type
+#
+CONFIG_CPU_32=y
+CONFIG_CPU_XSCALE=y
+CONFIG_CPU_32v5=y
+CONFIG_CPU_ABRT_EV5T=y
+CONFIG_CPU_PABRT_NOIFAR=y
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+
+#
+# Processor Features
+#
+CONFIG_ARM_THUMB=y
+# CONFIG_CPU_DCACHE_DISABLE is not set
+# CONFIG_OUTER_CACHE is not set
+CONFIG_IWMMXT=y
+CONFIG_XSCALE_PMU=y
+
+#
+# Bus support
+#
+CONFIG_ISA=y
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+CONFIG_PCCARD=m
+# CONFIG_PCMCIA_DEBUG is not set
+CONFIG_PCMCIA=m
+CONFIG_PCMCIA_LOAD_CIS=y
+CONFIG_PCMCIA_IOCTL=y
+
+#
+# PC-card bridges
+#
+# CONFIG_I82365 is not set
+# CONFIG_TCIC is not set
+CONFIG_PCMCIA_PXA2XX=m
+CONFIG_PCMCIA_PROBE=y
+
+#
+# Kernel Features
+#
+CONFIG_TICK_ONESHOT=y
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_PREEMPT is not set
+CONFIG_HZ=100
+CONFIG_AEABI=y
+CONFIG_OABI_COMPAT=y
+# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=4096
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+CONFIG_ALIGNMENT_TRAP=y
+
+#
+# Boot options
+#
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="root=31:02 rootfstype=jffs2 ro console=ttyS0,115200"
+# CONFIG_XIP_KERNEL is not set
+# CONFIG_KEXEC is not set
+
+#
+# CPU Frequency scaling
+#
+CONFIG_CPU_FREQ=y
+CONFIG_CPU_FREQ_TABLE=y
+# CONFIG_CPU_FREQ_DEBUG is not set
+CONFIG_CPU_FREQ_STAT=y
+# CONFIG_CPU_FREQ_STAT_DETAILS is not set
+CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
+# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
+CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
+CONFIG_CPU_FREQ_GOV_POWERSAVE=m
+CONFIG_CPU_FREQ_GOV_USERSPACE=m
+CONFIG_CPU_FREQ_GOV_ONDEMAND=m
+CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m
+CONFIG_CPU_FREQ_PXA=y
+
+#
+# Floating point emulation
+#
+
+#
+# At least one emulation must be selected
+#
+# CONFIG_FPE_NWFPE is not set
+CONFIG_FPE_FASTFPE=y
+
+#
+# Userspace binary formats
+#
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_AOUT is not set
+# CONFIG_BINFMT_MISC is not set
+
+#
+# Power management options
+#
+CONFIG_PM=y
+# CONFIG_PM_DEBUG is not set
+CONFIG_PM_SLEEP=y
+CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
+# CONFIG_APM_EMULATION is not set
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+# CONFIG_IP_PNP_BOOTP is not set
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
+# CONFIG_IRDA is not set
+CONFIG_BT=m
+CONFIG_BT_L2CAP=m
+# CONFIG_BT_SCO is not set
+CONFIG_BT_RFCOMM=m
+CONFIG_BT_RFCOMM_TTY=y
+CONFIG_BT_BNEP=m
+# CONFIG_BT_BNEP_MC_FILTER is not set
+# CONFIG_BT_BNEP_PROTO_FILTER is not set
+# CONFIG_BT_HIDP is not set
+
+#
+# Bluetooth device drivers
+#
+CONFIG_BT_HCIUSB=m
+# CONFIG_BT_HCIUSB_SCO is not set
+# CONFIG_BT_HCIBTUSB is not set
+CONFIG_BT_HCIUART=m
+CONFIG_BT_HCIUART_H4=y
+CONFIG_BT_HCIUART_BCSP=y
+# CONFIG_BT_HCIUART_LL is not set
+# CONFIG_BT_HCIBCM203X is not set
+# CONFIG_BT_HCIBPA10X is not set
+# CONFIG_BT_HCIBFUSB is not set
+# CONFIG_BT_HCIDTL1 is not set
+# CONFIG_BT_HCIBT3C is not set
+# CONFIG_BT_HCIBLUECARD is not set
+# CONFIG_BT_HCIBTUART is not set
+# CONFIG_BT_HCIVHCI is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+CONFIG_IEEE80211=m
+# CONFIG_IEEE80211_DEBUG is not set
+CONFIG_IEEE80211_CRYPT_WEP=m
+# CONFIG_IEEE80211_CRYPT_CCMP is not set
+# CONFIG_IEEE80211_CRYPT_TKIP is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+CONFIG_FW_LOADER=m
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_CONCAT is not set
+CONFIG_MTD_PARTITIONS=y
+CONFIG_MTD_REDBOOT_PARTS=y
+CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=0
+# CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set
+# CONFIG_MTD_REDBOOT_PARTS_READONLY is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+# CONFIG_MTD_AFS_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=m
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+CONFIG_MTD_JEDECPROBE=y
+CONFIG_MTD_GEN_PROBE=y
+CONFIG_MTD_CFI_ADV_OPTIONS=y
+CONFIG_MTD_CFI_NOSWAP=y
+# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set
+# CONFIG_MTD_CFI_LE_BYTE_SWAP is not set
+CONFIG_MTD_CFI_GEOMETRY=y
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+# CONFIG_MTD_MAP_BANK_WIDTH_4 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+# CONFIG_MTD_CFI_I2 is not set
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_OTP is not set
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_CFI_AMDSTD=y
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+CONFIG_MTD_RAM=y
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+# CONFIG_MTD_XIP is not set
+
+#
+# Mapping drivers for chip access
+#
+CONFIG_MTD_COMPLEX_MAPPINGS=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_PHYSMAP_START=0x8000000
+CONFIG_MTD_PHYSMAP_LEN=0
+CONFIG_MTD_PHYSMAP_BANKWIDTH=2
+CONFIG_MTD_PXA2XX=y
+# CONFIG_MTD_ARM_INTEGRATOR is not set
+# CONFIG_MTD_IMPA7 is not set
+# CONFIG_MTD_SHARP_SL is not set
+# CONFIG_MTD_PLATRAM is not set
+CONFIG_MTD_SPARSE_RAM=y
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+# CONFIG_PARPORT is not set
+# CONFIG_PNP is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=m
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_UB is not set
+# CONFIG_BLK_DEV_RAM is not set
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+CONFIG_HAVE_IDE=y
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+CONFIG_SCSI=m
+CONFIG_SCSI_DMA=y
+# CONFIG_SCSI_TGT is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_SCSI_PROC_FS is not set
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+CONFIG_BLK_DEV_SD=m
+# CONFIG_CHR_DEV_ST is not set
+# CONFIG_CHR_DEV_OSST is not set
+# CONFIG_BLK_DEV_SR is not set
+# CONFIG_CHR_DEV_SG is not set
+# CONFIG_CHR_DEV_SCH is not set
+
+#
+# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
+#
+# CONFIG_SCSI_MULTI_LUN is not set
+# CONFIG_SCSI_CONSTANTS is not set
+# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
+
+#
+# SCSI Transports
+#
+# CONFIG_SCSI_SPI_ATTRS is not set
+# CONFIG_SCSI_FC_ATTRS is not set
+# CONFIG_SCSI_ISCSI_ATTRS is not set
+# CONFIG_SCSI_SAS_LIBSAS is not set
+# CONFIG_SCSI_SRP_ATTRS is not set
+CONFIG_SCSI_LOWLEVEL=y
+# CONFIG_ISCSI_TCP is not set
+# CONFIG_SCSI_AHA152X is not set
+# CONFIG_SCSI_AIC7XXX_OLD is not set
+# CONFIG_SCSI_ADVANSYS is not set
+# CONFIG_SCSI_IN2000 is not set
+# CONFIG_SCSI_DTC3280 is not set
+# CONFIG_SCSI_FUTURE_DOMAIN is not set
+# CONFIG_SCSI_GENERIC_NCR5380 is not set
+# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set
+# CONFIG_SCSI_NCR53C406A is not set
+# CONFIG_SCSI_PAS16 is not set
+# CONFIG_SCSI_QLOGIC_FAS is not set
+# CONFIG_SCSI_SYM53C416 is not set
+# CONFIG_SCSI_T128 is not set
+# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_LOWLEVEL_PCMCIA is not set
+# CONFIG_SCSI_DH is not set
+CONFIG_ATA=m
+# CONFIG_ATA_NONSTANDARD is not set
+# CONFIG_SATA_PMP is not set
+CONFIG_ATA_SFF=y
+# CONFIG_SATA_MV is not set
+# CONFIG_PATA_LEGACY is not set
+CONFIG_PATA_PCMCIA=m
+# CONFIG_PATA_QDI is not set
+# CONFIG_PATA_WINBOND_VLB is not set
+# CONFIG_PATA_PLATFORM is not set
+# CONFIG_MD is not set
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_ARCNET is not set
+# CONFIG_PHYLIB is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_AX88796 is not set
+# CONFIG_NET_VENDOR_3COM is not set
+# CONFIG_NET_VENDOR_SMC is not set
+CONFIG_SMC91X=y
+# CONFIG_DM9000 is not set
+# CONFIG_SMC911X is not set
+# CONFIG_NET_VENDOR_RACAL is not set
+# CONFIG_AT1700 is not set
+# CONFIG_DEPCA is not set
+# CONFIG_HP100 is not set
+# CONFIG_NET_ISA is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_NET_PCI is not set
+# CONFIG_B44 is not set
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+# CONFIG_TR is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_IWLWIFI_LEDS is not set
+
+#
+# USB Network Adapters
+#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+CONFIG_USB_PEGASUS=m
+# CONFIG_USB_RTL8150 is not set
+CONFIG_USB_USBNET=m
+CONFIG_USB_NET_AX8817X=m
+CONFIG_USB_NET_CDCETHER=m
+# CONFIG_USB_NET_DM9601 is not set
+# CONFIG_USB_NET_GL620A is not set
+CONFIG_USB_NET_NET1080=m
+# CONFIG_USB_NET_PLUSB is not set
+# CONFIG_USB_NET_MCS7830 is not set
+# CONFIG_USB_NET_RNDIS_HOST is not set
+# CONFIG_USB_NET_CDC_SUBSET is not set
+CONFIG_USB_NET_ZAURUS=m
+CONFIG_NET_PCMCIA=y
+# CONFIG_PCMCIA_3C589 is not set
+# CONFIG_PCMCIA_3C574 is not set
+# CONFIG_PCMCIA_FMVJ18X is not set
+# CONFIG_PCMCIA_PCNET is not set
+# CONFIG_PCMCIA_NMCLAN is not set
+# CONFIG_PCMCIA_SMC91C92 is not set
+# CONFIG_PCMCIA_XIRC2PS is not set
+# CONFIG_PCMCIA_AXNET is not set
+# CONFIG_WAN is not set
+CONFIG_PPP=m
+# CONFIG_PPP_MULTILINK is not set
+# CONFIG_PPP_FILTER is not set
+CONFIG_PPP_ASYNC=m
+# CONFIG_PPP_SYNC_TTY is not set
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_BSDCOMP=m
+# CONFIG_PPP_MPPE is not set
+# CONFIG_PPPOE is not set
+# CONFIG_PPPOL2TP is not set
+# CONFIG_SLIP is not set
+CONFIG_SLHC=m
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=m
+# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_JOYDEV is not set
+CONFIG_INPUT_EVDEV=m
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_FUJITSU=m
+# CONFIG_TOUCHSCREEN_GUNZE is not set
+CONFIG_TOUCHSCREEN_ELO=m
+CONFIG_TOUCHSCREEN_MTOUCH=m
+CONFIG_TOUCHSCREEN_INEXIO=m
+# CONFIG_TOUCHSCREEN_MK712 is not set
+CONFIG_TOUCHSCREEN_HTCPEN=m
+CONFIG_TOUCHSCREEN_PENMOUNT=m
+CONFIG_TOUCHSCREEN_TOUCHRIGHT=m
+CONFIG_TOUCHSCREEN_TOUCHWIN=m
+# CONFIG_TOUCHSCREEN_UCB1400 is not set
+# CONFIG_TOUCHSCREEN_WM97XX is not set
+# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set
+CONFIG_TOUCHSCREEN_TOUCHIT213=m
+CONFIG_INPUT_MISC=y
+# CONFIG_INPUT_ATI_REMOTE is not set
+# CONFIG_INPUT_ATI_REMOTE2 is not set
+# CONFIG_INPUT_KEYSPAN_REMOTE is not set
+# CONFIG_INPUT_POWERMATE is not set
+# CONFIG_INPUT_YEALINK is not set
+CONFIG_INPUT_UINPUT=m
+
+#
+# Hardware I/O ports
+#
+CONFIG_SERIO=y
+CONFIG_SERIO_SERPORT=y
+# CONFIG_SERIO_LIBPS2 is not set
+# CONFIG_SERIO_RAW is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+# CONFIG_CONSOLE_TRANSLATIONS is not set
+# CONFIG_VT_CONSOLE is not set
+CONFIG_HW_CONSOLE=y
+# CONFIG_VT_HW_CONSOLE_BINDING is not set
+CONFIG_DEVKMEM=y
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=m
+# CONFIG_SERIAL_8250_CS is not set
+CONFIG_SERIAL_8250_NR_UARTS=5
+CONFIG_SERIAL_8250_RUNTIME_UARTS=5
+# CONFIG_SERIAL_8250_EXTENDED is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_PXA=y
+CONFIG_SERIAL_PXA_CONSOLE=y
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_IPMI_HANDLER is not set
+CONFIG_HW_RANDOM=m
+# CONFIG_NVRAM is not set
+# CONFIG_DTLK is not set
+# CONFIG_R3964 is not set
+
+#
+# PCMCIA character devices
+#
+# CONFIG_SYNCLINK_CS is not set
+# CONFIG_CARDMAN_4000 is not set
+# CONFIG_CARDMAN_4040 is not set
+# CONFIG_IPWIRELESS is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_DEVPORT=y
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=y
+# CONFIG_I2C_HELPER_AUTO is not set
+
+#
+# I2C Algorithms
+#
+CONFIG_I2C_ALGOBIT=y
+# CONFIG_I2C_ALGOPCF is not set
+# CONFIG_I2C_ALGOPCA is not set
+
+#
+# I2C Hardware Bus support
+#
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+CONFIG_I2C_GPIO=y
+# CONFIG_I2C_OCORES is not set
+CONFIG_I2C_PXA=y
+# CONFIG_I2C_PXA_SLAVE is not set
+# CONFIG_I2C_SIMTEC is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+# CONFIG_I2C_TINY_USB is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_ELEKTOR is not set
+# CONFIG_I2C_PCA_ISA is not set
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_DS1682 is not set
+# CONFIG_AT24 is not set
+# CONFIG_SENSORS_EEPROM is not set
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_PCF8575 is not set
+# CONFIG_SENSORS_PCA9539 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_TPS65010 is not set
+# CONFIG_SENSORS_MAX6875 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+# CONFIG_SPI is not set
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_DEBUG_GPIO is not set
+CONFIG_GPIO_SYSFS=y
+
+#
+# I2C GPIO expanders:
+#
+# CONFIG_GPIO_MAX732X is not set
+# CONFIG_GPIO_PCA953X is not set
+# CONFIG_GPIO_PCF857X is not set
+
+#
+# PCI GPIO expanders:
+#
+
+#
+# SPI GPIO expanders:
+#
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_AD7414 is not set
+# CONFIG_SENSORS_AD7418 is not set
+# CONFIG_SENSORS_ADM1021 is not set
+# CONFIG_SENSORS_ADM1025 is not set
+# CONFIG_SENSORS_ADM1026 is not set
+# CONFIG_SENSORS_ADM1029 is not set
+# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ADM9240 is not set
+# CONFIG_SENSORS_ADT7470 is not set
+# CONFIG_SENSORS_ADT7473 is not set
+# CONFIG_SENSORS_ATXP1 is not set
+# CONFIG_SENSORS_DS1621 is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_F71882FG is not set
+# CONFIG_SENSORS_F75375S is not set
+# CONFIG_SENSORS_GL518SM is not set
+# CONFIG_SENSORS_GL520SM is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_LM63 is not set
+# CONFIG_SENSORS_LM75 is not set
+# CONFIG_SENSORS_LM77 is not set
+# CONFIG_SENSORS_LM78 is not set
+# CONFIG_SENSORS_LM80 is not set
+# CONFIG_SENSORS_LM83 is not set
+# CONFIG_SENSORS_LM85 is not set
+# CONFIG_SENSORS_LM87 is not set
+# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
+# CONFIG_SENSORS_LM93 is not set
+# CONFIG_SENSORS_MAX1619 is not set
+# CONFIG_SENSORS_MAX6650 is not set
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_DME1737 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47M192 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_ADS7828 is not set
+# CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_W83781D is not set
+# CONFIG_SENSORS_W83791D is not set
+# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83793 is not set
+# CONFIG_SENSORS_W83L785TS is not set
+# CONFIG_SENSORS_W83L786NG is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+CONFIG_WATCHDOG=y
+# CONFIG_WATCHDOG_NOWAYOUT is not set
+
+#
+# Watchdog Device Drivers
+#
+# CONFIG_SOFT_WATCHDOG is not set
+# CONFIG_SA1100_WATCHDOG is not set
+
+#
+# ISA-based Watchdog Cards
+#
+# CONFIG_PCWATCHDOG is not set
+# CONFIG_MIXCOMWD is not set
+# CONFIG_WDT is not set
+
+#
+# USB-based Watchdog Cards
+#
+# CONFIG_USBPCWATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_CORE is not set
+# CONFIG_MFD_SM501 is not set
+# CONFIG_HTC_EGPIO is not set
+# CONFIG_HTC_PASIC3 is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_T7L66XB is not set
+# CONFIG_MFD_TC6387XB is not set
+# CONFIG_MFD_TC6393XB is not set
+
+#
+# Multimedia devices
+#
+
+#
+# Multimedia core support
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_VIDEO_MEDIA is not set
+
+#
+# Multimedia drivers
+#
+# CONFIG_DAB is not set
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+CONFIG_FB_CFB_FILLRECT=m
+CONFIG_FB_CFB_COPYAREA=m
+CONFIG_FB_CFB_IMAGEBLIT=m
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_S1D13XXX is not set
+CONFIG_FB_PXA=m
+# CONFIG_FB_PXA_SMARTPANEL is not set
+CONFIG_FB_PXA_PARAMETERS=y
+# CONFIG_FB_MBX is not set
+# CONFIG_FB_W100 is not set
+# CONFIG_FB_AM200EPD is not set
+# CONFIG_FB_VIRTUAL is not set
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_LCD_CLASS_DEVICE=m
+# CONFIG_LCD_ILI9320 is not set
+# CONFIG_LCD_PLATFORM is not set
+CONFIG_BACKLIGHT_CLASS_DEVICE=m
+# CONFIG_BACKLIGHT_CORGI is not set
+CONFIG_BACKLIGHT_PWM=m
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Console display driver support
+#
+# CONFIG_VGA_CONSOLE is not set
+# CONFIG_MDA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=m
+# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
+# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
+# CONFIG_FONTS is not set
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+CONFIG_LOGO=y
+CONFIG_LOGO_LINUX_MONO=y
+CONFIG_LOGO_LINUX_VGA16=y
+CONFIG_LOGO_LINUX_CLUT224=y
+CONFIG_SOUND=m
+CONFIG_SND=m
+CONFIG_SND_TIMER=m
+CONFIG_SND_PCM=m
+# CONFIG_SND_SEQUENCER is not set
+CONFIG_SND_OSSEMUL=y
+CONFIG_SND_MIXER_OSS=m
+CONFIG_SND_PCM_OSS=m
+CONFIG_SND_PCM_OSS_PLUGINS=y
+# CONFIG_SND_DYNAMIC_MINORS is not set
+CONFIG_SND_SUPPORT_OLD_API=y
+CONFIG_SND_VERBOSE_PROCFS=y
+# CONFIG_SND_VERBOSE_PRINTK is not set
+# CONFIG_SND_DEBUG is not set
+CONFIG_SND_VMASTER=y
+CONFIG_SND_AC97_CODEC=m
+CONFIG_SND_DRIVERS=y
+# CONFIG_SND_DUMMY is not set
+# CONFIG_SND_MTPAV is not set
+# CONFIG_SND_SERIAL_U16550 is not set
+# CONFIG_SND_MPU401 is not set
+# CONFIG_SND_AC97_POWER_SAVE is not set
+CONFIG_SND_ARM=y
+CONFIG_SND_PXA2XX_PCM=m
+CONFIG_SND_PXA2XX_AC97=m
+CONFIG_SND_USB=y
+# CONFIG_SND_USB_AUDIO is not set
+# CONFIG_SND_USB_CAIAQ is not set
+CONFIG_SND_PCMCIA=y
+# CONFIG_SND_VXPOCKET is not set
+# CONFIG_SND_PDAUDIOCF is not set
+# CONFIG_SND_SOC is not set
+# CONFIG_SOUND_PRIME is not set
+CONFIG_AC97_BUS=m
+CONFIG_HID_SUPPORT=y
+CONFIG_HID=y
+# CONFIG_HID_DEBUG is not set
+# CONFIG_HIDRAW is not set
+
+#
+# USB Input Devices
+#
+CONFIG_USB_HID=m
+# CONFIG_USB_HIDINPUT_POWERBOOK is not set
+# CONFIG_HID_FF is not set
+# CONFIG_USB_HIDDEV is not set
+
+#
+# USB HID Boot Protocol drivers
+#
+# CONFIG_USB_KBD is not set
+# CONFIG_USB_MOUSE is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+# CONFIG_USB_ARCH_HAS_OHCI is not set
+# CONFIG_USB_ARCH_HAS_EHCI is not set
+CONFIG_USB=m
+# CONFIG_USB_DEBUG is not set
+# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set
+
+#
+# Miscellaneous USB options
+#
+CONFIG_USB_DEVICEFS=y
+CONFIG_USB_DEVICE_CLASS=y
+# CONFIG_USB_DYNAMIC_MINORS is not set
+CONFIG_USB_SUSPEND=y
+# CONFIG_USB_OTG is not set
+# CONFIG_USB_OTG_WHITELIST is not set
+# CONFIG_USB_OTG_BLACKLIST_HUB is not set
+# CONFIG_USB_MON is not set
+
+#
+# USB Host Controller Drivers
+#
+# CONFIG_USB_C67X00_HCD is not set
+CONFIG_USB_ISP116X_HCD=m
+# CONFIG_USB_ISP1760_HCD is not set
+CONFIG_USB_SL811_HCD=m
+# CONFIG_USB_SL811_CS is not set
+CONFIG_USB_R8A66597_HCD=m
+# CONFIG_USB_MUSB_HDRC is not set
+# CONFIG_USB_GADGET_MUSB_HDRC is not set
+
+#
+# USB Device Class drivers
+#
+CONFIG_USB_ACM=m
+# CONFIG_USB_PRINTER is not set
+# CONFIG_USB_WDM is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# may also be needed; see USB_STORAGE Help for more information
+#
+CONFIG_USB_STORAGE=m
+# CONFIG_USB_STORAGE_DEBUG is not set
+# CONFIG_USB_STORAGE_DATAFAB is not set
+# CONFIG_USB_STORAGE_FREECOM is not set
+# CONFIG_USB_STORAGE_ISD200 is not set
+# CONFIG_USB_STORAGE_DPCM is not set
+# CONFIG_USB_STORAGE_USBAT is not set
+# CONFIG_USB_STORAGE_SDDR09 is not set
+# CONFIG_USB_STORAGE_SDDR55 is not set
+# CONFIG_USB_STORAGE_JUMPSHOT is not set
+# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_STORAGE_ONETOUCH is not set
+# CONFIG_USB_STORAGE_KARMA is not set
+# CONFIG_USB_STORAGE_SIERRA is not set
+# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
+# CONFIG_USB_LIBUSUAL is not set
+
+#
+# USB Imaging devices
+#
+# CONFIG_USB_MDC800 is not set
+# CONFIG_USB_MICROTEK is not set
+
+#
+# USB port drivers
+#
+CONFIG_USB_SERIAL=m
+# CONFIG_USB_EZUSB is not set
+CONFIG_USB_SERIAL_GENERIC=y
+# CONFIG_USB_SERIAL_AIRCABLE is not set
+# CONFIG_USB_SERIAL_ARK3116 is not set
+# CONFIG_USB_SERIAL_BELKIN is not set
+# CONFIG_USB_SERIAL_CH341 is not set
+# CONFIG_USB_SERIAL_WHITEHEAT is not set
+# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set
+# CONFIG_USB_SERIAL_CP2101 is not set
+# CONFIG_USB_SERIAL_CYPRESS_M8 is not set
+# CONFIG_USB_SERIAL_EMPEG is not set
+# CONFIG_USB_SERIAL_FTDI_SIO is not set
+# CONFIG_USB_SERIAL_FUNSOFT is not set
+# CONFIG_USB_SERIAL_VISOR is not set
+# CONFIG_USB_SERIAL_IPAQ is not set
+# CONFIG_USB_SERIAL_IR is not set
+# CONFIG_USB_SERIAL_EDGEPORT is not set
+# CONFIG_USB_SERIAL_EDGEPORT_TI is not set
+# CONFIG_USB_SERIAL_GARMIN is not set
+# CONFIG_USB_SERIAL_IPW is not set
+# CONFIG_USB_SERIAL_IUU is not set
+# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set
+# CONFIG_USB_SERIAL_KEYSPAN is not set
+# CONFIG_USB_SERIAL_KLSI is not set
+# CONFIG_USB_SERIAL_KOBIL_SCT is not set
+CONFIG_USB_SERIAL_MCT_U232=m
+# CONFIG_USB_SERIAL_MOS7720 is not set
+# CONFIG_USB_SERIAL_MOS7840 is not set
+# CONFIG_USB_SERIAL_MOTOROLA is not set
+# CONFIG_USB_SERIAL_NAVMAN is not set
+# CONFIG_USB_SERIAL_PL2303 is not set
+# CONFIG_USB_SERIAL_OTI6858 is not set
+# CONFIG_USB_SERIAL_SPCP8X5 is not set
+# CONFIG_USB_SERIAL_HP4X is not set
+# CONFIG_USB_SERIAL_SAFE is not set
+# CONFIG_USB_SERIAL_SIERRAWIRELESS is not set
+# CONFIG_USB_SERIAL_TI is not set
+# CONFIG_USB_SERIAL_CYBERJACK is not set
+# CONFIG_USB_SERIAL_XIRCOM is not set
+# CONFIG_USB_SERIAL_OPTION is not set
+# CONFIG_USB_SERIAL_OMNINET is not set
+# CONFIG_USB_SERIAL_DEBUG is not set
+
+#
+# USB Miscellaneous drivers
+#
+# CONFIG_USB_EMI62 is not set
+# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_ADUTUX is not set
+# CONFIG_USB_RIO500 is not set
+# CONFIG_USB_LEGOTOWER is not set
+# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
+# CONFIG_USB_LED is not set
+# CONFIG_USB_CYPRESS_CY7C63 is not set
+# CONFIG_USB_CYTHERM is not set
+# CONFIG_USB_PHIDGET is not set
+# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_FTDI_ELAN is not set
+# CONFIG_USB_APPLEDISPLAY is not set
+# CONFIG_USB_LD is not set
+# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
+# CONFIG_USB_TEST is not set
+# CONFIG_USB_ISIGHTFW is not set
+CONFIG_USB_GADGET=m
+# CONFIG_USB_GADGET_DEBUG is not set
+# CONFIG_USB_GADGET_DEBUG_FILES is not set
+CONFIG_USB_GADGET_SELECTED=y
+# CONFIG_USB_GADGET_AMD5536UDC is not set
+# CONFIG_USB_GADGET_ATMEL_USBA is not set
+# CONFIG_USB_GADGET_FSL_USB2 is not set
+# CONFIG_USB_GADGET_NET2280 is not set
+CONFIG_USB_GADGET_PXA25X=y
+CONFIG_USB_PXA25X=m
+# CONFIG_USB_PXA25X_SMALL is not set
+# CONFIG_USB_GADGET_M66592 is not set
+# CONFIG_USB_GADGET_PXA27X is not set
+# CONFIG_USB_GADGET_GOKU is not set
+# CONFIG_USB_GADGET_LH7A40X is not set
+# CONFIG_USB_GADGET_OMAP is not set
+# CONFIG_USB_GADGET_S3C2410 is not set
+# CONFIG_USB_GADGET_AT91 is not set
+# CONFIG_USB_GADGET_DUMMY_HCD is not set
+# CONFIG_USB_GADGET_DUALSPEED is not set
+# CONFIG_USB_ZERO is not set
+CONFIG_USB_ETH=m
+CONFIG_USB_ETH_RNDIS=y
+CONFIG_USB_GADGETFS=m
+CONFIG_USB_FILE_STORAGE=m
+# CONFIG_USB_FILE_STORAGE_TEST is not set
+CONFIG_USB_G_SERIAL=m
+# CONFIG_USB_MIDI_GADGET is not set
+CONFIG_USB_G_PRINTER=m
+# CONFIG_USB_CDC_COMPOSITE is not set
+# CONFIG_MMC is not set
+# CONFIG_NEW_LEDS is not set
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=m
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+CONFIG_RTC_DRV_DS1307=m
+# CONFIG_RTC_DRV_DS1374 is not set
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+# CONFIG_RTC_DRV_S35390A is not set
+# CONFIG_RTC_DRV_FM3130 is not set
+
+#
+# SPI RTC drivers
+#
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1511 is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
+CONFIG_RTC_DRV_SA1100=m
+# CONFIG_DMADEVICES is not set
+
+#
+# Voltage and Current regulators
+#
+# CONFIG_REGULATOR is not set
+# CONFIG_REGULATOR_FIXED_VOLTAGE is not set
+# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
+# CONFIG_REGULATOR_BQ24022 is not set
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=m
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=m
+# CONFIG_EXT3_FS_XATTR is not set
+# CONFIG_EXT4DEV_FS is not set
+CONFIG_JBD=m
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_DNOTIFY is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+CONFIG_FAT_FS=m
+# CONFIG_MSDOS_FS is not set
+CONFIG_VFAT_FS=m
+CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+# CONFIG_JFFS2_LZO is not set
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_V4 is not set
+CONFIG_ROOT_NFS=y
+CONFIG_NFSD=m
+CONFIG_NFSD_V3=y
+# CONFIG_NFSD_V3_ACL is not set
+# CONFIG_NFSD_V4 is not set
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_EXPORTFS=m
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_BSD_DISKLABEL is not set
+# CONFIG_MINIX_SUBPARTITION is not set
+# CONFIG_SOLARIS_X86_PARTITION is not set
+# CONFIG_UNIXWARE_DISKLABEL is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
+CONFIG_NLS=m
+CONFIG_NLS_DEFAULT="iso8859-1"
+CONFIG_NLS_CODEPAGE_437=m
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+CONFIG_NLS_CODEPAGE_850=m
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+CONFIG_NLS_ISO8859_1=m
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+CONFIG_NLS_ISO8859_15=m
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+CONFIG_NLS_UTF8=m
+# CONFIG_DLM is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
+CONFIG_SCHED_DEBUG=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_OBJECTS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+CONFIG_DEBUG_MUTEXES=y
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+CONFIG_FRAME_POINTER=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_LATENCYTOP is not set
+CONFIG_SYSCTL_SYSCALL_CHECK=y
+CONFIG_HAVE_FTRACE=y
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+# CONFIG_FTRACE is not set
+# CONFIG_IRQSOFF_TRACER is not set
+# CONFIG_SCHED_TRACER is not set
+# CONFIG_CONTEXT_SWITCH_TRACER is not set
+# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_KGDB is not set
+# CONFIG_DEBUG_USER is not set
+CONFIG_DEBUG_ERRORS=y
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_LL is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+CONFIG_CRYPTO_ALGAPI=m
+CONFIG_CRYPTO_BLKCIPHER=m
+CONFIG_CRYPTO_MANAGER=m
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+# CONFIG_CRYPTO_CBC is not set
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+CONFIG_CRYPTO_ECB=m
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+
+#
+# Digest
+#
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_MD4 is not set
+# CONFIG_CRYPTO_MD5 is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+CONFIG_CRYPTO_ARC4=m
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_DES is not set
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_LZO is not set
+CONFIG_CRYPTO_HW=y
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+# CONFIG_GENERIC_FIND_FIRST_BIT is not set
+# CONFIG_GENERIC_FIND_NEXT_BIT is not set
+CONFIG_CRC_CCITT=m
+# CONFIG_CRC16 is not set
+CONFIG_CRC_T10DIF=m
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig
index 5548abd..f781873 100644
--- a/arch/arm/mach-pxa/Kconfig
+++ b/arch/arm/mach-pxa/Kconfig
@@ -38,16 +38,19 @@
 	bool "Intel DBPXA250 Development Platform"
 	select PXA25x
 	select SA1111
+	select PXA_HAVE_BOARD_IRQS
 
 config MACH_LOGICPD_PXA270
 	bool "LogicPD PXA270 Card Engine Development Platform"
 	select PXA27x
 	select HAVE_PWM
+	select PXA_HAVE_BOARD_IRQS
 
 config MACH_MAINSTONE
 	bool "Intel HCDDBBVA0 Development Platform"
 	select PXA27x
 	select HAVE_PWM
+	select PXA_HAVE_BOARD_IRQS
 
 config MACH_MP900C
 	bool "Nec Mobilepro 900/c"
@@ -118,10 +121,21 @@
 	bool "Enable Sharp SL-6000x (Tosa) Support"
 	depends on PXA_SHARPSL
 	select PXA25x
+	select PXA_HAVE_BOARD_IRQS
+
+config ARCH_VIPER
+	bool "Arcom/Eurotech VIPER SBC"
+	select PXA25x
+	select ISA
+	select I2C_GPIO
+	select HAVE_PWM
+	select PXA_HAVE_BOARD_IRQS
+	select PXA_HAVE_ISA_IRQS
 
 config ARCH_PXA_ESERIES
 	bool "PXA based Toshiba e-series PDAs"
 	select PXA25x
+	select PXA_HAVE_BOARD_IRQS
 
 config MACH_E330
 	bool "Toshiba e330"
@@ -255,6 +269,7 @@
 	bool "Enable HTC Magician Support"
 	select PXA27x
 	select IWMMXT
+	select PXA_HAVE_BOARD_IRQS
 
 config MACH_MIOA701
 	bool "Mitac Mio A701 Support"
@@ -273,6 +288,7 @@
 	select PXA27x
 	select IWMMXT
 	select PXA_SSP
+	select PXA_HAVE_BOARD_IRQS
 
 config ARCH_PXA_PALM
 	bool "PXA based Palm PDAs"
@@ -408,4 +424,10 @@
 	  This is a simple driver that is able to control
 	  the state of built in bluetooth chip on tosa.
 
+config PXA_HAVE_BOARD_IRQS
+	bool
+
+config PXA_HAVE_ISA_IRQS
+	bool
+
 endif
diff --git a/arch/arm/mach-pxa/Makefile b/arch/arm/mach-pxa/Makefile
index 30936e40..3d2dea4 100644
--- a/arch/arm/mach-pxa/Makefile
+++ b/arch/arm/mach-pxa/Makefile
@@ -39,13 +39,16 @@
 obj-$(CONFIG_MACH_EM_X270)	+= em-x270.o
 obj-$(CONFIG_MACH_MAGICIAN)	+= magician.o
 obj-$(CONFIG_MACH_MIOA701)	+= mioa701.o mioa701_bootresume.o
-obj-$(CONFIG_ARCH_PXA_ESERIES)	+= eseries.o eseries_udc.o
-obj-$(CONFIG_MACH_E740)		+= e740_lcd.o
-obj-$(CONFIG_MACH_E750)		+= e750_lcd.o
-obj-$(CONFIG_MACH_E400)		+= e400_lcd.o
-obj-$(CONFIG_MACH_E800)		+= e800_lcd.o
+obj-$(CONFIG_ARCH_PXA_ESERIES)	+= eseries.o
+obj-$(CONFIG_MACH_E330)		+= e330.o
+obj-$(CONFIG_MACH_E350)		+= e350.o
+obj-$(CONFIG_MACH_E740)		+= e740.o
+obj-$(CONFIG_MACH_E750)		+= e750.o
+obj-$(CONFIG_MACH_E400)		+= e400.o
+obj-$(CONFIG_MACH_E800)		+= e800.o
 obj-$(CONFIG_MACH_PALMTX)	+= palmtx.o
 obj-$(CONFIG_MACH_PALMZ72)	+= palmz72.o
+obj-$(CONFIG_ARCH_VIPER)	+= viper.o
 
 ifeq ($(CONFIG_MACH_ZYLONITE),y)
   obj-y				+= zylonite.o
diff --git a/arch/arm/mach-pxa/include/mach/entry-macro.S b/arch/arm/mach-pxa/include/mach/entry-macro.S
index de16c12..f6b4bf3 100644
--- a/arch/arm/mach-pxa/include/mach/entry-macro.S
+++ b/arch/arm/mach-pxa/include/mach/entry-macro.S
@@ -41,7 +41,7 @@
 		and	\irqstat, \irqstat, \irqnr
 		clz	\irqnr, \irqstat
 		rsb	\irqnr, \irqnr, #31
-		add	\irqnr, \irqnr, #32
+		add	\irqnr, \irqnr, #(32 + PXA_IRQ(0))
 		b	1001f
 1003:
 		mrc	p6, 0, \irqstat, c0, c0, 0	@ ICIP
@@ -52,6 +52,6 @@
 		rsb	\irqstat, \irqnr, #0
 		and	\irqstat, \irqstat, \irqnr
 		clz	\irqnr, \irqstat
-		rsb	\irqnr, \irqnr, #31
+		rsb	\irqnr, \irqnr, #(31 + PXA_IRQ(0))
 1001:
 		.endm
diff --git a/arch/arm/mach-pxa/include/mach/irqs.h b/arch/arm/mach-pxa/include/mach/irqs.h
index 108b5db..9c163e1 100644
--- a/arch/arm/mach-pxa/include/mach/irqs.h
+++ b/arch/arm/mach-pxa/include/mach/irqs.h
@@ -11,7 +11,14 @@
  */
 
 
-#define PXA_IRQ(x)	(x)
+#ifdef CONFIG_PXA_HAVE_ISA_IRQS
+#define PXA_ISA_IRQ(x)	(x)
+#define PXA_ISA_IRQ_NUM	(16)
+#else
+#define PXA_ISA_IRQ_NUM	(0)
+#endif
+
+#define PXA_IRQ(x)	(PXA_ISA_IRQ_NUM + (x))
 
 #if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx)
 #define IRQ_SSP3	PXA_IRQ(0)	/* SSP3 service request */
@@ -73,7 +80,7 @@
 #define IRQ_MMC3	PXA_IRQ(55)	/* MMC3 Controller (PXA310) */
 #endif
 
-#define PXA_GPIO_IRQ_BASE	(64)
+#define PXA_GPIO_IRQ_BASE	PXA_IRQ(64)
 #define PXA_GPIO_IRQ_NUM	(128)
 
 #define GPIO_2_x_TO_IRQ(x)	(PXA_GPIO_IRQ_BASE + (x))
@@ -178,13 +185,7 @@
 #define NR_IRQS			(IRQ_S1_BVD1_STSCHG + 1)
 #elif defined(CONFIG_SHARP_LOCOMO)
 #define NR_IRQS			(IRQ_LOCOMO_SPI_TEND + 1)
-#elif defined(CONFIG_ARCH_LUBBOCK) || \
-      defined(CONFIG_MACH_LOGICPD_PXA270) || \
-      defined(CONFIG_MACH_TOSA) || \
-      defined(CONFIG_MACH_MAINSTONE) || \
-      defined(CONFIG_MACH_PCM027) || \
-      defined(CONFIG_ARCH_PXA_ESERIES) || \
-      defined(CONFIG_MACH_MAGICIAN)
+#elif defined(CONFIG_PXA_HAVE_BOARD_IRQS)
 #define NR_IRQS			(IRQ_BOARD_END)
 #elif defined(CONFIG_MACH_ZYLONITE)
 #define NR_IRQS			(IRQ_BOARD_START + 32)
diff --git a/arch/arm/mach-pxa/include/mach/viper.h b/arch/arm/mach-pxa/include/mach/viper.h
new file mode 100644
index 0000000..10988c2
--- /dev/null
+++ b/arch/arm/mach-pxa/include/mach/viper.h
@@ -0,0 +1,96 @@
+/*
+ * arch/arm/mach-pxa/include/mach/viper.h
+ *
+ * Author:	Ian Campbell
+ * Created:	Feb 03, 2003
+ * Copyright:	Arcom Control Systems.
+ *
+ * Maintained by Marc Zyngier <maz@misterjones.org>
+ *			      <marc.zyngier@altran.com>
+ *
+ * Created based on lubbock.h:
+ *  Author:	Nicolas Pitre
+ *  Created:	Jun 15, 2001
+ *  Copyright:	MontaVista Software Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef ARCH_VIPER_H
+#define ARCH_VIPER_H
+
+#define VIPER_BOOT_PHYS		PXA_CS0_PHYS
+#define VIPER_FLASH_PHYS	PXA_CS1_PHYS
+#define VIPER_ETH_PHYS		PXA_CS2_PHYS
+#define VIPER_USB_PHYS		PXA_CS3_PHYS
+#define VIPER_ETH_DATA_PHYS	PXA_CS4_PHYS
+#define VIPER_CPLD_PHYS		PXA_CS5_PHYS
+
+#define VIPER_CPLD_BASE		(0xf0000000)
+#define VIPER_PC104IO_BASE	(0xf1000000)
+#define VIPER_USB_BASE		(0xf1800000)
+
+#define VIPER_ETH_GPIO		(0)
+#define VIPER_CPLD_GPIO		(1)
+#define VIPER_USB_GPIO		(2)
+#define VIPER_UARTA_GPIO	(4)
+#define VIPER_UARTB_GPIO	(3)
+#define VIPER_CF_CD_GPIO	(32)
+#define VIPER_CF_RDY_GPIO	(8)
+#define VIPER_BCKLIGHT_EN_GPIO	(9)
+#define VIPER_LCD_EN_GPIO	(10)
+#define VIPER_PSU_DATA_GPIO	(6)
+#define VIPER_PSU_CLK_GPIO	(11)
+#define VIPER_UART_SHDN_GPIO	(12)
+#define VIPER_BRIGHTNESS_GPIO	(16)
+#define VIPER_PSU_nCS_LD_GPIO	(19)
+#define VIPER_UPS_GPIO		(20)
+#define VIPER_CF_POWER_GPIO	(82)
+#define VIPER_TPM_I2C_SDA_GPIO	(26)
+#define VIPER_TPM_I2C_SCL_GPIO	(27)
+#define VIPER_RTC_I2C_SDA_GPIO	(83)
+#define VIPER_RTC_I2C_SCL_GPIO	(84)
+
+#define VIPER_CPLD_P2V(x)	((x) - VIPER_CPLD_PHYS + VIPER_CPLD_BASE)
+#define VIPER_CPLD_V2P(x)	((x) - VIPER_CPLD_BASE + VIPER_CPLD_PHYS)
+
+#ifndef __ASSEMBLY__
+#  define __VIPER_CPLD_REG(x)	(*((volatile u16 *)VIPER_CPLD_P2V(x)))
+#endif
+
+/* board level registers in the CPLD: (offsets from CPLD_BASE) ... */
+
+/* ... Physical addresses */
+#define _VIPER_LO_IRQ_STATUS	(VIPER_CPLD_PHYS + 0x100000)
+#define _VIPER_ICR_PHYS		(VIPER_CPLD_PHYS + 0x100002)
+#define _VIPER_HI_IRQ_STATUS	(VIPER_CPLD_PHYS + 0x100004)
+#define _VIPER_VERSION_PHYS	(VIPER_CPLD_PHYS + 0x100006)
+#define VIPER_UARTA_PHYS	(VIPER_CPLD_PHYS + 0x300010)
+#define VIPER_UARTB_PHYS	(VIPER_CPLD_PHYS + 0x300000)
+#define _VIPER_SRAM_BASE	(VIPER_CPLD_PHYS + 0x800000)
+
+/* ... Virtual addresses */
+#define VIPER_LO_IRQ_STATUS	__VIPER_CPLD_REG(_VIPER_LO_IRQ_STATUS)
+#define VIPER_HI_IRQ_STATUS	__VIPER_CPLD_REG(_VIPER_HI_IRQ_STATUS)
+#define VIPER_VERSION		__VIPER_CPLD_REG(_VIPER_VERSION_PHYS)
+#define VIPER_ICR		__VIPER_CPLD_REG(_VIPER_ICR_PHYS)
+
+/* Decode VIPER_VERSION register */
+#define VIPER_CPLD_REVISION(x)	(((x) >> 5) & 0x7)
+#define VIPER_BOARD_VERSION(x)	(((x) >> 3) & 0x3)
+#define VIPER_BOARD_ISSUE(x)	(((x) >> 0) & 0x7)
+
+/* Interrupt and Configuration Register (VIPER_ICR) */
+/* This is a write only register. Only CF_RST is used under Linux */
+
+extern void viper_cf_rst(int state);
+
+#define VIPER_ICR_RETRIG	(1 << 0)
+#define VIPER_ICR_AUTO_CLR	(1 << 1)
+#define VIPER_ICR_R_DIS		(1 << 2)
+#define VIPER_ICR_CF_RST	(1 << 3)
+
+#endif
+
diff --git a/arch/arm/mach-pxa/irq.c b/arch/arm/mach-pxa/irq.c
index 5e95c53..fa69c3a 100644
--- a/arch/arm/mach-pxa/irq.c
+++ b/arch/arm/mach-pxa/irq.c
@@ -57,7 +57,7 @@
 
 	pxa_internal_irq_nr = irq_nr;
 
-	for (irq = 0; irq < irq_nr; irq += 32) {
+	for (irq = PXA_IRQ(0); irq < PXA_IRQ(irq_nr); irq += 32) {
 		_ICMR(irq) = 0;	/* disable all IRQs */
 		_ICLR(irq) = 0;	/* all IRQs are IRQ, not FIQ */
 	}
diff --git a/arch/arm/mach-pxa/viper.c b/arch/arm/mach-pxa/viper.c
new file mode 100644
index 0000000..d7632f6
--- /dev/null
+++ b/arch/arm/mach-pxa/viper.c
@@ -0,0 +1,951 @@
+/*
+ *  linux/arch/arm/mach-pxa/viper.c
+ *
+ *  Support for the Arcom VIPER SBC.
+ *
+ *  Author:	Ian Campbell
+ *  Created:    Feb 03, 2003
+ *  Copyright:  Arcom Control Systems
+ *
+ *  Maintained by Marc Zyngier <maz@misterjones.org>
+ *                             <marc.zyngier@altran.com>
+ *
+ * Based on lubbock.c:
+ *  Author:	Nicolas Pitre
+ *  Created:	Jun 15, 2001
+ *  Copyright:	MontaVista Software Inc.
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License version 2 as
+ *  published by the Free Software Foundation.
+ */
+
+#include <linux/types.h>
+#include <linux/memory.h>
+#include <linux/cpu.h>
+#include <linux/cpufreq.h>
+#include <linux/delay.h>
+#include <linux/fs.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/major.h>
+#include <linux/module.h>
+#include <linux/pm.h>
+#include <linux/sched.h>
+#include <linux/gpio.h>
+#include <linux/i2c-gpio.h>
+#include <linux/serial_8250.h>
+#include <linux/smc91x.h>
+#include <linux/pwm_backlight.h>
+#include <linux/usb/isp116x.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/bitfield.h>
+#include <mach/audio.h>
+#include <mach/pxafb.h>
+#include <mach/mfp-pxa25x.h>
+#include <mach/i2c.h>
+#include <mach/viper.h>
+
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+#include <asm/sizes.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include "generic.h"
+#include "devices.h"
+
+static unsigned int icr;
+
+static void viper_icr_set_bit(unsigned int bit)
+{
+	icr |= bit;
+	VIPER_ICR = icr;
+}
+
+static void viper_icr_clear_bit(unsigned int bit)
+{
+	icr &= ~bit;
+	VIPER_ICR = icr;
+}
+
+/* This function is used from the pcmcia module to reset the CF */
+void viper_cf_rst(int state)
+{
+	if (state)
+		viper_icr_set_bit(VIPER_ICR_CF_RST);
+	else
+		viper_icr_clear_bit(VIPER_ICR_CF_RST);
+}
+EXPORT_SYMBOL(viper_cf_rst);
+
+/*
+ * The CPLD version register was not present on VIPER boards prior to
+ * v2i1. On v1 boards where the version register is not present we
+ * will just read back the previous value from the databus.
+ *
+ * Therefore we do two reads. The first time we write 0 to the
+ * (read-only) register before reading and the second time we write
+ * 0xff first. If the two reads do not match or they read back as 0xff
+ * or 0x00 then we have version 1 hardware.
+ */
+static u8 viper_hw_version(void)
+{
+	u8 v1, v2;
+	unsigned long flags;
+
+	local_irq_save(flags);
+
+	VIPER_VERSION = 0;
+	v1 = VIPER_VERSION;
+	VIPER_VERSION = 0xff;
+	v2 = VIPER_VERSION;
+
+	v1 = (v1 != v2 || v1 == 0xff) ? 0 : v1;
+
+	local_irq_restore(flags);
+	return v1;
+}
+
+/* CPU sysdev */
+static int viper_cpu_suspend(struct sys_device *sysdev, pm_message_t state)
+{
+	viper_icr_set_bit(VIPER_ICR_R_DIS);
+	return 0;
+}
+
+static int viper_cpu_resume(struct sys_device *sysdev)
+{
+	viper_icr_clear_bit(VIPER_ICR_R_DIS);
+	return 0;
+}
+
+static struct sysdev_driver viper_cpu_sysdev_driver = {
+	.suspend	= viper_cpu_suspend,
+	.resume		= viper_cpu_resume,
+};
+
+static unsigned int current_voltage_divisor;
+
+/*
+ * If force is not true then step from existing to new divisor. If
+ * force is true then jump straight to the new divisor. Stepping is
+ * used because if the jump in voltage is too large, the VCC can dip
+ * too low and the regulator cuts out.
+ *
+ * force can be used to initialize the divisor to a know state by
+ * setting the value for the current clock speed, since we are already
+ * running at that speed we know the voltage should be pretty close so
+ * the jump won't be too large
+ */
+static void viper_set_core_cpu_voltage(unsigned long khz, int force)
+{
+	int i = 0;
+	unsigned int divisor = 0;
+	const char *v;
+
+	if (khz < 200000) {
+		v = "1.0"; divisor = 0xfff;
+	} else if (khz < 300000) {
+		v = "1.1"; divisor = 0xde5;
+	} else {
+		v = "1.3"; divisor = 0x325;
+	}
+
+	pr_debug("viper: setting CPU core voltage to %sV at %d.%03dMHz\n",
+		 v, (int)khz / 1000, (int)khz % 1000);
+
+#define STEP 0x100
+	do {
+		int step;
+
+		if (force)
+			step = divisor;
+		else if (current_voltage_divisor < divisor - STEP)
+			step = current_voltage_divisor + STEP;
+		else if (current_voltage_divisor > divisor + STEP)
+			step = current_voltage_divisor - STEP;
+		else
+			step = divisor;
+		force = 0;
+
+		gpio_set_value(VIPER_PSU_CLK_GPIO, 0);
+		gpio_set_value(VIPER_PSU_nCS_LD_GPIO, 0);
+
+		for (i = 1 << 11 ; i > 0 ; i >>= 1) {
+			udelay(1);
+
+			gpio_set_value(VIPER_PSU_DATA_GPIO, step & i);
+			udelay(1);
+
+			gpio_set_value(VIPER_PSU_CLK_GPIO, 1);
+			udelay(1);
+
+			gpio_set_value(VIPER_PSU_CLK_GPIO, 0);
+		}
+		udelay(1);
+
+		gpio_set_value(VIPER_PSU_nCS_LD_GPIO, 1);
+		udelay(1);
+
+		gpio_set_value(VIPER_PSU_nCS_LD_GPIO, 0);
+
+		current_voltage_divisor = step;
+	} while (current_voltage_divisor != divisor);
+}
+
+/* Interrupt handling */
+static unsigned long viper_irq_enabled_mask;
+
+static void viper_ack_irq(unsigned int irq)
+{
+	int viper_irq = irq - PXA_ISA_IRQ(0);
+
+	if (viper_irq < 8)
+		VIPER_LO_IRQ_STATUS = 1 << viper_irq;
+	else
+		VIPER_HI_IRQ_STATUS = 1 << (viper_irq - 8);
+}
+
+static void viper_mask_irq(unsigned int irq)
+{
+	viper_irq_enabled_mask &= ~(1 << (irq - PXA_ISA_IRQ(0)));
+}
+
+static void viper_unmask_irq(unsigned int irq)
+{
+	viper_irq_enabled_mask |= (1 << (irq - PXA_ISA_IRQ(0)));
+}
+
+static inline unsigned long viper_irq_pending(void)
+{
+	return (VIPER_HI_IRQ_STATUS << 8 | VIPER_LO_IRQ_STATUS) &
+			viper_irq_enabled_mask;
+}
+
+static void viper_irq_handler(unsigned int irq, struct irq_desc *desc)
+{
+	unsigned long pending;
+
+	pending = viper_irq_pending();
+	do {
+		if (likely(pending)) {
+			irq = PXA_ISA_IRQ(0) + __ffs(pending);
+			generic_handle_irq(irq);
+		}
+		pending = viper_irq_pending();
+	} while (pending);
+}
+
+static struct irq_chip viper_irq_chip = {
+	.name	= "ISA",
+	.ack	= viper_ack_irq,
+	.mask	= viper_mask_irq,
+	.unmask	= viper_unmask_irq
+};
+
+static void __init viper_init_irq(void)
+{
+	const int isa_irqs[] = { 3, 4, 5, 6, 7, 10, 11, 12, 9, 14, 15 };
+	int irq;
+	int isa_irq;
+
+	pxa25x_init_irq();
+
+	/* setup ISA IRQs */
+	for (irq = 0; irq < ARRAY_SIZE(isa_irqs); irq++) {
+		isa_irq = isa_irqs[irq];
+		set_irq_chip(isa_irq, &viper_irq_chip);
+		set_irq_handler(isa_irq, handle_edge_irq);
+		set_irq_flags(isa_irq, IRQF_VALID | IRQF_PROBE);
+	}
+
+	set_irq_chained_handler(gpio_to_irq(VIPER_CPLD_GPIO),
+				viper_irq_handler);
+	set_irq_type(gpio_to_irq(VIPER_CPLD_GPIO), IRQ_TYPE_EDGE_BOTH);
+
+#ifndef CONFIG_SERIAL_PXA
+	/*
+	 * 8250 doesn't support IRQ_TYPE being passed as part
+	 * of the plat_serial8250_port structure...
+	 */
+	set_irq_type(gpio_to_irq(VIPER_UARTA_GPIO), IRQ_TYPE_EDGE_RISING);
+	set_irq_type(gpio_to_irq(VIPER_UARTB_GPIO), IRQ_TYPE_EDGE_RISING);
+#endif
+}
+
+/* Flat Panel */
+static struct pxafb_mode_info fb_mode_info[] = {
+	{
+		.pixclock	= 157500,
+
+		.xres		= 320,
+		.yres		= 240,
+
+		.bpp		= 16,
+
+		.hsync_len	= 63,
+		.left_margin	= 7,
+		.right_margin	= 13,
+
+		.vsync_len	= 20,
+		.upper_margin	= 0,
+		.lower_margin	= 0,
+
+		.sync		= 0,
+	},
+};
+
+static struct pxafb_mach_info fb_info = {
+	.modes			= fb_mode_info,
+	.num_modes		= 1,
+	.lcd_conn		= LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
+};
+
+static int viper_backlight_init(struct device *dev)
+{
+	int ret;
+
+	/* GPIO9 and 10 control FB backlight. Initialise to off */
+	ret = gpio_request(VIPER_BCKLIGHT_EN_GPIO, "Backlight");
+	if (ret)
+		goto err_request_bckl;
+
+	ret = gpio_request(VIPER_LCD_EN_GPIO, "LCD");
+	if (ret)
+		goto err_request_lcd;
+
+	ret = gpio_direction_output(VIPER_BCKLIGHT_EN_GPIO, 0);
+	if (ret)
+		goto err_dir;
+
+	ret = gpio_direction_output(VIPER_LCD_EN_GPIO, 0);
+	if (ret)
+		goto err_dir;
+
+	return 0;
+
+err_dir:
+	gpio_free(VIPER_LCD_EN_GPIO);
+err_request_lcd:
+	gpio_free(VIPER_BCKLIGHT_EN_GPIO);
+err_request_bckl:
+	dev_err(dev, "Failed to setup LCD GPIOs\n");
+
+	return ret;
+}
+
+static int viper_backlight_notify(int brightness)
+{
+	gpio_set_value(VIPER_LCD_EN_GPIO, !!brightness);
+	gpio_set_value(VIPER_BCKLIGHT_EN_GPIO, !!brightness);
+
+	return brightness;
+}
+
+static void viper_backlight_exit(struct device *dev)
+{
+	gpio_free(VIPER_LCD_EN_GPIO);
+	gpio_free(VIPER_BCKLIGHT_EN_GPIO);
+}
+
+static struct platform_pwm_backlight_data viper_backlight_data = {
+	.pwm_id		= 0,
+	.max_brightness	= 100,
+	.dft_brightness	= 100,
+	.pwm_period_ns	= 1000000,
+	.init		= viper_backlight_init,
+	.notify		= viper_backlight_notify,
+	.exit		= viper_backlight_exit,
+};
+
+static struct platform_device viper_backlight_device = {
+	.name		= "pwm-backlight",
+	.dev		= {
+		.parent		= &pxa25x_device_pwm0.dev,
+		.platform_data	= &viper_backlight_data,
+	},
+};
+
+/* Ethernet */
+static struct resource smc91x_resources[] = {
+	[0] = {
+		.name	= "smc91x-regs",
+		.start  = VIPER_ETH_PHYS + 0x300,
+		.end    = VIPER_ETH_PHYS + 0x30f,
+		.flags  = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start  = gpio_to_irq(VIPER_ETH_GPIO),
+		.end    = gpio_to_irq(VIPER_ETH_GPIO),
+		.flags  = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
+	},
+	[2] = {
+		.name	= "smc91x-data32",
+		.start  = VIPER_ETH_DATA_PHYS,
+		.end    = VIPER_ETH_DATA_PHYS + 3,
+		.flags  = IORESOURCE_MEM,
+	},
+};
+
+static struct smc91x_platdata viper_smc91x_info = {
+	.flags	= SMC91X_USE_16BIT | SMC91X_NOWAIT,
+	.leda	= RPC_LED_100_10,
+	.ledb	= RPC_LED_TX_RX,
+};
+
+static struct platform_device smc91x_device = {
+	.name		= "smc91x",
+	.id		= -1,
+	.num_resources  = ARRAY_SIZE(smc91x_resources),
+	.resource       = smc91x_resources,
+	.dev		= {
+		.platform_data	= &viper_smc91x_info,
+	},
+};
+
+/* i2c */
+static struct i2c_gpio_platform_data i2c_bus_data = {
+	.sda_pin = VIPER_RTC_I2C_SDA_GPIO,
+	.scl_pin = VIPER_RTC_I2C_SCL_GPIO,
+	.udelay  = 10,
+	.timeout = 100,
+};
+
+static struct platform_device i2c_bus_device = {
+	.name		= "i2c-gpio",
+	.id		= 1, /* pxa2xx-i2c is bus 0, so start at 1 */
+	.dev = {
+		.platform_data = &i2c_bus_data,
+	}
+};
+
+static struct i2c_board_info __initdata viper_i2c_devices[] = {
+	{
+		I2C_BOARD_INFO("ds1338", 0x68),
+	},
+};
+
+/*
+ * Serial configuration:
+ * You can either have the standard PXA ports driven by the PXA driver,
+ * or all the ports (PXA + 16850) driven by the 8250 driver.
+ * Choose your poison.
+ */
+
+static struct resource viper_serial_resources[] = {
+#ifndef CONFIG_SERIAL_PXA
+	{
+		.start	= 0x40100000,
+		.end	= 0x4010001f,
+		.flags	= IORESOURCE_MEM,
+	},
+	{
+		.start	= 0x40200000,
+		.end	= 0x4020001f,
+		.flags	= IORESOURCE_MEM,
+	},
+	{
+		.start	= 0x40700000,
+		.end	= 0x4070001f,
+		.flags	= IORESOURCE_MEM,
+	},
+	{
+		.start	= VIPER_UARTA_PHYS,
+		.end	= VIPER_UARTA_PHYS + 0xf,
+		.flags	= IORESOURCE_MEM,
+	},
+	{
+		.start	= VIPER_UARTB_PHYS,
+		.end	= VIPER_UARTB_PHYS + 0xf,
+		.flags	= IORESOURCE_MEM,
+	},
+#else
+	{
+		0,
+	},
+#endif
+};
+
+static struct plat_serial8250_port serial_platform_data[] = {
+#ifndef CONFIG_SERIAL_PXA
+	/* Internal UARTs */
+	{
+		.membase	= (void *)&FFUART,
+		.mapbase	= __PREG(FFUART),
+		.irq		= IRQ_FFUART,
+		.uartclk	= 921600 * 16,
+		.regshift	= 2,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+	},
+	{
+		.membase	= (void *)&BTUART,
+		.mapbase	= __PREG(BTUART),
+		.irq		= IRQ_BTUART,
+		.uartclk	= 921600 * 16,
+		.regshift	= 2,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+	},
+	{
+		.membase	= (void *)&STUART,
+		.mapbase	= __PREG(STUART),
+		.irq		= IRQ_STUART,
+		.uartclk	= 921600 * 16,
+		.regshift	= 2,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+	},
+	/* External UARTs */
+	{
+		.mapbase	= VIPER_UARTA_PHYS,
+		.irq		= gpio_to_irq(VIPER_UARTA_GPIO),
+		.uartclk	= 1843200,
+		.regshift	= 1,
+		.iotype		= UPIO_MEM,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_IOREMAP |
+				  UPF_SKIP_TEST,
+	},
+	{
+		.mapbase	= VIPER_UARTB_PHYS,
+		.irq		= gpio_to_irq(VIPER_UARTB_GPIO),
+		.uartclk	= 1843200,
+		.regshift	= 1,
+		.iotype		= UPIO_MEM,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_IOREMAP |
+				  UPF_SKIP_TEST,
+	},
+#endif
+	{ },
+};
+
+static struct platform_device serial_device = {
+	.name			= "serial8250",
+	.id			= 0,
+	.dev			= {
+		.platform_data	= serial_platform_data,
+	},
+	.num_resources		= ARRAY_SIZE(viper_serial_resources),
+	.resource		= viper_serial_resources,
+};
+
+/* USB */
+static void isp116x_delay(struct device *dev, int delay)
+{
+	ndelay(delay);
+}
+
+static struct resource isp116x_resources[] = {
+	[0] = { /* DATA */
+		.start  = VIPER_USB_PHYS + 0,
+		.end    = VIPER_USB_PHYS + 1,
+		.flags  = IORESOURCE_MEM,
+	},
+	[1] = { /* ADDR */
+		.start  = VIPER_USB_PHYS + 2,
+		.end    = VIPER_USB_PHYS + 3,
+		.flags  = IORESOURCE_MEM,
+	},
+	[2] = {
+		.start  = gpio_to_irq(VIPER_USB_GPIO),
+		.end    = gpio_to_irq(VIPER_USB_GPIO),
+		.flags  = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
+	},
+};
+
+/* (DataBusWidth16|AnalogOCEnable|DREQOutputPolarity|DownstreamPort15KRSel ) */
+static struct isp116x_platform_data isp116x_platform_data = {
+	/* Enable internal resistors on downstream ports */
+	.sel15Kres		= 1,
+	/* On-chip overcurrent protection */
+	.oc_enable		= 1,
+	/* INT output polarity */
+	.int_act_high		= 1,
+	/* INT edge or level triggered */
+	.int_edge_triggered	= 0,
+
+	/* WAKEUP pin connected - NOT SUPPORTED  */
+	/* .remote_wakeup_connected = 0, */
+	/* Wakeup by devices on usb bus enabled */
+	.remote_wakeup_enable	= 0,
+	.delay			= isp116x_delay,
+};
+
+static struct platform_device isp116x_device = {
+	.name			= "isp116x-hcd",
+	.id			= -1,
+	.num_resources  	= ARRAY_SIZE(isp116x_resources),
+	.resource       	= isp116x_resources,
+	.dev			= {
+		.platform_data	= &isp116x_platform_data,
+	},
+
+};
+
+/* MTD */
+static struct resource mtd_resources[] = {
+	[0] = {	/* RedBoot config + filesystem flash */
+		.start	= VIPER_FLASH_PHYS,
+		.end	= VIPER_FLASH_PHYS + SZ_32M - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {	/* Boot flash */
+		.start	= VIPER_BOOT_PHYS,
+		.end	= VIPER_BOOT_PHYS + SZ_1M - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[2] = { /*
+		 * SRAM size is actually 256KB, 8bits, with a sparse mapping
+		 * (each byte is on a 16bit boundary).
+		 */
+		.start	= _VIPER_SRAM_BASE,
+		.end	= _VIPER_SRAM_BASE + SZ_512K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct mtd_partition viper_boot_flash_partition = {
+	.name		= "RedBoot",
+	.size		= SZ_1M,
+	.offset		= 0,
+	.mask_flags	= MTD_WRITEABLE,	/* force R/O */
+};
+
+static struct physmap_flash_data viper_flash_data[] = {
+	[0] = {
+		.width		= 2,
+		.parts		= NULL,
+		.nr_parts	= 0,
+	},
+	[1] = {
+		.width		= 2,
+		.parts		= &viper_boot_flash_partition,
+		.nr_parts	= 1,
+	},
+};
+
+static struct platform_device viper_mtd_devices[] = {
+	[0] = {
+		.name		= "physmap-flash",
+		.id		= 0,
+		.dev		= {
+			.platform_data	= &viper_flash_data[0],
+		},
+		.resource	= &mtd_resources[0],
+		.num_resources	= 1,
+	},
+	[1] = {
+		.name		= "physmap-flash",
+		.id		= 1,
+		.dev		= {
+			.platform_data	= &viper_flash_data[1],
+		},
+		.resource	= &mtd_resources[1],
+		.num_resources	= 1,
+	},
+};
+
+static struct platform_device *viper_devs[] __initdata = {
+	&smc91x_device,
+	&i2c_bus_device,
+	&serial_device,
+	&isp116x_device,
+	&viper_mtd_devices[0],
+	&viper_mtd_devices[1],
+	&viper_backlight_device,
+};
+
+static mfp_cfg_t viper_pin_config[] __initdata = {
+	/* Chip selects */
+	GPIO15_nCS_1,
+	GPIO78_nCS_2,
+	GPIO79_nCS_3,
+	GPIO80_nCS_4,
+	GPIO33_nCS_5,
+
+	/* FP Backlight */
+	GPIO9_GPIO, 				/* VIPER_BCKLIGHT_EN_GPIO */
+	GPIO10_GPIO,				/* VIPER_LCD_EN_GPIO */
+	GPIO16_PWM0_OUT,
+
+	/* Ethernet PHY Ready */
+	GPIO18_RDY,
+
+	/* Serial shutdown */
+	GPIO12_GPIO | MFP_LPM_DRIVE_HIGH,	/* VIPER_UART_SHDN_GPIO */
+
+	/* Compact-Flash / PC104 */
+	GPIO48_nPOE,
+	GPIO49_nPWE,
+	GPIO50_nPIOR,
+	GPIO51_nPIOW,
+	GPIO52_nPCE_1,
+	GPIO53_nPCE_2,
+	GPIO54_nPSKTSEL,
+	GPIO55_nPREG,
+	GPIO56_nPWAIT,
+	GPIO57_nIOIS16,
+	GPIO8_GPIO,				/* VIPER_CF_RDY_GPIO */
+	GPIO32_GPIO,				/* VIPER_CF_CD_GPIO */
+	GPIO82_GPIO,				/* VIPER_CF_POWER_GPIO */
+
+	/* Integrated UPS control */
+	GPIO20_GPIO,				/* VIPER_UPS_GPIO */
+
+	/* Vcc regulator control */
+	GPIO6_GPIO,				/* VIPER_PSU_DATA_GPIO */
+	GPIO11_GPIO,				/* VIPER_PSU_CLK_GPIO */
+	GPIO19_GPIO,				/* VIPER_PSU_nCS_LD_GPIO */
+
+	/* i2c busses */
+	GPIO26_GPIO,				/* VIPER_TPM_I2C_SDA_GPIO */
+	GPIO27_GPIO,				/* VIPER_TPM_I2C_SCL_GPIO */
+	GPIO83_GPIO,				/* VIPER_RTC_I2C_SDA_GPIO */
+	GPIO84_GPIO,				/* VIPER_RTC_I2C_SCL_GPIO */
+
+	/* PC/104 Interrupt */
+	GPIO1_GPIO | WAKEUP_ON_EDGE_RISE,	/* VIPER_CPLD_GPIO */
+};
+
+static unsigned long viper_tpm;
+
+static int __init viper_tpm_setup(char *str)
+{
+	strict_strtoul(str, 10, &viper_tpm);
+	return 1;
+}
+
+__setup("tpm=", viper_tpm_setup);
+
+static void __init viper_tpm_init(void)
+{
+	struct platform_device *tpm_device;
+	struct i2c_gpio_platform_data i2c_tpm_data = {
+		.sda_pin = VIPER_TPM_I2C_SDA_GPIO,
+		.scl_pin = VIPER_TPM_I2C_SCL_GPIO,
+		.udelay  = 10,
+		.timeout = 100,
+	};
+	char *errstr;
+
+	/* Allocate TPM i2c bus if requested */
+	if (!viper_tpm)
+		return;
+
+	tpm_device = platform_device_alloc("i2c-gpio", 2);
+	if (tpm_device) {
+		if (!platform_device_add_data(tpm_device,
+					      &i2c_tpm_data,
+					      sizeof(i2c_tpm_data))) {
+			if (platform_device_add(tpm_device)) {
+				errstr = "register TPM i2c bus";
+				goto error_free_tpm;
+			}
+		} else {
+			errstr = "allocate TPM i2c bus data";
+			goto error_free_tpm;
+		}
+	} else {
+		errstr = "allocate TPM i2c device";
+		goto error_tpm;
+	}
+
+	return;
+
+error_free_tpm:
+	kfree(tpm_device);
+error_tpm:
+	pr_err("viper: Couldn't %s, giving up\n", errstr);
+}
+
+static void __init viper_init_vcore_gpios(void)
+{
+	if (gpio_request(VIPER_PSU_DATA_GPIO, "PSU data"))
+		goto err_request_data;
+
+	if (gpio_request(VIPER_PSU_CLK_GPIO, "PSU clock"))
+		goto err_request_clk;
+
+	if (gpio_request(VIPER_PSU_nCS_LD_GPIO, "PSU cs"))
+		goto err_request_cs;
+
+	if (gpio_direction_output(VIPER_PSU_DATA_GPIO, 0) ||
+	    gpio_direction_output(VIPER_PSU_CLK_GPIO, 0) ||
+	    gpio_direction_output(VIPER_PSU_nCS_LD_GPIO, 0))
+		goto err_dir;
+
+	/* c/should assume redboot set the correct level ??? */
+	viper_set_core_cpu_voltage(get_clk_frequency_khz(0), 1);
+
+	return;
+
+err_dir:
+	gpio_free(VIPER_PSU_nCS_LD_GPIO);
+err_request_cs:
+	gpio_free(VIPER_PSU_CLK_GPIO);
+err_request_clk:
+	gpio_free(VIPER_PSU_DATA_GPIO);
+err_request_data:
+	pr_err("viper: Failed to setup vcore control GPIOs\n");
+}
+
+static void __init viper_init_serial_gpio(void)
+{
+	if (gpio_request(VIPER_UART_SHDN_GPIO, "UARTs shutdown"))
+		goto err_request;
+
+	if (gpio_direction_output(VIPER_UART_SHDN_GPIO, 0))
+		goto err_dir;
+
+	return;
+
+err_dir:
+	gpio_free(VIPER_UART_SHDN_GPIO);
+err_request:
+	pr_err("viper: Failed to setup UART shutdown GPIO\n");
+}
+
+#ifdef CONFIG_CPU_FREQ
+static int viper_cpufreq_notifier(struct notifier_block *nb,
+				  unsigned long val, void *data)
+{
+	struct cpufreq_freqs *freq = data;
+
+	/* TODO: Adjust timings??? */
+
+	switch (val) {
+	case CPUFREQ_PRECHANGE:
+		if (freq->old < freq->new) {
+			/* we are getting faster so raise the voltage
+			 * before we change freq */
+			viper_set_core_cpu_voltage(freq->new, 0);
+		}
+		break;
+	case CPUFREQ_POSTCHANGE:
+		if (freq->old > freq->new) {
+			/* we are slowing down so drop the power
+			 * after we change freq */
+			viper_set_core_cpu_voltage(freq->new, 0);
+		}
+		break;
+	case CPUFREQ_RESUMECHANGE:
+		viper_set_core_cpu_voltage(freq->new, 0);
+		break;
+	default:
+		/* ignore */
+		break;
+	}
+
+	return 0;
+}
+
+static struct notifier_block viper_cpufreq_notifier_block = {
+	.notifier_call  = viper_cpufreq_notifier
+};
+
+static void __init viper_init_cpufreq(void)
+{
+	if (cpufreq_register_notifier(&viper_cpufreq_notifier_block,
+				      CPUFREQ_TRANSITION_NOTIFIER))
+		pr_err("viper: Failed to setup cpufreq notifier\n");
+}
+#else
+static inline void viper_init_cpufreq(void) {}
+#endif
+
+static void viper_power_off(void)
+{
+	pr_notice("Shutting off UPS\n");
+	gpio_set_value(VIPER_UPS_GPIO, 1);
+	/* Spin to death... */
+	while (1);
+}
+
+static void __init viper_init(void)
+{
+	u8 version;
+
+	pm_power_off = viper_power_off;
+
+	pxa2xx_mfp_config(ARRAY_AND_SIZE(viper_pin_config));
+
+	/* Wake-up serial console */
+	viper_init_serial_gpio();
+
+	set_pxa_fb_info(&fb_info);
+
+	/* v1 hardware cannot use the datacs line */
+	version = viper_hw_version();
+	if (version == 0)
+		smc91x_device.num_resources--;
+
+	pxa_set_i2c_info(NULL);
+	platform_add_devices(viper_devs, ARRAY_SIZE(viper_devs));
+
+	viper_init_vcore_gpios();
+	viper_init_cpufreq();
+
+	sysdev_driver_register(&cpu_sysdev_class, &viper_cpu_sysdev_driver);
+
+	if (version) {
+		pr_info("viper: hardware v%di%d detected. "
+			"CPLD revision %d.\n",
+			VIPER_BOARD_VERSION(version),
+			VIPER_BOARD_ISSUE(version),
+			VIPER_CPLD_REVISION(version));
+		system_rev = (VIPER_BOARD_VERSION(version) << 8) |
+			     (VIPER_BOARD_ISSUE(version) << 4) |
+			     VIPER_CPLD_REVISION(version);
+	} else {
+		pr_info("viper: No version register.\n");
+	}
+
+	i2c_register_board_info(1, ARRAY_AND_SIZE(viper_i2c_devices));
+
+	viper_tpm_init();
+	pxa_set_ac97_info(NULL);
+}
+
+static struct map_desc viper_io_desc[] __initdata = {
+	{
+		.virtual = VIPER_CPLD_BASE,
+		.pfn     = __phys_to_pfn(VIPER_CPLD_PHYS),
+		.length  = 0x00300000,
+		.type    = MT_DEVICE,
+	},
+	{
+		.virtual = VIPER_PC104IO_BASE,
+		.pfn     = __phys_to_pfn(_PCMCIA1IO),
+		.length  = 0x00800000,
+		.type    = MT_DEVICE,
+	},
+};
+
+static void __init viper_map_io(void)
+{
+	pxa_map_io();
+
+	iotable_init(viper_io_desc, ARRAY_SIZE(viper_io_desc));
+
+	PCFR |= PCFR_OPDE;
+}
+
+MACHINE_START(VIPER, "Arcom/Eurotech VIPER SBC")
+	/* Maintainer: Marc Zyngier <maz@misterjones.org> */
+	.phys_io	= 0x40000000,
+	.io_pg_offst	= (io_p2v(0x40000000) >> 18) & 0xfffc,
+	.boot_params	= 0xa0000100,
+	.map_io		= viper_map_io,
+	.init_irq	= viper_init_irq,
+	.timer          = &pxa_timer,
+	.init_machine	= viper_init,
+MACHINE_END
diff --git a/drivers/net/smc91x.c b/drivers/net/smc91x.c
index 24768c1..e332a51 100644
--- a/drivers/net/smc91x.c
+++ b/drivers/net/smc91x.c
@@ -1520,7 +1520,9 @@
 	/* Setup the default Register Modes */
 	lp->tcr_cur_mode = TCR_DEFAULT;
 	lp->rcr_cur_mode = RCR_DEFAULT;
-	lp->rpc_cur_mode = RPC_DEFAULT;
+	lp->rpc_cur_mode = RPC_DEFAULT |
+				lp->cfg.leda << RPC_LSXA_SHFT |
+				lp->cfg.ledb << RPC_LSXB_SHFT;
 
 	/*
 	 * If we are not using a MII interface, we need to
@@ -2157,6 +2159,11 @@
 		lp->cfg.flags |= (nowait) ? SMC91X_NOWAIT : 0;
 	}
 
+	if (!lp->cfg.leda && !lp->cfg.ledb) {
+		lp->cfg.leda = RPC_LSA_DEFAULT;
+		lp->cfg.ledb = RPC_LSB_DEFAULT;
+	}
+
 	ndev->dma = (unsigned char)-1;
 
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "smc91x-regs");
diff --git a/drivers/net/smc91x.h b/drivers/net/smc91x.h
index 997e7f1..160873f 100644
--- a/drivers/net/smc91x.h
+++ b/drivers/net/smc91x.h
@@ -43,7 +43,8 @@
 #if defined(CONFIG_ARCH_LUBBOCK) ||\
     defined(CONFIG_MACH_MAINSTONE) ||\
     defined(CONFIG_MACH_ZYLONITE) ||\
-    defined(CONFIG_MACH_LITTLETON)
+    defined(CONFIG_MACH_LITTLETON) ||\
+    defined(CONFIG_ARCH_VIPER)
 
 #include <asm/mach-types.h>
 
@@ -778,14 +779,6 @@
 #define RPC_ANEG	0x0800	// When 1 PHY is in Auto-Negotiate Mode
 #define RPC_LSXA_SHFT	5	// Bits to shift LS2A,LS1A,LS0A to lsb
 #define RPC_LSXB_SHFT	2	// Bits to get LS2B,LS1B,LS0B to lsb
-#define RPC_LED_100_10	(0x00)	// LED = 100Mbps OR's with 10Mbps link detect
-#define RPC_LED_RES	(0x01)	// LED = Reserved
-#define RPC_LED_10	(0x02)	// LED = 10Mbps link detect
-#define RPC_LED_FD	(0x03)	// LED = Full Duplex Mode
-#define RPC_LED_TX_RX	(0x04)	// LED = TX or RX packet occurred
-#define RPC_LED_100	(0x05)	// LED = 100Mbps link dectect
-#define RPC_LED_TX	(0x06)	// LED = TX packet occurred
-#define RPC_LED_RX	(0x07)	// LED = RX packet occurred
 
 #ifndef RPC_LSA_DEFAULT
 #define RPC_LSA_DEFAULT	RPC_LED_100
@@ -794,7 +787,7 @@
 #define RPC_LSB_DEFAULT RPC_LED_FD
 #endif
 
-#define RPC_DEFAULT (RPC_ANEG | (RPC_LSA_DEFAULT << RPC_LSXA_SHFT) | (RPC_LSB_DEFAULT << RPC_LSXB_SHFT) | RPC_SPEED | RPC_DPLX)
+#define RPC_DEFAULT (RPC_ANEG | RPC_SPEED | RPC_DPLX)
 
 
 /* Bank 0 0x0C is reserved */
diff --git a/drivers/pcmcia/Kconfig b/drivers/pcmcia/Kconfig
index 40417d3..f57eeae 100644
--- a/drivers/pcmcia/Kconfig
+++ b/drivers/pcmcia/Kconfig
@@ -220,7 +220,8 @@
 	tristate "PXA2xx support"
 	depends on ARM && ARCH_PXA && PCMCIA
 	depends on (ARCH_LUBBOCK || MACH_MAINSTONE || PXA_SHARPSL \
-		    || MACH_ARMCORE || ARCH_PXA_PALM || TRIZEPS_PCMCIA)
+		    || MACH_ARMCORE || ARCH_PXA_PALM || TRIZEPS_PCMCIA \
+		    || ARCH_VIPER)
 	help
 	  Say Y here to include support for the PXA2xx PCMCIA controller
 
diff --git a/drivers/pcmcia/Makefile b/drivers/pcmcia/Makefile
index 679ca92..8c2fe94 100644
--- a/drivers/pcmcia/Makefile
+++ b/drivers/pcmcia/Makefile
@@ -72,7 +72,7 @@
 pxa2xx_cs-$(CONFIG_MACH_MAINSTONE)		+= pxa2xx_mainstone.o
 pxa2xx_cs-$(CONFIG_PXA_SHARPSL)			+= pxa2xx_sharpsl.o
 pxa2xx_cs-$(CONFIG_MACH_ARMCORE)		+= pxa2xx_cm_x2xx.o pxa2xx_cm_x255.o pxa2xx_cm_x270.o
+pxa2xx_cs-$(CONFIG_ARCH_VIPER)			+= pxa2xx_viper.o
 pxa2xx_cs-$(CONFIG_TRIZEPS_PCMCIA)		+= pxa2xx_trizeps.o
 pxa2xx_cs-$(CONFIG_MACH_PALMTX)			+= pxa2xx_palmtx.o
 pxa2xx_cs-$(CONFIG_MACH_PALMLD)			+= pxa2xx_palmld.o
-
diff --git a/drivers/pcmcia/pxa2xx_base.c b/drivers/pcmcia/pxa2xx_base.c
index 1b07af5..13f1e0f 100644
--- a/drivers/pcmcia/pxa2xx_base.c
+++ b/drivers/pcmcia/pxa2xx_base.c
@@ -30,6 +30,7 @@
 #include <asm/system.h>
 #include <mach/pxa-regs.h>
 #include <mach/pxa2xx-regs.h>
+#include <asm/mach-types.h>
 
 #include <pcmcia/cs_types.h>
 #include <pcmcia/ss.h>
@@ -166,18 +167,32 @@
 }
 #endif
 
+static void pxa2xx_configure_sockets(struct device *dev)
+{
+	struct pcmcia_low_level *ops = dev->platform_data;
+
+	/*
+	 * We have at least one socket, so set MECR:CIT
+	 * (Card Is There)
+	 */
+	MECR |= MECR_CIT;
+
+	/* Set MECR:NOS (Number Of Sockets) */
+	if (ops->nr > 1 || machine_is_viper())
+		MECR |= MECR_NOS;
+	else
+		MECR &= ~MECR_NOS;
+}
+
 int __pxa2xx_drv_pcmcia_probe(struct device *dev)
 {
 	int ret;
 	struct pcmcia_low_level *ops;
-	int first, nr;
 
 	if (!dev || !dev->platform_data)
 		return -ENODEV;
 
 	ops = (struct pcmcia_low_level *)dev->platform_data;
-	first = ops->first;
-	nr = ops->nr;
 
 	/* Provide our PXA2xx specific timing routines. */
 	ops->set_timing  = pxa2xx_pcmcia_set_timing;
@@ -185,21 +200,10 @@
 	ops->frequency_change = pxa2xx_pcmcia_frequency_change;
 #endif
 
-	ret = soc_common_drv_pcmcia_probe(dev, ops, first, nr);
+	ret = soc_common_drv_pcmcia_probe(dev, ops, ops->first, ops->nr);
 
-	if (ret == 0) {
-		/*
-		 * We have at least one socket, so set MECR:CIT
-		 * (Card Is There)
-		 */
-		MECR |= MECR_CIT;
-
-		/* Set MECR:NOS (Number Of Sockets) */
-		if (nr > 1)
-			MECR |= MECR_NOS;
-		else
-			MECR &= ~MECR_NOS;
-	}
+	if (!ret)
+		pxa2xx_configure_sockets(dev);
 
 	return ret;
 }
@@ -223,11 +227,7 @@
 
 static int pxa2xx_drv_pcmcia_resume(struct platform_device *dev)
 {
-	struct pcmcia_low_level *ops = dev->dev.platform_data;
-	int nr = ops ? ops->nr : 0;
-
-	MECR = nr > 1 ? MECR_CIT | MECR_NOS : (nr > 0 ? MECR_CIT : 0);
-
+	pxa2xx_configure_sockets(&dev->dev);
 	return pcmcia_socket_dev_resume(&dev->dev);
 }
 
diff --git a/drivers/pcmcia/pxa2xx_viper.c b/drivers/pcmcia/pxa2xx_viper.c
new file mode 100644
index 0000000..dd10481
--- /dev/null
+++ b/drivers/pcmcia/pxa2xx_viper.c
@@ -0,0 +1,179 @@
+/*
+ * VIPER PCMCIA support
+ *   Copyright 2004 Arcom Control Systems
+ *
+ * Maintained by Marc Zyngier <maz@misterjones.org>
+ * 			      <marc.zyngier@altran.com>
+ *
+ * Based on:
+ *   iPAQ h2200 PCMCIA support
+ *   Copyright 2004 Koen Kooi <koen@vestingbar.nl>
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file COPYING in the main directory of this archive for
+ * more details.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+
+#include <pcmcia/ss.h>
+
+#include <asm/irq.h>
+
+#include <mach/pxa-regs.h>
+#include <mach/viper.h>
+#include <asm/mach-types.h>
+
+#include "soc_common.h"
+#include "pxa2xx_base.h"
+
+static struct pcmcia_irqs irqs[] = {
+	{ 0, gpio_to_irq(VIPER_CF_CD_GPIO),  "PCMCIA_CD" }
+};
+
+static int viper_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
+{
+	unsigned long flags;
+
+	skt->irq = gpio_to_irq(VIPER_CF_RDY_GPIO);
+
+	if (gpio_request(VIPER_CF_CD_GPIO, "CF detect"))
+		goto err_request_cd;
+
+	if (gpio_request(VIPER_CF_RDY_GPIO, "CF ready"))
+		goto err_request_rdy;
+
+	if (gpio_request(VIPER_CF_POWER_GPIO, "CF power"))
+		goto err_request_pwr;
+
+	local_irq_save(flags);
+
+	/* GPIO 82 is the CF power enable line. initially off */
+	if (gpio_direction_output(VIPER_CF_POWER_GPIO, 0) ||
+	    gpio_direction_input(VIPER_CF_CD_GPIO) ||
+	    gpio_direction_input(VIPER_CF_RDY_GPIO)) {
+		local_irq_restore(flags);
+		goto err_dir;
+	}
+
+	local_irq_restore(flags);
+
+	return soc_pcmcia_request_irqs(skt, irqs, ARRAY_SIZE(irqs));
+
+err_dir:
+	gpio_free(VIPER_CF_POWER_GPIO);
+err_request_pwr:
+	gpio_free(VIPER_CF_RDY_GPIO);
+err_request_rdy:
+	gpio_free(VIPER_CF_CD_GPIO);
+err_request_cd:
+	printk(KERN_ERR "viper: Failed to setup PCMCIA GPIOs\n");
+	return -1;
+}
+
+/*
+ * Release all resources.
+ */
+static void viper_pcmcia_hw_shutdown(struct soc_pcmcia_socket *skt)
+{
+	soc_pcmcia_free_irqs(skt, irqs, ARRAY_SIZE(irqs));
+	gpio_free(VIPER_CF_POWER_GPIO);
+	gpio_free(VIPER_CF_RDY_GPIO);
+	gpio_free(VIPER_CF_CD_GPIO);
+}
+
+static void viper_pcmcia_socket_state(struct soc_pcmcia_socket *skt,
+				      struct pcmcia_state *state)
+{
+	state->detect = gpio_get_value(VIPER_CF_CD_GPIO) ? 0 : 1;
+	state->ready  = gpio_get_value(VIPER_CF_RDY_GPIO) ? 1 : 0;
+	state->bvd1   = 1;
+	state->bvd2   = 1;
+	state->wrprot = 0;
+	state->vs_3v  = 1; /* Can only apply 3.3V */
+	state->vs_Xv  = 0;
+}
+
+static int viper_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
+					 const socket_state_t *state)
+{
+	/* Silently ignore Vpp, output enable, speaker enable. */
+	viper_cf_rst(state->flags & SS_RESET);
+
+	/* Apply socket voltage */
+	switch (state->Vcc) {
+	case 0:
+		gpio_set_value(VIPER_CF_POWER_GPIO, 0);
+		break;
+	case 33:
+		gpio_set_value(VIPER_CF_POWER_GPIO, 1);
+		break;
+	default:
+		printk(KERN_ERR "%s: Unsupported Vcc:%d\n",
+		       __func__, state->Vcc);
+		return -1;
+	}
+
+	return 0;
+}
+
+static void viper_pcmcia_socket_init(struct soc_pcmcia_socket *skt)
+{
+}
+
+static void viper_pcmcia_socket_suspend(struct soc_pcmcia_socket *skt)
+{
+}
+
+static struct pcmcia_low_level viper_pcmcia_ops __initdata = {
+	.owner          	= THIS_MODULE,
+	.hw_init        	= viper_pcmcia_hw_init,
+	.hw_shutdown		= viper_pcmcia_hw_shutdown,
+	.socket_state		= viper_pcmcia_socket_state,
+	.configure_socket	= viper_pcmcia_configure_socket,
+	.socket_init		= viper_pcmcia_socket_init,
+	.socket_suspend		= viper_pcmcia_socket_suspend,
+	.nr         		= 1,
+};
+
+static struct platform_device *viper_pcmcia_device;
+
+static int __init viper_pcmcia_init(void)
+{
+	int ret;
+
+	if (!machine_is_viper())
+		return -ENODEV;
+
+	viper_pcmcia_device = platform_device_alloc("pxa2xx-pcmcia", -1);
+	if (!viper_pcmcia_device)
+		return -ENOMEM;
+
+	ret = platform_device_add_data(viper_pcmcia_device,
+				       &viper_pcmcia_ops,
+				       sizeof(viper_pcmcia_ops));
+
+	if (!ret)
+		ret = platform_device_add(viper_pcmcia_device);
+
+	if (ret)
+		platform_device_put(viper_pcmcia_device);
+
+	return ret;
+}
+
+static void __exit viper_pcmcia_exit(void)
+{
+	platform_device_unregister(viper_pcmcia_device);
+}
+
+module_init(viper_pcmcia_init);
+module_exit(viper_pcmcia_exit);
+
+MODULE_LICENSE("GPL");
diff --git a/include/linux/smc91x.h b/include/linux/smc91x.h
index 3827b92..bc21db5 100644
--- a/include/linux/smc91x.h
+++ b/include/linux/smc91x.h
@@ -16,8 +16,19 @@
 
 #define SMC91X_USE_DMA		(1 << 6)
 
+#define RPC_LED_100_10	(0x00)	/* LED = 100Mbps OR's with 10Mbps link detect */
+#define RPC_LED_RES	(0x01)	/* LED = Reserved */
+#define RPC_LED_10	(0x02)	/* LED = 10Mbps link detect */
+#define RPC_LED_FD	(0x03)	/* LED = Full Duplex Mode */
+#define RPC_LED_TX_RX	(0x04)	/* LED = TX or RX packet occurred */
+#define RPC_LED_100	(0x05)	/* LED = 100Mbps link dectect */
+#define RPC_LED_TX	(0x06)	/* LED = TX packet occurred */
+#define RPC_LED_RX	(0x07)	/* LED = RX packet occurred */
+
 struct smc91x_platdata {
 	unsigned long flags;
+	unsigned char leda;
+	unsigned char ledb;
 };
 
 #endif /* __SMC91X_H__ */