ARM: at91/soc: use gpio_is_valid to check the gpio
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c
index fc3eb4d..b7582dd 100644
--- a/arch/arm/mach-at91/at91sam9g45_devices.c
+++ b/arch/arm/mach-at91/at91sam9g45_devices.c
@@ -120,7 +120,7 @@
/* Enable VBus control for UHP ports */
for (i = 0; i < data->ports; i++) {
- if (data->vbus_pin[i])
+ if (gpio_is_valid(data->vbus_pin[i]))
at91_set_gpio_output(data->vbus_pin[i], 0);
}
@@ -181,7 +181,7 @@
/* Enable VBus control for UHP ports */
for (i = 0; i < data->ports; i++) {
- if (data->vbus_pin[i])
+ if (gpio_is_valid(data->vbus_pin[i]))
at91_set_gpio_output(data->vbus_pin[i], 0);
}
@@ -263,7 +263,7 @@
usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep);
memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));
- if (data && data->vbus_pin > 0) {
+ if (data && gpio_is_valid(data->vbus_pin)) {
at91_set_gpio_input(data->vbus_pin, 0);
at91_set_deglitch(data->vbus_pin, 1);
usba_udc_data.pdata.vbus_pin = data->vbus_pin;
@@ -316,7 +316,7 @@
if (!data)
return;
- if (data->phy_irq_pin) {
+ if (gpio_is_valid(data->phy_irq_pin)) {
at91_set_gpio_input(data->phy_irq_pin, 0);
at91_set_deglitch(data->phy_irq_pin, 1);
}
@@ -449,11 +449,11 @@
/* input/irq */
- if (data->slot[0].detect_pin) {
+ if (gpio_is_valid(data->slot[0].detect_pin)) {
at91_set_gpio_input(data->slot[0].detect_pin, 1);
at91_set_deglitch(data->slot[0].detect_pin, 1);
}
- if (data->slot[0].wp_pin)
+ if (gpio_is_valid(data->slot[0].wp_pin))
at91_set_gpio_input(data->slot[0].wp_pin, 1);
if (mmc_id == 0) { /* MCI0 */
@@ -556,15 +556,15 @@
at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA);
/* enable pin */
- if (data->enable_pin)
+ if (gpio_is_valid(data->enable_pin))
at91_set_gpio_output(data->enable_pin, 1);
/* ready/busy pin */
- if (data->rdy_pin)
+ if (gpio_is_valid(data->rdy_pin))
at91_set_gpio_input(data->rdy_pin, 1);
/* card detect pin */
- if (data->det_pin)
+ if (gpio_is_valid(data->det_pin))
at91_set_gpio_input(data->det_pin, 1);
nand_data = *data;
@@ -859,7 +859,7 @@
at91_set_A_periph(AT91_PIN_PD6, 0); /* AC97RX */
/* reset */
- if (data->reset_pin)
+ if (gpio_is_valid(data->reset_pin))
at91_set_gpio_output(data->reset_pin, 0);
ac97_data = *data;