| /* Copyright (c) 2016-2018, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| #include <dt-bindings/spmi/spmi.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| |
| &spmi_bus { |
| qcom,pm8005@4 { |
| compatible = "qcom,spmi-pmic"; |
| reg = <0x4 SPMI_USID>; |
| #address-cells = <2>; |
| #size-cells = <0>; |
| |
| pm8005_revid: qcom,revid@100 { |
| compatible = "qcom,qpnp-revid"; |
| reg = <0x100 0x100>; |
| }; |
| |
| pm8005_tz: qcom,temp-alarm@2400 { |
| compatible = "qcom,qpnp-temp-alarm"; |
| reg = <0x2400 0x100>; |
| interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_RISING>; |
| label = "pm8005_tz"; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pm8005_gpios: pinctrl@c000 { |
| compatible = "qcom,spmi-gpio"; |
| reg = <0xc000 0x400>; |
| interrupts = <0x4 0xc0 0 IRQ_TYPE_NONE>, |
| <0x4 0xc1 0 IRQ_TYPE_NONE>; |
| interrupt-names = "pm8005_gpio1", "pm8005_gpio2"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| qcom,gpios-disallowed = <3 4>; |
| }; |
| }; |
| |
| qcom,pm8005@5 { |
| compatible ="qcom,spmi-pmic"; |
| reg = <0x5 SPMI_USID>; |
| #address-cells = <2>; |
| #size-cells = <0>; |
| |
| regulator@1400 { |
| compatible = "qcom,qpnp-regulator"; |
| reg = <0x1400 0x100>; |
| regulator-name = "pm8005_s1"; |
| status = "disabled"; |
| }; |
| |
| regulator@1700 { |
| compatible = "qcom,qpnp-regulator"; |
| reg = <0x1700 0x100>; |
| regulator-name = "pm8005_s2"; |
| status = "disabled"; |
| }; |
| |
| regulator@1a00 { |
| compatible = "qcom,qpnp-regulator"; |
| reg = <0x1a00 0x100>; |
| regulator-name = "pm8005_s3"; |
| status = "disabled"; |
| }; |
| |
| regulator@1d00 { |
| compatible = "qcom,qpnp-regulator"; |
| reg = <0x1d00 0x100>; |
| regulator-name = "pm8005_s4"; |
| status = "disabled"; |
| }; |
| }; |
| }; |
| |
| &thermal_zones { |
| pm8005_tz { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&pm8005_tz>; |
| trips { |
| pm8005-trip0 { |
| temperature = <105000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| pm8005-trip1 { |
| temperature = <125000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| pm8005-trip2 { |
| temperature = <145000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| }; |