blob: 89f0cc74a5197a28d521c7714750dcaf21a6f963 [file] [log] [blame]
/*
* linux/arch/arm/mach-omap1/board-h2.c
*
* Board specific inits for OMAP-1610 H2
*
* Copyright (C) 2001 RidgeRun, Inc.
* Author: Greg Lonnon <glonnon@ridgerun.com>
*
* Copyright (C) 2002 MontaVista Software, Inc.
*
* Separated FPGA interrupts from innovator1510.c and cleaned up for 2.6
* Copyright (C) 2004 Nokia Corporation by Tony Lindrgen <tony@atomide.com>
*
* H2 specific changes and cleanup
* Copyright (C) 2004 Nokia Corporation by Imre Deak <imre.deak@nokia.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <asm/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
#include <asm/arch/gpio.h>
#include <asm/arch/mux.h>
#include <asm/arch/tc.h>
#include <asm/arch/usb.h>
#include <asm/arch/common.h>
extern int omap_gpio_init(void);
static struct mtd_partition h2_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
{
.name = "bootloader",
.offset = 0,
.size = SZ_128K,
.mask_flags = MTD_WRITEABLE, /* force read-only */
},
/* bootloader params in the next sector */
{
.name = "params",
.offset = MTDPART_OFS_APPEND,
.size = SZ_128K,
.mask_flags = 0,
},
/* kernel */
{
.name = "kernel",
.offset = MTDPART_OFS_APPEND,
.size = SZ_2M,
.mask_flags = 0
},
/* file system */
{
.name = "filesystem",
.offset = MTDPART_OFS_APPEND,
.size = MTDPART_SIZ_FULL,
.mask_flags = 0
}
};
static struct flash_platform_data h2_flash_data = {
.map_name = "cfi_probe",
.width = 2,
.parts = h2_partitions,
.nr_parts = ARRAY_SIZE(h2_partitions),
};
static struct resource h2_flash_resource = {
/* This is on CS3, wherever it's mapped */
.flags = IORESOURCE_MEM,
};
static struct platform_device h2_flash_device = {
.name = "omapflash",
.id = 0,
.dev = {
.platform_data = &h2_flash_data,
},
.num_resources = 1,
.resource = &h2_flash_resource,
};
static struct resource h2_smc91x_resources[] = {
[0] = {
.start = OMAP1610_ETHR_START, /* Physical */
.end = OMAP1610_ETHR_START + 0xf,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = OMAP_GPIO_IRQ(0),
.end = OMAP_GPIO_IRQ(0),
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device h2_smc91x_device = {
.name = "smc91x",
.id = 0,
.num_resources = ARRAY_SIZE(h2_smc91x_resources),
.resource = h2_smc91x_resources,
};
static struct platform_device *h2_devices[] __initdata = {
&h2_flash_device,
&h2_smc91x_device,
};
static void __init h2_init_smc91x(void)
{
if ((omap_request_gpio(0)) < 0) {
printk("Error requesting gpio 0 for smc91x irq\n");
return;
}
}
static void __init h2_init_irq(void)
{
omap1_init_common_hw();
omap_init_irq();
omap_gpio_init();
h2_init_smc91x();
}
static struct omap_usb_config h2_usb_config __initdata = {
/* usb1 has a Mini-AB port and external isp1301 transceiver */
.otg = 2,
#ifdef CONFIG_USB_GADGET_OMAP
.hmc_mode = 19, // 0:host(off) 1:dev|otg 2:disabled
// .hmc_mode = 21, // 0:host(off) 1:dev(loopback) 2:host(loopback)
#elif defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
/* needs OTG cable, or NONSTANDARD (B-to-MiniB) */
.hmc_mode = 20, // 1:dev|otg(off) 1:host 2:disabled
#endif
.pins[1] = 3,
};
static struct omap_mmc_config h2_mmc_config __initdata = {
.mmc [0] = {
.enabled = 1,
.wire4 = 1,
.wp_pin = OMAP_MPUIO(3),
.power_pin = -1, /* tps65010 gpio3 */
.switch_pin = OMAP_MPUIO(1),
},
};
static struct omap_uart_config h2_uart_config __initdata = {
.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
};
static struct omap_lcd_config h2_lcd_config __initdata = {
.panel_name = "h2",
.ctrl_name = "internal",
};
static struct omap_board_config_kernel h2_config[] = {
{ OMAP_TAG_USB, &h2_usb_config },
{ OMAP_TAG_MMC, &h2_mmc_config },
{ OMAP_TAG_UART, &h2_uart_config },
{ OMAP_TAG_LCD, &h2_lcd_config },
};
static void __init h2_init(void)
{
/* NOTE: revC boards support NAND-boot, which can put NOR on CS2B
* and NAND (either 16bit or 8bit) on CS3.
*/
h2_flash_resource.end = h2_flash_resource.start = omap_cs3_phys();
h2_flash_resource.end += SZ_32M - 1;
/* MMC: card detect and WP */
// omap_cfg_reg(U19_ARMIO1); /* CD */
omap_cfg_reg(BALLOUT_V8_ARMIO3); /* WP */
platform_add_devices(h2_devices, ARRAY_SIZE(h2_devices));
omap_board_config = h2_config;
omap_board_config_size = ARRAY_SIZE(h2_config);
omap_serial_init();
}
static void __init h2_map_io(void)
{
omap1_map_common_io();
}
MACHINE_START(OMAP_H2, "TI-H2")
/* Maintainer: Imre Deak <imre.deak@nokia.com> */
.phys_io = 0xfff00000,
.io_pg_offst = ((0xfef00000) >> 18) & 0xfffc,
.boot_params = 0x10000100,
.map_io = h2_map_io,
.init_irq = h2_init_irq,
.init_machine = h2_init,
.timer = &omap_timer,
MACHINE_END