Merge branch 'for-arm-soc-next' of git://git.linaro.org/people/ljones/linux-3.0-ux500 into next/dt
From Lee Jones <lee.jones@linaro.org>:
* 'for-arm-soc-next' of git://git.linaro.org/people/ljones/linux-3.0-ux500:
ARM: ux500: Remove PMU platform registration when booting with DT
ARM: ux500: Remove temporary snowball_of_platform_devs enablement structure
ARM: ux500: Ensure vendor specific properties have the vendor's identifier
pinctrl: pinctrl-nomadik: Append sleepmode property with vendor specific prefixes
ARM: ux500: Move rtc-pl031 registration to Device Tree when enabled
ARM: ux500: Enable the AB8500 RTC for all DT:ed DB8500 based devices
ARM: ux500: Correctly reference IRQs supplied by the AB8500 from Device Tree
ARM: ux500: Apply ab8500-debug node do the db8500 DT structure
ARM: ux500: Add a ab8500-usb Device Tree node for db8500 based devices
ARM: ux500: Add db8500 Device Tree node for misc/ab8500-pwm
ARM: ux500: Add db8500 Device Tree node for ab8500-sysctrl
ARM: ux500: Enable LED heartbeat functionality on Snowbal via DT
ARM: ux500: Enable LED heartbeat functionality on Snowball
ARM: ux500: Add support for input/ponkey into the db8500's Device Tree
ARM: ux500: Add a ab8500-gpadc node to the db8500 Device Tree
ARM: ux500: Enable the user LED on Snowball via Device Tree
ARM: ux500: Kconfig: Compile in leds-gpio support for Snowball
ARM: ux500: Provide auxdata to be used as name base clock search for nmk-i2c
ARM: ux500: Remove unused i2c platform_data initialisation code
ARM: ux500: Enable Device Tree support mmci for Snowball
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
diff --git a/Documentation/devicetree/bindings/gpio/gpio-nmk.txt b/Documentation/devicetree/bindings/gpio/gpio-nmk.txt
index ee87467..8315ac7 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-nmk.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-nmk.txt
@@ -26,6 +26,6 @@
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
- supports-sleepmode;
+ st,supports-sleepmode;
gpio-bank = <1>;
};
diff --git a/arch/arm/boot/dts/db8500.dtsi b/arch/arm/boot/dts/db8500.dtsi
index 4ad5160..e9c2e92 100644
--- a/arch/arm/boot/dts/db8500.dtsi
+++ b/arch/arm/boot/dts/db8500.dtsi
@@ -48,7 +48,7 @@
};
rtc@80154000 {
- compatible = "stericsson,db8500-rtc";
+ compatible = "arm,rtc-pl031", "arm,primecell";
reg = <0x80154000 0x1000>;
interrupts = <0 18 0x4>;
};
@@ -60,7 +60,7 @@
interrupts = <0 119 0x4>;
interrupt-controller;
#interrupt-cells = <2>;
- supports-sleepmode;
+ st,supports-sleepmode;
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <0>;
@@ -73,7 +73,7 @@
interrupts = <0 120 0x4>;
interrupt-controller;
#interrupt-cells = <2>;
- supports-sleepmode;
+ st,supports-sleepmode;
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <1>;
@@ -86,7 +86,7 @@
interrupts = <0 121 0x4>;
interrupt-controller;
#interrupt-cells = <2>;
- supports-sleepmode;
+ st,supports-sleepmode;
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <2>;
@@ -99,7 +99,7 @@
interrupts = <0 122 0x4>;
interrupt-controller;
#interrupt-cells = <2>;
- supports-sleepmode;
+ st,supports-sleepmode;
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <3>;
@@ -112,7 +112,7 @@
interrupts = <0 123 0x4>;
interrupt-controller;
#interrupt-cells = <2>;
- supports-sleepmode;
+ st,supports-sleepmode;
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <4>;
@@ -125,7 +125,7 @@
interrupts = <0 124 0x4>;
interrupt-controller;
#interrupt-cells = <2>;
- supports-sleepmode;
+ st,supports-sleepmode;
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <5>;
@@ -138,7 +138,7 @@
interrupts = <0 125 0x4>;
interrupt-controller;
#interrupt-cells = <2>;
- supports-sleepmode;
+ st,supports-sleepmode;
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <6>;
@@ -151,7 +151,7 @@
interrupts = <0 126 0x4>;
interrupt-controller;
#interrupt-cells = <2>;
- supports-sleepmode;
+ st,supports-sleepmode;
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <7>;
@@ -164,7 +164,7 @@
interrupts = <0 127 0x4>;
interrupt-controller;
#interrupt-cells = <2>;
- supports-sleepmode;
+ st,supports-sleepmode;
gpio-controller;
#gpio-cells = <2>;
gpio-bank = <8>;
@@ -312,6 +312,63 @@
compatible = "stericsson,ab8500";
reg = <5>; /* mailbox 5 is i2c */
interrupts = <0 40 0x4>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ ab8500-rtc {
+ compatible = "stericsson,ab8500-rtc";
+ interrupts = <17 0x4
+ 18 0x4>;
+ interrupt-names = "60S", "ALARM";
+ };
+
+ ab8500-gpadc {
+ compatible = "stericsson,ab8500-gpadc";
+ interrupts = <32 0x4
+ 39 0x4>;
+ interrupt-names = "HW_CONV_END", "SW_CONV_END";
+ vddadc-supply = <&ab8500_ldo_tvout_reg>;
+ };
+
+ ab8500-usb {
+ compatible = "stericsson,ab8500-usb";
+ interrupts = < 90 0x4
+ 96 0x4
+ 14 0x4
+ 15 0x4
+ 79 0x4
+ 74 0x4
+ 75 0x4>;
+ interrupt-names = "ID_WAKEUP_R",
+ "ID_WAKEUP_F",
+ "VBUS_DET_F",
+ "VBUS_DET_R",
+ "USB_LINK_STATUS",
+ "USB_ADP_PROBE_PLUG",
+ "USB_ADP_PROBE_UNPLUG";
+ vddulpivio18-supply = <&ab8500_ldo_initcore_reg>;
+ v-ape-supply = <&db8500_vape_reg>;
+ musb_1v8-supply = <&db8500_vsmps2_reg>;
+ };
+
+ ab8500-ponkey {
+ compatible = "stericsson,ab8500-ponkey";
+ interrupts = <6 0x4
+ 7 0x4>;
+ interrupt-names = "ONKEY_DBF", "ONKEY_DBR";
+ };
+
+ ab8500-sysctrl {
+ compatible = "stericsson,ab8500-sysctrl";
+ };
+
+ ab8500-pwm {
+ compatible = "stericsson,ab8500-pwm";
+ };
+
+ ab8500-debugfs {
+ compatible = "stericsson,ab8500-debug";
+ };
ab8500-regulators {
compatible = "stericsson,ab8500-regulator";
diff --git a/arch/arm/boot/dts/snowball.dts b/arch/arm/boot/dts/snowball.dts
index ec3c339..7e334d4 100644
--- a/arch/arm/boot/dts/snowball.dts
+++ b/arch/arm/boot/dts/snowball.dts
@@ -77,6 +77,8 @@
used-led {
label = "user_led";
gpios = <&gpio4 14 0x4>;
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
};
};
@@ -101,15 +103,30 @@
};
};
+ // External Micro SD slot
sdi@80126000 {
- status = "enabled";
+ arm,primecell-periphid = <0x10480180>;
+ max-frequency = <50000000>;
+ bus-width = <8>;
+ mmc-cap-mmc-highspeed;
vmmc-supply = <&ab8500_ldo_aux3_reg>;
+
+ #gpio-cells = <1>;
cd-gpios = <&gpio6 26 0x4>; // 218
+ cd-inverted;
+
+ status = "okay";
};
+ // On-board eMMC
sdi@80114000 {
- status = "enabled";
+ arm,primecell-periphid = <0x10480180>;
+ max-frequency = <50000000>;
+ bus-width = <8>;
+ mmc-cap-mmc-highspeed;
vmmc-supply = <&ab8500_ldo_aux2_reg>;
+
+ status = "okay";
};
uart@80120000 {
diff --git a/arch/arm/mach-ux500/Kconfig b/arch/arm/mach-ux500/Kconfig
index 53d3d46..c013bbf 100644
--- a/arch/arm/mach-ux500/Kconfig
+++ b/arch/arm/mach-ux500/Kconfig
@@ -41,6 +41,7 @@
config MACH_SNOWBALL
bool "U8500 Snowball platform"
select MACH_MOP500
+ select LEDS_GPIO
help
Include support for the snowball development platform.
diff --git a/arch/arm/mach-ux500/board-mop500-sdi.c b/arch/arm/mach-ux500/board-mop500-sdi.c
index 920251c..18ff781 100644
--- a/arch/arm/mach-ux500/board-mop500-sdi.c
+++ b/arch/arm/mach-ux500/board-mop500-sdi.c
@@ -80,7 +80,7 @@
};
#endif
-static struct mmci_platform_data mop500_sdi0_data = {
+struct mmci_platform_data mop500_sdi0_data = {
.ios_handler = mop500_sdi0_ios_handler,
.ocr_mask = MMC_VDD_29_30,
.f_max = 50000000,
@@ -227,7 +227,7 @@
};
#endif
-static struct mmci_platform_data mop500_sdi4_data = {
+struct mmci_platform_data mop500_sdi4_data = {
.ocr_mask = MMC_VDD_29_30,
.f_max = 50000000,
.capabilities = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA |
diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c
index 4fd93f5..84461fa 100644
--- a/arch/arm/mach-ux500/board-mop500.c
+++ b/arch/arm/mach-ux500/board-mop500.c
@@ -58,7 +58,7 @@
static struct gpio_led snowball_led_array[] = {
{
.name = "user_led",
- .default_trigger = "none",
+ .default_trigger = "heartbeat",
.gpio = 142,
},
};
@@ -331,43 +331,12 @@
},
};
-#define U8500_I2C_CONTROLLER(id, _slsu, _tft, _rft, clk, t_out, _sm) \
-static struct nmk_i2c_controller u8500_i2c##id##_data = { \
- /* \
- * slave data setup time, which is \
- * 250 ns,100ns,10ns which is 14,6,2 \
- * respectively for a 48 Mhz \
- * i2c clock \
- */ \
- .slsu = _slsu, \
- /* Tx FIFO threshold */ \
- .tft = _tft, \
- /* Rx FIFO threshold */ \
- .rft = _rft, \
- /* std. mode operation */ \
- .clk_freq = clk, \
- /* Slave response timeout(ms) */\
- .timeout = t_out, \
- .sm = _sm, \
-}
-
-/*
- * The board uses 4 i2c controllers, initialize all of
- * them with slave data setup time of 250 ns,
- * Tx & Rx FIFO threshold values as 8 and standard
- * mode of operation
- */
-U8500_I2C_CONTROLLER(0, 0xe, 1, 8, 100000, 200, I2C_FREQ_MODE_FAST);
-U8500_I2C_CONTROLLER(1, 0xe, 1, 8, 100000, 200, I2C_FREQ_MODE_FAST);
-U8500_I2C_CONTROLLER(2, 0xe, 1, 8, 100000, 200, I2C_FREQ_MODE_FAST);
-U8500_I2C_CONTROLLER(3, 0xe, 1, 8, 100000, 200, I2C_FREQ_MODE_FAST);
-
static void __init mop500_i2c_init(struct device *parent)
{
- db8500_add_i2c0(parent, &u8500_i2c0_data);
- db8500_add_i2c1(parent, &u8500_i2c1_data);
- db8500_add_i2c2(parent, &u8500_i2c2_data);
- db8500_add_i2c3(parent, &u8500_i2c3_data);
+ db8500_add_i2c0(parent, NULL);
+ db8500_add_i2c1(parent, NULL);
+ db8500_add_i2c2(parent, NULL);
+ db8500_add_i2c3(parent, NULL);
}
static struct gpio_keys_button mop500_gpio_keys[] = {
@@ -776,6 +745,8 @@
OF_DEV_AUXDATA("arm,pl011", 0x80007000, "uart2", &uart2_plat),
/* Requires DMA bindings. */
OF_DEV_AUXDATA("arm,pl022", 0x80002000, "ssp0", &ssp0_plat),
+ OF_DEV_AUXDATA("arm,pl18x", 0x80126000, "sdi0", &mop500_sdi0_data),
+ OF_DEV_AUXDATA("arm,pl18x", 0x80114000, "sdi4", &mop500_sdi4_data),
/* Requires clock name bindings. */
OF_DEV_AUXDATA("st,nomadik-gpio", 0x8012e000, "gpio.0", NULL),
OF_DEV_AUXDATA("st,nomadik-gpio", 0x8012e080, "gpio.1", NULL),
@@ -786,6 +757,11 @@
OF_DEV_AUXDATA("st,nomadik-gpio", 0x8011e000, "gpio.6", NULL),
OF_DEV_AUXDATA("st,nomadik-gpio", 0x8011e080, "gpio.7", NULL),
OF_DEV_AUXDATA("st,nomadik-gpio", 0xa03fe000, "gpio.8", NULL),
+ OF_DEV_AUXDATA("st,nomadik-i2c", 0x80004000, "nmk-i2c.0", NULL),
+ OF_DEV_AUXDATA("st,nomadik-i2c", 0x80122000, "nmk-i2c.1", NULL),
+ OF_DEV_AUXDATA("st,nomadik-i2c", 0x80128000, "nmk-i2c.2", NULL),
+ OF_DEV_AUXDATA("st,nomadik-i2c", 0x80110000, "nmk-i2c.3", NULL),
+ OF_DEV_AUXDATA("st,nomadik-i2c", 0x8012a000, "nmk-i2c.4", NULL),
/* Requires device name bindings. */
OF_DEV_AUXDATA("stericsson,nmk_pinctrl", 0, "pinctrl-db8500", NULL),
{},
@@ -820,8 +796,6 @@
for (i = 0; i < ARRAY_SIZE(mop500_platform_devs); i++)
mop500_platform_devs[i]->dev.parent = parent;
- for (i = 0; i < ARRAY_SIZE(snowball_platform_devs); i++)
- snowball_platform_devs[i]->dev.parent = parent;
/* automatically probe child nodes of db8500 device */
of_platform_populate(NULL, u8500_local_bus_nodes, u8500_auxdata_lookup, parent);
@@ -840,18 +814,6 @@
mop500_uib_init();
- } else if (of_machine_is_compatible("calaosystems,snowball-a9500")) {
- /*
- * Devices to be DT:ed:
- * snowball_led_dev = todo
- * snowball_key_dev = todo
- * snowball_sbnet_dev = done
- * ab8500_device = done
- */
- platform_add_devices(snowball_of_platform_devs,
- ARRAY_SIZE(snowball_of_platform_devs));
-
- snowball_sdi_init(parent);
} else if (of_machine_is_compatible("st-ericsson,hrefv60+")) {
/*
* The HREFv60 board removed a GPIO expander and routed
@@ -873,7 +835,6 @@
mop500_uib_init();
}
- mop500_i2c_init(parent);
/* This board has full regulator constraints */
regulator_has_full_constraints();
diff --git a/arch/arm/mach-ux500/board-mop500.h b/arch/arm/mach-ux500/board-mop500.h
index 2f87b25..b5bfc1a 100644
--- a/arch/arm/mach-ux500/board-mop500.h
+++ b/arch/arm/mach-ux500/board-mop500.h
@@ -9,6 +9,7 @@
/* For NOMADIK_NR_GPIO */
#include <mach/irqs.h>
+#include <linux/amba/mmci.h>
/* Snowball specific GPIO assignments, this board has no GPIO expander */
#define SNOWBALL_ACCEL_INT1_GPIO 163
@@ -78,6 +79,8 @@
struct device;
struct i2c_board_info;
+extern struct mmci_platform_data mop500_sdi0_data;
+extern struct mmci_platform_data mop500_sdi4_data;
extern void mop500_sdi_init(struct device *parent);
extern void snowball_sdi_init(struct device *parent);
diff --git a/arch/arm/mach-ux500/cpu-db8500.c b/arch/arm/mach-ux500/cpu-db8500.c
index 33275eb..c8dd94f 100644
--- a/arch/arm/mach-ux500/cpu-db8500.c
+++ b/arch/arm/mach-ux500/cpu-db8500.c
@@ -139,7 +139,6 @@
static struct platform_device *of_platform_devs[] __initdata = {
&u8500_dma40_device,
- &db8500_pmu_device,
};
static resource_size_t __initdata db8500_gpio_base[] = {
@@ -237,7 +236,6 @@
parent = db8500_soc_device_init();
- db8500_add_rtc(parent);
db8500_add_usb(parent, usb_db8500_rx_dma_cfg, usb_db8500_tx_dma_cfg);
platform_device_register_data(parent,
@@ -249,7 +247,7 @@
/*
* Devices to be DT:ed:
* u8500_dma40_device = todo
- * db8500_pmu_device = todo
+ * db8500_pmu_device = done
* db8500_prcmu_device = done
*/
platform_add_devices(of_platform_devs, ARRAY_SIZE(of_platform_devs));
diff --git a/drivers/i2c/busses/i2c-nomadik.c b/drivers/i2c/busses/i2c-nomadik.c
index 5267ab9..a92440d 100644
--- a/drivers/i2c/busses/i2c-nomadik.c
+++ b/drivers/i2c/busses/i2c-nomadik.c
@@ -965,8 +965,7 @@
adap->owner = THIS_MODULE;
adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD;
adap->algo = &nmk_i2c_algo;
- adap->timeout = pdata->timeout ? msecs_to_jiffies(pdata->timeout) :
- msecs_to_jiffies(20000);
+ adap->timeout = msecs_to_jiffies(pdata->timeout);
snprintf(adap->name, sizeof(adap->name),
"Nomadik I2C%d at %lx", pdev->id, (unsigned long)res->start);
diff --git a/drivers/pinctrl/pinctrl-nomadik.c b/drivers/pinctrl/pinctrl-nomadik.c
index 3e7e47d..dd9e6f2 100644
--- a/drivers/pinctrl/pinctrl-nomadik.c
+++ b/drivers/pinctrl/pinctrl-nomadik.c
@@ -1198,7 +1198,7 @@
if (!pdata)
return -ENOMEM;
- if (of_get_property(np, "supports-sleepmode", NULL))
+ if (of_get_property(np, "st,supports-sleepmode", NULL))
pdata->supports_sleepmode = true;
if (of_property_read_u32(np, "gpio-bank", &dev->id)) {