[SCSI] aic7[9x]xx: Remove last vestiges of reverse_scan
Remove last vestiges of the reverse_scan paramater from aic7xxx and aic79xx.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
diff --git a/drivers/scsi/aic7xxx/aic79xx_osm.c b/drivers/scsi/aic7xxx/aic79xx_osm.c
index b244c71..998999c 100644
--- a/drivers/scsi/aic7xxx/aic79xx_osm.c
+++ b/drivers/scsi/aic7xxx/aic79xx_osm.c
@@ -243,25 +243,6 @@
static uint32_t aic79xx_no_reset;
/*
- * Certain PCI motherboards will scan PCI devices from highest to lowest,
- * others scan from lowest to highest, and they tend to do all kinds of
- * strange things when they come into contact with PCI bridge chips. The
- * net result of all this is that the PCI card that is actually used to boot
- * the machine is very hard to detect. Most motherboards go from lowest
- * PCI slot number to highest, and the first SCSI controller found is the
- * one you boot from. The only exceptions to this are when a controller
- * has its BIOS disabled. So, we by default sort all of our SCSI controllers
- * from lowest PCI slot number to highest PCI slot number. We also force
- * all controllers with their BIOS disabled to the end of the list. This
- * works on *almost* all computers. Where it doesn't work, we have this
- * option. Setting this option to non-0 will reverse the order of the sort
- * to highest first, then lowest, but will still leave cards with their BIOS
- * disabled at the very end. That should fix everyone up unless there are
- * really strange cirumstances.
- */
-static uint32_t aic79xx_reverse_scan;
-
-/*
* Should we force EXTENDED translation on a controller.
* 0 == Use whatever is in the SEEPROM or default to off
* 1 == Use whatever is in the SEEPROM or default to on
@@ -350,7 +331,6 @@
" periodically to prevent tag starvation.\n"
" This may be required by some older disk\n"
" or drives/RAID arrays.\n"
-" reverse_scan Sort PCI devices highest Bus/Slot to lowest\n"
" tag_info:<tag_str> Set per-target tag depth\n"
" global_tag_depth:<int> Global tag depth for all targets on all buses\n"
" slewrate:<slewrate_list>Set the signal slew rate (0-15).\n"
@@ -1031,7 +1011,6 @@
#ifdef AHD_DEBUG
{ "debug", &ahd_debug },
#endif
- { "reverse_scan", &aic79xx_reverse_scan },
{ "periodic_otag", &aic79xx_periodic_otag },
{ "pci_parity", &aic79xx_pci_parity },
{ "seltime", &aic79xx_seltime },
diff --git a/drivers/scsi/aic7xxx/aic7xxx_osm.c b/drivers/scsi/aic7xxx/aic7xxx_osm.c
index debf3e2..aa4be8a 100644
--- a/drivers/scsi/aic7xxx/aic7xxx_osm.c
+++ b/drivers/scsi/aic7xxx/aic7xxx_osm.c
@@ -353,7 +353,6 @@
" periodically to prevent tag starvation.\n"
" This may be required by some older disk\n"
" drives or RAID arrays.\n"
-" reverse_scan Sort PCI devices highest Bus/Slot to lowest\n"
" tag_info:<tag_str> Set per-target tag depth\n"
" global_tag_depth:<int> Global tag depth for every target\n"
" on every bus\n"