Input: tsc2005 - convert to gpiod
The GPIOD API can be used from boardcode, so that the DT check can be
removed. To avoid breaking existing boardcode, _optional() variant has been
chosen. For completely removing the DT check, the regulator has also been
made optional, so that it could be supplied from boardcode.
As a side-effect the patch fixes the after-probe reset GPIO state, so that
the device is not kept in reset state.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
diff --git a/drivers/input/touchscreen/tsc2005.c b/drivers/input/touchscreen/tsc2005.c
index 4d3f3ee..0f65d02 100644
--- a/drivers/input/touchscreen/tsc2005.c
+++ b/drivers/input/touchscreen/tsc2005.c
@@ -30,11 +30,11 @@
#include <linux/delay.h>
#include <linux/pm.h>
#include <linux/of.h>
-#include <linux/of_gpio.h>
#include <linux/spi/spi.h>
#include <linux/spi/tsc2005.h>
#include <linux/regulator/consumer.h>
#include <linux/regmap.h>
+#include <linux/gpio/consumer.h>
/*
* The touchscreen interface operates as follows:
@@ -180,7 +180,7 @@
struct regulator *vio;
- int reset_gpio;
+ struct gpio_desc *reset_gpio;
void (*set_reset)(bool enable);
};
@@ -318,8 +318,8 @@
static void tsc2005_set_reset(struct tsc2005 *ts, bool enable)
{
- if (ts->reset_gpio >= 0)
- gpio_set_value(ts->reset_gpio, enable);
+ if (ts->reset_gpio)
+ gpiod_set_value_cansleep(ts->reset_gpio, enable);
else if (ts->set_reset)
ts->set_reset(enable);
}
@@ -611,35 +611,24 @@
ts->x_plate_ohm = x_plate_ohm;
ts->esd_timeout = esd_timeout;
- if (np) {
- ts->reset_gpio = of_get_named_gpio(np, "reset-gpios", 0);
- if (ts->reset_gpio == -EPROBE_DEFER)
- return ts->reset_gpio;
- if (ts->reset_gpio < 0) {
- dev_err(&spi->dev, "error acquiring reset gpio: %d\n",
- ts->reset_gpio);
- return ts->reset_gpio;
- }
-
- error = devm_gpio_request_one(&spi->dev, ts->reset_gpio, 0,
- "reset-gpios");
- if (error) {
- dev_err(&spi->dev, "error requesting reset gpio: %d\n",
- error);
- return error;
- }
-
- ts->vio = devm_regulator_get(&spi->dev, "vio");
- if (IS_ERR(ts->vio)) {
- error = PTR_ERR(ts->vio);
- dev_err(&spi->dev, "vio regulator missing (%d)", error);
- return error;
- }
- } else {
- ts->reset_gpio = -1;
- ts->set_reset = pdata->set_reset;
+ ts->reset_gpio = devm_gpiod_get_optional(&spi->dev, "reset",
+ GPIOD_OUT_HIGH);
+ if (IS_ERR(ts->reset_gpio)) {
+ error = PTR_ERR(ts->reset_gpio);
+ dev_err(&spi->dev, "error acquiring reset gpio: %d\n", error);
+ return error;
}
+ ts->vio = devm_regulator_get_optional(&spi->dev, "vio");
+ if (IS_ERR(ts->vio)) {
+ error = PTR_ERR(ts->vio);
+ dev_err(&spi->dev, "vio regulator missing (%d)", error);
+ return error;
+ }
+
+ if (!ts->reset_gpio && pdata)
+ ts->set_reset = pdata->set_reset;
+
mutex_init(&ts->mutex);
spin_lock_init(&ts->lock);