powerpc/cpm: Remove !CONFIG_PPC_CPM_NEW_BINDING code
Now that arch/ppc is gone we always define CONFIG_PPC_CPM_NEW_BINDING so
we can remove all the code associated with !CONFIG_PPC_CPM_NEW_BINDING.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
diff --git a/include/asm-powerpc/cpm1.h b/include/asm-powerpc/cpm1.h
index 3df4396..2ff79874 100644
--- a/include/asm-powerpc/cpm1.h
+++ b/include/asm-powerpc/cpm1.h
@@ -42,35 +42,15 @@
#define mk_cr_cmd(CH, CMD) ((CMD << 8) | (CH << 4))
-#ifndef CONFIG_PPC_CPM_NEW_BINDING
-/* The dual ported RAM is multi-functional. Some areas can be (and are
- * being) used for microcode. There is an area that can only be used
- * as data ram for buffer descriptors, which is all we use right now.
- * Currently the first 512 and last 256 bytes are used for microcode.
- */
-#define CPM_DATAONLY_BASE ((uint)0x0800)
-#define CPM_DATAONLY_SIZE ((uint)0x0700)
-#define CPM_DP_NOSPACE ((uint)0x7fffffff)
-#endif
-
/* Export the base address of the communication processor registers
* and dual port ram.
*/
extern cpm8xx_t __iomem *cpmp; /* Pointer to comm processor */
-#ifdef CONFIG_PPC_CPM_NEW_BINDING
#define cpm_dpalloc cpm_muram_alloc
#define cpm_dpfree cpm_muram_free
#define cpm_dpram_addr cpm_muram_addr
#define cpm_dpram_phys cpm_muram_dma
-#else
-extern unsigned long cpm_dpalloc(uint size, uint align);
-extern int cpm_dpfree(unsigned long offset);
-extern unsigned long cpm_dpalloc_fixed(unsigned long offset, uint size, uint align);
-extern void cpm_dpdump(void);
-extern void *cpm_dpram_addr(unsigned long offset);
-extern uint cpm_dpram_phys(u8 *addr);
-#endif
extern void cpm_setbrg(uint brg, uint rate);
diff --git a/include/asm-powerpc/cpm2.h b/include/asm-powerpc/cpm2.h
index 4c85ed9..2c7fd9c 100644
--- a/include/asm-powerpc/cpm2.h
+++ b/include/asm-powerpc/cpm2.h
@@ -78,24 +78,6 @@
#define mk_cr_cmd(PG, SBC, MCN, OP) \
((PG << 26) | (SBC << 21) | (MCN << 6) | OP)
-#ifndef CONFIG_PPC_CPM_NEW_BINDING
-/* Dual Port RAM addresses. The first 16K is available for almost
- * any CPM use, so we put the BDs there. The first 128 bytes are
- * used for SMC1 and SMC2 parameter RAM, so we start allocating
- * BDs above that. All of this must change when we start
- * downloading RAM microcode.
- */
-#define CPM_DATAONLY_BASE ((uint)128)
-#define CPM_DP_NOSPACE ((uint)0x7fffffff)
-#if defined(CONFIG_8272) || defined(CONFIG_MPC8555)
-#define CPM_DATAONLY_SIZE ((uint)(8 * 1024) - CPM_DATAONLY_BASE)
-#define CPM_FCC_SPECIAL_BASE ((uint)0x00009000)
-#else
-#define CPM_DATAONLY_SIZE ((uint)(16 * 1024) - CPM_DATAONLY_BASE)
-#define CPM_FCC_SPECIAL_BASE ((uint)0x0000b000)
-#endif
-#endif
-
/* The number of pages of host memory we allocate for CPM. This is
* done early in kernel initialization to get physically contiguous
* pages.
@@ -107,17 +89,9 @@
*/
extern cpm_cpm2_t __iomem *cpmp; /* Pointer to comm processor */
-#ifdef CONFIG_PPC_CPM_NEW_BINDING
#define cpm_dpalloc cpm_muram_alloc
#define cpm_dpfree cpm_muram_free
#define cpm_dpram_addr cpm_muram_addr
-#else
-extern unsigned long cpm_dpalloc(uint size, uint align);
-extern int cpm_dpfree(unsigned long offset);
-extern unsigned long cpm_dpalloc_fixed(unsigned long offset, uint size, uint align);
-extern void cpm_dpdump(void);
-extern void *cpm_dpram_addr(unsigned long offset);
-#endif
extern void cpm_setbrg(uint brg, uint rate);
extern void cpm2_fastbrg(uint brg, uint rate, int div16);