Staging: sm750fb: ddk750_swi2c.c: Place braces on correct lines
Place braces on correct lines in ddk750_swi2c.c
to rectify the following checkpatch errors:
ERROR: that open brace { should be on the previous line
Signed-off-by: Isaac Assegai <isaac.a.travers@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
diff --git a/drivers/staging/sm750fb/ddk750_swi2c.c b/drivers/staging/sm750fb/ddk750_swi2c.c
index a587835..2cf3514 100644
--- a/drivers/staging/sm750fb/ddk750_swi2c.c
+++ b/drivers/staging/sm750fb/ddk750_swi2c.c
@@ -100,8 +100,7 @@
#else
int i, Temp;
- for(i = 0; i < 600; i++)
- {
+ for(i = 0; i < 600; i++) {
Temp = i;
Temp += i;
}
@@ -126,14 +125,11 @@
unsigned long ulGPIODirection;
ulGPIODirection = PEEK32(g_i2cClkGPIODataDirReg);
- if (value) /* High */
- {
+ if (value) { /* High */
/* Set direction as input. This will automatically pull the signal up. */
ulGPIODirection &= ~(1 << g_i2cClockGPIO);
POKE32(g_i2cClkGPIODataDirReg, ulGPIODirection);
- }
- else /* Low */
- {
+ } else { /* Low */
/* Set the signal down */
ulGPIOData = PEEK32(g_i2cClkGPIODataReg);
ulGPIOData &= ~(1 << g_i2cClockGPIO);
@@ -163,14 +159,11 @@
unsigned long ulGPIODirection;
ulGPIODirection = PEEK32(g_i2cDataGPIODataDirReg);
- if (value) /* High */
- {
+ if (value) { /* High */
/* Set direction as input. This will automatically pull the signal up. */
ulGPIODirection &= ~(1 << g_i2cDataGPIO);
POKE32(g_i2cDataGPIODataDirReg, ulGPIODirection);
- }
- else /* Low */
- {
+ } else { /* Low */
/* Set the signal down */
ulGPIOData = PEEK32(g_i2cDataGPIODataReg);
ulGPIOData &= ~(1 << g_i2cDataGPIO);
@@ -195,8 +188,7 @@
/* Make sure that the direction is input (High) */
ulGPIODirection = PEEK32(g_i2cDataGPIODataDirReg);
- if ((ulGPIODirection & (1 << g_i2cDataGPIO)) != (~(1 << g_i2cDataGPIO)))
- {
+ if ((ulGPIODirection & (1 << g_i2cDataGPIO)) != (~(1 << g_i2cDataGPIO))) {
ulGPIODirection &= ~(1 << g_i2cDataGPIO);
POKE32(g_i2cDataGPIODataDirReg, ulGPIODirection);
}
@@ -255,8 +247,7 @@
int i;
/* Sending the data bit by bit */
- for (i = 0; i < 8; i++)
- {
+ for (i = 0; i < 8; i++) {
/* Set SCL to low */
swI2CSCL(0);
@@ -286,8 +277,7 @@
swI2CWait();
/* Read SDA, until SDA==0 */
- for(i = 0; i < 0xff; i++)
- {
+ for(i = 0; i < 0xff; i++) {
if (!swI2CReadSDA())
break;
@@ -322,8 +312,7 @@
int i;
unsigned char data = 0;
- for(i = 7; i >= 0; i--)
- {
+ for(i = 7; i >= 0; i--) {
/* Set the SCL to Low and SDA to High (Input) */
swI2CSCL(0);
swI2CSDA(1);
@@ -510,8 +499,7 @@
*/
if ((swI2CWriteByte(deviceAddress) != 0) ||
(swI2CWriteByte(registerIndex) != 0) ||
- (swI2CWriteByte(data) != 0))
- {
+ (swI2CWriteByte(data) != 0)) {
returnValue = -1;
}