/*
 * INA2XX Current and Power Monitors
 *
 * Copyright 2015 Baylibre SAS.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 *
 * Based on linux/drivers/iio/adc/ad7291.c
 * Copyright 2010-2011 Analog Devices Inc.
 *
 * Based on linux/drivers/hwmon/ina2xx.c
 * Copyright 2012 Lothar Felten <l-felten@ti.com>
 *
 * Licensed under the GPL-2 or later.
 *
 * IIO driver for INA219-220-226-230-231
 *
 * Configurable 7-bit I2C slave address from 0x40 to 0x4F
 */

#include <linux/delay.h>
#include <linux/i2c.h>
#include <linux/iio/kfifo_buf.h>
#include <linux/iio/sysfs.h>
#include <linux/kthread.h>
#include <linux/module.h>
#include <linux/regmap.h>
#include <linux/util_macros.h>

#include <linux/platform_data/ina2xx.h>

/* INA2XX registers definition */
#define INA2XX_CONFIG                   0x00
#define INA2XX_SHUNT_VOLTAGE            0x01	/* readonly */
#define INA2XX_BUS_VOLTAGE              0x02	/* readonly */
#define INA2XX_POWER                    0x03	/* readonly */
#define INA2XX_CURRENT                  0x04	/* readonly */
#define INA2XX_CALIBRATION              0x05

#define INA226_ALERT_MASK		GENMASK(2, 1)
#define INA266_CVRF			BIT(3)

#define INA2XX_MAX_REGISTERS            8

/* settings - depend on use case */
#define INA219_CONFIG_DEFAULT           0x399F	/* PGA=8 */
#define INA226_CONFIG_DEFAULT           0x4327
#define INA226_DEFAULT_AVG              4
#define INA226_DEFAULT_IT		1110

#define INA2XX_RSHUNT_DEFAULT           10000

/*
 * bit mask for reading the averaging setting in the configuration register
 * FIXME: use regmap_fields.
 */
#define INA2XX_MODE_MASK	GENMASK(3, 0)

#define INA226_AVG_MASK		GENMASK(11, 9)
#define INA226_SHIFT_AVG(val)	((val) << 9)

/* Integration time for VBus */
#define INA226_ITB_MASK		GENMASK(8, 6)
#define INA226_SHIFT_ITB(val)	((val) << 6)

/* Integration time for VShunt */
#define INA226_ITS_MASK		GENMASK(5, 3)
#define INA226_SHIFT_ITS(val)	((val) << 3)

/* Cosmetic macro giving the sampling period for a full P=UxI cycle */
#define SAMPLING_PERIOD(c)	((c->int_time_vbus + c->int_time_vshunt) \
				 * c->avg)

static bool ina2xx_is_writeable_reg(struct device *dev, unsigned int reg)
{
	return (reg == INA2XX_CONFIG) || (reg > INA2XX_CURRENT);
}

static bool ina2xx_is_volatile_reg(struct device *dev, unsigned int reg)
{
	return (reg != INA2XX_CONFIG);
}

static inline bool is_signed_reg(unsigned int reg)
{
	return (reg == INA2XX_SHUNT_VOLTAGE) || (reg == INA2XX_CURRENT);
}

static const struct regmap_config ina2xx_regmap_config = {
	.reg_bits = 8,
	.val_bits = 16,
	.max_register = INA2XX_MAX_REGISTERS,
	.writeable_reg = ina2xx_is_writeable_reg,
	.volatile_reg = ina2xx_is_volatile_reg,
};

enum ina2xx_ids { ina219, ina226 };

struct ina2xx_config {
	u16 config_default;
	int calibration_factor;
	int shunt_div;
	int bus_voltage_shift;
	int bus_voltage_lsb;	/* uV */
	int power_lsb;		/* uW */
};

struct ina2xx_chip_info {
	struct regmap *regmap;
	struct task_struct *task;
	const struct ina2xx_config *config;
	struct mutex state_lock;
	unsigned int shunt_resistor;
	int avg;
	s64 prev_ns; /* track buffer capture time, check for underruns */
	int int_time_vbus; /* Bus voltage integration time uS */
	int int_time_vshunt; /* Shunt voltage integration time uS */
	bool allow_async_readout;
};

static const struct ina2xx_config ina2xx_config[] = {
	[ina219] = {
		.config_default = INA219_CONFIG_DEFAULT,
		.calibration_factor = 40960000,
		.shunt_div = 100,
		.bus_voltage_shift = 3,
		.bus_voltage_lsb = 4000,
		.power_lsb = 20000,
	},
	[ina226] = {
		.config_default = INA226_CONFIG_DEFAULT,
		.calibration_factor = 5120000,
		.shunt_div = 400,
		.bus_voltage_shift = 0,
		.bus_voltage_lsb = 1250,
		.power_lsb = 25000,
	},
};

static int ina2xx_read_raw(struct iio_dev *indio_dev,
			   struct iio_chan_spec const *chan,
			   int *val, int *val2, long mask)
{
	int ret;
	struct ina2xx_chip_info *chip = iio_priv(indio_dev);
	unsigned int regval;

	switch (mask) {
	case IIO_CHAN_INFO_RAW:
		ret = regmap_read(chip->regmap, chan->address, &regval);
		if (ret)
			return ret;

		if (is_signed_reg(chan->address))
			*val = (s16) regval;
		else
			*val  = regval;

		return IIO_VAL_INT;

	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
		*val = chip->avg;
		return IIO_VAL_INT;

	case IIO_CHAN_INFO_INT_TIME:
		*val = 0;
		if (chan->address == INA2XX_SHUNT_VOLTAGE)
			*val2 = chip->int_time_vshunt;
		else
			*val2 = chip->int_time_vbus;

		return IIO_VAL_INT_PLUS_MICRO;

	case IIO_CHAN_INFO_SAMP_FREQ:
		/*
		 * Sample freq is read only, it is a consequence of
		 * 1/AVG*(CT_bus+CT_shunt).
		 */
		*val = DIV_ROUND_CLOSEST(1000000, SAMPLING_PERIOD(chip));

		return IIO_VAL_INT;

	case IIO_CHAN_INFO_SCALE:
		switch (chan->address) {
		case INA2XX_SHUNT_VOLTAGE:
			/* processed (mV) = raw*1000/shunt_div */
			*val2 = chip->config->shunt_div;
			*val = 1000;
			return IIO_VAL_FRACTIONAL;

		case INA2XX_BUS_VOLTAGE:
			/* processed (mV) = raw*lsb (uV) / (1000 << shift) */
			*val = chip->config->bus_voltage_lsb;
			*val2 = 1000 << chip->config->bus_voltage_shift;
			return IIO_VAL_FRACTIONAL;

		case INA2XX_POWER:
			/* processed (mW) = raw*lsb (uW) / 1000 */
			*val = chip->config->power_lsb;
			*val2 = 1000;
			return IIO_VAL_FRACTIONAL;

		case INA2XX_CURRENT:
			/* processed (mA) = raw (mA) */
			*val = 1;
			return IIO_VAL_INT;
		}
	}

	return -EINVAL;
}

/*
 * Available averaging rates for ina226. The indices correspond with
 * the bit values expected by the chip (according to the ina226 datasheet,
 * table 3 AVG bit settings, found at
 * http://www.ti.com/lit/ds/symlink/ina226.pdf.
 */
static const int ina226_avg_tab[] = { 1, 4, 16, 64, 128, 256, 512, 1024 };

static int ina226_set_average(struct ina2xx_chip_info *chip, unsigned int val,
			      unsigned int *config)
{
	int bits;

	if (val > 1024 || val < 1)
		return -EINVAL;

	bits = find_closest(val, ina226_avg_tab,
			    ARRAY_SIZE(ina226_avg_tab));

	chip->avg = ina226_avg_tab[bits];

	*config &= ~INA226_AVG_MASK;
	*config |= INA226_SHIFT_AVG(bits) & INA226_AVG_MASK;

	return 0;
}

/* Conversion times in uS */
static const int ina226_conv_time_tab[] = { 140, 204, 332, 588, 1100,
					    2116, 4156, 8244 };

static int ina226_set_int_time_vbus(struct ina2xx_chip_info *chip,
				    unsigned int val_us, unsigned int *config)
{
	int bits;

	if (val_us > 8244 || val_us < 140)
		return -EINVAL;

	bits = find_closest(val_us, ina226_conv_time_tab,
			    ARRAY_SIZE(ina226_conv_time_tab));

	chip->int_time_vbus = ina226_conv_time_tab[bits];

	*config &= ~INA226_ITB_MASK;
	*config |= INA226_SHIFT_ITB(bits) & INA226_ITB_MASK;

	return 0;
}

static int ina226_set_int_time_vshunt(struct ina2xx_chip_info *chip,
				      unsigned int val_us, unsigned int *config)
{
	int bits;

	if (val_us > 8244 || val_us < 140)
		return -EINVAL;

	bits = find_closest(val_us, ina226_conv_time_tab,
			    ARRAY_SIZE(ina226_conv_time_tab));

	chip->int_time_vshunt = ina226_conv_time_tab[bits];

	*config &= ~INA226_ITS_MASK;
	*config |= INA226_SHIFT_ITS(bits) & INA226_ITS_MASK;

	return 0;
}

static int ina2xx_write_raw(struct iio_dev *indio_dev,
			    struct iio_chan_spec const *chan,
			    int val, int val2, long mask)
{
	struct ina2xx_chip_info *chip = iio_priv(indio_dev);
	unsigned int config, tmp;
	int ret;

	if (iio_buffer_enabled(indio_dev))
		return -EBUSY;

	mutex_lock(&chip->state_lock);

	ret = regmap_read(chip->regmap, INA2XX_CONFIG, &config);
	if (ret)
		goto err;

	tmp = config;

	switch (mask) {
	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
		ret = ina226_set_average(chip, val, &tmp);
		break;

	case IIO_CHAN_INFO_INT_TIME:
		if (chan->address == INA2XX_SHUNT_VOLTAGE)
			ret = ina226_set_int_time_vshunt(chip, val2, &tmp);
		else
			ret = ina226_set_int_time_vbus(chip, val2, &tmp);
		break;

	default:
		ret = -EINVAL;
	}

	if (!ret && (tmp != config))
		ret = regmap_write(chip->regmap, INA2XX_CONFIG, tmp);
err:
	mutex_unlock(&chip->state_lock);

	return ret;
}

static ssize_t ina2xx_allow_async_readout_show(struct device *dev,
					   struct device_attribute *attr,
					   char *buf)
{
	struct ina2xx_chip_info *chip = iio_priv(dev_to_iio_dev(dev));

	return sprintf(buf, "%d\n", chip->allow_async_readout);
}

static ssize_t ina2xx_allow_async_readout_store(struct device *dev,
				struct device_attribute *attr,
				const char *buf, size_t len)
{
	struct ina2xx_chip_info *chip = iio_priv(dev_to_iio_dev(dev));
	bool val;
	int ret;

	ret = strtobool((const char *) buf, &val);
	if (ret)
		return ret;

	chip->allow_async_readout = val;

	return len;
}

static int set_shunt_resistor(struct ina2xx_chip_info *chip, unsigned int val)
{
	if (val <= 0 || val > chip->config->calibration_factor)
		return -EINVAL;

	chip->shunt_resistor = val;

	return 0;
}

static ssize_t ina2xx_shunt_resistor_show(struct device *dev,
					  struct device_attribute *attr,
					  char *buf)
{
	struct ina2xx_chip_info *chip = iio_priv(dev_to_iio_dev(dev));

	return sprintf(buf, "%d\n", chip->shunt_resistor);
}

static ssize_t ina2xx_shunt_resistor_store(struct device *dev,
					   struct device_attribute *attr,
					   const char *buf, size_t len)
{
	struct ina2xx_chip_info *chip = iio_priv(dev_to_iio_dev(dev));
	unsigned long val;
	int ret;

	ret = kstrtoul((const char *) buf, 10, &val);
	if (ret)
		return ret;

	ret = set_shunt_resistor(chip, val);
	if (ret)
		return ret;

	return len;
}

#define INA2XX_CHAN(_type, _index, _address) { \
	.type = (_type), \
	.address = (_address), \
	.indexed = 1, \
	.channel = (_index), \
	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) \
	| BIT(IIO_CHAN_INFO_SCALE), \
	.info_mask_shared_by_dir = BIT(IIO_CHAN_INFO_SAMP_FREQ) | \
				   BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO), \
	.scan_index = (_index), \
	.scan_type = { \
		.sign = 'u', \
		.realbits = 16, \
		.storagebits = 16, \
		.endianness = IIO_CPU, \
	} \
}

/*
 * Sampling Freq is a consequence of the integration times of
 * the Voltage channels.
 */
#define INA2XX_CHAN_VOLTAGE(_index, _address) { \
	.type = IIO_VOLTAGE, \
	.address = (_address), \
	.indexed = 1, \
	.channel = (_index), \
	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
			      BIT(IIO_CHAN_INFO_SCALE) | \
			      BIT(IIO_CHAN_INFO_INT_TIME), \
	.scan_index = (_index), \
	.scan_type = { \
		.sign = 'u', \
		.realbits = 16, \
		.storagebits = 16, \
		.endianness = IIO_LE, \
	} \
}

static const struct iio_chan_spec ina2xx_channels[] = {
	INA2XX_CHAN_VOLTAGE(0, INA2XX_SHUNT_VOLTAGE),
	INA2XX_CHAN_VOLTAGE(1, INA2XX_BUS_VOLTAGE),
	INA2XX_CHAN(IIO_POWER, 2, INA2XX_POWER),
	INA2XX_CHAN(IIO_CURRENT, 3, INA2XX_CURRENT),
	IIO_CHAN_SOFT_TIMESTAMP(4),
};

static int ina2xx_work_buffer(struct iio_dev *indio_dev)
{
	struct ina2xx_chip_info *chip = iio_priv(indio_dev);
	unsigned short data[8];
	int bit, ret, i = 0;
	s64 time_a, time_b;
	unsigned int alert;

	time_a = iio_get_time_ns();

	/*
	 * Because the timer thread and the chip conversion clock
	 * are asynchronous, the period difference will eventually
	 * result in reading V[k-1] again, or skip V[k] at time Tk.
	 * In order to resync the timer with the conversion process
	 * we check the ConVersionReadyFlag.
	 * On hardware that supports using the ALERT pin to toggle a
	 * GPIO a triggered buffer could be used instead.
	 * For now, we pay for that extra read of the ALERT register
	 */
	if (!chip->allow_async_readout)
		do {
			ret = regmap_read(chip->regmap, INA226_ALERT_MASK,
					  &alert);
			if (ret < 0)
				return ret;

			alert &= INA266_CVRF;
		} while (!alert);

	/*
	 * Single register reads: bulk_read will not work with ina226
	 * as there is no auto-increment of the address register for
	 * data length longer than 16bits.
	 */
	for_each_set_bit(bit, indio_dev->active_scan_mask,
			 indio_dev->masklength) {
		unsigned int val;

		ret = regmap_read(chip->regmap,
				  INA2XX_SHUNT_VOLTAGE + bit, &val);
		if (ret < 0)
			return ret;

		data[i++] = val;
	}

	time_b = iio_get_time_ns();

	iio_push_to_buffers_with_timestamp(indio_dev,
					   (unsigned int *)data, time_a);

	chip->prev_ns = time_a;

	return (unsigned long)(time_b - time_a) / 1000;
};

static int ina2xx_capture_thread(void *data)
{
	struct iio_dev *indio_dev = data;
	struct ina2xx_chip_info *chip = iio_priv(indio_dev);
	unsigned int sampling_us = SAMPLING_PERIOD(chip);
	int buffer_us;

	/*
	 * Poll a bit faster than the chip internal Fs, in case
	 * we wish to sync with the conversion ready flag.
	 */
	if (!chip->allow_async_readout)
		sampling_us -= 200;

	do {
		buffer_us = ina2xx_work_buffer(indio_dev);
		if (buffer_us < 0)
			return buffer_us;

		if (sampling_us > buffer_us)
			udelay(sampling_us - buffer_us);

	} while (!kthread_should_stop());

	return 0;
}

static int ina2xx_buffer_enable(struct iio_dev *indio_dev)
{
	struct ina2xx_chip_info *chip = iio_priv(indio_dev);
	unsigned int sampling_us = SAMPLING_PERIOD(chip);

	dev_dbg(&indio_dev->dev, "Enabling buffer w/ scan_mask %02x, freq = %d, avg =%u\n",
		(unsigned int)(*indio_dev->active_scan_mask),
		1000000 / sampling_us, chip->avg);

	dev_dbg(&indio_dev->dev, "Expected work period: %u us\n", sampling_us);
	dev_dbg(&indio_dev->dev, "Async readout mode: %d\n",
		chip->allow_async_readout);

	chip->prev_ns = iio_get_time_ns();

	chip->task = kthread_run(ina2xx_capture_thread, (void *)indio_dev,
				 "%s:%d-%uus", indio_dev->name, indio_dev->id,
				 sampling_us);

	return PTR_ERR_OR_ZERO(chip->task);
}

static int ina2xx_buffer_disable(struct iio_dev *indio_dev)
{
	struct ina2xx_chip_info *chip = iio_priv(indio_dev);

	if (chip->task) {
		kthread_stop(chip->task);
		chip->task = NULL;
	}

	return 0;
}

static const struct iio_buffer_setup_ops ina2xx_setup_ops = {
	.postenable = &ina2xx_buffer_enable,
	.predisable = &ina2xx_buffer_disable,
};

static int ina2xx_debug_reg(struct iio_dev *indio_dev,
			    unsigned reg, unsigned writeval, unsigned *readval)
{
	struct ina2xx_chip_info *chip = iio_priv(indio_dev);

	if (!readval)
		return regmap_write(chip->regmap, reg, writeval);

	return regmap_read(chip->regmap, reg, readval);
}

/* Possible integration times for vshunt and vbus */
static IIO_CONST_ATTR_INT_TIME_AVAIL("0.000140 0.000204 0.000332 0.000588 0.001100 0.002116 0.004156 0.008244");

static IIO_DEVICE_ATTR(in_allow_async_readout, S_IRUGO | S_IWUSR,
		       ina2xx_allow_async_readout_show,
		       ina2xx_allow_async_readout_store, 0);

static IIO_DEVICE_ATTR(in_shunt_resistor, S_IRUGO | S_IWUSR,
		       ina2xx_shunt_resistor_show,
		       ina2xx_shunt_resistor_store, 0);

static struct attribute *ina2xx_attributes[] = {
	&iio_dev_attr_in_allow_async_readout.dev_attr.attr,
	&iio_const_attr_integration_time_available.dev_attr.attr,
	&iio_dev_attr_in_shunt_resistor.dev_attr.attr,
	NULL,
};

static const struct attribute_group ina2xx_attribute_group = {
	.attrs = ina2xx_attributes,
};

static const struct iio_info ina2xx_info = {
	.driver_module = THIS_MODULE,
	.attrs = &ina2xx_attribute_group,
	.read_raw = ina2xx_read_raw,
	.write_raw = ina2xx_write_raw,
	.debugfs_reg_access = ina2xx_debug_reg,
};

/* Initialize the configuration and calibration registers. */
static int ina2xx_init(struct ina2xx_chip_info *chip, unsigned int config)
{
	u16 regval;
	int ret;

	ret = regmap_write(chip->regmap, INA2XX_CONFIG, config);
	if (ret)
		return ret;

	/*
	 * Set current LSB to 1mA, shunt is in uOhms
	 * (equation 13 in datasheet). We hardcode a Current_LSB
	 * of 1.0 x10-6. The only remaining parameter is RShunt.
	 * There is no need to expose the CALIBRATION register
	 * to the user for now.
	 */
	regval = DIV_ROUND_CLOSEST(chip->config->calibration_factor,
				   chip->shunt_resistor);

	return regmap_write(chip->regmap, INA2XX_CALIBRATION, regval);
}

static int ina2xx_probe(struct i2c_client *client,
			const struct i2c_device_id *id)
{
	struct ina2xx_chip_info *chip;
	struct iio_dev *indio_dev;
	struct iio_buffer *buffer;
	unsigned int val;
	int ret;

	indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*chip));
	if (!indio_dev)
		return -ENOMEM;

	chip = iio_priv(indio_dev);

	/* This is only used for device removal purposes. */
	i2c_set_clientdata(client, indio_dev);

	chip->regmap = devm_regmap_init_i2c(client, &ina2xx_regmap_config);
	if (IS_ERR(chip->regmap)) {
		dev_err(&client->dev, "failed to allocate register map\n");
		return PTR_ERR(chip->regmap);
	}

	chip->config = &ina2xx_config[id->driver_data];

	mutex_init(&chip->state_lock);

	if (of_property_read_u32(client->dev.of_node,
				 "shunt-resistor", &val) < 0) {
		struct ina2xx_platform_data *pdata =
		    dev_get_platdata(&client->dev);

		if (pdata)
			val = pdata->shunt_uohms;
		else
			val = INA2XX_RSHUNT_DEFAULT;
	}

	ret = set_shunt_resistor(chip, val);
	if (ret)
		return ret;

	/* Patch the current config register with default. */
	val = chip->config->config_default;

	if (id->driver_data == ina226) {
		ina226_set_average(chip, INA226_DEFAULT_AVG, &val);
		ina226_set_int_time_vbus(chip, INA226_DEFAULT_IT, &val);
		ina226_set_int_time_vshunt(chip, INA226_DEFAULT_IT, &val);
	}

	ret = ina2xx_init(chip, val);
	if (ret) {
		dev_err(&client->dev, "error configuring the device\n");
		return ret;
	}

	indio_dev->modes = INDIO_DIRECT_MODE | INDIO_BUFFER_SOFTWARE;
	indio_dev->dev.parent = &client->dev;
	indio_dev->channels = ina2xx_channels;
	indio_dev->num_channels = ARRAY_SIZE(ina2xx_channels);
	indio_dev->name = id->name;
	indio_dev->info = &ina2xx_info;
	indio_dev->setup_ops = &ina2xx_setup_ops;

	buffer = devm_iio_kfifo_allocate(&indio_dev->dev);
	if (!buffer)
		return -ENOMEM;

	iio_device_attach_buffer(indio_dev, buffer);

	return iio_device_register(indio_dev);
}

static int ina2xx_remove(struct i2c_client *client)
{
	struct iio_dev *indio_dev = i2c_get_clientdata(client);
	struct ina2xx_chip_info *chip = iio_priv(indio_dev);

	iio_device_unregister(indio_dev);

	/* Powerdown */
	return regmap_update_bits(chip->regmap, INA2XX_CONFIG,
				  INA2XX_MODE_MASK, 0);
}

static const struct i2c_device_id ina2xx_id[] = {
	{"ina219", ina219},
	{"ina220", ina219},
	{"ina226", ina226},
	{"ina230", ina226},
	{"ina231", ina226},
	{}
};
MODULE_DEVICE_TABLE(i2c, ina2xx_id);

static struct i2c_driver ina2xx_driver = {
	.driver = {
		   .name = KBUILD_MODNAME,
	},
	.probe = ina2xx_probe,
	.remove = ina2xx_remove,
	.id_table = ina2xx_id,
};
module_i2c_driver(ina2xx_driver);

MODULE_AUTHOR("Marc Titinger <marc.titinger@baylibre.com>");
MODULE_DESCRIPTION("Texas Instruments INA2XX ADC driver");
MODULE_LICENSE("GPL v2");