sparc: Support for GRLIB APBUART serial port
This patch adds support for the APBUART serial port from Aeroflex
Gaisler's IP library GRLIB. It is currently used in all LEON3 designs
(SPARC V8) but can be used on other platforms as well (which support OF).
Signed-off-by: Kristoffer Glembo <kristoffer@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/serial/apbuart.h b/drivers/serial/apbuart.h
new file mode 100644
index 0000000..5faf87c
--- /dev/null
+++ b/drivers/serial/apbuart.h
@@ -0,0 +1,64 @@
+#ifndef __GRLIB_APBUART_H__
+#define __GRLIB_APBUART_H__
+
+#include <asm/io.h>
+
+#define UART_NR 8
+static int grlib_apbuart_port_nr;
+
+struct grlib_apbuart_regs_map {
+ u32 data;
+ u32 status;
+ u32 ctrl;
+ u32 scaler;
+};
+
+struct amba_prom_registers {
+ unsigned int phys_addr;
+ unsigned int reg_size;
+};
+
+/*
+ * The following defines the bits in the APBUART Status Registers.
+ */
+#define UART_STATUS_DR 0x00000001 /* Data Ready */
+#define UART_STATUS_TSE 0x00000002 /* TX Send Register Empty */
+#define UART_STATUS_THE 0x00000004 /* TX Hold Register Empty */
+#define UART_STATUS_BR 0x00000008 /* Break Error */
+#define UART_STATUS_OE 0x00000010 /* RX Overrun Error */
+#define UART_STATUS_PE 0x00000020 /* RX Parity Error */
+#define UART_STATUS_FE 0x00000040 /* RX Framing Error */
+#define UART_STATUS_ERR 0x00000078 /* Error Mask */
+
+/*
+ * The following defines the bits in the APBUART Ctrl Registers.
+ */
+#define UART_CTRL_RE 0x00000001 /* Receiver enable */
+#define UART_CTRL_TE 0x00000002 /* Transmitter enable */
+#define UART_CTRL_RI 0x00000004 /* Receiver interrupt enable */
+#define UART_CTRL_TI 0x00000008 /* Transmitter irq */
+#define UART_CTRL_PS 0x00000010 /* Parity select */
+#define UART_CTRL_PE 0x00000020 /* Parity enable */
+#define UART_CTRL_FL 0x00000040 /* Flow control enable */
+#define UART_CTRL_LB 0x00000080 /* Loopback enable */
+
+#define APBBASE(port) ((struct grlib_apbuart_regs_map *)((port)->membase))
+
+#define APBBASE_DATA_P(port) (&(APBBASE(port)->data))
+#define APBBASE_STATUS_P(port) (&(APBBASE(port)->status))
+#define APBBASE_CTRL_P(port) (&(APBBASE(port)->ctrl))
+#define APBBASE_SCALAR_P(port) (&(APBBASE(port)->scaler))
+
+#define UART_GET_CHAR(port) (__raw_readl(APBBASE_DATA_P(port)))
+#define UART_PUT_CHAR(port, v) (__raw_writel(v, APBBASE_DATA_P(port)))
+#define UART_GET_STATUS(port) (__raw_readl(APBBASE_STATUS_P(port)))
+#define UART_PUT_STATUS(port, v)(__raw_writel(v, APBBASE_STATUS_P(port)))
+#define UART_GET_CTRL(port) (__raw_readl(APBBASE_CTRL_P(port)))
+#define UART_PUT_CTRL(port, v) (__raw_writel(v, APBBASE_CTRL_P(port)))
+#define UART_GET_SCAL(port) (__raw_readl(APBBASE_SCALAR_P(port)))
+#define UART_PUT_SCAL(port, v) (__raw_writel(v, APBBASE_SCALAR_P(port)))
+
+#define UART_RX_DATA(s) (((s) & UART_STATUS_DR) != 0)
+#define UART_TX_READY(s) (((s) & UART_STATUS_THE) != 0)
+
+#endif /* __GRLIB_APBUART_H__ */