staging: wilc1000: wilc_wlan_if.h: remove warnings line over 80 characters
This patch removes the warnings reported by checkpatch.pl for line over 80
characters. And also align comments which is not over 80 but to align with them.
Signed-off-by: Leo Kim <leo.kim@atmel.com>
Signed-off-by: Glen Lee <glen.lee@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
diff --git a/drivers/staging/wilc1000/wilc_wlan_if.h b/drivers/staging/wilc1000/wilc_wlan_if.h
index e56014d..0863592 100644
--- a/drivers/staging/wilc1000/wilc_wlan_if.h
+++ b/drivers/staging/wilc1000/wilc_wlan_if.h
@@ -1,4 +1,4 @@
-/* ////////////////////////////////////////////////////////////////////////// */
+/* ///////////////////////////////////////////////////////////////////////// */
/* */
/* Copyright (c) Atmel Corporation. All rights reserved. */
/* */
@@ -165,7 +165,8 @@
int (*wlan_cfg_set)(int, u32, u8 *, u32, int, u32);
int (*wlan_cfg_get)(int, u32, int, u32);
int (*wlan_cfg_get_value)(u32, u8 *, u32);
- int (*wlan_add_mgmt_to_tx_que)(void *, u8 *, u32, wilc_tx_complete_func_t);
+ int (*wlan_add_mgmt_to_tx_que)(void *, u8 *, u32,
+ wilc_tx_complete_func_t);
} wilc_wlan_oup_t;
/********************************************
@@ -213,16 +214,16 @@
} TX_RATE_T;
typedef enum {
- B_ONLY_MODE = 0, /* basic rate: 1, 2 Mbps, otherwise: 5, 11 Mbps */
- G_ONLY_MODE, /* basic rate: 6, 12, 24 Mbps, otherwise: 9, 18, 36, 48, 54 Mbps */
- G_MIXED_11B_1_MODE, /* basic rate: 1, 2, 5.5, 11 Mbps, otherwise: all on */
- G_MIXED_11B_2_MODE, /* basic rate: 1, 2, 5, 11, 6, 12, 24 Mbps, otherwise: all on */
+ B_ONLY_MODE = 0, /* 1, 2 M, otherwise: 5, 11 M */
+ G_ONLY_MODE, /* 6, 12, 24 M, otherwise: 9, 18, 36, 48, 54 M */
+ G_MIXED_11B_1_MODE, /* 1, 2, 5.5, 11 M, otherwise: all on */
+ G_MIXED_11B_2_MODE, /* 1, 2, 5, 11, 6, 12, 24 M, otherwise: all on */
} G_OPERATING_MODE_T;
typedef enum {
- G_SHORT_PREAMBLE = 0, /* Short Preamble */
- G_LONG_PREAMBLE = 1, /* Long Preamble */
- G_AUTO_PREAMBLE = 2, /* Auto Preamble Selection */
+ G_SHORT_PREAMBLE = 0, /* Short Preamble */
+ G_LONG_PREAMBLE = 1, /* Long Preamble */
+ G_AUTO_PREAMBLE = 2, /* Auto Preamble Selection */
} G_PREAMBLE_T;
#define MAC_CONNECTED 1
@@ -345,10 +346,10 @@
} N_OBSS_DETECTION_T;
typedef enum {
- RTS_CTS_NONHT_PROT = 0, /* RTS-CTS at non-HT rate */
- FIRST_FRAME_NONHT_PROT, /* First frame at non-HT rate */
- LSIG_TXOP_PROT, /* LSIG TXOP Protection */
- FIRST_FRAME_MIXED_PROT, /* First frame at Mixed format */
+ RTS_CTS_NONHT_PROT = 0, /* RTS-CTS at non-HT rate */
+ FIRST_FRAME_NONHT_PROT, /* First frame at non-HT rate */
+ LSIG_TXOP_PROT, /* LSIG TXOP Protection */
+ FIRST_FRAME_MIXED_PROT, /* First frame at Mixed format */
} N_PROTECTION_TYPE_T;
typedef enum {
@@ -383,237 +384,298 @@
typedef enum {
WID_NIL = 0xffff,
- /* BSS Type */
- /* -------------------------------------------------------------- */
- /* Configuration : Infrastructure Independent Access Point */
- /* Values to set : 0 1 2 */
- /* -------------------------------------------------------------- */
+ /*
+ * BSS Type
+ * -----------------------------------------------------------
+ * Configuration : Infrastructure Independent Access Point
+ * Values to set : 0 1 2
+ * -----------------------------------------------------------
+ */
WID_BSS_TYPE = 0x0000,
- /* Transmit Rate */
- /* -------------------------------------------------------------- */
- /* Configuration : 1 2 5.5 11 6 9 12 18 24 36 48 54 */
- /* Values to set : 1 2 5 11 6 9 12 18 24 36 48 54 */
- /* -------------------------------------------------------------- */
+ /*
+ * Transmit Rate
+ * -----------------------------------------------------------
+ * Configuration : 1 2 5.5 11 6 9 12 18 24 36 48 54
+ * Values to set : 1 2 5 11 6 9 12 18 24 36 48 54
+ * -----------------------------------------------------------
+ */
WID_CURRENT_TX_RATE = 0x0001,
- /* Channel */
- /* ------------------------------------------------------------------- */
- /* Configuration(g) : 1 2 3 4 5 6 7 8 9 10 11 12 13 14 */
- /* Values to set : 1 2 3 4 5 6 7 8 9 10 11 12 13 14 */
- /* -------------------------------------------------------------------- */
+ /*
+ * Channel
+ * -----------------------------------------------------------
+ * Configuration(g) : 1 2 3 4 5 6 7 8 9 10 11 12 13 14
+ * Values to set : 1 2 3 4 5 6 7 8 9 10 11 12 13 14
+ * -----------------------------------------------------------
+ */
WID_CURRENT_CHANNEL = 0x0002,
- /* Preamble */
- /* -------------------------------------------------------------- */
- /* Configuration : short long Auto */
- /* Values to set : 0 1 2 */
- /* -------------------------------------------------------------- */
+ /*
+ * Preamble
+ * -----------------------------------------------------------
+ * Configuration : short long Auto
+ * Values to set : 0 1 2
+ * -----------------------------------------------------------
+ */
WID_PREAMBLE = 0x0003,
- /* 11g operating mode (ignored if 11g not present) */
- /* -------------------------------------------------------------- */
- /* Configuration : HighPerf Compat(RSet #1) Compat(RSet #2) */
- /* Values to set : 1 2 3 */
- /* -------------------------------------------------------------- */
+ /*
+ * 11g operating mode (ignored if 11g not present)
+ * -----------------------------------------------------------
+ * Configuration : HighPerf Compat(RSet #1) Compat(RSet #2)
+ * Values to set : 1 2 3
+ * -----------------------------------------------------------
+ */
WID_11G_OPERATING_MODE = 0x0004,
- /* Mac status (response only) */
- /* -------------------------------------------------------------- */
- /* Configuration : disconnect connect */
- /* Values to get : 0 1 */
- /* -------------------------------------------------------------- */
+ /*
+ * Mac status (response only)
+ * -----------------------------------------------------------
+ * Configuration : disconnect connect
+ * Values to get : 0 1
+ * -----------------------------------------------------------
+ */
WID_STATUS = 0x0005,
- /* Scan type */
- /* -------------------------------------------------------------- */
- /* Configuration : Passive Scanning Active Scanning */
- /* Values to set : 0 1 */
- /* -------------------------------------------------------------- */
+ /*
+ * Scan type
+ * -----------------------------------------------------------
+ * Configuration : Passive Scanning Active Scanning
+ * Values to set : 0 1
+ * -----------------------------------------------------------
+ */
WID_SCAN_TYPE = 0x0007,
- /* Key Id (WEP default key Id) */
- /* -------------------------------------------------------------- */
- /* Configuration : Any value between 0 to 3 */
- /* Values to set : Same value. Default is 0 */
- /* -------------------------------------------------------------- */
+ /*
+ * Key Id (WEP default key Id)
+ * -----------------------------------------------------------
+ * Configuration : Any value between 0 to 3
+ * Values to set : Same value. Default is 0
+ * -----------------------------------------------------------
+ */
WID_KEY_ID = 0x0009,
- /* QoS Enable */
- /* -------------------------------------------------------------- */
- /* Configuration : QoS Disable WMM Enable */
- /* Values to set : 0 1 */
- /* -------------------------------------------------------------- */
+ /*
+ * QoS Enable
+ * -----------------------------------------------------------
+ * Configuration : QoS Disable WMM Enable
+ * Values to set : 0 1
+ * -----------------------------------------------------------
+ */
WID_QOS_ENABLE = 0x000A,
- /* Power Management */
- /* ------------------------------------------------------------------ */
- /* Configuration : NO_POWERSAVE MIN_POWERSAVE MAX_POWERSAVE */
- /* Values to set : 0 1 2 */
- /* ------------------------------------------------------------------ */
+ /*
+ * Power Management
+ * -----------------------------------------------------------
+ * Configuration : NO_POWERSAVE MIN_POWERSAVE MAX_POWERSAVE
+ * Values to set : 0 1 2
+ * -----------------------------------------------------------
+ */
WID_POWER_MANAGEMENT = 0x000B,
- /* WEP/802 11I Configuration */
- /* ------------------------------------------------------------------ */
- /* Configuration : Disable WP40 WP104 WPA-AES WPA-TKIP RSN-AES RSN-TKIP */
- /* Values (0x) : 00 03 07 29 49 31 51 */
- /* */
- /* Configuration : WPA-AES+TKIP RSN-AES+TKIP */
- /* Values (0x) : 69 71 */
- /* ------------------------------------------------------------------ */
+ /*
+ * WEP/802 11I Configuration
+ * -----------------------------------------------------------
+ * Configuration:Disable WP40 WP104 WPA-AES WPA-TKIP RSN-AES RSN-TKIP
+ * Values (0x) : 00 03 07 29 49 31 51
+ * Configuration:WPA-AES+TKIP RSN-AES+TKIP
+ * Values (0x) : 69 71
+ * -----------------------------------------------------------
+ */
WID_11I_MODE = 0x000C,
- /* WEP Configuration: Used in BSS STA mode only when WEP is enabled */
- /* ------------------------------------------------------------------ */
- /* Configuration : Open System Shared Key Any Type | 802.1x Auth */
- /* Values (0x) : 01 02 03 | BIT2 */
- /* ------------------------------------------------------------------ */
+ /*
+ * WEP Configuration: Used in BSS STA mode only when WEP is enabled
+ * -----------------------------------------------------------
+ * Configuration : Open System Shared Key Any Type | 802.1x Auth
+ * Values (0x) : 01 02 03 | BIT2
+ * -----------------------------------------------------------
+ */
WID_AUTH_TYPE = 0x000D,
- /* Site Survey Type */
- /* -------------------------------------------------------------- */
- /* Configuration : Values to set */
- /* Survey 1 Channel : 0 */
- /* survey all Channels : 1 */
- /* Disable Site Survey : 2 */
- /* -------------------------------------------------------------- */
+ /*
+ * Site Survey Type
+ * -----------------------------------------------------------
+ * Configuration : Values to set
+ * Survey 1 Channel : 0
+ * survey all Channels : 1
+ * Disable Site Survey : 2
+ * -----------------------------------------------------------
+ */
WID_SITE_SURVEY = 0x000E,
- /* Listen Interval */
- /* -------------------------------------------------------------- */
- /* Configuration : Any value between 1 to 255 */
- /* Values to set : Same value. Default is 3 */
- /* -------------------------------------------------------------- */
+ /*
+ * Listen Interval
+ * -----------------------------------------------------------
+ * Configuration : Any value between 1 to 255
+ * Values to set : Same value. Default is 3
+ * -----------------------------------------------------------
+ */
WID_LISTEN_INTERVAL = 0x000F,
- /* DTIM Period */
- /* -------------------------------------------------------------- */
- /* Configuration : Any value between 1 to 255 */
- /* Values to set : Same value. Default is 3 */
- /* -------------------------------------------------------------- */
+ /*
+ * DTIM Period
+ * -----------------------------------------------------------
+ * Configuration : Any value between 1 to 255
+ * Values to set : Same value. Default is 3
+ * -----------------------------------------------------------
+ */
WID_DTIM_PERIOD = 0x0010,
- /* ACK Policy */
- /* -------------------------------------------------------------- */
- /* Configuration : Normal Ack No Ack */
- /* Values to set : 0 1 */
- /* -------------------------------------------------------------- */
+ /*
+ * ACK Policy
+ * -----------------------------------------------------------
+ * Configuration : Normal Ack No Ack
+ * Values to set : 0 1
+ * -----------------------------------------------------------
+ */
WID_ACK_POLICY = 0x0011,
- /* Reset MAC (Set only) */
- /* -------------------------------------------------------------- */
- /* Configuration : Don't Reset Reset No Request */
- /* Values to set : 0 1 2 */
- /* -------------------------------------------------------------- */
+ /*
+ * Reset MAC (Set only)
+ * -----------------------------------------------------------
+ * Configuration : Don't Reset Reset No Request
+ * Values to set : 0 1 2
+ * -----------------------------------------------------------
+ */
WID_RESET = 0x0012,
- /* Broadcast SSID Option: Setting this will adhere to "" SSID element */
- /* ------------------------------------------------------------------ */
- /* Configuration : Enable Disable */
- /* Values to set : 1 0 */
- /* ------------------------------------------------------------------ */
+ /*
+ * Broadcast SSID Option: Setting this will adhere to "" SSID element
+ * -----------------------------------------------------------
+ * Configuration : Enable Disable
+ * Values to set : 1 0
+ * -----------------------------------------------------------
+ */
WID_BCAST_SSID = 0x0015,
- /* Disconnect (Station) */
- /* ------------------------------------------------------------------ */
- /* Configuration : Association ID */
- /* Values to set : Association ID */
- /* ------------------------------------------------------------------ */
+ /*
+ * Disconnect (Station)
+ * -----------------------------------------------------------
+ * Configuration : Association ID
+ * Values to set : Association ID
+ * -----------------------------------------------------------
+ */
WID_DISCONNECT = 0x0016,
- /* 11a Tx Power Level */
- /* -------------------------------------------------------------------- */
- /* Configuration : Sets TX Power (Higher the value greater the power) */
- /* Values to set : Any value between 0 and 63 (inclusive; Default is 48)*/
- /* -------------------------------------------------------------------- */
+ /*
+ * 11a Tx Power Level
+ * -----------------------------------------------------------
+ * Configuration : Sets TX Power (Higher the value greater the power)
+ * Values to set : Any value between 0 and 63 (inclusive Default 48)
+ * -----------------------------------------------------------
+ */
WID_TX_POWER_LEVEL_11A = 0x0018,
- /* Group Key Update Policy Selection */
- /* -------------------------------------------------------------------- */
- /* Configuration : Disabled timeBased packetBased timePacketBased */
- /* Values to set : 1 2 3 4 */
- /* -------------------------------------------------------------------- */
+ /*
+ * Group Key Update Policy Selection
+ * -----------------------------------------------------------
+ * Configuration : Disabled timeBased packetBased timePacketBased
+ * Values to set : 1 2 3 4
+ * -----------------------------------------------------------
+ */
WID_REKEY_POLICY = 0x0019,
- /* Allow Short Slot */
- /* -------------------------------------------------------------- */
- /* Configuration : Disallow Short Slot Allow Short Slot */
- /* (Enable Only Long Slot) (Enable Short Slot if applicable)*/
- /* Values to set : 0 1 */
- /* -------------------------------------------------------------- */
+ /*
+ * Allow Short Slot
+ * -----------------------------------------------------------
+ * Configuration : Disallow Short Slot Allow Short Slot
+ * (Enable Only Long Slot) (Enable Short Slot if applicable)
+ * Values to set : 0 1
+ * -----------------------------------------------------------
+ */
WID_SHORT_SLOT_ALLOWED = 0x001A,
WID_PHY_ACTIVE_REG = 0x001B,
- /* 11b Tx Power Level */
- /* -------------------------------------------------------------------- */
- /* Configuration : Sets TX Power (Higher the value greater the power) */
- /* Values to set : Any value between 0 and 63 (inclusive; Default is 48)*/
- /* -------------------------------------------------------------------- */
+ /*
+ * 11b Tx Power Level
+ * -----------------------------------------------------------
+ * Configuration : Sets TX Power (Higher the value greater the power)
+ * Values to set : Any value between 0 and 63 (inclusive Default 48)
+ * -----------------------------------------------------------
+ */
WID_TX_POWER_LEVEL_11B = 0x001D,
- /* Scan Request */
- /* -------------------------------------------------------------------- */
- /* Configuration : Request default scan */
- /* Values to set : 0 */
- /* -------------------------------------------------------------------- */
+ /*
+ * Scan Request
+ * -----------------------------------------------------------
+ * Configuration : Request default scan
+ * Values to set : 0
+ * -----------------------------------------------------------
+ */
WID_START_SCAN_REQ = 0x001E,
- /* Rssi (get only) */
- /* -------------------------------------------------------------------- */
- /* Configuration : */
- /* Values to get : Rssi value */
- /* -------------------------------------------------------------------- */
+ /*
+ * Rssi (get only)
+ * -----------------------------------------------------------
+ * Configuration :
+ * Values to get : Rssi value
+ * -----------------------------------------------------------
+ */
WID_RSSI = 0x001F,
- /* Join Request */
- /* -------------------------------------------------------------------- */
- /* Configuration : Request to join */
- /* Values to set : index of scan result */
- /* -------------------------------------------------------------------- */
+ /*
+ * Join Request
+ * -----------------------------------------------------------
+ * Configuration : Request to join
+ * Values to set : index of scan result
+ * -----------------------------------------------------------
+ */
WID_JOIN_REQ = 0x0020,
- WID_LINKSPEED = 0x0026,
+ WID_LINKSPEED = 0x0026,
- /* Enable User Control of TX Power */
- /* -------------------------------------------------------------------- */
- /* Configuration : Disable Enable */
- /* Values to set : 0 1 */
- /* -------------------------------------------------------------------- */
+ /*
+ * Enable User Control of TX Power
+ * -----------------------------------------------------------
+ * Configuration : Disable Enable
+ * Values to set : 0 1
+ * -----------------------------------------------------------
+ */
WID_USER_CONTROL_ON_TX_POWER = 0x0027,
WID_MEMORY_ACCESS_8BIT = 0x0029,
- /* Enable Auto RX Sensitivity feature */
- /* -------------------------------------------------------------------- */
- /* Configuration : Disable Enable */
- /* Values to set : 0 1 */
- /* -------------------------------------------------------------------- */
+ /*
+ * Enable Auto RX Sensitivity feature
+ * -----------------------------------------------------------
+ * Configuration : Disable Enable
+ * Values to set : 0 1
+ * -----------------------------------------------------------
+ */
WID_AUTO_RX_SENSITIVITY = 0x0032,
- /* Receive Buffer Based Ack */
- /* -------------------------------------------------------------------- */
- /* Configuration : Disable Enable */
- /* Values to set : 0 1 */
- /* -------------------------------------------------------------------- */
+ /*
+ * Receive Buffer Based Ack
+ * -----------------------------------------------------------
+ * Configuration : Disable Enable
+ * Values to set : 0 1
+ * -----------------------------------------------------------
+ */
WID_DATAFLOW_CONTROL = 0x0033,
- /* Scan Filter */
- /* -------------------------------------------------------------------- */
- /* Configuration : Class No filter AP only Station Only */
- /* Values to set : 0 1 2 */
- /* Configuration : Priority High Rssi Low Rssi Detect */
- /* Values to set : 0 0x4 0x08 */
- /* Configuration : Channel filter off filter on */
- /* Values to set : 0 0x10 */
- /* -------------------------------------------------------------------- */
+ /*
+ * Scan Filter
+ * -----------------------------------------------------------
+ * Configuration : Class No filter AP only Station Only
+ * Values to set : 0 1 2
+ * Configuration : Priority High Rssi Low Rssi Detect
+ * Values to set : 0 0x4 0x0
+ * Configuration : Channel filter off filter on
+ * Values to set : 0 0x10
+ * -----------------------------------------------------------
+ */
WID_SCAN_FILTER = 0x0036,
- /* Link Loss Threshold (measure in the beacon period) */
- /* -------------------------------------------------------------------- */
- /* Configuration : Any value between 10 and 254 (Set to 255 to disable it) */
- /* Values to set : Same value. Default is 10 */
- /* -------------------------------------------------------------------- */
+ /*
+ * Link Loss Threshold (measure in the beacon period)
+ * -----------------------------------------------------------
+ * Configuration : Any value between 10 and 254(Set to 255 disable)
+ * Values to set : Same value. Default is 10
+ * -----------------------------------------------------------
+ */
WID_LINK_LOSS_THRESHOLD = 0x0037,
WID_ABORT_RUNNING_SCAN = 0x003E,
@@ -621,103 +683,127 @@
/* NMAC Character WID list */
WID_WPS_START = 0x0043,
- /* Protection mode for MAC */
- /* -------------------------------------------------------------- */
- /* Configuration : Auto No protection ERP HT GF */
- /* Values to set : 0 1 2 3 4 */
- /* -------------------------------------------------------------- */
+ /*
+ * Protection mode for MAC
+ * -----------------------------------------------------------
+ * Configuration : Auto No protection ERP HT GF
+ * Values to set : 0 1 2 3 4
+ * -----------------------------------------------------------
+ */
WID_11N_PROT_MECH = 0x0080,
- /* ERP Protection type for MAC */
- /* -------------------------------------------------------------- */
- /* Configuration : Self-CTS RTS-CTS */
- /* Values to set : 0 1 */
- /* -------------------------------------------------------------- */
+ /*
+ * ERP Protection type for MAC
+ * -----------------------------------------------------------
+ * Configuration : Self-CTS RTS-CTS
+ * Values to set : 0 1
+ * -----------------------------------------------------------
+ */
WID_11N_ERP_PROT_TYPE = 0x0081,
- /* HT Option Enable */
- /* -------------------------------------------------------------- */
- /* Configuration : HT Enable HT Disable */
- /* Values to set : 1 0 */
- /* -------------------------------------------------------------- */
+ /*
+ * HT Option Enable
+ * -----------------------------------------------------------
+ * Configuration : HT Enable HT Disable
+ * Values to set : 1 0
+ * -----------------------------------------------------------
+ */
WID_11N_ENABLE = 0x0082,
- /* 11n Operating mode (Note that 11g operating mode will also be */
- /* used in addition to this, if this is set to HT Mixed mode) */
- /* -------------------------------------------------------------- */
- /* Configuration : HT Mixed HT Only-20MHz HT Only-20/40MHz */
- /* Values to set : 1 2 3 */
- /* -------------------------------------------------------------- */
+ /*
+ * 11n Operating mode (Note that 11g operating mode will also be
+ * used in addition to this, if this is set to HT Mixed mode)
+ * -----------------------------------------------------------
+ * Configuration : HT Mixed HT Only-20MHz HT Only-20/40MHz
+ * Values to set : 1 2 3
+ * -----------------------------------------------------------
+ */
WID_11N_OPERATING_MODE = 0x0083,
- /* 11n OBSS non-HT STA Detection flag */
- /* -------------------------------------------------------------- */
- /* Configuration : Do not detect */
- /* Values to set : 0 */
- /* Configuration : Detect, do not protect or report */
- /* Values to set : 1 */
- /* Configuration : Detect, protect and do not report */
- /* Values to set : 2 */
- /* Configuration : Detect, protect and report to other BSS */
- /* Values to set : 3 */
- /* -------------------------------------------------------------- */
+ /*
+ * 11n OBSS non-HT STA Detection flag
+ * -----------------------------------------------------------
+ * Configuration : Do not detect
+ * Values to set : 0
+ * Configuration : Detect, do not protect or report
+ * Values to set : 1
+ * Configuration : Detect, protect and do not report
+ * Values to set : 2
+ * Configuration : Detect, protect and report to other BSS
+ * Values to set : 3
+ * -----------------------------------------------------------
+ */
WID_11N_OBSS_NONHT_DETECTION = 0x0084,
- /* 11n HT Protection Type */
- /* -------------------------------------------------------------- */
- /* Configuration : RTS-CTS First Frame Exchange at non-HT-rate */
- /* Values to set : 0 1 */
- /* Configuration : LSIG TXOP First Frame Exchange in Mixed Fmt */
- /* Values to set : 2 3 */
- /* -------------------------------------------------------------- */
+ /*
+ * 11n HT Protection Type
+ * -----------------------------------------------------------
+ * Configuration : RTS-CTS First Frame Exchange at non-HT-rate
+ * Values to set : 0 1
+ * Configuration : LSIG TXOP First Frame Exchange in Mixed Fmt
+ * Values to set : 2 3
+ * -----------------------------------------------------------
+ */
WID_11N_HT_PROT_TYPE = 0x0085,
- /* 11n RIFS Protection Enable Flag */
- /* -------------------------------------------------------------- */
- /* Configuration : Disable Enable */
- /* Values to set : 0 1 */
- /* -------------------------------------------------------------- */
+ /*
+ * 11n RIFS Protection Enable Flag
+ * -----------------------------------------------------------
+ * Configuration : Disable Enable
+ * Values to set : 0 1
+ * -----------------------------------------------------------
+ */
WID_11N_RIFS_PROT_ENABLE = 0x0086,
- /* SMPS Mode */
- /* -------------------------------------------------------------- */
- /* Configuration : Static Dynamic MIMO (Power Save Disabled) */
- /* Values to set : 1 2 3 */
- /* -------------------------------------------------------------- */
+ /*
+ * SMPS Mode
+ * -----------------------------------------------------------
+ * Configuration : Static Dynamic MIMO (Power Save Disabled)
+ * Values to set : 1 2 3
+ * -----------------------------------------------------------
+ */
WID_11N_SMPS_MODE = 0x0087,
- /* Current transmit MCS */
- /* -------------------------------------------------------------- */
- /* Configuration : MCS Index for data rate */
- /* Values to set : 0 to 7 */
- /* -------------------------------------------------------------- */
+ /*
+ * Current transmit MCS
+ * -----------------------------------------------------------
+ * Configuration : MCS Index for data rate
+ * Values to set : 0 to 7
+ * -----------------------------------------------------------
+ */
WID_11N_CURRENT_TX_MCS = 0x0088,
WID_11N_PRINT_STATS = 0x0089,
- /* 11n Short GI Enable Flag */
- /* -------------------------------------------------------------- */
- /* Configuration : Disable Enable */
- /* Values to set : 0 1 */
- /* -------------------------------------------------------------- */
+ /*
+ * 11n Short GI Enable Flag
+ * -----------------------------------------------------------
+ * Configuration : Disable Enable
+ * Values to set : 0 1
+ * -----------------------------------------------------------
+ */
WID_11N_SHORT_GI_ENABLE = 0x008D,
- /* 11n RIFS Enable Flag */
- /* -------------------------------------------------------------- */
- /* Configuration : Disable Enable */
- /* Values to set : 0 1 */
- /* -------------------------------------------------------------- */
+ /*
+ * 11n RIFS Enable Flag
+ * -----------------------------------------------------------
+ * Configuration : Disable Enable
+ * Values to set : 0 1
+ * -----------------------------------------------------------
+ */
WID_RIFS_MODE = 0x0094,
- /* TX Abort Feature */
- /* -------------------------------------------------------------- */
- /* Configuration : Disable Self CTS Enable Self CTS */
- /* Values to set : 0 1 */
- /* Configuration : Disable TX Abort Enable TX Abort */
- /* Values to set : 2 3 */
- /* Configuration : Enable HW TX Abort Enable SW TX Abort */
- /* Values to set : 4 5 */
- /* -------------------------------------------------------------- */
+ /*
+ * TX Abort Feature
+ * -----------------------------------------------------------
+ * Configuration : Disable Self CTS Enable Self CTS
+ * Values to set : 0 1
+ * Configuration : Disable TX Abort Enable TX Abort
+ * Values to set : 2 3
+ * Configuration : Enable HW TX Abort Enable SW TX Abort
+ * Values to set : 4 5
+ * -----------------------------------------------------------
+ */
WID_TX_ABORT_CONFIG = 0x00A1,
WID_REG_TSSI_11B_VALUE = 0x00A6,
@@ -728,18 +814,22 @@
WID_DSCR_TSSI_11G_VALUE = 0x00AB,
WID_DSCR_TSSI_11N_VALUE = 0x00AC,
- /* Immediate Block-Ack Support */
- /* -------------------------------------------------------------- */
- /* Configuration : Disable Enable */
- /* Values to set : 0 1 */
- /* -------------------------------------------------------------- */
+ /*
+ * Immediate Block-Ack Support
+ * -----------------------------------------------------------
+ * Configuration : Disable Enable
+ * Values to set : 0 1
+ * -----------------------------------------------------------
+ */
WID_11N_IMMEDIATE_BA_ENABLED = 0x00AF,
- /* TXOP Disable Flag */
- /* -------------------------------------------------------------- */
- /* Configuration : Disable Enable */
- /* Values to set : 1 0 */
- /* -------------------------------------------------------------- */
+ /*
+ * TXOP Disable Flag
+ * -----------------------------------------------------------
+ * Configuration : Disable Enable
+ * Values to set : 1 0
+ * -----------------------------------------------------------
+ */
WID_11N_TXOP_PROT_DISABLE = 0x00B0,
WID_TX_POWER_LEVEL_11N = 0x00B1,
@@ -752,19 +842,23 @@
WID_DEL_BEACON = 0x00CA,
WID_LOGTerminal_Switch = 0x00CD,
- /* EMAC Short WID list */
- /* RTS Threshold */
- /* -------------------------------------------------------------- */
- /* Configuration : Any value between 256 to 2347 */
- /* Values to set : Same value. Default is 2347 */
- /* -------------------------------------------------------------- */
+ /* EMAC Short WID list */
+ /* RTS Threshold */
+ /*
+ * -----------------------------------------------------------
+ * Configuration : Any value between 256 to 2347
+ * Values to set : Same value. Default is 2347
+ * -----------------------------------------------------------
+ */
WID_RTS_THRESHOLD = 0x1000,
- /* Fragmentation Threshold */
- /* -------------------------------------------------------------- */
- /* Configuration : Any value between 256 to 2346 */
- /* Values to set : Same value. Default is 2346 */
- /* -------------------------------------------------------------- */
+ /*
+ * Fragmentation Threshold
+ * -----------------------------------------------------------
+ * Configuration : Any value between 256 to 2346
+ * Values to set : Same value. Default is 2346
+ * -----------------------------------------------------------
+ */
WID_FRAG_THRESHOLD = 0x1001,
WID_SHORT_RETRY_LIMIT = 0x1002,
@@ -849,9 +943,9 @@
WID_ASSOC_REQ_INFO = 0x301F,
WID_ASSOC_RES_INFO = 0x3020,
WID_MANUFACTURER = 0x3026, /*Added for CAPI tool */
- WID_MODEL_NAME = 0x3027, /*Added for CAPI tool */
+ WID_MODEL_NAME = 0x3027, /*Added for CAPI tool */
WID_MODEL_NUM = 0x3028, /*Added for CAPI tool */
- WID_DEVICE_NAME = 0x3029, /*Added for CAPI tool */
+ WID_DEVICE_NAME = 0x3029, /*Added for CAPI tool */
/* NMAC String WID list */
WID_11N_P_ACTION_REQ = 0x3080,