spi: dw-pci: describe Intel MID controllers better
There are more that one SPI controller on the Intel MID boards. This patch
describes the status and IDs of them. From now on we also have to care about
bus number that must be unique per host.
According to the specification the SPI1 has 5 bits for chip selects and SPI2
only 2 bits. The patch makes it depend to PCI ID.
The first controller (SPI1) is DMA capable, meanwhile SPI2 can share same
channels (via software switch) such functionality is not in the scope of this
patch. Thus, attempt to init DMA for SPI2 will always fail for now.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
diff --git a/drivers/spi/spi-dw-pci.c b/drivers/spi/spi-dw-pci.c
index ba68da1..64f3efa 100644
--- a/drivers/spi/spi-dw-pci.c
+++ b/drivers/spi/spi-dw-pci.c
@@ -30,10 +30,20 @@
struct spi_pci_desc {
int (*setup)(struct dw_spi *);
+ u16 num_cs;
+ u16 bus_num;
};
-static struct spi_pci_desc spi_pci_mid_desc = {
+static struct spi_pci_desc spi_pci_mid_desc_1 = {
.setup = dw_spi_mid_init,
+ .num_cs = 32,
+ .bus_num = 0,
+};
+
+static struct spi_pci_desc spi_pci_mid_desc_2 = {
+ .setup = dw_spi_mid_init,
+ .num_cs = 4,
+ .bus_num = 1,
};
static int spi_pci_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
@@ -65,18 +75,23 @@
dws->regs = pcim_iomap_table(pdev)[pci_bar];
- dws->bus_num = 0;
- dws->num_cs = 4;
dws->irq = pdev->irq;
/*
* Specific handling for paltforms, like dma setup,
* clock rate, FIFO depth.
*/
- if (desc && desc->setup) {
- ret = desc->setup(dws);
- if (ret)
- return ret;
+ if (desc) {
+ if (desc->setup) {
+ ret = desc->setup(dws);
+ if (ret)
+ return ret;
+ }
+
+ dws->num_cs = desc->num_cs;
+ dws->bus_num = desc->bus_num;
+ } else {
+ return -ENODEV;
}
ret = dw_spi_add_host(&pdev->dev, dws);
@@ -121,7 +136,14 @@
static const struct pci_device_id pci_ids[] = {
/* Intel MID platform SPI controller 0 */
- { PCI_VDEVICE(INTEL, 0x0800), (kernel_ulong_t)&spi_pci_mid_desc},
+ /*
+ * The access to the device 8086:0801 is disabled by HW, since it's
+ * exclusively used by SCU to communicate with MSIC.
+ */
+ /* Intel MID platform SPI controller 1 */
+ { PCI_VDEVICE(INTEL, 0x0800), (kernel_ulong_t)&spi_pci_mid_desc_1},
+ /* Intel MID platform SPI controller 2 */
+ { PCI_VDEVICE(INTEL, 0x0812), (kernel_ulong_t)&spi_pci_mid_desc_2},
{},
};