blob: 1fb34f375b22ca8c088319b3c0bfec2e896b9730 [file] [log] [blame]
/*
* Copyright (C) 2009 Eric Benard - eric@eukrea.com
*
* Based on pcm970-baseboard.c which is :
* Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de)
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation; either version 2
* of the License, or (at your option) any later version.
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
* MA 02110-1301, USA.
*/
#include <linux/gpio.h>
#include <linux/irq.h>
#include <linux/platform_device.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
#include <asm/mach/arch.h>
#include <mach/common.h>
#include <mach/iomux-mx27.h>
#include <mach/imxfb.h>
#include <mach/hardware.h>
#include <mach/mmc.h>
#include "devices-imx27.h"
#include "devices.h"
static int eukrea_mbimx27_pins[] = {
/* UART2 */
PE3_PF_UART2_CTS,
PE4_PF_UART2_RTS,
PE6_PF_UART2_TXD,
PE7_PF_UART2_RXD,
/* UART3 */
PE8_PF_UART3_TXD,
PE9_PF_UART3_RXD,
PE10_PF_UART3_CTS,
PE11_PF_UART3_RTS,
/* UART4 */
PB26_AF_UART4_RTS,
PB28_AF_UART4_TXD,
PB29_AF_UART4_CTS,
PB31_AF_UART4_RXD,
/* SDHC1*/
PE18_PF_SD1_D0,
PE19_PF_SD1_D1,
PE20_PF_SD1_D2,
PE21_PF_SD1_D3,
PE22_PF_SD1_CMD,
PE23_PF_SD1_CLK,
/* display */
PA5_PF_LSCLK,
PA6_PF_LD0,
PA7_PF_LD1,
PA8_PF_LD2,
PA9_PF_LD3,
PA10_PF_LD4,
PA11_PF_LD5,
PA12_PF_LD6,
PA13_PF_LD7,
PA14_PF_LD8,
PA15_PF_LD9,
PA16_PF_LD10,
PA17_PF_LD11,
PA18_PF_LD12,
PA19_PF_LD13,
PA20_PF_LD14,
PA21_PF_LD15,
PA22_PF_LD16,
PA23_PF_LD17,
PA28_PF_HSYNC,
PA29_PF_VSYNC,
PA30_PF_CONTRAST,
PA31_PF_OE_ACD,
/* SPI1 */
PD28_PF_CSPI1_SS0,
PD29_PF_CSPI1_SCLK,
PD30_PF_CSPI1_MISO,
PD31_PF_CSPI1_MOSI,
};
static struct gpio_led gpio_leds[] = {
{
.name = "led1",
.default_trigger = "heartbeat",
.active_low = 1,
.gpio = GPIO_PORTF | 16,
},
{
.name = "led2",
.default_trigger = "none",
.active_low = 1,
.gpio = GPIO_PORTF | 19,
},
{
.name = "backlight",
.default_trigger = "backlight",
.active_low = 0,
.gpio = GPIO_PORTE | 5,
},
};
static struct gpio_led_platform_data gpio_led_info = {
.leds = gpio_leds,
.num_leds = ARRAY_SIZE(gpio_leds),
};
static struct platform_device leds_gpio = {
.name = "leds-gpio",
.id = -1,
.dev = {
.platform_data = &gpio_led_info,
},
};
static struct imx_fb_videomode eukrea_mbimx27_modes[] = {
{
.mode = {
.name = "CMO-QGVA",
.refresh = 60,
.xres = 320,
.yres = 240,
.pixclock = 156000,
.hsync_len = 30,
.left_margin = 38,
.right_margin = 20,
.vsync_len = 3,
.upper_margin = 15,
.lower_margin = 4,
},
.pcr = 0xFAD08B80,
.bpp = 16,
},
};
static struct imx_fb_platform_data eukrea_mbimx27_fb_data = {
.mode = eukrea_mbimx27_modes,
.num_modes = ARRAY_SIZE(eukrea_mbimx27_modes),
.pwmr = 0x00A903FF,
.lscr1 = 0x00120300,
.dmacr = 0x00040060,
};
static const struct imxuart_platform_data uart_pdata __initconst = {
.flags = IMXUART_HAVE_RTSCTS,
};
#if defined(CONFIG_TOUCHSCREEN_ADS7846)
|| defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
#define ADS7846_PENDOWN (GPIO_PORTD | 25)
static void ads7846_dev_init(void)
{
if (gpio_request(ADS7846_PENDOWN, "ADS7846 pendown") < 0) {
printk(KERN_ERR "can't get ads746 pen down GPIO\n");
return;
}
gpio_direction_input(ADS7846_PENDOWN);
}
static int ads7846_get_pendown_state(void)
{
return !gpio_get_value(ADS7846_PENDOWN);
}
static struct ads7846_platform_data ads7846_config __initdata = {
.get_pendown_state = ads7846_get_pendown_state,
.keep_vref_on = 1,
};
static struct spi_board_info eukrea_mbimx27_spi_board_info[] __initdata = {
[0] = {
.modalias = "ads7846",
.bus_num = 0,
.chip_select = 0,
.max_speed_hz = 1500000,
.irq = IRQ_GPIOD(25),
.platform_data = &ads7846_config,
.mode = SPI_MODE_2,
},
};
static int eukrea_mbimx27_spi_cs[] = {GPIO_PORTD | 28};
static const struct spi_imx_master eukrea_mbimx27_spi0_data __initconst = {
.chipselect = eukrea_mbimx27_spi_cs,
.num_chipselect = ARRAY_SIZE(eukrea_mbimx27_spi_cs),
};
#endif
static struct platform_device *platform_devices[] __initdata = {
&leds_gpio,
};
/*
* system init for baseboard usage. Will be called by cpuimx27 init.
*
* Add platform devices present on this baseboard and init
* them from CPU side as far as required to use them later on
*/
void __init eukrea_mbimx27_baseboard_init(void)
{
mxc_gpio_setup_multiple_pins(eukrea_mbimx27_pins,
ARRAY_SIZE(eukrea_mbimx27_pins), "MBIMX27");
imx27_add_imx_uart1(&uart_pdata);
imx27_add_imx_uart2(&uart_pdata);
mxc_register_device(&mxc_fb_device, &eukrea_mbimx27_fb_data);
mxc_register_device(&mxc_sdhc_device0, NULL);
#if defined(CONFIG_TOUCHSCREEN_ADS7846)
|| defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
/* SPI and ADS7846 Touchscreen controler init */
mxc_gpio_mode(GPIO_PORTD | 28 | GPIO_GPIO | GPIO_OUT);
mxc_gpio_mode(GPIO_PORTD | 25 | GPIO_GPIO | GPIO_IN);
imx27_add_spi_imx0(&eukrea_mbimx27_spi0_data);
spi_register_board_info(eukrea_mbimx27_spi_board_info,
ARRAY_SIZE(eukrea_mbimx27_spi_board_info));
ads7846_dev_init();
#endif
/* Leds configuration */
mxc_gpio_mode(GPIO_PORTF | 16 | GPIO_GPIO | GPIO_OUT);
mxc_gpio_mode(GPIO_PORTF | 19 | GPIO_GPIO | GPIO_OUT);
/* Backlight */
mxc_gpio_mode(GPIO_PORTE | 5 | GPIO_GPIO | GPIO_OUT);
platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
}