blob: f0052dccf9a86858325bcaa98d9c34d8beec4e37 [file] [log] [blame]
/include/ "skeleton.dtsi"
/ {
compatible = "brcm,bcm2835";
model = "BCM2835";
interrupt-parent = <&intc>;
chosen {
bootargs = "earlyprintk console=ttyAMA0";
};
soc {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x7e000000 0x20000000 0x02000000>;
timer {
compatible = "brcm,bcm2835-system-timer";
reg = <0x7e003000 0x1000>;
interrupts = <1 0>, <1 1>, <1 2>, <1 3>;
clock-frequency = <1000000>;
};
intc: interrupt-controller {
compatible = "brcm,bcm2835-armctrl-ic";
reg = <0x7e00b200 0x200>;
interrupt-controller;
#interrupt-cells = <2>;
};
watchdog {
compatible = "brcm,bcm2835-pm-wdt";
reg = <0x7e100000 0x28>;
};
rng {
compatible = "brcm,bcm2835-rng";
reg = <0x7e104000 0x10>;
};
uart@20201000 {
compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell";
reg = <0x7e201000 0x1000>;
interrupts = <2 25>;
clock-frequency = <3000000>;
};
gpio: gpio {
compatible = "brcm,bcm2835-gpio";
reg = <0x7e200000 0xb4>;
/*
* The GPIO IP block is designed for 3 banks of GPIOs.
* Each bank has a GPIO interrupt for itself.
* There is an overall "any bank" interrupt.
* In order, these are GIC interrupts 17, 18, 19, 20.
* Since the BCM2835 only has 2 banks, the 2nd bank
* interrupt output appears to be mirrored onto the
* 3rd bank's interrupt signal.
* So, a bank0 interrupt shows up on 17, 20, and
* a bank1 interrupt shows up on 18, 19, 20!
*/
interrupts = <2 17>, <2 18>, <2 19>, <2 20>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
spi: spi@20204000 {
compatible = "brcm,bcm2835-spi";
reg = <0x7e204000 0x1000>;
interrupts = <2 22>;
clocks = <&clk_spi>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c0: i2c@20205000 {
compatible = "brcm,bcm2835-i2c";
reg = <0x7e205000 0x1000>;
interrupts = <2 21>;
clocks = <&clk_i2c>;
status = "disabled";
};
i2c1: i2c@20804000 {
compatible = "brcm,bcm2835-i2c";
reg = <0x7e804000 0x1000>;
interrupts = <2 21>;
clocks = <&clk_i2c>;
status = "disabled";
};
sdhci: sdhci {
compatible = "brcm,bcm2835-sdhci";
reg = <0x7e300000 0x100>;
interrupts = <2 30>;
clocks = <&clk_mmc>;
status = "disabled";
};
};
clocks {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <0>;
clk_mmc: mmc {
compatible = "fixed-clock";
reg = <0>;
#clock-cells = <0>;
clock-frequency = <100000000>;
};
clk_i2c: i2c {
compatible = "fixed-clock";
reg = <1>;
#clock-cells = <0>;
clock-frequency = <250000000>;
};
clk_spi: spi {
compatible = "fixed-clock";
reg = <2>;
#clock-cells = <0>;
clock-frequency = <250000000>;
};
};
};