| /dts-v1/; |
| |
| #include "kirkwood.dtsi" |
| #include "kirkwood-6281.dtsi" |
| |
| / { |
| model = "Seagate FreeAgent Dockstar"; |
| compatible = "seagate,dockstar", "marvell,kirkwood-88f6281", "marvell,kirkwood"; |
| |
| memory { |
| device_type = "memory"; |
| reg = <0x00000000 0x8000000>; |
| }; |
| |
| chosen { |
| bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10"; |
| }; |
| |
| ocp@f1000000 { |
| pinctrl: pinctrl@10000 { |
| pmx_usb_power_enable: pmx-usb-power-enable { |
| marvell,pins = "mpp29"; |
| marvell,function = "gpio"; |
| }; |
| pmx_led_green: pmx-led-green { |
| marvell,pins = "mpp46"; |
| marvell,function = "gpio"; |
| }; |
| pmx_led_orange: pmx-led-orange { |
| marvell,pins = "mpp47"; |
| marvell,function = "gpio"; |
| }; |
| }; |
| serial@12000 { |
| status = "ok"; |
| }; |
| }; |
| gpio-leds { |
| compatible = "gpio-leds"; |
| pinctrl-0 = <&pmx_led_green &pmx_led_orange>; |
| pinctrl-names = "default"; |
| |
| health { |
| label = "status:green:health"; |
| gpios = <&gpio1 14 1>; |
| linux,default-trigger = "default-on"; |
| }; |
| fault { |
| label = "status:orange:fault"; |
| gpios = <&gpio1 15 1>; |
| }; |
| }; |
| regulators { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| pinctrl-0 = <&pmx_usb_power_enable>; |
| pinctrl-names = "default"; |
| |
| usb_power: regulator@1 { |
| compatible = "regulator-fixed"; |
| reg = <1>; |
| regulator-name = "USB Power"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| enable-active-high; |
| regulator-always-on; |
| regulator-boot-on; |
| gpio = <&gpio0 29 0>; |
| }; |
| }; |
| }; |
| |
| &nand { |
| status = "okay"; |
| |
| partition@0 { |
| label = "u-boot"; |
| reg = <0x0000000 0x100000>; |
| read-only; |
| }; |
| |
| partition@100000 { |
| label = "uImage"; |
| reg = <0x0100000 0x400000>; |
| }; |
| |
| partition@500000 { |
| label = "data"; |
| reg = <0x0500000 0xfb00000>; |
| }; |
| }; |
| |
| &mdio { |
| status = "okay"; |
| |
| ethphy0: ethernet-phy@0 { |
| device_type = "ethernet-phy"; |
| compatible = "marvell,88e1116"; |
| reg = <0>; |
| }; |
| }; |
| |
| ð0 { |
| status = "okay"; |
| ethernet0-port@0 { |
| phy-handle = <ðphy0>; |
| }; |
| }; |