blob: f6237a0b1133c0429cc27a2a0c26282bd6051b8c [file] [log] [blame]
/* Copyright 2003 Tungsten Graphics, Inc., Cedar Park, Texas.
* All Rights Reserved.
*
* Permission is hereby granted, free of charge, to any person obtaining a
* copy of this software and associated documentation files (the
* "Software"), to deal in the Software without restriction, including
* without limitation the rights to use, copy, modify, merge, publish,
* distribute, sub license, and/or sell copies of the Software, and to
* permit persons to whom the Software is furnished to do so, subject to
* the following conditions:
*
* The above copyright notice and this permission notice (including the
* next paragraph) shall be included in all copies or substantial portions
* of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS
* OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
* IN NO EVENT SHALL TUNGSTEN GRAPHICS AND/OR ITS SUPPLIERS BE LIABLE FOR
* ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT,
* TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE
* SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
*/
#ifndef _I915_REG_H_
#define _I915_REG_H_
/*
* The Bridge device's PCI config space has information about the
* fb aperture size and the amount of pre-reserved memory.
*/
#define INTEL_GMCH_CTRL 0x52
#define INTEL_GMCH_ENABLED 0x4
#define INTEL_GMCH_MEM_MASK 0x1
#define INTEL_GMCH_MEM_64M 0x1
#define INTEL_GMCH_MEM_128M 0
#define INTEL_GMCH_GMS_MASK (0xf << 4)
#define INTEL_855_GMCH_GMS_DISABLED (0x0 << 4)
#define INTEL_855_GMCH_GMS_STOLEN_1M (0x1 << 4)
#define INTEL_855_GMCH_GMS_STOLEN_4M (0x2 << 4)
#define INTEL_855_GMCH_GMS_STOLEN_8M (0x3 << 4)
#define INTEL_855_GMCH_GMS_STOLEN_16M (0x4 << 4)
#define INTEL_855_GMCH_GMS_STOLEN_32M (0x5 << 4)
#define INTEL_915G_GMCH_GMS_STOLEN_48M (0x6 << 4)
#define INTEL_915G_GMCH_GMS_STOLEN_64M (0x7 << 4)
#define INTEL_GMCH_GMS_STOLEN_128M (0x8 << 4)
#define INTEL_GMCH_GMS_STOLEN_256M (0x9 << 4)
#define INTEL_GMCH_GMS_STOLEN_96M (0xa << 4)
#define INTEL_GMCH_GMS_STOLEN_160M (0xb << 4)
#define INTEL_GMCH_GMS_STOLEN_224M (0xc << 4)
#define INTEL_GMCH_GMS_STOLEN_352M (0xd << 4)
/* PCI config space */
#define HPLLCC 0xc0 /* 855 only */
#define GC_CLOCK_CONTROL_MASK (3 << 0)
#define GC_CLOCK_133_200 (0 << 0)
#define GC_CLOCK_100_200 (1 << 0)
#define GC_CLOCK_100_133 (2 << 0)
#define GC_CLOCK_166_250 (3 << 0)
#define GCFGC 0xf0 /* 915+ only */
#define GC_LOW_FREQUENCY_ENABLE (1 << 7)
#define GC_DISPLAY_CLOCK_190_200_MHZ (0 << 4)
#define GC_DISPLAY_CLOCK_333_MHZ (4 << 4)
#define GC_DISPLAY_CLOCK_MASK (7 << 4)
#define LBB 0xf4
/* VGA stuff */
#define VGA_ST01_MDA 0x3ba
#define VGA_ST01_CGA 0x3da
#define VGA_MSR_WRITE 0x3c2
#define VGA_MSR_READ 0x3cc
#define VGA_MSR_MEM_EN (1<<1)
#define VGA_MSR_CGA_MODE (1<<0)
#define VGA_SR_INDEX 0x3c4
#define VGA_SR_DATA 0x3c5
#define VGA_AR_INDEX 0x3c0
#define VGA_AR_VID_EN (1<<5)
#define VGA_AR_DATA_WRITE 0x3c0
#define VGA_AR_DATA_READ 0x3c1
#define VGA_GR_INDEX 0x3ce
#define VGA_GR_DATA 0x3cf
/* GR05 */
#define VGA_GR_MEM_READ_MODE_SHIFT 3
#define VGA_GR_MEM_READ_MODE_PLANE 1
/* GR06 */
#define VGA_GR_MEM_MODE_MASK 0xc
#define VGA_GR_MEM_MODE_SHIFT 2
#define VGA_GR_MEM_A0000_AFFFF 0
#define VGA_GR_MEM_A0000_BFFFF 1
#define VGA_GR_MEM_B0000_B7FFF 2
#define VGA_GR_MEM_B0000_BFFFF 3
#define VGA_DACMASK 0x3c6
#define VGA_DACRX 0x3c7
#define VGA_DACWX 0x3c8
#define VGA_DACDATA 0x3c9
#define VGA_CR_INDEX_MDA 0x3b4
#define VGA_CR_DATA_MDA 0x3b5
#define VGA_CR_INDEX_CGA 0x3d4
#define VGA_CR_DATA_CGA 0x3d5
/*
* Memory interface instructions used by the kernel
*/
#define MI_INSTR(opcode, flags) (((opcode) << 23) | (flags))
#define MI_NOOP MI_INSTR(0, 0)
#define MI_USER_INTERRUPT MI_INSTR(0x02, 0)
#define MI_WAIT_FOR_EVENT MI_INSTR(0x03, 0)
#define MI_WAIT_FOR_PLANE_B_FLIP (1<<6)
#define MI_WAIT_FOR_PLANE_A_FLIP (1<<2)
#define MI_WAIT_FOR_PLANE_A_SCANLINES (1<<1)
#define MI_FLUSH MI_INSTR(0x04, 0)
#define MI_READ_FLUSH (1 << 0)
#define MI_EXE_FLUSH (1 << 1)
#define MI_NO_WRITE_FLUSH (1 << 2)
#define MI_SCENE_COUNT (1 << 3) /* just increment scene count */
#define MI_END_SCENE (1 << 4) /* flush binner and incr scene count */
#define MI_BATCH_BUFFER_END MI_INSTR(0x0a, 0)
#define MI_REPORT_HEAD MI_INSTR(0x07, 0)
#define MI_LOAD_SCAN_LINES_INCL MI_INSTR(0x12, 0)
#define MI_STORE_DWORD_IMM MI_INSTR(0x20, 1)
#define MI_MEM_VIRTUAL (1 << 22) /* 965+ only */
#define MI_STORE_DWORD_INDEX MI_INSTR(0x21, 1)
#define MI_STORE_DWORD_INDEX_SHIFT 2
#define MI_LOAD_REGISTER_IMM MI_INSTR(0x22, 1)
#define MI_BATCH_BUFFER MI_INSTR(0x30, 1)
#define MI_BATCH_NON_SECURE (1)
#define MI_BATCH_NON_SECURE_I965 (1<<8)
#define MI_BATCH_BUFFER_START MI_INSTR(0x31, 0)
/*
* 3D instructions used by the kernel
*/
#define GFX_INSTR(opcode, flags) ((0x3 << 29) | ((opcode) << 24) | (flags))
#define GFX_OP_RASTER_RULES ((0x3<<29)|(0x7<<24))
#define GFX_OP_SCISSOR ((0x3<<29)|(0x1c<<24)|(0x10<<19))
#define SC_UPDATE_SCISSOR (0x1<<1)
#define SC_ENABLE_MASK (0x1<<0)
#define SC_ENABLE (0x1<<0)
#define GFX_OP_LOAD_INDIRECT ((0x3<<29)|(0x1d<<24)|(0x7<<16))
#define GFX_OP_SCISSOR_INFO ((0x3<<29)|(0x1d<<24)|(0x81<<16)|(0x1))
#define SCI_YMIN_MASK (0xffff<<16)
#define SCI_XMIN_MASK (0xffff<<0)
#define SCI_YMAX_MASK (0xffff<<16)
#define SCI_XMAX_MASK (0xffff<<0)
#define GFX_OP_SCISSOR_ENABLE ((0x3<<29)|(0x1c<<24)|(0x10<<19))
#define GFX_OP_SCISSOR_RECT ((0x3<<29)|(0x1d<<24)|(0x81<<16)|1)
#define GFX_OP_COLOR_FACTOR ((0x3<<29)|(0x1d<<24)|(0x1<<16)|0x0)
#define GFX_OP_STIPPLE ((0x3<<29)|(0x1d<<24)|(0x83<<16))
#define GFX_OP_MAP_INFO ((0x3<<29)|(0x1d<<24)|0x4)
#define GFX_OP_DESTBUFFER_VARS ((0x3<<29)|(0x1d<<24)|(0x85<<16)|0x0)
#define GFX_OP_DESTBUFFER_INFO ((0x3<<29)|(0x1d<<24)|(0x8e<<16)|1)
#define GFX_OP_DRAWRECT_INFO ((0x3<<29)|(0x1d<<24)|(0x80<<16)|(0x3))
#define GFX_OP_DRAWRECT_INFO_I965 ((0x7900<<16)|0x2)
#define SRC_COPY_BLT_CMD ((2<<29)|(0x43<<22)|4)
#define XY_SRC_COPY_BLT_CMD ((2<<29)|(0x53<<22)|6)
#define XY_MONO_SRC_COPY_IMM_BLT ((2<<29)|(0x71<<22)|5)
#define XY_SRC_COPY_BLT_WRITE_ALPHA (1<<21)
#define XY_SRC_COPY_BLT_WRITE_RGB (1<<20)
#define BLT_DEPTH_8 (0<<24)
#define BLT_DEPTH_16_565 (1<<24)
#define BLT_DEPTH_16_1555 (2<<24)
#define BLT_DEPTH_32 (3<<24)
#define BLT_ROP_GXCOPY (0xcc<<16)
#define XY_SRC_COPY_BLT_SRC_TILED (1<<15) /* 965+ only */
#define XY_SRC_COPY_BLT_DST_TILED (1<<11) /* 965+ only */
#define CMD_OP_DISPLAYBUFFER_INFO ((0x0<<29)|(0x14<<23)|2)
#define ASYNC_FLIP (1<<22)
#define DISPLAY_PLANE_A (0<<20)
#define DISPLAY_PLANE_B (1<<20)
/*
* Fence registers
*/
#define FENCE_REG_830_0 0x2000
#define FENCE_REG_945_8 0x3000
#define I830_FENCE_START_MASK 0x07f80000
#define I830_FENCE_TILING_Y_SHIFT 12
#define I830_FENCE_SIZE_BITS(size) ((ffs((size) >> 19) - 1) << 8)
#define I830_FENCE_PITCH_SHIFT 4
#define I830_FENCE_REG_VALID (1<<0)
#define I915_FENCE_MAX_PITCH_VAL 0x10
#define I830_FENCE_MAX_PITCH_VAL 6
#define I830_FENCE_MAX_SIZE_VAL (1<<8)
#define I915_FENCE_START_MASK 0x0ff00000
#define I915_FENCE_SIZE_BITS(size) ((ffs((size) >> 20) - 1) << 8)
#define FENCE_REG_965_0 0x03000
#define I965_FENCE_PITCH_SHIFT 2
#define I965_FENCE_TILING_Y_SHIFT 1
#define I965_FENCE_REG_VALID (1<<0)
#define I965_FENCE_MAX_PITCH_VAL 0x0400
/*
* Instruction and interrupt control regs
*/
#define PRB0_TAIL 0x02030
#define PRB0_HEAD 0x02034
#define PRB0_START 0x02038
#define PRB0_CTL 0x0203c
#define TAIL_ADDR 0x001FFFF8
#define HEAD_WRAP_COUNT 0xFFE00000
#define HEAD_WRAP_ONE 0x00200000
#define HEAD_ADDR 0x001FFFFC
#define RING_NR_PAGES 0x001FF000
#define RING_REPORT_MASK 0x00000006
#define RING_REPORT_64K 0x00000002
#define RING_REPORT_128K 0x00000004
#define RING_NO_REPORT 0x00000000
#define RING_VALID_MASK 0x00000001
#define RING_VALID 0x00000001
#define RING_INVALID 0x00000000
#define PRB1_TAIL 0x02040 /* 915+ only */
#define PRB1_HEAD 0x02044 /* 915+ only */
#define PRB1_START 0x02048 /* 915+ only */
#define PRB1_CTL 0x0204c /* 915+ only */
#define ACTHD_I965 0x02074
#define HWS_PGA 0x02080
#define HWS_ADDRESS_MASK 0xfffff000
#define HWS_START_ADDRESS_SHIFT 4
#define IPEIR 0x02088
#define NOPID 0x02094
#define HWSTAM 0x02098
#define SCPD0 0x0209c /* 915+ only */
#define IER 0x020a0
#define IIR 0x020a4
#define IMR 0x020a8
#define ISR 0x020ac
#define I915_PIPE_CONTROL_NOTIFY_INTERRUPT (1<<18)
#define I915_DISPLAY_PORT_INTERRUPT (1<<17)
#define I915_RENDER_COMMAND_PARSER_ERROR_INTERRUPT (1<<15)
#define I915_GMCH_THERMAL_SENSOR_EVENT_INTERRUPT (1<<14)
#define I915_HWB_OOM_INTERRUPT (1<<13)
#define I915_SYNC_STATUS_INTERRUPT (1<<12)
#define I915_DISPLAY_PLANE_A_FLIP_PENDING_INTERRUPT (1<<11)
#define I915_DISPLAY_PLANE_B_FLIP_PENDING_INTERRUPT (1<<10)
#define I915_OVERLAY_PLANE_FLIP_PENDING_INTERRUPT (1<<9)
#define I915_DISPLAY_PLANE_C_FLIP_PENDING_INTERRUPT (1<<8)
#define I915_DISPLAY_PIPE_A_VBLANK_INTERRUPT (1<<7)
#define I915_DISPLAY_PIPE_A_EVENT_INTERRUPT (1<<6)
#define I915_DISPLAY_PIPE_B_VBLANK_INTERRUPT (1<<5)
#define I915_DISPLAY_PIPE_B_EVENT_INTERRUPT (1<<4)
#define I915_DEBUG_INTERRUPT (1<<2)
#define I915_USER_INTERRUPT (1<<1)
#define I915_ASLE_INTERRUPT (1<<0)
#define EIR 0x020b0
#define EMR 0x020b4
#define ESR 0x020b8
#define INSTPM 0x020c0
#define ACTHD 0x020c8
#define FW_BLC 0x020d8
#define FW_BLC_SELF 0x020e0 /* 915+ only */
#define MI_ARB_STATE 0x020e4 /* 915+ only */
#define CACHE_MODE_0 0x02120 /* 915+ only */
#define CM0_MASK_SHIFT 16
#define CM0_IZ_OPT_DISABLE (1<<6)
#define CM0_ZR_OPT_DISABLE (1<<5)
#define CM0_DEPTH_EVICT_DISABLE (1<<4)
#define CM0_COLOR_EVICT_DISABLE (1<<3)
#define CM0_DEPTH_WRITE_DISABLE (1<<1)
#define CM0_RC_OP_FLUSH_DISABLE (1<<0)
#define GFX_FLSH_CNTL 0x02170 /* 915+ only */
/*
* Framebuffer compression (915+ only)
*/
#define FBC_CFB_BASE 0x03200 /* 4k page aligned */
#define FBC_LL_BASE 0x03204 /* 4k page aligned */
#define FBC_CONTROL 0x03208
#define FBC_CTL_EN (1<<31)
#define FBC_CTL_PERIODIC (1<<30)
#define FBC_CTL_INTERVAL_SHIFT (16)
#define FBC_CTL_UNCOMPRESSIBLE (1<<14)
#define FBC_CTL_STRIDE_SHIFT (5)
#define FBC_CTL_FENCENO (1<<0)
#define FBC_COMMAND 0x0320c
#define FBC_CMD_COMPRESS (1<<0)
#define FBC_STATUS 0x03210
#define FBC_STAT_COMPRESSING (1<<31)
#define FBC_STAT_COMPRESSED (1<<30)
#define FBC_STAT_MODIFIED (1<<29)
#define FBC_STAT_CURRENT_LINE (1<<0)
#define FBC_CONTROL2 0x03214
#define FBC_CTL_FENCE_DBL (0<<4)
#define FBC_CTL_IDLE_IMM (0<<2)
#define FBC_CTL_IDLE_FULL (1<<2)
#define FBC_CTL_IDLE_LINE (2<<2)
#define FBC_CTL_IDLE_DEBUG (3<<2)
#define FBC_CTL_CPU_FENCE (1<<1)
#define FBC_CTL_PLANEA (0<<0)
#define FBC_CTL_PLANEB (1<<0)
#define FBC_FENCE_OFF 0x0321b
#define FBC_LL_SIZE (1536)
/*
* GPIO regs
*/
#define GPIOA 0x5010
#define GPIOB 0x5014
#define GPIOC 0x5018
#define GPIOD 0x501c
#define GPIOE 0x5020
#define GPIOF 0x5024
#define GPIOG 0x5028
#define GPIOH 0x502c
# define GPIO_CLOCK_DIR_MASK (1 << 0)
# define GPIO_CLOCK_DIR_IN (0 << 1)
# define GPIO_CLOCK_DIR_OUT (1 << 1)
# define GPIO_CLOCK_VAL_MASK (1 << 2)
# define GPIO_CLOCK_VAL_OUT (1 << 3)
# define GPIO_CLOCK_VAL_IN (1 << 4)
# define GPIO_CLOCK_PULLUP_DISABLE (1 << 5)
# define GPIO_DATA_DIR_MASK (1 << 8)
# define GPIO_DATA_DIR_IN (0 << 9)
# define GPIO_DATA_DIR_OUT (1 << 9)
# define GPIO_DATA_VAL_MASK (1 << 10)
# define GPIO_DATA_VAL_OUT (1 << 11)
# define GPIO_DATA_VAL_IN (1 << 12)
# define GPIO_DATA_PULLUP_DISABLE (1 << 13)
/*
* Clock control & power management
*/
#define VGA0 0x6000
#define VGA1 0x6004
#define VGA_PD 0x6010
#define VGA0_PD_P2_DIV_4 (1 << 7)
#define VGA0_PD_P1_DIV_2 (1 << 5)
#define VGA0_PD_P1_SHIFT 0
#define VGA0_PD_P1_MASK (0x1f << 0)
#define VGA1_PD_P2_DIV_4 (1 << 15)
#define VGA1_PD_P1_DIV_2 (1 << 13)
#define VGA1_PD_P1_SHIFT 8
#define VGA1_PD_P1_MASK (0x1f << 8)
#define DPLL_A 0x06014
#define DPLL_B 0x06018
#define DPLL_VCO_ENABLE (1 << 31)
#define DPLL_DVO_HIGH_SPEED (1 << 30)
#define DPLL_SYNCLOCK_ENABLE (1 << 29)
#define DPLL_VGA_MODE_DIS (1 << 28)
#define DPLLB_MODE_DAC_SERIAL (1 << 26) /* i915 */
#define DPLLB_MODE_LVDS (2 << 26) /* i915 */
#define DPLL_MODE_MASK (3 << 26)
#define DPLL_DAC_SERIAL_P2_CLOCK_DIV_10 (0 << 24) /* i915 */
#define DPLL_DAC_SERIAL_P2_CLOCK_DIV_5 (1 << 24) /* i915 */
#define DPLLB_LVDS_P2_CLOCK_DIV_14 (0 << 24) /* i915 */
#define DPLLB_LVDS_P2_CLOCK_DIV_7 (1 << 24) /* i915 */
#define DPLL_P2_CLOCK_DIV_MASK 0x03000000 /* i915 */
#define DPLL_FPA01_P1_POST_DIV_MASK 0x00ff0000 /* i915 */
#define DPLL_FPA01_P1_POST_DIV_MASK_IGD 0x00ff8000 /* IGD */
#define I915_FIFO_UNDERRUN_STATUS (1UL<<31)
#define I915_CRC_ERROR_ENABLE (1UL<<29)
#define I915_CRC_DONE_ENABLE (1UL<<28)
#define I915_GMBUS_EVENT_ENABLE (1UL<<27)
#define I915_VSYNC_INTERRUPT_ENABLE (1UL<<25)
#define I915_DISPLAY_LINE_COMPARE_ENABLE (1UL<<24)
#define I915_DPST_EVENT_ENABLE (1UL<<23)
#define I915_LEGACY_BLC_EVENT_ENABLE (1UL<<22)
#define I915_ODD_FIELD_INTERRUPT_ENABLE (1UL<<21)
#define I915_EVEN_FIELD_INTERRUPT_ENABLE (1UL<<20)
#define I915_START_VBLANK_INTERRUPT_ENABLE (1UL<<18) /* 965 or later */
#define I915_VBLANK_INTERRUPT_ENABLE (1UL<<17)
#define I915_OVERLAY_UPDATED_ENABLE (1UL<<16)
#define I915_CRC_ERROR_INTERRUPT_STATUS (1UL<<13)
#define I915_CRC_DONE_INTERRUPT_STATUS (1UL<<12)
#define I915_GMBUS_INTERRUPT_STATUS (1UL<<11)
#define I915_VSYNC_INTERRUPT_STATUS (1UL<<9)
#define I915_DISPLAY_LINE_COMPARE_STATUS (1UL<<8)
#define I915_DPST_EVENT_STATUS (1UL<<7)
#define I915_LEGACY_BLC_EVENT_STATUS (1UL<<6)
#define I915_ODD_FIELD_INTERRUPT_STATUS (1UL<<5)
#define I915_EVEN_FIELD_INTERRUPT_STATUS (1UL<<4)
#define I915_START_VBLANK_INTERRUPT_STATUS (1UL<<2) /* 965 or later */
#define I915_VBLANK_INTERRUPT_STATUS (1UL<<1)
#define I915_OVERLAY_UPDATED_STATUS (1UL<<0)
#define SRX_INDEX 0x3c4
#define SRX_DATA 0x3c5
#define SR01 1
#define SR01_SCREEN_OFF (1<<5)
#define PPCR 0x61204
#define PPCR_ON (1<<0)
#define DVOB 0x61140
#define DVOB_ON (1<<31)
#define DVOC 0x61160
#define DVOC_ON (1<<31)
#define LVDS 0x61180
#define LVDS_ON (1<<31)
#define ADPA 0x61100
#define ADPA_DPMS_MASK (~(3<<10))
#define ADPA_DPMS_ON (0<<10)
#define ADPA_DPMS_SUSPEND (1<<10)
#define ADPA_DPMS_STANDBY (2<<10)
#define ADPA_DPMS_OFF (3<<10)
#define RING_TAIL 0x00
#define TAIL_ADDR 0x001FFFF8
#define RING_HEAD 0x04
#define HEAD_WRAP_COUNT 0xFFE00000
#define HEAD_WRAP_ONE 0x00200000
#define HEAD_ADDR 0x001FFFFC
#define RING_START 0x08
#define START_ADDR 0xFFFFF000
#define RING_LEN 0x0C
#define RING_NR_PAGES 0x001FF000
#define RING_REPORT_MASK 0x00000006
#define RING_REPORT_64K 0x00000002
#define RING_REPORT_128K 0x00000004
#define RING_NO_REPORT 0x00000000
#define RING_VALID_MASK 0x00000001
#define RING_VALID 0x00000001
#define RING_INVALID 0x00000000
/* Scratch pad debug 0 reg:
*/
#define DPLL_FPA01_P1_POST_DIV_MASK_I830 0x001f0000
/*
* The i830 generation, in LVDS mode, defines P1 as the bit number set within
* this field (only one bit may be set).
*/
#define DPLL_FPA01_P1_POST_DIV_MASK_I830_LVDS 0x003f0000
#define DPLL_FPA01_P1_POST_DIV_SHIFT 16
#define DPLL_FPA01_P1_POST_DIV_SHIFT_IGD 15
/* i830, required in DVO non-gang */
#define PLL_P2_DIVIDE_BY_4 (1 << 23)
#define PLL_P1_DIVIDE_BY_TWO (1 << 21) /* i830 */
#define PLL_REF_INPUT_DREFCLK (0 << 13)
#define PLL_REF_INPUT_TVCLKINA (1 << 13) /* i830 */
#define PLL_REF_INPUT_TVCLKINBC (2 << 13) /* SDVO TVCLKIN */
#define PLLB_REF_INPUT_SPREADSPECTRUMIN (3 << 13)
#define PLL_REF_INPUT_MASK (3 << 13)
#define PLL_LOAD_PULSE_PHASE_SHIFT 9
/* IGDNG */
# define PLL_REF_SDVO_HDMI_MULTIPLIER_SHIFT 9
# define PLL_REF_SDVO_HDMI_MULTIPLIER_MASK (7 << 9)
# define PLL_REF_SDVO_HDMI_MULTIPLIER(x) (((x)-1) << 9)
# define DPLL_FPA1_P1_POST_DIV_SHIFT 0
# define DPLL_FPA1_P1_POST_DIV_MASK 0xff
/*
* Parallel to Serial Load Pulse phase selection.
* Selects the phase for the 10X DPLL clock for the PCIe
* digital display port. The range is 4 to 13; 10 or more
* is just a flip delay. The default is 6
*/
#define PLL_LOAD_PULSE_PHASE_MASK (0xf << PLL_LOAD_PULSE_PHASE_SHIFT)
#define DISPLAY_RATE_SELECT_FPA1 (1 << 8)
/*
* SDVO multiplier for 945G/GM. Not used on 965.
*/
#define SDVO_MULTIPLIER_MASK 0x000000ff
#define SDVO_MULTIPLIER_SHIFT_HIRES 4
#define SDVO_MULTIPLIER_SHIFT_VGA 0
#define DPLL_A_MD 0x0601c /* 965+ only */
/*
* UDI pixel divider, controlling how many pixels are stuffed into a packet.
*
* Value is pixels minus 1. Must be set to 1 pixel for SDVO.
*/
#define DPLL_MD_UDI_DIVIDER_MASK 0x3f000000
#define DPLL_MD_UDI_DIVIDER_SHIFT 24
/* UDI pixel divider for VGA, same as DPLL_MD_UDI_DIVIDER_MASK. */
#define DPLL_MD_VGA_UDI_DIVIDER_MASK 0x003f0000
#define DPLL_MD_VGA_UDI_DIVIDER_SHIFT 16
/*
* SDVO/UDI pixel multiplier.
*
* SDVO requires that the bus clock rate be between 1 and 2 Ghz, and the bus
* clock rate is 10 times the DPLL clock. At low resolution/refresh rate
* modes, the bus rate would be below the limits, so SDVO allows for stuffing
* dummy bytes in the datastream at an increased clock rate, with both sides of
* the link knowing how many bytes are fill.
*
* So, for a mode with a dotclock of 65Mhz, we would want to double the clock
* rate to 130Mhz to get a bus rate of 1.30Ghz. The DPLL clock rate would be
* set to 130Mhz, and the SDVO multiplier set to 2x in this register and
* through an SDVO command.
*
* This register field has values of multiplication factor minus 1, with
* a maximum multiplier of 5 for SDVO.
*/
#define DPLL_MD_UDI_MULTIPLIER_MASK 0x00003f00
#define DPLL_MD_UDI_MULTIPLIER_SHIFT 8
/*
* SDVO/UDI pixel multiplier for VGA, same as DPLL_MD_UDI_MULTIPLIER_MASK.
* This best be set to the default value (3) or the CRT won't work. No,
* I don't entirely understand what this does...
*/
#define DPLL_MD_VGA_UDI_MULTIPLIER_MASK 0x0000003f
#define DPLL_MD_VGA_UDI_MULTIPLIER_SHIFT 0
#define DPLL_B_MD 0x06020 /* 965+ only */
#define FPA0 0x06040
#define FPA1 0x06044
#define FPB0 0x06048
#define FPB1 0x0604c
#define FP_N_DIV_MASK 0x003f0000
#define FP_N_IGD_DIV_MASK 0x00ff0000
#define FP_N_DIV_SHIFT 16
#define FP_M1_DIV_MASK 0x00003f00
#define FP_M1_DIV_SHIFT 8
#define FP_M2_DIV_MASK 0x0000003f
#define FP_M2_IGD_DIV_MASK 0x000000ff
#define FP_M2_DIV_SHIFT 0
#define DPLL_TEST 0x606c
#define DPLLB_TEST_SDVO_DIV_1 (0 << 22)
#define DPLLB_TEST_SDVO_DIV_2 (1 << 22)
#define DPLLB_TEST_SDVO_DIV_4 (2 << 22)
#define DPLLB_TEST_SDVO_DIV_MASK (3 << 22)
#define DPLLB_TEST_N_BYPASS (1 << 19)
#define DPLLB_TEST_M_BYPASS (1 << 18)
#define DPLLB_INPUT_BUFFER_ENABLE (1 << 16)
#define DPLLA_TEST_N_BYPASS (1 << 3)
#define DPLLA_TEST_M_BYPASS (1 << 2)
#define DPLLA_INPUT_BUFFER_ENABLE (1 << 0)
#define D_STATE 0x6104
#define CG_2D_DIS 0x6200
#define DPCUNIT_CLOCK_GATE_DISABLE (1 << 24)
#define CG_3D_DIS 0x6204
/*
* Palette regs
*/
#define PALETTE_A 0x0a000
#define PALETTE_B 0x0a800
/* MCH MMIO space */
/*
* MCHBAR mirror.
*
* This mirrors the MCHBAR MMIO space whose location is determined by
* device 0 function 0's pci config register 0x44 or 0x48 and matches it in
* every way. It is not accessible from the CP register read instructions.
*
*/
#define MCHBAR_MIRROR_BASE 0x10000
/** 915-945 and GM965 MCH register controlling DRAM channel access */
#define DCC 0x10200
#define DCC_ADDRESSING_MODE_SINGLE_CHANNEL (0 << 0)
#define DCC_ADDRESSING_MODE_DUAL_CHANNEL_ASYMMETRIC (1 << 0)
#define DCC_ADDRESSING_MODE_DUAL_CHANNEL_INTERLEAVED (2 << 0)
#define DCC_ADDRESSING_MODE_MASK (3 << 0)
#define DCC_CHANNEL_XOR_DISABLE (1 << 10)
#define DCC_CHANNEL_XOR_BIT_17 (1 << 9)
/** 965 MCH register controlling DRAM channel configuration */
#define C0DRB3 0x10206
#define C1DRB3 0x10606
/** GM965 GM45 render standby register */
#define MCHBAR_RENDER_STANDBY 0x111B8
#define PEG_BAND_GAP_DATA 0x14d68
/*
* Overlay regs
*/
#define OVADD 0x30000
#define DOVSTA 0x30008
#define OC_BUF (0x3<<20)
#define OGAMC5 0x30010
#define OGAMC4 0x30014
#define OGAMC3 0x30018
#define OGAMC2 0x3001c
#define OGAMC1 0x30020
#define OGAMC0 0x30024
/*
* Display engine regs
*/
/* Pipe A timing regs */
#define HTOTAL_A 0x60000
#define HBLANK_A 0x60004
#define HSYNC_A 0x60008
#define VTOTAL_A 0x6000c
#define VBLANK_A 0x60010
#define VSYNC_A 0x60014
#define PIPEASRC 0x6001c
#define BCLRPAT_A 0x60020
/* Pipe B timing regs */
#define HTOTAL_B 0x61000
#define HBLANK_B 0x61004
#define HSYNC_B 0x61008
#define VTOTAL_B 0x6100c
#define VBLANK_B 0x61010
#define VSYNC_B 0x61014
#define PIPEBSRC 0x6101c
#define BCLRPAT_B 0x61020
/* VGA port control */
#define ADPA 0x61100
#define ADPA_DAC_ENABLE (1<<31)
#define ADPA_DAC_DISABLE 0
#define ADPA_PIPE_SELECT_MASK (1<<30)
#define ADPA_PIPE_A_SELECT 0
#define ADPA_PIPE_B_SELECT (1<<30)
#define ADPA_USE_VGA_HVPOLARITY (1<<15)
#define ADPA_SETS_HVPOLARITY 0
#define ADPA_VSYNC_CNTL_DISABLE (1<<11)
#define ADPA_VSYNC_CNTL_ENABLE 0
#define ADPA_HSYNC_CNTL_DISABLE (1<<10)
#define ADPA_HSYNC_CNTL_ENABLE 0
#define ADPA_VSYNC_ACTIVE_HIGH (1<<4)
#define ADPA_VSYNC_ACTIVE_LOW 0
#define ADPA_HSYNC_ACTIVE_HIGH (1<<3)
#define ADPA_HSYNC_ACTIVE_LOW 0
#define ADPA_DPMS_MASK (~(3<<10))
#define ADPA_DPMS_ON (0<<10)
#define ADPA_DPMS_SUSPEND (1<<10)
#define ADPA_DPMS_STANDBY (2<<10)
#define ADPA_DPMS_OFF (3<<10)
/* Hotplug control (945+ only) */
#define PORT_HOTPLUG_EN 0x61110
#define HDMIB_HOTPLUG_INT_EN (1 << 29)
#define DPB_HOTPLUG_INT_EN (1 << 29)
#define HDMIC_HOTPLUG_INT_EN (1 << 28)
#define DPC_HOTPLUG_INT_EN (1 << 28)
#define HDMID_HOTPLUG_INT_EN (1 << 27)
#define DPD_HOTPLUG_INT_EN (1 << 27)
#define SDVOB_HOTPLUG_INT_EN (1 << 26)
#define SDVOC_HOTPLUG_INT_EN (1 << 25)
#define TV_HOTPLUG_INT_EN (1 << 18)
#define CRT_HOTPLUG_INT_EN (1 << 9)
#define CRT_HOTPLUG_FORCE_DETECT (1 << 3)
#define CRT_HOTPLUG_ACTIVATION_PERIOD_32 (0 << 8)
/* must use period 64 on GM45 according to docs */
#define CRT_HOTPLUG_ACTIVATION_PERIOD_64 (1 << 8)
#define CRT_HOTPLUG_DAC_ON_TIME_2M (0 << 7)
#define CRT_HOTPLUG_DAC_ON_TIME_4M (1 << 7)
#define CRT_HOTPLUG_VOLTAGE_COMPARE_40 (0 << 5)
#define CRT_HOTPLUG_VOLTAGE_COMPARE_50 (1 << 5)
#define CRT_HOTPLUG_VOLTAGE_COMPARE_60 (2 << 5)
#define CRT_HOTPLUG_VOLTAGE_COMPARE_70 (3 << 5)
#define CRT_HOTPLUG_VOLTAGE_COMPARE_MASK (3 << 5)
#define CRT_HOTPLUG_DETECT_DELAY_1G (0 << 4)
#define CRT_HOTPLUG_DETECT_DELAY_2G (1 << 4)
#define CRT_HOTPLUG_DETECT_VOLTAGE_325MV (0 << 2)
#define CRT_HOTPLUG_DETECT_VOLTAGE_475MV (1 << 2)
#define CRT_HOTPLUG_MASK (0x3fc) /* Bits 9-2 */
#define CRT_FORCE_HOTPLUG_MASK 0xfffffe1f
#define HOTPLUG_EN_MASK (HDMIB_HOTPLUG_INT_EN | \
HDMIC_HOTPLUG_INT_EN | \
HDMID_HOTPLUG_INT_EN | \
SDVOB_HOTPLUG_INT_EN | \
SDVOC_HOTPLUG_INT_EN | \
TV_HOTPLUG_INT_EN | \
CRT_HOTPLUG_INT_EN)
#define PORT_HOTPLUG_STAT 0x61114
#define HDMIB_HOTPLUG_INT_STATUS (1 << 29)
#define DPB_HOTPLUG_INT_STATUS (1 << 29)
#define HDMIC_HOTPLUG_INT_STATUS (1 << 28)
#define DPC_HOTPLUG_INT_STATUS (1 << 28)
#define HDMID_HOTPLUG_INT_STATUS (1 << 27)
#define DPD_HOTPLUG_INT_STATUS (1 << 27)
#define CRT_HOTPLUG_INT_STATUS (1 << 11)
#define TV_HOTPLUG_INT_STATUS (1 << 10)
#define CRT_HOTPLUG_MONITOR_MASK (3 << 8)
#define CRT_HOTPLUG_MONITOR_COLOR (3 << 8)
#define CRT_HOTPLUG_MONITOR_MONO (2 << 8)
#define CRT_HOTPLUG_MONITOR_NONE (0 << 8)
#define SDVOC_HOTPLUG_INT_STATUS (1 << 7)
#define SDVOB_HOTPLUG_INT_STATUS (1 << 6)
/* SDVO port control */
#define SDVOB 0x61140
#define SDVOC 0x61160
#define SDVO_ENABLE (1 << 31)
#define SDVO_PIPE_B_SELECT (1 << 30)
#define SDVO_STALL_SELECT (1 << 29)
#define SDVO_INTERRUPT_ENABLE (1 << 26)
/**
* 915G/GM SDVO pixel multiplier.
*
* Programmed value is multiplier - 1, up to 5x.
*
* \sa DPLL_MD_UDI_MULTIPLIER_MASK
*/
#define SDVO_PORT_MULTIPLY_MASK (7 << 23)
#define SDVO_PORT_MULTIPLY_SHIFT 23
#define SDVO_PHASE_SELECT_MASK (15 << 19)
#define SDVO_PHASE_SELECT_DEFAULT (6 << 19)
#define SDVO_CLOCK_OUTPUT_INVERT (1 << 18)
#define SDVOC_GANG_MODE (1 << 16)
#define SDVO_ENCODING_SDVO (0x0 << 10)
#define SDVO_ENCODING_HDMI (0x2 << 10)
/** Requird for HDMI operation */
#define SDVO_NULL_PACKETS_DURING_VSYNC (1 << 9)
#define SDVO_BORDER_ENABLE (1 << 7)
#define SDVO_AUDIO_ENABLE (1 << 6)
/** New with 965, default is to be set */
#define SDVO_VSYNC_ACTIVE_HIGH (1 << 4)
/** New with 965, default is to be set */
#define SDVO_HSYNC_ACTIVE_HIGH (1 << 3)
#define SDVOB_PCIE_CONCURRENCY (1 << 3)
#define SDVO_DETECTED (1 << 2)
/* Bits to be preserved when writing */
#define SDVOB_PRESERVE_MASK ((1 << 17) | (1 << 16) | (1 << 14) | (1 << 26))
#define SDVOC_PRESERVE_MASK ((1 << 17) | (1 << 26))
/* DVO port control */
#define DVOA 0x61120
#define DVOB 0x61140
#define DVOC 0x61160
#define DVO_ENABLE (1 << 31)
#define DVO_PIPE_B_SELECT (1 << 30)
#define DVO_PIPE_STALL_UNUSED (0 << 28)
#define DVO_PIPE_STALL (1 << 28)
#define DVO_PIPE_STALL_TV (2 << 28)
#define DVO_PIPE_STALL_MASK (3 << 28)
#define DVO_USE_VGA_SYNC (1 << 15)
#define DVO_DATA_ORDER_I740 (0 << 14)
#define DVO_DATA_ORDER_FP (1 << 14)
#define DVO_VSYNC_DISABLE (1 << 11)
#define DVO_HSYNC_DISABLE (1 << 10)
#define DVO_VSYNC_TRISTATE (1 << 9)
#define DVO_HSYNC_TRISTATE (1 << 8)
#define DVO_BORDER_ENABLE (1 << 7)
#define DVO_DATA_ORDER_GBRG (1 << 6)
#define DVO_DATA_ORDER_RGGB (0 << 6)
#define DVO_DATA_ORDER_GBRG_ERRATA (0 << 6)
#define DVO_DATA_ORDER_RGGB_ERRATA (1 << 6)
#define DVO_VSYNC_ACTIVE_HIGH (1 << 4)
#define DVO_HSYNC_ACTIVE_HIGH (1 << 3)
#define DVO_BLANK_ACTIVE_HIGH (1 << 2)
#define DVO_OUTPUT_CSTATE_PIXELS (1 << 1) /* SDG only */
#define DVO_OUTPUT_SOURCE_SIZE_PIXELS (1 << 0) /* SDG only */
#define DVO_PRESERVE_MASK (0x7<<24)
#define DVOA_SRCDIM 0x61124
#define DVOB_SRCDIM 0x61144
#define DVOC_SRCDIM 0x61164
#define DVO_SRCDIM_HORIZONTAL_SHIFT 12
#define DVO_SRCDIM_VERTICAL_SHIFT 0
/* LVDS port control */
#define LVDS 0x61180
/*
* Enables the LVDS port. This bit must be set before DPLLs are enabled, as
* the DPLL semantics change when the LVDS is assigned to that pipe.
*/
#define LVDS_PORT_EN (1 << 31)
/* Selects pipe B for LVDS data. Must be set on pre-965. */
#define LVDS_PIPEB_SELECT (1 << 30)
/*
* Enables the A0-A2 data pairs and CLKA, containing 18 bits of color data per
* pixel.
*/
#define LVDS_A0A2_CLKA_POWER_MASK (3 << 8)
#define LVDS_A0A2_CLKA_POWER_DOWN (0 << 8)
#define LVDS_A0A2_CLKA_POWER_UP (3 << 8)
/*
* Controls the A3 data pair, which contains the additional LSBs for 24 bit
* mode. Only enabled if LVDS_A0A2_CLKA_POWER_UP also indicates it should be
* on.
*/
#define LVDS_A3_POWER_MASK (3 << 6)
#define LVDS_A3_POWER_DOWN (0 << 6)
#define LVDS_A3_POWER_UP (3 << 6)
/*
* Controls the CLKB pair. This should only be set when LVDS_B0B3_POWER_UP
* is set.
*/
#define LVDS_CLKB_POWER_MASK (3 << 4)
#define LVDS_CLKB_POWER_DOWN (0 << 4)
#define LVDS_CLKB_POWER_UP (3 << 4)
/*
* Controls the B0-B3 data pairs. This must be set to match the DPLL p2
* setting for whether we are in dual-channel mode. The B3 pair will
* additionally only be powered up when LVDS_A3_POWER_UP is set.
*/
#define LVDS_B0B3_POWER_MASK (3 << 2)
#define LVDS_B0B3_POWER_DOWN (0 << 2)
#define LVDS_B0B3_POWER_UP (3 << 2)
/* Panel power sequencing */
#define PP_STATUS 0x61200
#define PP_ON (1 << 31)
/*
* Indicates that all dependencies of the panel are on:
*
* - PLL enabled
* - pipe enabled
* - LVDS/DVOB/DVOC on
*/
#define PP_READY (1 << 30)
#define PP_SEQUENCE_NONE (0 << 28)
#define PP_SEQUENCE_ON (1 << 28)
#define PP_SEQUENCE_OFF (2 << 28)
#define PP_SEQUENCE_MASK 0x30000000
#define PP_CONTROL 0x61204
#define POWER_TARGET_ON (1 << 0)
#define PP_ON_DELAYS 0x61208
#define PP_OFF_DELAYS 0x6120c
#define PP_DIVISOR 0x61210
/* Panel fitting */
#define PFIT_CONTROL 0x61230
#define PFIT_ENABLE (1 << 31)
#define PFIT_PIPE_MASK (3 << 29)
#define PFIT_PIPE_SHIFT 29
#define VERT_INTERP_DISABLE (0 << 10)
#define VERT_INTERP_BILINEAR (1 << 10)
#define VERT_INTERP_MASK (3 << 10)
#define VERT_AUTO_SCALE (1 << 9)
#define HORIZ_INTERP_DISABLE (0 << 6)
#define HORIZ_INTERP_BILINEAR (1 << 6)
#define HORIZ_INTERP_MASK (3 << 6)
#define HORIZ_AUTO_SCALE (1 << 5)
#define PANEL_8TO6_DITHER_ENABLE (1 << 3)
#define PFIT_PGM_RATIOS 0x61234
#define PFIT_VERT_SCALE_MASK 0xfff00000
#define PFIT_HORIZ_SCALE_MASK 0x0000fff0
#define PFIT_AUTO_RATIOS 0x61238
/* Backlight control */
#define BLC_PWM_CTL 0x61254
#define BACKLIGHT_MODULATION_FREQ_SHIFT (17)
#define BLC_PWM_CTL2 0x61250 /* 965+ only */
#define BLM_COMBINATION_MODE (1 << 30)
/*
* This is the most significant 15 bits of the number of backlight cycles in a
* complete cycle of the modulated backlight control.
*
* The actual value is this field multiplied by two.
*/
#define BACKLIGHT_MODULATION_FREQ_MASK (0x7fff << 17)
#define BLM_LEGACY_MODE (1 << 16)
/*
* This is the number of cycles out of the backlight modulation cycle for which
* the backlight is on.
*
* This field must be no greater than the number of cycles in the complete
* backlight modulation cycle.
*/
#define BACKLIGHT_DUTY_CYCLE_SHIFT (0)
#define BACKLIGHT_DUTY_CYCLE_MASK (0xffff)
/* TV port control */
#define TV_CTL 0x68000
/** Enables the TV encoder */
# define TV_ENC_ENABLE (1 << 31)
/** Sources the TV encoder input from pipe B instead of A. */
# define TV_ENC_PIPEB_SELECT (1 << 30)
/** Outputs composite video (DAC A only) */
# define TV_ENC_OUTPUT_COMPOSITE (0 << 28)
/** Outputs SVideo video (DAC B/C) */
# define TV_ENC_OUTPUT_SVIDEO (1 << 28)
/** Outputs Component video (DAC A/B/C) */
# define TV_ENC_OUTPUT_COMPONENT (2 << 28)
/** Outputs Composite and SVideo (DAC A/B/C) */
# define TV_ENC_OUTPUT_SVIDEO_COMPOSITE (3 << 28)
# define TV_TRILEVEL_SYNC (1 << 21)
/** Enables slow sync generation (945GM only) */
# define TV_SLOW_SYNC (1 << 20)
/** Selects 4x oversampling for 480i and 576p */
# define TV_OVERSAMPLE_4X (0 << 18)
/** Selects 2x oversampling for 720p and 1080i */
# define TV_OVERSAMPLE_2X (1 << 18)
/** Selects no oversampling for 1080p */
# define TV_OVERSAMPLE_NONE (2 << 18)
/** Selects 8x oversampling */
# define TV_OVERSAMPLE_8X (3 << 18)
/** Selects progressive mode rather than interlaced */
# define TV_PROGRESSIVE (1 << 17)
/** Sets the colorburst to PAL mode. Required for non-M PAL modes. */
# define TV_PAL_BURST (1 << 16)
/** Field for setting delay of Y compared to C */
# define TV_YC_SKEW_MASK (7 << 12)
/** Enables a fix for 480p/576p standard definition modes on the 915GM only */
# define TV_ENC_SDP_FIX (1 << 11)
/**
* Enables a fix for the 915GM only.
*
* Not sure what it does.
*/
# define TV_ENC_C0_FIX (1 << 10)
/** Bits that must be preserved by software */
# define TV_CTL_SAVE ((1 << 11) | (3 << 9) | (7 << 6) | 0xf)
# define TV_FUSE_STATE_MASK (3 << 4)
/** Read-only state that reports all features enabled */
# define TV_FUSE_STATE_ENABLED (0 << 4)
/** Read-only state that reports that Macrovision is disabled in hardware*/
# define TV_FUSE_STATE_NO_MACROVISION (1 << 4)
/** Read-only state that reports that TV-out is disabled in hardware. */
# define TV_FUSE_STATE_DISABLED (2 << 4)
/** Normal operation */
# define TV_TEST_MODE_NORMAL (0 << 0)
/** Encoder test pattern 1 - combo pattern */
# define TV_TEST_MODE_PATTERN_1 (1 << 0)
/** Encoder test pattern 2 - full screen vertical 75% color bars */
# define TV_TEST_MODE_PATTERN_2 (2 << 0)
/** Encoder test pattern 3 - full screen horizontal 75% color bars */
# define TV_TEST_MODE_PATTERN_3 (3 << 0)
/** Encoder test pattern 4 - random noise */
# define TV_TEST_MODE_PATTERN_4 (4 << 0)
/** Encoder test pattern 5 - linear color ramps */
# define TV_TEST_MODE_PATTERN_5 (5 << 0)
/**
* This test mode forces the DACs to 50% of full output.
*
* This is used for load detection in combination with TVDAC_SENSE_MASK
*/
# define TV_TEST_MODE_MONITOR_DETECT (7 << 0)
# define TV_TEST_MODE_MASK (7 << 0)
#define TV_DAC 0x68004
/**
* Reports that DAC state change logic has reported change (RO).
*
* This gets cleared when TV_DAC_STATE_EN is cleared
*/
# define TVDAC_STATE_CHG (1 << 31)
# define TVDAC_SENSE_MASK (7 << 28)
/** Reports that DAC A voltage is above the detect threshold */
# define TVDAC_A_SENSE (1 << 30)
/** Reports that DAC B voltage is above the detect threshold */
# define TVDAC_B_SENSE (1 << 29)
/** Reports that DAC C voltage is above the detect threshold */
# define TVDAC_C_SENSE (1 << 28)
/**
* Enables DAC state detection logic, for load-based TV detection.
*
* The PLL of the chosen pipe (in TV_CTL) must be running, and the encoder set
* to off, for load detection to work.
*/
# define TVDAC_STATE_CHG_EN (1 << 27)
/** Sets the DAC A sense value to high */
# define TVDAC_A_SENSE_CTL (1 << 26)
/** Sets the DAC B sense value to high */
# define TVDAC_B_SENSE_CTL (1 << 25)
/** Sets the DAC C sense value to high */
# define TVDAC_C_SENSE_CTL (1 << 24)
/** Overrides the ENC_ENABLE and DAC voltage levels */
# define DAC_CTL_OVERRIDE (1 << 7)
/** Sets the slew rate. Must be preserved in software */
# define ENC_TVDAC_SLEW_FAST (1 << 6)
# define DAC_A_1_3_V (0 << 4)
# define DAC_A_1_1_V (1 << 4)
# define DAC_A_0_7_V (2 << 4)
# define DAC_A_MASK (3 << 4)
# define DAC_B_1_3_V (0 << 2)
# define DAC_B_1_1_V (1 << 2)
# define DAC_B_0_7_V (2 << 2)
# define DAC_B_MASK (3 << 2)
# define DAC_C_1_3_V (0 << 0)
# define DAC_C_1_1_V (1 << 0)
# define DAC_C_0_7_V (2 << 0)
# define DAC_C_MASK (3 << 0)
/**
* CSC coefficients are stored in a floating point format with 9 bits of
* mantissa and 2 or 3 bits of exponent. The exponent is represented as 2**-n,
* where 2-bit exponents are unsigned n, and 3-bit exponents are signed n with
* -1 (0x3) being the only legal negative value.
*/
#define TV_CSC_Y 0x68010
# define TV_RY_MASK 0x07ff0000
# define TV_RY_SHIFT 16
# define TV_GY_MASK 0x00000fff
# define TV_GY_SHIFT 0
#define TV_CSC_Y2 0x68014
# define TV_BY_MASK 0x07ff0000
# define TV_BY_SHIFT 16
/**
* Y attenuation for component video.
*
* Stored in 1.9 fixed point.
*/
# define TV_AY_MASK 0x000003ff
# define TV_AY_SHIFT 0
#define TV_CSC_U 0x68018
# define TV_RU_MASK 0x07ff0000
# define TV_RU_SHIFT 16
# define TV_GU_MASK 0x000007ff
# define TV_GU_SHIFT 0
#define TV_CSC_U2 0x6801c
# define TV_BU_MASK 0x07ff0000
# define TV_BU_SHIFT 16
/**
* U attenuation for component video.
*
* Stored in 1.9 fixed point.
*/
# define TV_AU_MASK 0x000003ff
# define TV_AU_SHIFT 0
#define TV_CSC_V 0x68020
# define TV_RV_MASK 0x0fff0000
# define TV_RV_SHIFT 16
# define TV_GV_MASK 0x000007ff
# define TV_GV_SHIFT 0
#define TV_CSC_V2 0x68024
# define TV_BV_MASK 0x07ff0000
# define TV_BV_SHIFT 16
/**
* V attenuation for component video.
*
* Stored in 1.9 fixed point.
*/
# define TV_AV_MASK 0x000007ff
# define TV_AV_SHIFT 0
#define TV_CLR_KNOBS 0x68028
/** 2s-complement brightness adjustment */
# define TV_BRIGHTNESS_MASK 0xff000000
# define TV_BRIGHTNESS_SHIFT 24
/** Contrast adjustment, as a 2.6 unsigned floating point number */
# define TV_CONTRAST_MASK 0x00ff0000
# define TV_CONTRAST_SHIFT 16
/** Saturation adjustment, as a 2.6 unsigned floating point number */
# define TV_SATURATION_MASK 0x0000ff00
# define TV_SATURATION_SHIFT 8
/** Hue adjustment, as an integer phase angle in degrees */
# define TV_HUE_MASK 0x000000ff
# define TV_HUE_SHIFT 0
#define TV_CLR_LEVEL 0x6802c
/** Controls the DAC level for black */
# define TV_BLACK_LEVEL_MASK 0x01ff0000
# define TV_BLACK_LEVEL_SHIFT 16
/** Controls the DAC level for blanking */
# define TV_BLANK_LEVEL_MASK 0x000001ff
# define TV_BLANK_LEVEL_SHIFT 0
#define TV_H_CTL_1 0x68030
/** Number of pixels in the hsync. */
# define TV_HSYNC_END_MASK 0x1fff0000
# define TV_HSYNC_END_SHIFT 16
/** Total number of pixels minus one in the line (display and blanking). */
# define TV_HTOTAL_MASK 0x00001fff
# define TV_HTOTAL_SHIFT 0
#define TV_H_CTL_2 0x68034
/** Enables the colorburst (needed for non-component color) */
# define TV_BURST_ENA (1 << 31)
/** Offset of the colorburst from the start of hsync, in pixels minus one. */
# define TV_HBURST_START_SHIFT 16
# define TV_HBURST_START_MASK 0x1fff0000
/** Length of the colorburst */
# define TV_HBURST_LEN_SHIFT 0
# define TV_HBURST_LEN_MASK 0x0001fff
#define TV_H_CTL_3 0x68038
/** End of hblank, measured in pixels minus one from start of hsync */
# define TV_HBLANK_END_SHIFT 16
# define TV_HBLANK_END_MASK 0x1fff0000
/** Start of hblank, measured in pixels minus one from start of hsync */
# define TV_HBLANK_START_SHIFT 0
# define TV_HBLANK_START_MASK 0x0001fff
#define TV_V_CTL_1 0x6803c
/** XXX */
# define TV_NBR_END_SHIFT 16
# define TV_NBR_END_MASK 0x07ff0000
/** XXX */
# define TV_VI_END_F1_SHIFT 8
# define TV_VI_END_F1_MASK 0x00003f00
/** XXX */
# define TV_VI_END_F2_SHIFT 0
# define TV_VI_END_F2_MASK 0x0000003f
#define TV_V_CTL_2 0x68040
/** Length of vsync, in half lines */
# define TV_VSYNC_LEN_MASK 0x07ff0000
# define TV_VSYNC_LEN_SHIFT 16
/** Offset of the start of vsync in field 1, measured in one less than the
* number of half lines.
*/
# define TV_VSYNC_START_F1_MASK 0x00007f00
# define TV_VSYNC_START_F1_SHIFT 8
/**
* Offset of the start of vsync in field 2, measured in one less than the
* number of half lines.
*/
# define TV_VSYNC_START_F2_MASK 0x0000007f
# define TV_VSYNC_START_F2_SHIFT 0
#define TV_V_CTL_3 0x68044
/** Enables generation of the equalization signal */
# define TV_EQUAL_ENA (1 << 31)
/** Length of vsync, in half lines */
# define TV_VEQ_LEN_MASK 0x007f0000
# define TV_VEQ_LEN_SHIFT 16
/** Offset of the start of equalization in field 1, measured in one less than
* the number of half lines.
*/
# define TV_VEQ_START_F1_MASK 0x0007f00
# define TV_VEQ_START_F1_SHIFT 8
/**
* Offset of the start of equalization in field 2, measured in one less than
* the number of half lines.
*/
# define TV_VEQ_START_F2_MASK 0x000007f
# define TV_VEQ_START_F2_SHIFT 0
#define TV_V_CTL_4 0x68048
/**
* Offset to start of vertical colorburst, measured in one less than the
* number of lines from vertical start.
*/
# define TV_VBURST_START_F1_MASK 0x003f0000
# define TV_VBURST_START_F1_SHIFT 16
/**
* Offset to the end of vertical colorburst, measured in one less than the
* number of lines from the start of NBR.
*/
# define TV_VBURST_END_F1_MASK 0x000000ff
# define TV_VBURST_END_F1_SHIFT 0
#define TV_V_CTL_5 0x6804c
/**
* Offset to start of vertical colorburst, measured in one less than the
* number of lines from vertical start.
*/
# define TV_VBURST_START_F2_MASK 0x003f0000
# define TV_VBURST_START_F2_SHIFT 16
/**
* Offset to the end of vertical colorburst, measured in one less than the
* number of lines from the start of NBR.
*/
# define TV_VBURST_END_F2_MASK 0x000000ff
# define TV_VBURST_END_F2_SHIFT 0
#define TV_V_CTL_6 0x68050
/**
* Offset to start of vertical colorburst, measured in one less than the
* number of lines from vertical start.
*/
# define TV_VBURST_START_F3_MASK 0x003f0000
# define TV_VBURST_START_F3_SHIFT 16
/**
* Offset to the end of vertical colorburst, measured in one less than the
* number of lines from the start of NBR.
*/
# define TV_VBURST_END_F3_MASK 0x000000ff
# define TV_VBURST_END_F3_SHIFT 0
#define TV_V_CTL_7 0x68054
/**
* Offset to start of vertical colorburst, measured in one less than the
* number of lines from vertical start.
*/
# define TV_VBURST_START_F4_MASK 0x003f0000
# define TV_VBURST_START_F4_SHIFT 16
/**
* Offset to the end of vertical colorburst, measured in one less than the
* number of lines from the start of NBR.
*/
# define TV_VBURST_END_F4_MASK 0x000000ff
# define TV_VBURST_END_F4_SHIFT 0
#define TV_SC_CTL_1 0x68060
/** Turns on the first subcarrier phase generation DDA */
# define TV_SC_DDA1_EN (1 << 31)
/** Turns on the first subcarrier phase generation DDA */
# define TV_SC_DDA2_EN (1 << 30)
/** Turns on the first subcarrier phase generation DDA */
# define TV_SC_DDA3_EN (1 << 29)
/** Sets the subcarrier DDA to reset frequency every other field */
# define TV_SC_RESET_EVERY_2 (0 << 24)
/** Sets the subcarrier DDA to reset frequency every fourth field */
# define TV_SC_RESET_EVERY_4 (1 << 24)
/** Sets the subcarrier DDA to reset frequency every eighth field */
# define TV_SC_RESET_EVERY_8 (2 << 24)
/** Sets the subcarrier DDA to never reset the frequency */
# define TV_SC_RESET_NEVER (3 << 24)
/** Sets the peak amplitude of the colorburst.*/
# define TV_BURST_LEVEL_MASK 0x00ff0000
# define TV_BURST_LEVEL_SHIFT 16
/** Sets the increment of the first subcarrier phase generation DDA */
# define TV_SCDDA1_INC_MASK 0x00000fff
# define TV_SCDDA1_INC_SHIFT 0
#define TV_SC_CTL_2 0x68064
/** Sets the rollover for the second subcarrier phase generation DDA */
# define TV_SCDDA2_SIZE_MASK 0x7fff0000
# define TV_SCDDA2_SIZE_SHIFT 16
/** Sets the increent of the second subcarrier phase generation DDA */
# define TV_SCDDA2_INC_MASK 0x00007fff
# define TV_SCDDA2_INC_SHIFT 0
#define TV_SC_CTL_3 0x68068
/** Sets the rollover for the third subcarrier phase generation DDA */
# define TV_SCDDA3_SIZE_MASK 0x7fff0000
# define TV_SCDDA3_SIZE_SHIFT 16
/** Sets the increent of the third subcarrier phase generation DDA */
# define TV_SCDDA3_INC_MASK 0x00007fff
# define TV_SCDDA3_INC_SHIFT 0
#define TV_WIN_POS 0x68070
/** X coordinate of the display from the start of horizontal active */
# define TV_XPOS_MASK 0x1fff0000
# define TV_XPOS_SHIFT 16
/** Y coordinate of the display from the start of vertical active (NBR) */
# define TV_YPOS_MASK 0x00000fff
# define TV_YPOS_SHIFT 0
#define TV_WIN_SIZE 0x68074
/** Horizontal size of the display window, measured in pixels*/
# define TV_XSIZE_MASK 0x1fff0000
# define TV_XSIZE_SHIFT 16
/**
* Vertical size of the display window, measured in pixels.
*
* Must be even for interlaced modes.
*/
# define TV_YSIZE_MASK 0x00000fff
# define TV_YSIZE_SHIFT 0
#define TV_FILTER_CTL_1 0x68080
/**
* Enables automatic scaling calculation.
*
* If set, the rest of the registers are ignored, and the calculated values can
* be read back from the register.
*/
# define TV_AUTO_SCALE (1 << 31)
/**
* Disables the vertical filter.
*
* This is required on modes more than 1024 pixels wide */
# define TV_V_FILTER_BYPASS (1 << 29)
/** Enables adaptive vertical filtering */
# define TV_VADAPT (1 << 28)
# define TV_VADAPT_MODE_MASK (3 << 26)
/** Selects the least adaptive vertical filtering mode */
# define TV_VADAPT_MODE_LEAST (0 << 26)
/** Selects the moderately adaptive vertical filtering mode */
# define TV_VADAPT_MODE_MODERATE (1 << 26)
/** Selects the most adaptive vertical filtering mode */
# define TV_VADAPT_MODE_MOST (3 << 26)
/**
* Sets the horizontal scaling factor.
*
* This should be the fractional part of the horizontal scaling factor divided
* by the oversampling rate. TV_HSCALE should be less than 1, and set to:
*
* (src width - 1) / ((oversample * dest width) - 1)
*/
# define TV_HSCALE_FRAC_MASK 0x00003fff
# define TV_HSCALE_FRAC_SHIFT 0
#define TV_FILTER_CTL_2 0x68084
/**
* Sets the integer part of the 3.15 fixed-point vertical scaling factor.
*
* TV_VSCALE should be (src height - 1) / ((interlace * dest height) - 1)
*/
# define TV_VSCALE_INT_MASK 0x00038000
# define TV_VSCALE_INT_SHIFT 15
/**
* Sets the fractional part of the 3.15 fixed-point vertical scaling factor.
*
* \sa TV_VSCALE_INT_MASK
*/
# define TV_VSCALE_FRAC_MASK 0x00007fff
# define TV_VSCALE_FRAC_SHIFT 0
#define TV_FILTER_CTL_3 0x68088
/**
* Sets the integer part of the 3.15 fixed-point vertical scaling factor.
*
* TV_VSCALE should be (src height - 1) / (1/4 * (dest height - 1))
*
* For progressive modes, TV_VSCALE_IP_INT should be set to zeroes.
*/
# define TV_VSCALE_IP_INT_MASK 0x00038000
# define TV_VSCALE_IP_INT_SHIFT 15
/**
* Sets the fractional part of the 3.15 fixed-point vertical scaling factor.
*
* For progressive modes, TV_VSCALE_IP_INT should be set to zeroes.
*
* \sa TV_VSCALE_IP_INT_MASK
*/
# define TV_VSCALE_IP_FRAC_MASK 0x00007fff
# define TV_VSCALE_IP_FRAC_SHIFT 0
#define TV_CC_CONTROL 0x68090
# define TV_CC_ENABLE (1 << 31)
/**
* Specifies which field to send the CC data in.
*
* CC data is usually sent in field 0.
*/
# define TV_CC_FID_MASK (1 << 27)
# define TV_CC_FID_SHIFT 27
/** Sets the horizontal position of the CC data. Usually 135. */
# define TV_CC_HOFF_MASK 0x03ff0000
# define TV_CC_HOFF_SHIFT 16
/** Sets the vertical position of the CC data. Usually 21 */
# define TV_CC_LINE_MASK 0x0000003f
# define TV_CC_LINE_SHIFT 0
#define TV_CC_DATA 0x68094
# define TV_CC_RDY (1 << 31)
/** Second word of CC data to be transmitted. */
# define TV_CC_DATA_2_MASK 0x007f0000
# define TV_CC_DATA_2_SHIFT 16
/** First word of CC data to be transmitted. */
# define TV_CC_DATA_1_MASK 0x0000007f
# define TV_CC_DATA_1_SHIFT 0
#define TV_H_LUMA_0 0x68100
#define TV_H_LUMA_59 0x681ec
#define TV_H_CHROMA_0 0x68200
#define TV_H_CHROMA_59 0x682ec
#define TV_V_LUMA_0 0x68300
#define TV_V_LUMA_42 0x683a8
#define TV_V_CHROMA_0 0x68400
#define TV_V_CHROMA_42 0x684a8
/* Display Port */
#define DP_B 0x64100
#define DP_C 0x64200
#define DP_D 0x64300
#define DP_PORT_EN (1 << 31)
#define DP_PIPEB_SELECT (1 << 30)
/* Link training mode - select a suitable mode for each stage */
#define DP_LINK_TRAIN_PAT_1 (0 << 28)
#define DP_LINK_TRAIN_PAT_2 (1 << 28)
#define DP_LINK_TRAIN_PAT_IDLE (2 << 28)
#define DP_LINK_TRAIN_OFF (3 << 28)
#define DP_LINK_TRAIN_MASK (3 << 28)
#define DP_LINK_TRAIN_SHIFT 28
/* Signal voltages. These are mostly controlled by the other end */
#define DP_VOLTAGE_0_4 (0 << 25)
#define DP_VOLTAGE_0_6 (1 << 25)
#define DP_VOLTAGE_0_8 (2 << 25)
#define DP_VOLTAGE_1_2 (3 << 25)
#define DP_VOLTAGE_MASK (7 << 25)
#define DP_VOLTAGE_SHIFT 25
/* Signal pre-emphasis levels, like voltages, the other end tells us what
* they want
*/
#define DP_PRE_EMPHASIS_0 (0 << 22)
#define DP_PRE_EMPHASIS_3_5 (1 << 22)
#define DP_PRE_EMPHASIS_6 (2 << 22)
#define DP_PRE_EMPHASIS_9_5 (3 << 22)
#define DP_PRE_EMPHASIS_MASK (7 << 22)
#define DP_PRE_EMPHASIS_SHIFT 22
/* How many wires to use. I guess 3 was too hard */
#define DP_PORT_WIDTH_1 (0 << 19)
#define DP_PORT_WIDTH_2 (1 << 19)
#define DP_PORT_WIDTH_4 (3 << 19)
#define DP_PORT_WIDTH_MASK (7 << 19)
/* Mystic DPCD version 1.1 special mode */
#define DP_ENHANCED_FRAMING (1 << 18)
/** locked once port is enabled */
#define DP_PORT_REVERSAL (1 << 15)
/** sends the clock on lane 15 of the PEG for debug */
#define DP_CLOCK_OUTPUT_ENABLE (1 << 13)
#define DP_SCRAMBLING_DISABLE (1 << 12)
/** limit RGB values to avoid confusing TVs */
#define DP_COLOR_RANGE_16_235 (1 << 8)
/** Turn on the audio link */
#define DP_AUDIO_OUTPUT_ENABLE (1 << 6)
/** vs and hs sync polarity */
#define DP_SYNC_VS_HIGH (1 << 4)
#define DP_SYNC_HS_HIGH (1 << 3)
/** A fantasy */
#define DP_DETECTED (1 << 2)
/** The aux channel provides a way to talk to the
* signal sink for DDC etc. Max packet size supported
* is 20 bytes in each direction, hence the 5 fixed
* data registers
*/
#define DPB_AUX_CH_CTL 0x64110
#define DPB_AUX_CH_DATA1 0x64114
#define DPB_AUX_CH_DATA2 0x64118
#define DPB_AUX_CH_DATA3 0x6411c
#define DPB_AUX_CH_DATA4 0x64120
#define DPB_AUX_CH_DATA5 0x64124
#define DPC_AUX_CH_CTL 0x64210
#define DPC_AUX_CH_DATA1 0x64214
#define DPC_AUX_CH_DATA2 0x64218
#define DPC_AUX_CH_DATA3 0x6421c
#define DPC_AUX_CH_DATA4 0x64220
#define DPC_AUX_CH_DATA5 0x64224
#define DPD_AUX_CH_CTL 0x64310
#define DPD_AUX_CH_DATA1 0x64314
#define DPD_AUX_CH_DATA2 0x64318
#define DPD_AUX_CH_DATA3 0x6431c
#define DPD_AUX_CH_DATA4 0x64320
#define DPD_AUX_CH_DATA5 0x64324
#define DP_AUX_CH_CTL_SEND_BUSY (1 << 31)
#define DP_AUX_CH_CTL_DONE (1 << 30)
#define DP_AUX_CH_CTL_INTERRUPT (1 << 29)
#define DP_AUX_CH_CTL_TIME_OUT_ERROR (1 << 28)
#define DP_AUX_CH_CTL_TIME_OUT_400us (0 << 26)
#define DP_AUX_CH_CTL_TIME_OUT_600us (1 << 26)
#define DP_AUX_CH_CTL_TIME_OUT_800us (2 << 26)
#define DP_AUX_CH_CTL_TIME_OUT_1600us (3 << 26)
#define DP_AUX_CH_CTL_TIME_OUT_MASK (3 << 26)
#define DP_AUX_CH_CTL_RECEIVE_ERROR (1 << 25)
#define DP_AUX_CH_CTL_MESSAGE_SIZE_MASK (0x1f << 20)
#define DP_AUX_CH_CTL_MESSAGE_SIZE_SHIFT 20
#define DP_AUX_CH_CTL_PRECHARGE_2US_MASK (0xf << 16)
#define DP_AUX_CH_CTL_PRECHARGE_2US_SHIFT 16
#define DP_AUX_CH_CTL_AUX_AKSV_SELECT (1 << 15)
#define DP_AUX_CH_CTL_MANCHESTER_TEST (1 << 14)
#define DP_AUX_CH_CTL_SYNC_TEST (1 << 13)
#define DP_AUX_CH_CTL_DEGLITCH_TEST (1 << 12)
#define DP_AUX_CH_CTL_PRECHARGE_TEST (1 << 11)
#define DP_AUX_CH_CTL_BIT_CLOCK_2X_MASK (0x7ff)
#define DP_AUX_CH_CTL_BIT_CLOCK_2X_SHIFT 0
/*
* Computing GMCH M and N values for the Display Port link
*
* GMCH M/N = dot clock * bytes per pixel / ls_clk * # of lanes
*
* ls_clk (we assume) is the DP link clock (1.62 or 2.7 GHz)
*
* The GMCH value is used internally
*
* bytes_per_pixel is the number of bytes coming out of the plane,
* which is after the LUTs, so we want the bytes for our color format.
* For our current usage, this is always 3, one byte for R, G and B.
*/
#define PIPEA_GMCH_DATA_M 0x70050
#define PIPEB_GMCH_DATA_M 0x71050
/* Transfer unit size for display port - 1, default is 0x3f (for TU size 64) */
#define PIPE_GMCH_DATA_M_TU_SIZE_MASK (0x3f << 25)
#define PIPE_GMCH_DATA_M_TU_SIZE_SHIFT 25
#define PIPE_GMCH_DATA_M_MASK (0xffffff)
#define PIPEA_GMCH_DATA_N 0x70054
#define PIPEB_GMCH_DATA_N 0x71054
#define PIPE_GMCH_DATA_N_MASK (0xffffff)
/*
* Computing Link M and N values for the Display Port link
*
* Link M / N = pixel_clock / ls_clk
*
* (the DP spec calls pixel_clock the 'strm_clk')
*
* The Link value is transmitted in the Main Stream
* Attributes and VB-ID.
*/
#define PIPEA_DP_LINK_M 0x70060
#define PIPEB_DP_LINK_M 0x71060
#define PIPEA_DP_LINK_M_MASK (0xffffff)
#define PIPEA_DP_LINK_N 0x70064
#define PIPEB_DP_LINK_N 0x71064
#define PIPEA_DP_LINK_N_MASK (0xffffff)
/* Display & cursor control */
/* Pipe A */
#define PIPEADSL 0x70000
#define PIPEACONF 0x70008
#define PIPEACONF_ENABLE (1<<31)
#define PIPEACONF_DISABLE 0
#define PIPEACONF_DOUBLE_WIDE (1<<30)
#define I965_PIPECONF_ACTIVE (1<<30)
#define PIPEACONF_SINGLE_WIDE 0
#define PIPEACONF_PIPE_UNLOCKED 0
#define PIPEACONF_PIPE_LOCKED (1<<25)
#define PIPEACONF_PALETTE 0
#define PIPEACONF_GAMMA (1<<24)
#define PIPECONF_FORCE_BORDER (1<<25)
#define PIPECONF_PROGRESSIVE (0 << 21)
#define PIPECONF_INTERLACE_W_FIELD_INDICATION (6 << 21)
#define PIPECONF_INTERLACE_FIELD_0_ONLY (7 << 21)
#define PIPEASTAT 0x70024
#define PIPE_FIFO_UNDERRUN_STATUS (1UL<<31)
#define PIPE_CRC_ERROR_ENABLE (1UL<<29)
#define PIPE_CRC_DONE_ENABLE (1UL<<28)
#define PIPE_GMBUS_EVENT_ENABLE (1UL<<27)
#define PIPE_HOTPLUG_INTERRUPT_ENABLE (1UL<<26)
#define PIPE_VSYNC_INTERRUPT_ENABLE (1UL<<25)
#define PIPE_DISPLAY_LINE_COMPARE_ENABLE (1UL<<24)
#define PIPE_DPST_EVENT_ENABLE (1UL<<23)
#define PIPE_LEGACY_BLC_EVENT_ENABLE (1UL<<22)
#define PIPE_ODD_FIELD_INTERRUPT_ENABLE (1UL<<21)
#define PIPE_EVEN_FIELD_INTERRUPT_ENABLE (1UL<<20)
#define PIPE_HOTPLUG_TV_INTERRUPT_ENABLE (1UL<<18) /* pre-965 */
#define PIPE_START_VBLANK_INTERRUPT_ENABLE (1UL<<18) /* 965 or later */
#define PIPE_VBLANK_INTERRUPT_ENABLE (1UL<<17)
#define PIPE_OVERLAY_UPDATED_ENABLE (1UL<<16)
#define PIPE_CRC_ERROR_INTERRUPT_STATUS (1UL<<13)
#define PIPE_CRC_DONE_INTERRUPT_STATUS (1UL<<12)
#define PIPE_GMBUS_INTERRUPT_STATUS (1UL<<11)
#define PIPE_HOTPLUG_INTERRUPT_STATUS (1UL<<10)
#define PIPE_VSYNC_INTERRUPT_STATUS (1UL<<9)
#define PIPE_DISPLAY_LINE_COMPARE_STATUS (1UL<<8)
#define PIPE_DPST_EVENT_STATUS (1UL<<7)
#define PIPE_LEGACY_BLC_EVENT_STATUS (1UL<<6)
#define PIPE_ODD_FIELD_INTERRUPT_STATUS (1UL<<5)
#define PIPE_EVEN_FIELD_INTERRUPT_STATUS (1UL<<4)
#define PIPE_HOTPLUG_TV_INTERRUPT_STATUS (1UL<<2) /* pre-965 */
#define PIPE_START_VBLANK_INTERRUPT_STATUS (1UL<<2) /* 965 or later */
#define PIPE_VBLANK_INTERRUPT_STATUS (1UL<<1)
#define PIPE_OVERLAY_UPDATED_STATUS (1UL<<0)
#define DSPARB 0x70030
#define DSPARB_CSTART_MASK (0x7f << 7)
#define DSPARB_CSTART_SHIFT 7
#define DSPARB_BSTART_MASK (0x7f)
#define DSPARB_BSTART_SHIFT 0
/*
* The two pipe frame counter registers are not synchronized, so
* reading a stable value is somewhat tricky. The following code
* should work:
*
* do {
* high1 = ((INREG(PIPEAFRAMEHIGH) & PIPE_FRAME_HIGH_MASK) >>
* PIPE_FRAME_HIGH_SHIFT;
* low1 = ((INREG(PIPEAFRAMEPIXEL) & PIPE_FRAME_LOW_MASK) >>
* PIPE_FRAME_LOW_SHIFT);
* high2 = ((INREG(PIPEAFRAMEHIGH) & PIPE_FRAME_HIGH_MASK) >>
* PIPE_FRAME_HIGH_SHIFT);
* } while (high1 != high2);
* frame = (high1 << 8) | low1;
*/
#define PIPEAFRAMEHIGH 0x70040
#define PIPE_FRAME_HIGH_MASK 0x0000ffff
#define PIPE_FRAME_HIGH_SHIFT 0
#define PIPEAFRAMEPIXEL 0x70044
#define PIPE_FRAME_LOW_MASK 0xff000000
#define PIPE_FRAME_LOW_SHIFT 24
#define PIPE_PIXEL_MASK 0x00ffffff
#define PIPE_PIXEL_SHIFT 0
/* GM45+ just has to be different */
#define PIPEA_FRMCOUNT_GM45 0x70040
#define PIPEA_FLIPCOUNT_GM45 0x70044
/* Cursor A & B regs */
#define CURACNTR 0x70080
/* Old style CUR*CNTR flags (desktop 8xx) */
#define CURSOR_ENABLE 0x80000000
#define CURSOR_GAMMA_ENABLE 0x40000000
#define CURSOR_STRIDE_MASK 0x30000000
#define CURSOR_FORMAT_SHIFT 24
#define CURSOR_FORMAT_MASK (0x07 << CURSOR_FORMAT_SHIFT)
#define CURSOR_FORMAT_2C (0x00 << CURSOR_FORMAT_SHIFT)
#define CURSOR_FORMAT_3C (0x01 << CURSOR_FORMAT_SHIFT)
#define CURSOR_FORMAT_4C (0x02 << CURSOR_FORMAT_SHIFT)
#define CURSOR_FORMAT_ARGB (0x04 << CURSOR_FORMAT_SHIFT)
#define CURSOR_FORMAT_XRGB (0x05 << CURSOR_FORMAT_SHIFT)
/* New style CUR*CNTR flags */
#define CURSOR_MODE 0x27
#define CURSOR_MODE_DISABLE 0x00
#define CURSOR_MODE_64_32B_AX 0x07
#define CURSOR_MODE_64_ARGB_AX ((1 << 5) | CURSOR_MODE_64_32B_AX)
#define MCURSOR_PIPE_SELECT (1 << 28)
#define MCURSOR_PIPE_A 0x00
#define MCURSOR_PIPE_B (1 << 28)
#define MCURSOR_GAMMA_ENABLE (1 << 26)
#define CURABASE 0x70084
#define CURAPOS 0x70088
#define CURSOR_POS_MASK 0x007FF
#define CURSOR_POS_SIGN 0x8000
#define CURSOR_X_SHIFT 0
#define CURSOR_Y_SHIFT 16
#define CURSIZE 0x700a0
#define CURBCNTR 0x700c0
#define CURBBASE 0x700c4
#define CURBPOS 0x700c8
/* Display A control */
#define DSPACNTR 0x70180
#define DISPLAY_PLANE_ENABLE (1<<31)
#define DISPLAY_PLANE_DISABLE 0
#define DISPPLANE_GAMMA_ENABLE (1<<30)
#define DISPPLANE_GAMMA_DISABLE 0
#define DISPPLANE_PIXFORMAT_MASK (0xf<<26)
#define DISPPLANE_8BPP (0x2<<26)
#define DISPPLANE_15_16BPP (0x4<<26)
#define DISPPLANE_16BPP (0x5<<26)
#define DISPPLANE_32BPP_NO_ALPHA (0x6<<26)
#define DISPPLANE_32BPP (0x7<<26)
#define DISPPLANE_STEREO_ENABLE (1<<25)
#define DISPPLANE_STEREO_DISABLE 0
#define DISPPLANE_SEL_PIPE_MASK (1<<24)
#define DISPPLANE_SEL_PIPE_A 0
#define DISPPLANE_SEL_PIPE_B (1<<24)
#define DISPPLANE_SRC_KEY_ENABLE (1<<22)
#define DISPPLANE_SRC_KEY_DISABLE 0
#define DISPPLANE_LINE_DOUBLE (1<<20)
#define DISPPLANE_NO_LINE_DOUBLE 0
#define DISPPLANE_STEREO_POLARITY_FIRST 0
#define DISPPLANE_STEREO_POLARITY_SECOND (1<<18)
#define DISPPLANE_TILED (1<<10)
#define DSPAADDR 0x70184
#define DSPASTRIDE 0x70188
#define DSPAPOS 0x7018C /* reserved */
#define DSPASIZE 0x70190
#define DSPASURF 0x7019C /* 965+ only */
#define DSPATILEOFF 0x701A4 /* 965+ only */
/* VBIOS flags */
#define SWF00 0x71410
#define SWF01 0x71414
#define SWF02 0x71418
#define SWF03 0x7141c
#define SWF04 0x71420
#define SWF05 0x71424
#define SWF06 0x71428
#define SWF10 0x70410
#define SWF11 0x70414
#define SWF14 0x71420
#define SWF30 0x72414
#define SWF31 0x72418
#define SWF32 0x7241c
/* Pipe B */
#define PIPEBDSL 0x71000
#define PIPEBCONF 0x71008
#define PIPEBSTAT 0x71024
#define PIPEBFRAMEHIGH 0x71040
#define PIPEBFRAMEPIXEL 0x71044
#define PIPEB_FRMCOUNT_GM45 0x71040
#define PIPEB_FLIPCOUNT_GM45 0x71044
/* Display B control */
#define DSPBCNTR 0x71180
#define DISPPLANE_ALPHA_TRANS_ENABLE (1<<15)
#define DISPPLANE_ALPHA_TRANS_DISABLE 0
#define DISPPLANE_SPRITE_ABOVE_DISPLAY 0
#define DISPPLANE_SPRITE_ABOVE_OVERLAY (1)
#define DSPBADDR 0x71184
#define DSPBSTRIDE 0x71188
#define DSPBPOS 0x7118C
#define DSPBSIZE 0x71190
#define DSPBSURF 0x7119C
#define DSPBTILEOFF 0x711A4
/* VBIOS regs */
#define VGACNTRL 0x71400
# define VGA_DISP_DISABLE (1 << 31)
# define VGA_2X_MODE (1 << 30)
# define VGA_PIPE_B_SELECT (1 << 29)
/* IGDNG */
#define CPU_VGACNTRL 0x41000
#define DIGITAL_PORT_HOTPLUG_CNTRL 0x44030
#define DIGITAL_PORTA_HOTPLUG_ENABLE (1 << 4)
#define DIGITAL_PORTA_SHORT_PULSE_2MS (0 << 2)
#define DIGITAL_PORTA_SHORT_PULSE_4_5MS (1 << 2)
#define DIGITAL_PORTA_SHORT_PULSE_6MS (2 << 2)
#define DIGITAL_PORTA_SHORT_PULSE_100MS (3 << 2)
#define DIGITAL_PORTA_NO_DETECT (0 << 0)
#define DIGITAL_PORTA_LONG_PULSE_DETECT_MASK (1 << 1)
#define DIGITAL_PORTA_SHORT_PULSE_DETECT_MASK (1 << 0)
/* refresh rate hardware control */
#define RR_HW_CTL 0x45300
#define RR_HW_LOW_POWER_FRAMES_MASK 0xff
#define RR_HW_HIGH_POWER_FRAMES_MASK 0xff00
#define FDI_PLL_BIOS_0 0x46000
#define FDI_PLL_BIOS_1 0x46004
#define FDI_PLL_BIOS_2 0x46008
#define DISPLAY_PORT_PLL_BIOS_0 0x4600c
#define DISPLAY_PORT_PLL_BIOS_1 0x46010
#define DISPLAY_PORT_PLL_BIOS_2 0x46014
#define FDI_PLL_FREQ_CTL 0x46030
#define FDI_PLL_FREQ_CHANGE_REQUEST (1<<24)
#define FDI_PLL_FREQ_LOCK_LIMIT_MASK 0xfff00
#define FDI_PLL_FREQ_DISABLE_COUNT_LIMIT_MASK 0xff
#define PIPEA_DATA_M1 0x60030
#define TU_SIZE(x) (((x)-1) << 25) /* default size 64 */
#define TU_SIZE_MASK 0x7e000000
#define PIPEA_DATA_M1_OFFSET 0
#define PIPEA_DATA_N1 0x60034
#define PIPEA_DATA_N1_OFFSET 0
#define PIPEA_DATA_M2 0x60038
#define PIPEA_DATA_M2_OFFSET 0
#define PIPEA_DATA_N2 0x6003c
#define PIPEA_DATA_N2_OFFSET 0
#define PIPEA_LINK_M1 0x60040
#define PIPEA_LINK_M1_OFFSET 0
#define PIPEA_LINK_N1 0x60044
#define PIPEA_LINK_N1_OFFSET 0
#define PIPEA_LINK_M2 0x60048
#define PIPEA_LINK_M2_OFFSET 0
#define PIPEA_LINK_N2 0x6004c
#define PIPEA_LINK_N2_OFFSET 0
/* PIPEB timing regs are same start from 0x61000 */
#define PIPEB_DATA_M1 0x61030
#define PIPEB_DATA_M1_OFFSET 0
#define PIPEB_DATA_N1 0x61034
#define PIPEB_DATA_N1_OFFSET 0
#define PIPEB_DATA_M2 0x61038
#define PIPEB_DATA_M2_OFFSET 0
#define PIPEB_DATA_N2 0x6103c
#define PIPEB_DATA_N2_OFFSET 0
#define PIPEB_LINK_M1 0x61040
#define PIPEB_LINK_M1_OFFSET 0
#define PIPEB_LINK_N1 0x61044
#define PIPEB_LINK_N1_OFFSET 0
#define PIPEB_LINK_M2 0x61048
#define PIPEB_LINK_M2_OFFSET 0
#define PIPEB_LINK_N2 0x6104c
#define PIPEB_LINK_N2_OFFSET 0
/* CPU panel fitter */
#define PFA_CTL_1 0x68080
#define PFB_CTL_1 0x68880
#define PF_ENABLE (1<<31)
/* legacy palette */
#define LGC_PALETTE_A 0x4a000
#define LGC_PALETTE_B 0x4a800
/* interrupts */
#define DE_MASTER_IRQ_CONTROL (1 << 31)
#define DE_SPRITEB_FLIP_DONE (1 << 29)
#define DE_SPRITEA_FLIP_DONE (1 << 28)
#define DE_PLANEB_FLIP_DONE (1 << 27)
#define DE_PLANEA_FLIP_DONE (1 << 26)
#define DE_PCU_EVENT (1 << 25)
#define DE_GTT_FAULT (1 << 24)
#define DE_POISON (1 << 23)
#define DE_PERFORM_COUNTER (1 << 22)
#define DE_PCH_EVENT (1 << 21)
#define DE_AUX_CHANNEL_A (1 << 20)
#define DE_DP_A_HOTPLUG (1 << 19)
#define DE_GSE (1 << 18)
#define DE_PIPEB_VBLANK (1 << 15)
#define DE_PIPEB_EVEN_FIELD (1 << 14)
#define DE_PIPEB_ODD_FIELD (1 << 13)
#define DE_PIPEB_LINE_COMPARE (1 << 12)
#define DE_PIPEB_VSYNC (1 << 11)
#define DE_PIPEB_FIFO_UNDERRUN (1 << 8)
#define DE_PIPEA_VBLANK (1 << 7)
#define DE_PIPEA_EVEN_FIELD (1 << 6)
#define DE_PIPEA_ODD_FIELD (1 << 5)
#define DE_PIPEA_LINE_COMPARE (1 << 4)
#define DE_PIPEA_VSYNC (1 << 3)
#define DE_PIPEA_FIFO_UNDERRUN (1 << 0)
#define DEISR 0x44000
#define DEIMR 0x44004
#define DEIIR 0x44008
#define DEIER 0x4400c
/* GT interrupt */
#define GT_SYNC_STATUS (1 << 2)
#define GT_USER_INTERRUPT (1 << 0)
#define GTISR 0x44010
#define GTIMR 0x44014
#define GTIIR 0x44018
#define GTIER 0x4401c
/* PCH */
/* south display engine interrupt */
#define SDE_CRT_HOTPLUG (1 << 11)
#define SDE_PORTD_HOTPLUG (1 << 10)
#define SDE_PORTC_HOTPLUG (1 << 9)
#define SDE_PORTB_HOTPLUG (1 << 8)
#define SDE_SDVOB_HOTPLUG (1 << 6)
#define SDEISR 0xc4000
#define SDEIMR 0xc4004
#define SDEIIR 0xc4008
#define SDEIER 0xc400c
/* digital port hotplug */
#define PCH_PORT_HOTPLUG 0xc4030
#define PORTD_HOTPLUG_ENABLE (1 << 20)
#define PORTD_PULSE_DURATION_2ms (0)
#define PORTD_PULSE_DURATION_4_5ms (1 << 18)
#define PORTD_PULSE_DURATION_6ms (2 << 18)
#define PORTD_PULSE_DURATION_100ms (3 << 18)
#define PORTD_HOTPLUG_NO_DETECT (0)
#define PORTD_HOTPLUG_SHORT_DETECT (1 << 16)
#define PORTD_HOTPLUG_LONG_DETECT (1 << 17)
#define PORTC_HOTPLUG_ENABLE (1 << 12)
#define PORTC_PULSE_DURATION_2ms (0)
#define PORTC_PULSE_DURATION_4_5ms (1 << 10)
#define PORTC_PULSE_DURATION_6ms (2 << 10)
#define PORTC_PULSE_DURATION_100ms (3 << 10)
#define PORTC_HOTPLUG_NO_DETECT (0)
#define PORTC_HOTPLUG_SHORT_DETECT (1 << 8)
#define PORTC_HOTPLUG_LONG_DETECT (1 << 9)
#define PORTB_HOTPLUG_ENABLE (1 << 4)
#define PORTB_PULSE_DURATION_2ms (0)
#define PORTB_PULSE_DURATION_4_5ms (1 << 2)
#define PORTB_PULSE_DURATION_6ms (2 << 2)
#define PORTB_PULSE_DURATION_100ms (3 << 2)
#define PORTB_HOTPLUG_NO_DETECT (0)
#define PORTB_HOTPLUG_SHORT_DETECT (1 << 0)
#define PORTB_HOTPLUG_LONG_DETECT (1 << 1)
#define PCH_GPIOA 0xc5010
#define PCH_GPIOB 0xc5014
#define PCH_GPIOC 0xc5018
#define PCH_GPIOD 0xc501c
#define PCH_GPIOE 0xc5020
#define PCH_GPIOF 0xc5024
#define PCH_DPLL_A 0xc6014
#define PCH_DPLL_B 0xc6018
#define PCH_FPA0 0xc6040
#define PCH_FPA1 0xc6044
#define PCH_FPB0 0xc6048
#define PCH_FPB1 0xc604c
#define PCH_DPLL_TEST 0xc606c
#define PCH_DREF_CONTROL 0xC6200
#define DREF_CONTROL_MASK 0x7fc3
#define DREF_CPU_SOURCE_OUTPUT_DISABLE (0<<13)
#define DREF_CPU_SOURCE_OUTPUT_DOWNSPREAD (2<<13)
#define DREF_CPU_SOURCE_OUTPUT_NONSPREAD (3<<13)
#define DREF_CPU_SOURCE_OUTPUT_MASK (3<<13)
#define DREF_SSC_SOURCE_DISABLE (0<<11)
#define DREF_SSC_SOURCE_ENABLE (2<<11)
#define DREF_SSC_SOURCE_MASK (2<<11)
#define DREF_NONSPREAD_SOURCE_DISABLE (0<<9)
#define DREF_NONSPREAD_CK505_ENABLE (1<<9)
#define DREF_NONSPREAD_SOURCE_ENABLE (2<<9)
#define DREF_NONSPREAD_SOURCE_MASK (2<<9)
#define DREF_SUPERSPREAD_SOURCE_DISABLE (0<<7)
#define DREF_SUPERSPREAD_SOURCE_ENABLE (2<<7)
#define DREF_SSC4_DOWNSPREAD (0<<6)
#define DREF_SSC4_CENTERSPREAD (1<<6)
#define DREF_SSC1_DISABLE (0<<1)
#define DREF_SSC1_ENABLE (1<<1)
#define DREF_SSC4_DISABLE (0)
#define DREF_SSC4_ENABLE (1)
#define PCH_RAWCLK_FREQ 0xc6204
#define FDL_TP1_TIMER_SHIFT 12
#define FDL_TP1_TIMER_MASK (3<<12)
#define FDL_TP2_TIMER_SHIFT 10
#define FDL_TP2_TIMER_MASK (3<<10)
#define RAWCLK_FREQ_MASK 0x3ff
#define PCH_DPLL_TMR_CFG 0xc6208
#define PCH_SSC4_PARMS 0xc6210
#define PCH_SSC4_AUX_PARMS 0xc6214
/* transcoder */
#define TRANS_HTOTAL_A 0xe0000
#define TRANS_HTOTAL_SHIFT 16
#define TRANS_HACTIVE_SHIFT 0
#define TRANS_HBLANK_A 0xe0004
#define TRANS_HBLANK_END_SHIFT 16
#define TRANS_HBLANK_START_SHIFT 0
#define TRANS_HSYNC_A 0xe0008
#define TRANS_HSYNC_END_SHIFT 16
#define TRANS_HSYNC_START_SHIFT 0
#define TRANS_VTOTAL_A 0xe000c
#define TRANS_VTOTAL_SHIFT 16
#define TRANS_VACTIVE_SHIFT 0
#define TRANS_VBLANK_A 0xe0010
#define TRANS_VBLANK_END_SHIFT 16
#define TRANS_VBLANK_START_SHIFT 0
#define TRANS_VSYNC_A 0xe0014
#define TRANS_VSYNC_END_SHIFT 16
#define TRANS_VSYNC_START_SHIFT 0
#define TRANSA_DATA_M1 0xe0030
#define TRANSA_DATA_N1 0xe0034
#define TRANSA_DATA_M2 0xe0038
#define TRANSA_DATA_N2 0xe003c
#define TRANSA_DP_LINK_M1 0xe0040
#define TRANSA_DP_LINK_N1 0xe0044
#define TRANSA_DP_LINK_M2 0xe0048
#define TRANSA_DP_LINK_N2 0xe004c
#define TRANS_HTOTAL_B 0xe1000
#define TRANS_HBLANK_B 0xe1004
#define TRANS_HSYNC_B 0xe1008
#define TRANS_VTOTAL_B 0xe100c
#define TRANS_VBLANK_B 0xe1010
#define TRANS_VSYNC_B 0xe1014
#define TRANSB_DATA_M1 0xe1030
#define TRANSB_DATA_N1 0xe1034
#define TRANSB_DATA_M2 0xe1038
#define TRANSB_DATA_N2 0xe103c
#define TRANSB_DP_LINK_M1 0xe1040
#define TRANSB_DP_LINK_N1 0xe1044
#define TRANSB_DP_LINK_M2 0xe1048
#define TRANSB_DP_LINK_N2 0xe104c
#define TRANSACONF 0xf0008
#define TRANSBCONF 0xf1008
#define TRANS_DISABLE (0<<31)
#define TRANS_ENABLE (1<<31)
#define TRANS_STATE_MASK (1<<30)
#define TRANS_STATE_DISABLE (0<<30)
#define TRANS_STATE_ENABLE (1<<30)
#define TRANS_FSYNC_DELAY_HB1 (0<<27)
#define TRANS_FSYNC_DELAY_HB2 (1<<27)
#define TRANS_FSYNC_DELAY_HB3 (2<<27)
#define TRANS_FSYNC_DELAY_HB4 (3<<27)
#define TRANS_DP_AUDIO_ONLY (1<<26)
#define TRANS_DP_VIDEO_AUDIO (0<<26)
#define TRANS_PROGRESSIVE (0<<21)
#define TRANS_8BPC (0<<5)
#define TRANS_10BPC (1<<5)
#define TRANS_6BPC (2<<5)
#define TRANS_12BPC (3<<5)
#define FDI_RXA_CHICKEN 0xc200c
#define FDI_RXB_CHICKEN 0xc2010
#define FDI_RX_PHASE_SYNC_POINTER_ENABLE (1)
/* CPU: FDI_TX */
#define FDI_TXA_CTL 0x60100
#define FDI_TXB_CTL 0x61100
#define FDI_TX_DISABLE (0<<31)
#define FDI_TX_ENABLE (1<<31)
#define FDI_LINK_TRAIN_PATTERN_1 (0<<28)
#define FDI_LINK_TRAIN_PATTERN_2 (1<<28)
#define FDI_LINK_TRAIN_PATTERN_IDLE (2<<28)
#define FDI_LINK_TRAIN_NONE (3<<28)
#define FDI_LINK_TRAIN_VOLTAGE_0_4V (0<<25)
#define FDI_LINK_TRAIN_VOLTAGE_0_6V (1<<25)
#define FDI_LINK_TRAIN_VOLTAGE_0_8V (2<<25)
#define FDI_LINK_TRAIN_VOLTAGE_1_2V (3<<25)
#define FDI_LINK_TRAIN_PRE_EMPHASIS_NONE (0<<22)
#define FDI_LINK_TRAIN_PRE_EMPHASIS_1_5X (1<<22)
#define FDI_LINK_TRAIN_PRE_EMPHASIS_2X (2<<22)
#define FDI_LINK_TRAIN_PRE_EMPHASIS_3X (3<<22)
#define FDI_DP_PORT_WIDTH_X1 (0<<19)
#define FDI_DP_PORT_WIDTH_X2 (1<<19)
#define FDI_DP_PORT_WIDTH_X3 (2<<19)
#define FDI_DP_PORT_WIDTH_X4 (3<<19)
#define FDI_TX_ENHANCE_FRAME_ENABLE (1<<18)
/* IGDNG: hardwired to 1 */
#define FDI_TX_PLL_ENABLE (1<<14)
/* both Tx and Rx */
#define FDI_SCRAMBLING_ENABLE (0<<7)
#define FDI_SCRAMBLING_DISABLE (1<<7)
/* FDI_RX, FDI_X is hard-wired to Transcoder_X */
#define FDI_RXA_CTL 0xf000c
#define FDI_RXB_CTL 0xf100c
#define FDI_RX_ENABLE (1<<31)
#define FDI_RX_DISABLE (0<<31)
/* train, dp width same as FDI_TX */
#define FDI_DP_PORT_WIDTH_X8 (7<<19)
#define FDI_8BPC (0<<16)
#define FDI_10BPC (1<<16)
#define FDI_6BPC (2<<16)
#define FDI_12BPC (3<<16)
#define FDI_LINK_REVERSE_OVERWRITE (1<<15)
#define FDI_DMI_LINK_REVERSE_MASK (1<<14)
#define FDI_RX_PLL_ENABLE (1<<13)
#define FDI_FS_ERR_CORRECT_ENABLE (1<<11)
#define FDI_FE_ERR_CORRECT_ENABLE (1<<10)
#define FDI_FS_ERR_REPORT_ENABLE (1<<9)
#define FDI_FE_ERR_REPORT_ENABLE (1<<8)
#define FDI_RX_ENHANCE_FRAME_ENABLE (1<<6)
#define FDI_SEL_RAWCLK (0<<4)
#define FDI_SEL_PCDCLK (1<<4)
#define FDI_RXA_MISC 0xf0010
#define FDI_RXB_MISC 0xf1010
#define FDI_RXA_TUSIZE1 0xf0030
#define FDI_RXA_TUSIZE2 0xf0038
#define FDI_RXB_TUSIZE1 0xf1030
#define FDI_RXB_TUSIZE2 0xf1038
/* FDI_RX interrupt register format */
#define FDI_RX_INTER_LANE_ALIGN (1<<10)
#define FDI_RX_SYMBOL_LOCK (1<<9) /* train 2 */
#define FDI_RX_BIT_LOCK (1<<8) /* train 1 */
#define FDI_RX_TRAIN_PATTERN_2_FAIL (1<<7)
#define FDI_RX_FS_CODE_ERR (1<<6)
#define FDI_RX_FE_CODE_ERR (1<<5)
#define FDI_RX_SYMBOL_ERR_RATE_ABOVE (1<<4)
#define FDI_RX_HDCP_LINK_FAIL (1<<3)
#define FDI_RX_PIXEL_FIFO_OVERFLOW (1<<2)
#define FDI_RX_CROSS_CLOCK_OVERFLOW (1<<1)
#define FDI_RX_SYMBOL_QUEUE_OVERFLOW (1<<0)
#define FDI_RXA_IIR 0xf0014
#define FDI_RXA_IMR 0xf0018
#define FDI_RXB_IIR 0xf1014
#define FDI_RXB_IMR 0xf1018
#define FDI_PLL_CTL_1 0xfe000
#define FDI_PLL_CTL_2 0xfe004
/* CRT */
#define PCH_ADPA 0xe1100
#define ADPA_TRANS_SELECT_MASK (1<<30)
#define ADPA_TRANS_A_SELECT 0
#define ADPA_TRANS_B_SELECT (1<<30)
#define ADPA_CRT_HOTPLUG_MASK 0x03ff0000 /* bit 25-16 */
#define ADPA_CRT_HOTPLUG_MONITOR_NONE (0<<24)
#define ADPA_CRT_HOTPLUG_MONITOR_MASK (3<<24)
#define ADPA_CRT_HOTPLUG_MONITOR_COLOR (3<<24)
#define ADPA_CRT_HOTPLUG_MONITOR_MONO (2<<24)
#define ADPA_CRT_HOTPLUG_ENABLE (1<<23)
#define ADPA_CRT_HOTPLUG_PERIOD_64 (0<<22)
#define ADPA_CRT_HOTPLUG_PERIOD_128 (1<<22)
#define ADPA_CRT_HOTPLUG_WARMUP_5MS (0<<21)
#define ADPA_CRT_HOTPLUG_WARMUP_10MS (1<<21)
#define ADPA_CRT_HOTPLUG_SAMPLE_2S (0<<20)
#define ADPA_CRT_HOTPLUG_SAMPLE_4S (1<<20)
#define ADPA_CRT_HOTPLUG_VOLTAGE_40 (0<<18)
#define ADPA_CRT_HOTPLUG_VOLTAGE_50 (1<<18)
#define ADPA_CRT_HOTPLUG_VOLTAGE_60 (2<<18)
#define ADPA_CRT_HOTPLUG_VOLTAGE_70 (3<<18)
#define ADPA_CRT_HOTPLUG_VOLREF_325MV (0<<17)
#define ADPA_CRT_HOTPLUG_VOLREF_475MV (1<<17)
#define ADPA_CRT_HOTPLUG_FORCE_TRIGGER (1<<16)
/* or SDVOB */
#define HDMIB 0xe1140
#define PORT_ENABLE (1 << 31)
#define TRANSCODER_A (0)
#define TRANSCODER_B (1 << 30)
#define COLOR_FORMAT_8bpc (0)
#define COLOR_FORMAT_12bpc (3 << 26)
#define SDVOB_HOTPLUG_ENABLE (1 << 23)
#define SDVO_ENCODING (0)
#define TMDS_ENCODING (2 << 10)
#define NULL_PACKET_VSYNC_ENABLE (1 << 9)
#define SDVOB_BORDER_ENABLE (1 << 7)
#define AUDIO_ENABLE (1 << 6)
#define VSYNC_ACTIVE_HIGH (1 << 4)
#define HSYNC_ACTIVE_HIGH (1 << 3)
#define PORT_DETECTED (1 << 2)
#define HDMIC 0xe1150
#define HDMID 0xe1160
#define PCH_LVDS 0xe1180
#define LVDS_DETECTED (1 << 1)
#define BLC_PWM_CPU_CTL2 0x48250
#define PWM_ENABLE (1 << 31)
#define PWM_PIPE_A (0 << 29)
#define PWM_PIPE_B (1 << 29)
#define BLC_PWM_CPU_CTL 0x48254
#define BLC_PWM_PCH_CTL1 0xc8250
#define PWM_PCH_ENABLE (1 << 31)
#define PWM_POLARITY_ACTIVE_LOW (1 << 29)
#define PWM_POLARITY_ACTIVE_HIGH (0 << 29)
#define PWM_POLARITY_ACTIVE_LOW2 (1 << 28)
#define PWM_POLARITY_ACTIVE_HIGH2 (0 << 28)
#define BLC_PWM_PCH_CTL2 0xc8254
#define PCH_PP_STATUS 0xc7200
#define PCH_PP_CONTROL 0xc7204
#define EDP_FORCE_VDD (1 << 3)
#define EDP_BLC_ENABLE (1 << 2)
#define PANEL_POWER_RESET (1 << 1)
#define PANEL_POWER_OFF (0 << 0)
#define PANEL_POWER_ON (1 << 0)
#define PCH_PP_ON_DELAYS 0xc7208
#define EDP_PANEL (1 << 30)
#define PCH_PP_OFF_DELAYS 0xc720c
#define PCH_PP_DIVISOR 0xc7210
#endif /* _I915_REG_H_ */