| /************************************************************************/ |
| /* */ |
| /* dc395x.h */ |
| /* */ |
| /* Device Driver for Tekram DC395(U/UW/F), DC315(U) */ |
| /* PCI SCSI Bus Master Host Adapter */ |
| /* (SCSI chip set used Tekram ASIC TRM-S1040) */ |
| /* */ |
| /************************************************************************/ |
| #ifndef DC395x_H |
| #define DC395x_H |
| |
| /************************************************************************/ |
| /* */ |
| /* Initial values */ |
| /* */ |
| /************************************************************************/ |
| #define DC395x_MAX_CMD_QUEUE 32 |
| /* #define DC395x_MAX_QTAGS 32 */ |
| #define DC395x_MAX_QTAGS 16 |
| #define DC395x_MAX_SCSI_ID 16 |
| #define DC395x_MAX_CMD_PER_LUN DC395x_MAX_QTAGS |
| #define DC395x_MAX_SG_TABLESIZE 64 /* HW limitation */ |
| #define DC395x_MAX_SG_LISTENTRY 64 /* Must be equal or lower to previous */ |
| /* item */ |
| #define DC395x_MAX_SRB_CNT 63 |
| /* #define DC395x_MAX_CAN_QUEUE 7 * DC395x_MAX_QTAGS */ |
| #define DC395x_MAX_CAN_QUEUE DC395x_MAX_SRB_CNT |
| #define DC395x_END_SCAN 2 |
| #define DC395x_SEL_TIMEOUT 153 /* 250 ms selection timeout (@ 40 MHz) */ |
| #define DC395x_MAX_RETRIES 3 |
| |
| #if 0 |
| #define SYNC_FIRST |
| #endif |
| |
| #define NORM_REC_LVL 0 |
| |
| /************************************************************************/ |
| /* */ |
| /* Various definitions */ |
| /* */ |
| /************************************************************************/ |
| #define BIT31 0x80000000 |
| #define BIT30 0x40000000 |
| #define BIT29 0x20000000 |
| #define BIT28 0x10000000 |
| #define BIT27 0x08000000 |
| #define BIT26 0x04000000 |
| #define BIT25 0x02000000 |
| #define BIT24 0x01000000 |
| #define BIT23 0x00800000 |
| #define BIT22 0x00400000 |
| #define BIT21 0x00200000 |
| #define BIT20 0x00100000 |
| #define BIT19 0x00080000 |
| #define BIT18 0x00040000 |
| #define BIT17 0x00020000 |
| #define BIT16 0x00010000 |
| #define BIT15 0x00008000 |
| #define BIT14 0x00004000 |
| #define BIT13 0x00002000 |
| #define BIT12 0x00001000 |
| #define BIT11 0x00000800 |
| #define BIT10 0x00000400 |
| #define BIT9 0x00000200 |
| #define BIT8 0x00000100 |
| #define BIT7 0x00000080 |
| #define BIT6 0x00000040 |
| #define BIT5 0x00000020 |
| #define BIT4 0x00000010 |
| #define BIT3 0x00000008 |
| #define BIT2 0x00000004 |
| #define BIT1 0x00000002 |
| #define BIT0 0x00000001 |
| |
| /* UnitCtrlFlag */ |
| #define UNIT_ALLOCATED BIT0 |
| #define UNIT_INFO_CHANGED BIT1 |
| #define FORMATING_MEDIA BIT2 |
| #define UNIT_RETRY BIT3 |
| |
| /* UnitFlags */ |
| #define DASD_SUPPORT BIT0 |
| #define SCSI_SUPPORT BIT1 |
| #define ASPI_SUPPORT BIT2 |
| |
| /* SRBState machine definition */ |
| #define SRB_FREE 0x0000 |
| #define SRB_WAIT 0x0001 |
| #define SRB_READY 0x0002 |
| #define SRB_MSGOUT 0x0004 /* arbitration+msg_out 1st byte */ |
| #define SRB_MSGIN 0x0008 |
| #define SRB_EXTEND_MSGIN 0x0010 |
| #define SRB_COMMAND 0x0020 |
| #define SRB_START_ 0x0040 /* arbitration+msg_out+command_out */ |
| #define SRB_DISCONNECT 0x0080 |
| #define SRB_DATA_XFER 0x0100 |
| #define SRB_XFERPAD 0x0200 |
| #define SRB_STATUS 0x0400 |
| #define SRB_COMPLETED 0x0800 |
| #define SRB_ABORT_SENT 0x1000 |
| #define SRB_DO_SYNC_NEGO 0x2000 |
| #define SRB_DO_WIDE_NEGO 0x4000 |
| #define SRB_UNEXPECT_RESEL 0x8000 |
| |
| /************************************************************************/ |
| /* */ |
| /* ACB Config */ |
| /* */ |
| /************************************************************************/ |
| #define HCC_WIDE_CARD 0x20 |
| #define HCC_SCSI_RESET 0x10 |
| #define HCC_PARITY 0x08 |
| #define HCC_AUTOTERM 0x04 |
| #define HCC_LOW8TERM 0x02 |
| #define HCC_UP8TERM 0x01 |
| |
| /* ACBFlag */ |
| #define RESET_DEV BIT0 |
| #define RESET_DETECT BIT1 |
| #define RESET_DONE BIT2 |
| |
| /* DCBFlag */ |
| #define ABORT_DEV_ BIT0 |
| |
| /* SRBstatus */ |
| #define SRB_OK BIT0 |
| #define ABORTION BIT1 |
| #define OVER_RUN BIT2 |
| #define UNDER_RUN BIT3 |
| #define PARITY_ERROR BIT4 |
| #define SRB_ERROR BIT5 |
| |
| /* SRBFlag */ |
| #define DATAOUT BIT7 |
| #define DATAIN BIT6 |
| #define RESIDUAL_VALID BIT5 |
| #define ENABLE_TIMER BIT4 |
| #define RESET_DEV0 BIT2 |
| #define ABORT_DEV BIT1 |
| #define AUTO_REQSENSE BIT0 |
| |
| /* Adapter status */ |
| #define H_STATUS_GOOD 0 |
| #define H_SEL_TIMEOUT 0x11 |
| #define H_OVER_UNDER_RUN 0x12 |
| #define H_UNEXP_BUS_FREE 0x13 |
| #define H_TARGET_PHASE_F 0x14 |
| #define H_INVALID_CCB_OP 0x16 |
| #define H_LINK_CCB_BAD 0x17 |
| #define H_BAD_TARGET_DIR 0x18 |
| #define H_DUPLICATE_CCB 0x19 |
| #define H_BAD_CCB_OR_SG 0x1A |
| #define H_ABORT 0x0FF |
| |
| /* SCSI BUS Status byte codes */ |
| #define SCSI_STAT_GOOD 0x0 /* Good status */ |
| #define SCSI_STAT_CHECKCOND 0x02 /* SCSI Check Condition */ |
| #define SCSI_STAT_CONDMET 0x04 /* Condition Met */ |
| #define SCSI_STAT_BUSY 0x08 /* Target busy status */ |
| #define SCSI_STAT_INTER 0x10 /* Intermediate status */ |
| #define SCSI_STAT_INTERCONDMET 0x14 /* Intermediate condition met */ |
| #define SCSI_STAT_RESCONFLICT 0x18 /* Reservation conflict */ |
| #define SCSI_STAT_CMDTERM 0x22 /* Command Terminated */ |
| #define SCSI_STAT_QUEUEFULL 0x28 /* Queue Full */ |
| #define SCSI_STAT_UNEXP_BUS_F 0xFD /* Unexpect Bus Free */ |
| #define SCSI_STAT_BUS_RST_DETECT 0xFE /* Scsi Bus Reset detected */ |
| #define SCSI_STAT_SEL_TIMEOUT 0xFF /* Selection Time out */ |
| |
| /* Sync_Mode */ |
| #define SYNC_WIDE_TAG_ATNT_DISABLE 0 |
| #define SYNC_NEGO_ENABLE BIT0 |
| #define SYNC_NEGO_DONE BIT1 |
| #define WIDE_NEGO_ENABLE BIT2 |
| #define WIDE_NEGO_DONE BIT3 |
| #define WIDE_NEGO_STATE BIT4 |
| #define EN_TAG_QUEUEING BIT5 |
| #define EN_ATN_STOP BIT6 |
| |
| #define SYNC_NEGO_OFFSET 15 |
| |
| /* SCSI MSG BYTE */ |
| #define MSG_COMPLETE 0x00 |
| #define MSG_EXTENDED 0x01 |
| #define MSG_SAVE_PTR 0x02 |
| #define MSG_RESTORE_PTR 0x03 |
| #define MSG_DISCONNECT 0x04 |
| #define MSG_INITIATOR_ERROR 0x05 |
| #define MSG_ABORT 0x06 |
| #define MSG_REJECT_ 0x07 |
| #define MSG_NOP 0x08 |
| #define MSG_PARITY_ERROR 0x09 |
| #define MSG_LINK_CMD_COMPL 0x0A |
| #define MSG_LINK_CMD_COMPL_FLG 0x0B |
| #define MSG_BUS_RESET 0x0C |
| #define MSG_ABORT_TAG 0x0D |
| #define MSG_SIMPLE_QTAG 0x20 |
| #define MSG_HEAD_QTAG 0x21 |
| #define MSG_ORDER_QTAG 0x22 |
| #define MSG_IGNOREWIDE 0x23 |
| #define MSG_IDENTIFY 0x80 |
| #define MSG_HOST_ID 0xC0 |
| |
| /* SCSI STATUS BYTE */ |
| #define STATUS_GOOD 0x00 |
| #define CHECK_CONDITION_ 0x02 |
| #define STATUS_BUSY 0x08 |
| #define STATUS_INTERMEDIATE 0x10 |
| #define RESERVE_CONFLICT 0x18 |
| |
| /* cmd->result */ |
| #define STATUS_MASK_ 0xFF |
| #define MSG_MASK 0xFF00 |
| #define RETURN_MASK 0xFF0000 |
| |
| /************************************************************************/ |
| /* */ |
| /* Inquiry Data format */ |
| /* */ |
| /************************************************************************/ |
| struct ScsiInqData |
| { /* INQ */ |
| u8 DevType; /* Periph Qualifier & Periph Dev Type */ |
| u8 RMB_TypeMod; /* rem media bit & Dev Type Modifier */ |
| u8 Vers; /* ISO, ECMA, & ANSI versions */ |
| u8 RDF; /* AEN, TRMIOP, & response data format */ |
| u8 AddLen; /* length of additional data */ |
| u8 Res1; /* reserved */ |
| u8 Res2; /* reserved */ |
| u8 Flags; /* RelADr, Wbus32, Wbus16, Sync, etc. */ |
| u8 VendorID[8]; /* Vendor Identification */ |
| u8 ProductID[16]; /* Product Identification */ |
| u8 ProductRev[4]; /* Product Revision */ |
| }; |
| |
| /* Inquiry byte 0 masks */ |
| #define SCSI_DEVTYPE 0x1F /* Peripheral Device Type */ |
| #define SCSI_PERIPHQUAL 0xE0 /* Peripheral Qualifier */ |
| /* Inquiry byte 1 mask */ |
| #define SCSI_REMOVABLE_MEDIA 0x80 /* Removable Media bit (1=removable) */ |
| /* Peripheral Device Type definitions */ |
| /* See include/scsi/scsi.h */ |
| #define TYPE_NODEV SCSI_DEVTYPE /* Unknown or no device type */ |
| #ifndef TYPE_PRINTER /* */ |
| # define TYPE_PRINTER 0x02 /* Printer device */ |
| #endif /* */ |
| #ifndef TYPE_COMM /* */ |
| # define TYPE_COMM 0x09 /* Communications device */ |
| #endif |
| |
| /************************************************************************/ |
| /* */ |
| /* Inquiry flag definitions (Inq data byte 7) */ |
| /* */ |
| /************************************************************************/ |
| #define SCSI_INQ_RELADR 0x80 /* device supports relative addressing */ |
| #define SCSI_INQ_WBUS32 0x40 /* device supports 32 bit data xfers */ |
| #define SCSI_INQ_WBUS16 0x20 /* device supports 16 bit data xfers */ |
| #define SCSI_INQ_SYNC 0x10 /* device supports synchronous xfer */ |
| #define SCSI_INQ_LINKED 0x08 /* device supports linked commands */ |
| #define SCSI_INQ_CMDQUEUE 0x02 /* device supports command queueing */ |
| #define SCSI_INQ_SFTRE 0x01 /* device supports soft resets */ |
| |
| #define ENABLE_CE 1 |
| #define DISABLE_CE 0 |
| #define EEPROM_READ 0x80 |
| |
| /************************************************************************/ |
| /* */ |
| /* The PCI configuration register offset for TRM_S1040 */ |
| /* */ |
| /************************************************************************/ |
| #define TRM_S1040_ID 0x00 /* Vendor and Device ID */ |
| #define TRM_S1040_COMMAND 0x04 /* PCI command register */ |
| #define TRM_S1040_IOBASE 0x10 /* I/O Space base address */ |
| #define TRM_S1040_ROMBASE 0x30 /* Expansion ROM Base Address */ |
| #define TRM_S1040_INTLINE 0x3C /* Interrupt line */ |
| |
| /************************************************************************/ |
| /* */ |
| /* The SCSI register offset for TRM_S1040 */ |
| /* */ |
| /************************************************************************/ |
| #define TRM_S1040_SCSI_STATUS 0x80 /* SCSI Status (R) */ |
| #define COMMANDPHASEDONE 0x2000 /* SCSI command phase done */ |
| #define SCSIXFERDONE 0x0800 /* SCSI SCSI transfer done */ |
| #define SCSIXFERCNT_2_ZERO 0x0100 /* SCSI SCSI transfer count to zero */ |
| #define SCSIINTERRUPT 0x0080 /* SCSI interrupt pending */ |
| #define COMMANDABORT 0x0040 /* SCSI command abort */ |
| #define SEQUENCERACTIVE 0x0020 /* SCSI sequencer active */ |
| #define PHASEMISMATCH 0x0010 /* SCSI phase mismatch */ |
| #define PARITYERROR 0x0008 /* SCSI parity error */ |
| |
| #define PHASEMASK 0x0007 /* Phase MSG/CD/IO */ |
| #define PH_DATA_OUT 0x00 /* Data out phase */ |
| #define PH_DATA_IN 0x01 /* Data in phase */ |
| #define PH_COMMAND 0x02 /* Command phase */ |
| #define PH_STATUS 0x03 /* Status phase */ |
| #define PH_BUS_FREE 0x05 /* Invalid phase used as bus free */ |
| #define PH_MSG_OUT 0x06 /* Message out phase */ |
| #define PH_MSG_IN 0x07 /* Message in phase */ |
| |
| #define TRM_S1040_SCSI_CONTROL 0x80 /* SCSI Control (W) */ |
| #define DO_CLRATN 0x0400 /* Clear ATN */ |
| #define DO_SETATN 0x0200 /* Set ATN */ |
| #define DO_CMDABORT 0x0100 /* Abort SCSI command */ |
| #define DO_RSTMODULE 0x0010 /* Reset SCSI chip */ |
| #define DO_RSTSCSI 0x0008 /* Reset SCSI bus */ |
| #define DO_CLRFIFO 0x0004 /* Clear SCSI transfer FIFO */ |
| #define DO_DATALATCH 0x0002 /* Enable SCSI bus data input (latched) */ |
| /* #define DO_DATALATCH 0x0000 */ /* KG: DISable SCSI bus data latch */ |
| #define DO_HWRESELECT 0x0001 /* Enable hardware reselection */ |
| |
| #define TRM_S1040_SCSI_FIFOCNT 0x82 /* SCSI FIFO Counter 5bits(R) */ |
| #define TRM_S1040_SCSI_SIGNAL 0x83 /* SCSI low level signal (R/W) */ |
| |
| #define TRM_S1040_SCSI_INTSTATUS 0x84 /* SCSI Interrupt Status (R) */ |
| #define INT_SCAM 0x80 /* SCAM selection interrupt */ |
| #define INT_SELECT 0x40 /* Selection interrupt */ |
| #define INT_SELTIMEOUT 0x20 /* Selection timeout interrupt */ |
| #define INT_DISCONNECT 0x10 /* Bus disconnected interrupt */ |
| #define INT_RESELECTED 0x08 /* Reselected interrupt */ |
| #define INT_SCSIRESET 0x04 /* SCSI reset detected interrupt */ |
| #define INT_BUSSERVICE 0x02 /* Bus service interrupt */ |
| #define INT_CMDDONE 0x01 /* SCSI command done interrupt */ |
| |
| #define TRM_S1040_SCSI_OFFSET 0x84 /* SCSI Offset Count (W) */ |
| |
| /************************************************************************/ |
| /* */ |
| /* Bit Name Definition */ |
| /* --------- ------------- ---------------------------- */ |
| /* 07-05 0 RSVD Reversed. Always 0. */ |
| /* 04 0 OFFSET4 Reversed for LVDS. Always 0. */ |
| /* 03-00 0 OFFSET[03:00] Offset number from 0 to 15 */ |
| /* */ |
| /************************************************************************/ |
| |
| #define TRM_S1040_SCSI_SYNC 0x85 /* SCSI Synchronous Control (R/W) */ |
| #define LVDS_SYNC 0x20 /* Enable LVDS synchronous */ |
| #define WIDE_SYNC 0x10 /* Enable WIDE synchronous */ |
| #define ALT_SYNC 0x08 /* Enable Fast-20 alternate synchronous */ |
| |
| /************************************************************************/ |
| /* */ |
| /* SYNCM 7 6 5 4 3 2 1 0 */ |
| /* Name RSVD RSVD LVDS WIDE ALTPERD PERIOD2 PERIOD1 PERIOD0 */ |
| /* Default 0 0 0 0 0 0 0 0 */ |
| /* */ |
| /* Bit Name Definition */ |
| /* --------- ------------- --------------------------- */ |
| /* 07-06 0 RSVD Reversed. Always read 0 */ |
| /* 05 0 LVDS Reversed. Always read 0 */ |
| /* 04 0 WIDE/WSCSI Enable wide (16-bits) SCSI */ |
| /* transfer. */ |
| /* 03 0 ALTPERD/ALTPD Alternate (Sync./Period) mode. */ |
| /* */ |
| /* @@ When this bit is set, */ |
| /* the synchronous period bits 2:0 */ |
| /* in the Synchronous Mode register */ |
| /* are used to transfer data */ |
| /* at the Fast-20 rate. */ |
| /* @@ When this bit is unset, */ |
| /* the synchronous period bits 2:0 */ |
| /* in the Synchronous Mode Register */ |
| /* are used to transfer data */ |
| /* at the Fast-10 rate (or Fast-40 w/ LVDS). */ |
| /* */ |
| /* 02-00 0 PERIOD[2:0]/ Synchronous SCSI Transfer Rate. */ |
| /* SXPD[02:00] These 3 bits specify */ |
| /* the Synchronous SCSI Transfer */ |
| /* Rate for Fast-20 and Fast-10. */ |
| /* These bits are also reset */ |
| /* by a SCSI Bus reset. */ |
| /* */ |
| /* For Fast-10 bit ALTPD = 0 and LVDS = 0 */ |
| /* and bit2,bit1,bit0 is defined as follows : */ |
| /* */ |
| /* 000 100ns, 10.0 MHz */ |
| /* 001 150ns, 6.6 MHz */ |
| /* 010 200ns, 5.0 MHz */ |
| /* 011 250ns, 4.0 MHz */ |
| /* 100 300ns, 3.3 MHz */ |
| /* 101 350ns, 2.8 MHz */ |
| /* 110 400ns, 2.5 MHz */ |
| /* 111 450ns, 2.2 MHz */ |
| /* */ |
| /* For Fast-20 bit ALTPD = 1 and LVDS = 0 */ |
| /* and bit2,bit1,bit0 is defined as follows : */ |
| /* */ |
| /* 000 50ns, 20.0 MHz */ |
| /* 001 75ns, 13.3 MHz */ |
| /* 010 100ns, 10.0 MHz */ |
| /* 011 125ns, 8.0 MHz */ |
| /* 100 150ns, 6.6 MHz */ |
| /* 101 175ns, 5.7 MHz */ |
| /* 110 200ns, 5.0 MHz */ |
| /* 111 250ns, 4.0 MHz KG: Maybe 225ns, 4.4 MHz */ |
| /* */ |
| /* For Fast-40 bit ALTPD = 0 and LVDS = 1 */ |
| /* and bit2,bit1,bit0 is defined as follows : */ |
| /* */ |
| /* 000 25ns, 40.0 MHz */ |
| /* 001 50ns, 20.0 MHz */ |
| /* 010 75ns, 13.3 MHz */ |
| /* 011 100ns, 10.0 MHz */ |
| /* 100 125ns, 8.0 MHz */ |
| /* 101 150ns, 6.6 MHz */ |
| /* 110 175ns, 5.7 MHz */ |
| /* 111 200ns, 5.0 MHz */ |
| /* */ |
| /************************************************************************/ |
| |
| #define TRM_S1040_SCSI_TARGETID 0x86 /* SCSI Target ID (R/W) */ |
| #define TRM_S1040_SCSI_IDMSG 0x87 /* SCSI Identify Message (R) */ |
| #define TRM_S1040_SCSI_HOSTID 0x87 /* SCSI Host ID (W) */ |
| #define TRM_S1040_SCSI_COUNTER 0x88 /* SCSI Transfer Counter 24bits(R/W) */ |
| |
| #define TRM_S1040_SCSI_INTEN 0x8C /* SCSI Interrupt Enable (R/W) */ |
| #define EN_SCAM 0x80 /* Enable SCAM selection interrupt */ |
| #define EN_SELECT 0x40 /* Enable selection interrupt */ |
| #define EN_SELTIMEOUT 0x20 /* Enable selection timeout interrupt */ |
| #define EN_DISCONNECT 0x10 /* Enable bus disconnected interrupt */ |
| #define EN_RESELECTED 0x08 /* Enable reselected interrupt */ |
| #define EN_SCSIRESET 0x04 /* Enable SCSI reset detected interrupt */ |
| #define EN_BUSSERVICE 0x02 /* Enable bus service interrupt */ |
| #define EN_CMDDONE 0x01 /* Enable SCSI command done interrupt */ |
| |
| #define TRM_S1040_SCSI_CONFIG0 0x8D /* SCSI Configuration 0 (R/W) */ |
| #define PHASELATCH 0x40 /* Enable phase latch */ |
| #define INITIATOR 0x20 /* Enable initiator mode */ |
| #define PARITYCHECK 0x10 /* Enable parity check */ |
| #define BLOCKRST 0x01 /* Disable SCSI reset1 */ |
| |
| #define TRM_S1040_SCSI_CONFIG1 0x8E /* SCSI Configuration 1 (R/W) */ |
| #define ACTIVE_NEGPLUS 0x10 /* Enhance active negation */ |
| #define FILTER_DISABLE 0x08 /* Disable SCSI data filter */ |
| #define FAST_FILTER 0x04 /* ? */ |
| #define ACTIVE_NEG 0x02 /* Enable active negation */ |
| |
| #define TRM_S1040_SCSI_CONFIG2 0x8F /* SCSI Configuration 2 (R/W) */ |
| #define CFG2_WIDEFIFO 0x02 /* */ |
| |
| #define TRM_S1040_SCSI_COMMAND 0x90 /* SCSI Command (R/W) */ |
| #define SCMD_COMP 0x12 /* Command complete */ |
| #define SCMD_SEL_ATN 0x60 /* Selection with ATN */ |
| #define SCMD_SEL_ATN3 0x64 /* Selection with ATN3 */ |
| #define SCMD_SEL_ATNSTOP 0xB8 /* Selection with ATN and Stop */ |
| #define SCMD_FIFO_OUT 0xC0 /* SCSI FIFO transfer out */ |
| #define SCMD_DMA_OUT 0xC1 /* SCSI DMA transfer out */ |
| #define SCMD_FIFO_IN 0xC2 /* SCSI FIFO transfer in */ |
| #define SCMD_DMA_IN 0xC3 /* SCSI DMA transfer in */ |
| #define SCMD_MSGACCEPT 0xD8 /* Message accept */ |
| |
| /************************************************************************/ |
| /* */ |
| /* Code Command Description */ |
| /* ---- ---------------------------------------- */ |
| /* 02 Enable reselection with FIFO */ |
| /* 40 Select without ATN with FIFO */ |
| /* 60 Select with ATN with FIFO */ |
| /* 64 Select with ATN3 with FIFO */ |
| /* A0 Select with ATN and stop with FIFO */ |
| /* C0 Transfer information out with FIFO */ |
| /* C1 Transfer information out with DMA */ |
| /* C2 Transfer information in with FIFO */ |
| /* C3 Transfer information in with DMA */ |
| /* 12 Initiator command complete with FIFO */ |
| /* 50 Initiator transfer information out sequence without ATN */ |
| /* with FIFO */ |
| /* 70 Initiator transfer information out sequence with ATN */ |
| /* with FIFO */ |
| /* 74 Initiator transfer information out sequence with ATN3 */ |
| /* with FIFO */ |
| /* 52 Initiator transfer information in sequence without ATN */ |
| /* with FIFO */ |
| /* 72 Initiator transfer information in sequence with ATN */ |
| /* with FIFO */ |
| /* 76 Initiator transfer information in sequence with ATN3 */ |
| /* with FIFO */ |
| /* 90 Initiator transfer information out command complete */ |
| /* with FIFO */ |
| /* 92 Initiator transfer information in command complete */ |
| /* with FIFO */ |
| /* D2 Enable selection */ |
| /* 08 Reselection */ |
| /* 48 Disconnect command with FIFO */ |
| /* 88 Terminate command with FIFO */ |
| /* C8 Target command complete with FIFO */ |
| /* 18 SCAM Arbitration/ Selection */ |
| /* 5A Enable reselection */ |
| /* 98 Select without ATN with FIFO */ |
| /* B8 Select with ATN with FIFO */ |
| /* D8 Message Accepted */ |
| /* 58 NOP */ |
| /* */ |
| /************************************************************************/ |
| |
| #define TRM_S1040_SCSI_TIMEOUT 0x91 /* SCSI Time Out Value (R/W) */ |
| #define TRM_S1040_SCSI_FIFO 0x98 /* SCSI FIFO (R/W) */ |
| |
| #define TRM_S1040_SCSI_TCR0 0x9C /* SCSI Target Control 0 (R/W) */ |
| #define TCR0_WIDE_NEGO_DONE 0x8000 /* Wide nego done */ |
| #define TCR0_SYNC_NEGO_DONE 0x4000 /* Synchronous nego done */ |
| #define TCR0_ENABLE_LVDS 0x2000 /* Enable LVDS synchronous */ |
| #define TCR0_ENABLE_WIDE 0x1000 /* Enable WIDE synchronous */ |
| #define TCR0_ENABLE_ALT 0x0800 /* Enable alternate synchronous */ |
| #define TCR0_PERIOD_MASK 0x0700 /* Transfer rate */ |
| |
| #define TCR0_DO_WIDE_NEGO 0x0080 /* Do wide NEGO */ |
| #define TCR0_DO_SYNC_NEGO 0x0040 /* Do sync NEGO */ |
| #define TCR0_DISCONNECT_EN 0x0020 /* Disconnection enable */ |
| #define TCR0_OFFSET_MASK 0x001F /* Offset number */ |
| |
| #define TRM_S1040_SCSI_TCR1 0x9E /* SCSI Target Control 1 (R/W) */ |
| #define MAXTAG_MASK 0x7F00 /* Maximum tags (127) */ |
| #define NON_TAG_BUSY 0x0080 /* Non tag command active */ |
| #define ACTTAG_MASK 0x007F /* Active tags */ |
| |
| /************************************************************************/ |
| /* */ |
| /* The DMA register offset for TRM_S1040 */ |
| /* */ |
| /************************************************************************/ |
| #define TRM_S1040_DMA_COMMAND 0xA0 /* DMA Command (R/W) */ |
| #define DMACMD_SG 0x02 /* Enable HW S/G support */ |
| #define DMACMD_DIR 0x01 /* 1 = read from SCSI write to Host */ |
| #define XFERDATAIN_SG 0x0103 /* Transfer data in w/ SG */ |
| #define XFERDATAOUT_SG 0x0102 /* Transfer data out w/ SG */ |
| #define XFERDATAIN 0x0101 /* Transfer data in w/o SG */ |
| #define XFERDATAOUT 0x0100 /* Transfer data out w/o SG */ |
| |
| #define TRM_S1040_DMA_FIFOCNT 0xA1 /* DMA FIFO Counter (R) */ |
| |
| #define TRM_S1040_DMA_CONTROL 0xA1 /* DMA Control (W) */ |
| #define DMARESETMODULE 0x10 /* Reset PCI/DMA module */ |
| #define STOPDMAXFER 0x08 /* Stop DMA transfer */ |
| #define ABORTXFER 0x04 /* Abort DMA transfer */ |
| #define CLRXFIFO 0x02 /* Clear DMA transfer FIFO */ |
| #define STARTDMAXFER 0x01 /* Start DMA transfer */ |
| |
| #define TRM_S1040_DMA_FIFOSTAT 0xA2 /* DMA FIFO Status (R) */ |
| |
| #define TRM_S1040_DMA_STATUS 0xA3 /* DMA Interrupt Status (R/W) */ |
| #define XFERPENDING 0x80 /* Transfer pending */ |
| #define SCSIBUSY 0x40 /* SCSI busy */ |
| #define GLOBALINT 0x20 /* DMA_INTEN bit 0-4 set */ |
| #define FORCEDMACOMP 0x10 /* Force DMA transfer complete */ |
| #define DMAXFERERROR 0x08 /* DMA transfer error */ |
| #define DMAXFERABORT 0x04 /* DMA transfer abort */ |
| #define DMAXFERCOMP 0x02 /* Bus Master XFER Complete status */ |
| #define SCSICOMP 0x01 /* SCSI complete interrupt */ |
| |
| #define TRM_S1040_DMA_INTEN 0xA4 /* DMA Interrupt Enable (R/W) */ |
| #define EN_FORCEDMACOMP 0x10 /* Force DMA transfer complete */ |
| #define EN_DMAXFERERROR 0x08 /* DMA transfer error */ |
| #define EN_DMAXFERABORT 0x04 /* DMA transfer abort */ |
| #define EN_DMAXFERCOMP 0x02 /* Bus Master XFER Complete status */ |
| #define EN_SCSIINTR 0x01 /* Enable SCSI complete interrupt */ |
| |
| #define TRM_S1040_DMA_CONFIG 0xA6 /* DMA Configuration (R/W) */ |
| #define DMA_ENHANCE 0x8000 /* Enable DMA enhance feature (SG?) */ |
| #define DMA_PCI_DUAL_ADDR 0x4000 /* */ |
| #define DMA_CFG_RES 0x2000 /* Always 1 */ |
| #define DMA_AUTO_CLR_FIFO 0x1000 /* DISable DMA auto clear FIFO */ |
| #define DMA_MEM_MULTI_READ 0x0800 /* */ |
| #define DMA_MEM_WRITE_INVAL 0x0400 /* Memory write and invalidate */ |
| #define DMA_FIFO_CTRL 0x0300 /* Control FIFO operation with DMA */ |
| #define DMA_FIFO_HALF_HALF 0x0200 /* Keep half filled on both read/write */ |
| |
| #define TRM_S1040_DMA_XCNT 0xA8 /* DMA Transfer Counter (R/W), 24bits */ |
| #define TRM_S1040_DMA_CXCNT 0xAC /* DMA Current Transfer Counter (R) */ |
| #define TRM_S1040_DMA_XLOWADDR 0xB0 /* DMA Transfer Physical Low Address */ |
| #define TRM_S1040_DMA_XHIGHADDR 0xB4 /* DMA Transfer Physical High Address */ |
| |
| /************************************************************************/ |
| /* */ |
| /* The general register offset for TRM_S1040 */ |
| /* */ |
| /************************************************************************/ |
| #define TRM_S1040_GEN_CONTROL 0xD4 /* Global Control */ |
| #define CTRL_LED 0x80 /* Control onboard LED */ |
| #define EN_EEPROM 0x10 /* Enable EEPROM programming */ |
| #define DIS_TERM 0x08 /* Disable onboard termination */ |
| #define AUTOTERM 0x04 /* Enable Auto SCSI terminator */ |
| #define LOW8TERM 0x02 /* Enable Lower 8 bit SCSI terminator */ |
| #define UP8TERM 0x01 /* Enable Upper 8 bit SCSI terminator */ |
| |
| #define TRM_S1040_GEN_STATUS 0xD5 /* Global Status */ |
| #define GTIMEOUT 0x80 /* Global timer reach 0 */ |
| #define EXT68HIGH 0x40 /* Higher 8 bit connected externally */ |
| #define INT68HIGH 0x20 /* Higher 8 bit connected internally */ |
| #define CON5068 0x10 /* External 50/68 pin connected (low) */ |
| #define CON68 0x08 /* Internal 68 pin connected (low) */ |
| #define CON50 0x04 /* Internal 50 pin connected (low!) */ |
| #define WIDESCSI 0x02 /* Wide SCSI card */ |
| #define STATUS_LOAD_DEFAULT 0x01 /* */ |
| |
| #define TRM_S1040_GEN_NVRAM 0xD6 /* Serial NON-VOLATILE RAM port */ |
| #define NVR_BITOUT 0x08 /* Serial data out */ |
| #define NVR_BITIN 0x04 /* Serial data in */ |
| #define NVR_CLOCK 0x02 /* Serial clock */ |
| #define NVR_SELECT 0x01 /* Serial select */ |
| |
| #define TRM_S1040_GEN_EDATA 0xD7 /* Parallel EEPROM data port */ |
| #define TRM_S1040_GEN_EADDRESS 0xD8 /* Parallel EEPROM address */ |
| #define TRM_S1040_GEN_TIMER 0xDB /* Global timer */ |
| |
| /************************************************************************/ |
| /* */ |
| /* NvmTarCfg0: Target configuration byte 0 :..pDCB->DevMode */ |
| /* */ |
| /************************************************************************/ |
| #define NTC_DO_WIDE_NEGO 0x20 /* Wide negotiate */ |
| #define NTC_DO_TAG_QUEUEING 0x10 /* Enable SCSI tag queuing */ |
| #define NTC_DO_SEND_START 0x08 /* Send start command SPINUP */ |
| #define NTC_DO_DISCONNECT 0x04 /* Enable SCSI disconnect */ |
| #define NTC_DO_SYNC_NEGO 0x02 /* Sync negotiation */ |
| #define NTC_DO_PARITY_CHK 0x01 /* (it sould define at NAC) */ |
| /* Parity check enable */ |
| |
| /************************************************************************/ |
| /* */ |
| /* Nvram Initiater bits definition */ |
| /* */ |
| /************************************************************************/ |
| #if 0 |
| #define MORE2_DRV BIT0 |
| #define GREATER_1G BIT1 |
| #define RST_SCSI_BUS BIT2 |
| #define ACTIVE_NEGATION BIT3 |
| #define NO_SEEK BIT4 |
| #define LUN_CHECK BIT5 |
| #endif |
| |
| /************************************************************************/ |
| /* */ |
| /* Nvram Adapter Cfg bits definition */ |
| /* */ |
| /************************************************************************/ |
| #define NAC_SCANLUN 0x20 /* Include LUN as BIOS device */ |
| #define NAC_POWERON_SCSI_RESET 0x04 /* Power on reset enable */ |
| #define NAC_GREATER_1G 0x02 /* > 1G support enable */ |
| #define NAC_GT2DRIVES 0x01 /* Support more than 2 drives */ |
| /* #define NAC_DO_PARITY_CHK 0x08 */ /* Parity check enable */ |
| |
| #endif |