sky2: flow control negotiation for Yukon-FE
The Yukon-FE chip doesn't do gigabit and has a differen PHY internally.
On this chip, phy status register doesn't properly reflect the result
of flow control negotiation. To workaround the problem and avoid having
to have so much chip dependent code; compute the result of flow control
by looking at the local and remote advertised bits.
Signed-off-by: Stephen Hemmminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c
index e567996..2c91181 100644
--- a/drivers/net/sky2.c
+++ b/drivers/net/sky2.c
@@ -1766,10 +1766,10 @@
{
struct sky2_hw *hw = sky2->hw;
unsigned port = sky2->port;
- u16 lpa;
+ u16 advert, lpa;
+ advert = gm_phy_read(hw, port, PHY_MARV_AUNE_ADV);
lpa = gm_phy_read(hw, port, PHY_MARV_AUNE_LP);
-
if (lpa & PHY_M_AN_RF) {
printk(KERN_ERR PFX "%s: remote fault", sky2->netdev->name);
return -1;
@@ -1784,20 +1784,40 @@
sky2->speed = sky2_phy_speed(hw, aux);
sky2->duplex = (aux & PHY_M_PS_FULL_DUP) ? DUPLEX_FULL : DUPLEX_HALF;
- /* Pause bits are offset (9..8) */
- if (hw->chip_id == CHIP_ID_YUKON_XL
- || hw->chip_id == CHIP_ID_YUKON_EC_U
- || hw->chip_id == CHIP_ID_YUKON_EX)
- aux >>= 6;
+ /* Since the pause result bits seem to in different positions on
+ * different chips. look at registers.
+ */
+ if (!sky2_is_copper(hw)) {
+ /* Shift for bits in fiber PHY */
+ advert &= ~(ADVERTISE_PAUSE_CAP|ADVERTISE_PAUSE_ASYM);
+ lpa &= ~(LPA_PAUSE_CAP|LPA_PAUSE_ASYM);
- sky2->flow_status = sky2_flow(aux & PHY_M_PS_RX_P_EN,
- aux & PHY_M_PS_TX_P_EN);
+ if (advert & ADVERTISE_1000XPAUSE)
+ advert |= ADVERTISE_PAUSE_CAP;
+ if (advert & ADVERTISE_1000XPSE_ASYM)
+ advert |= ADVERTISE_PAUSE_ASYM;
+ if (lpa & LPA_1000XPAUSE)
+ lpa |= LPA_PAUSE_CAP;
+ if (lpa & LPA_1000XPAUSE_ASYM)
+ lpa |= LPA_PAUSE_ASYM;
+ }
+
+ sky2->flow_status = FC_NONE;
+ if (advert & ADVERTISE_PAUSE_CAP) {
+ if (lpa & LPA_PAUSE_CAP)
+ sky2->flow_status = FC_BOTH;
+ else if (advert & ADVERTISE_PAUSE_ASYM)
+ sky2->flow_status = FC_RX;
+ } else if (advert & ADVERTISE_PAUSE_ASYM) {
+ if ((lpa & LPA_PAUSE_CAP) && (lpa & LPA_PAUSE_ASYM))
+ sky2->flow_status = FC_TX;
+ }
if (sky2->duplex == DUPLEX_HALF && sky2->speed < SPEED_1000
&& !(hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX))
sky2->flow_status = FC_NONE;
- if (aux & PHY_M_PS_RX_P_EN)
+ if (sky2->flow_status & FC_TX)
sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_ON);
else
sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);