ARM: S5PV210: Use generic DMA PL330 driver
This patch makes Samsung S5PV210 to use DMA PL330 driver
on DMADEVICE. The S5PV210 uses DMA generic APIs instead of
SAMSUNG specific S3C-PL330 APIs.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
diff --git a/arch/arm/mach-s5pv210/Kconfig b/arch/arm/mach-s5pv210/Kconfig
index 69dd87c..d960090 100644
--- a/arch/arm/mach-s5pv210/Kconfig
+++ b/arch/arm/mach-s5pv210/Kconfig
@@ -11,7 +11,7 @@
config CPU_S5PV210
bool
- select S3C_PL330_DMA
+ select SAMSUNG_DMADEV
select S5P_EXT_INT
select S5P_HRT
select S5PV210_PM if PM
diff --git a/arch/arm/mach-s5pv210/clock.c b/arch/arm/mach-s5pv210/clock.c
index 52a8e60..d35726a 100644
--- a/arch/arm/mach-s5pv210/clock.c
+++ b/arch/arm/mach-s5pv210/clock.c
@@ -203,6 +203,11 @@
.name = "pcmcdclk",
};
+static struct clk dummy_apb_pclk = {
+ .name = "apb_pclk",
+ .id = -1,
+};
+
static struct clk *clkset_vpllsrc_list[] = {
[0] = &clk_fin_vpll,
[1] = &clk_sclk_hdmi27m,
@@ -289,13 +294,13 @@
static struct clk init_clocks_off[] = {
{
- .name = "pdma",
+ .name = "dma",
.devname = "s3c-pl330.0",
.parent = &clk_hclk_psys.clk,
.enable = s5pv210_clk_ip0_ctrl,
.ctrlbit = (1 << 3),
}, {
- .name = "pdma",
+ .name = "dma",
.devname = "s3c-pl330.1",
.parent = &clk_hclk_psys.clk,
.enable = s5pv210_clk_ip0_ctrl,
@@ -1161,5 +1166,6 @@
s3c_register_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
s3c_disable_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
+ s3c24xx_register_clock(&dummy_apb_pclk);
s3c_pwmclk_init();
}
diff --git a/arch/arm/mach-s5pv210/dma.c b/arch/arm/mach-s5pv210/dma.c
index 497d343..f79d0b0 100644
--- a/arch/arm/mach-s5pv210/dma.c
+++ b/arch/arm/mach-s5pv210/dma.c
@@ -1,4 +1,8 @@
-/*
+/* linux/arch/arm/mach-s5pv210/dma.c
+ *
+ * Copyright (c) 2011 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ *
* Copyright (C) 2010 Samsung Electronics Co. Ltd.
* Jaswinder Singh <jassi.brar@samsung.com>
*
@@ -17,151 +21,239 @@
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
-#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
+#include <linux/amba/bus.h>
+#include <linux/amba/pl330.h>
+#include <asm/irq.h>
#include <plat/devs.h>
#include <plat/irqs.h>
#include <mach/map.h>
#include <mach/irqs.h>
-
-#include <plat/s3c-pl330-pdata.h>
+#include <mach/dma.h>
static u64 dma_dmamask = DMA_BIT_MASK(32);
-static struct resource s5pv210_pdma0_resource[] = {
- [0] = {
- .start = S5PV210_PA_PDMA0,
- .end = S5PV210_PA_PDMA0 + SZ_4K,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = IRQ_PDMA0,
- .end = IRQ_PDMA0,
- .flags = IORESOURCE_IRQ,
+struct dma_pl330_peri pdma0_peri[28] = {
+ {
+ .peri_id = (u8)DMACH_UART0_RX,
+ .rqtype = DEVTOMEM,
+ }, {
+ .peri_id = (u8)DMACH_UART0_TX,
+ .rqtype = MEMTODEV,
+ }, {
+ .peri_id = (u8)DMACH_UART1_RX,
+ .rqtype = DEVTOMEM,
+ }, {
+ .peri_id = (u8)DMACH_UART1_TX,
+ .rqtype = MEMTODEV,
+ }, {
+ .peri_id = (u8)DMACH_UART2_RX,
+ .rqtype = DEVTOMEM,
+ }, {
+ .peri_id = (u8)DMACH_UART2_TX,
+ .rqtype = MEMTODEV,
+ }, {
+ .peri_id = (u8)DMACH_UART3_RX,
+ .rqtype = DEVTOMEM,
+ }, {
+ .peri_id = (u8)DMACH_UART3_TX,
+ .rqtype = MEMTODEV,
+ }, {
+ .peri_id = DMACH_MAX,
+ }, {
+ .peri_id = (u8)DMACH_I2S0_RX,
+ .rqtype = DEVTOMEM,
+ }, {
+ .peri_id = (u8)DMACH_I2S0_TX,
+ .rqtype = MEMTODEV,
+ }, {
+ .peri_id = (u8)DMACH_I2S0S_TX,
+ .rqtype = MEMTODEV,
+ }, {
+ .peri_id = (u8)DMACH_I2S1_RX,
+ .rqtype = DEVTOMEM,
+ }, {
+ .peri_id = (u8)DMACH_I2S1_TX,
+ .rqtype = MEMTODEV,
+ }, {
+ .peri_id = (u8)DMACH_MAX,
+ }, {
+ .peri_id = (u8)DMACH_MAX,
+ }, {
+ .peri_id = (u8)DMACH_SPI0_RX,
+ .rqtype = DEVTOMEM,
+ }, {
+ .peri_id = (u8)DMACH_SPI0_TX,
+ .rqtype = MEMTODEV,
+ }, {
+ .peri_id = (u8)DMACH_SPI1_RX,
+ .rqtype = DEVTOMEM,
+ }, {
+ .peri_id = (u8)DMACH_SPI1_TX,
+ .rqtype = MEMTODEV,
+ }, {
+ .peri_id = (u8)DMACH_MAX,
+ }, {
+ .peri_id = (u8)DMACH_MAX,
+ }, {
+ .peri_id = (u8)DMACH_AC97_MICIN,
+ .rqtype = DEVTOMEM,
+ }, {
+ .peri_id = (u8)DMACH_AC97_PCMIN,
+ .rqtype = DEVTOMEM,
+ }, {
+ .peri_id = (u8)DMACH_AC97_PCMOUT,
+ .rqtype = MEMTODEV,
+ }, {
+ .peri_id = (u8)DMACH_MAX,
+ }, {
+ .peri_id = (u8)DMACH_PWM,
+ }, {
+ .peri_id = (u8)DMACH_SPDIF,
+ .rqtype = MEMTODEV,
},
};
-static struct s3c_pl330_platdata s5pv210_pdma0_pdata = {
- .peri = {
- [0] = DMACH_UART0_RX,
- [1] = DMACH_UART0_TX,
- [2] = DMACH_UART1_RX,
- [3] = DMACH_UART1_TX,
- [4] = DMACH_UART2_RX,
- [5] = DMACH_UART2_TX,
- [6] = DMACH_UART3_RX,
- [7] = DMACH_UART3_TX,
- [8] = DMACH_MAX,
- [9] = DMACH_I2S0_RX,
- [10] = DMACH_I2S0_TX,
- [11] = DMACH_I2S0S_TX,
- [12] = DMACH_I2S1_RX,
- [13] = DMACH_I2S1_TX,
- [14] = DMACH_MAX,
- [15] = DMACH_MAX,
- [16] = DMACH_SPI0_RX,
- [17] = DMACH_SPI0_TX,
- [18] = DMACH_SPI1_RX,
- [19] = DMACH_SPI1_TX,
- [20] = DMACH_MAX,
- [21] = DMACH_MAX,
- [22] = DMACH_AC97_MICIN,
- [23] = DMACH_AC97_PCMIN,
- [24] = DMACH_AC97_PCMOUT,
- [25] = DMACH_MAX,
- [26] = DMACH_PWM,
- [27] = DMACH_SPDIF,
- [28] = DMACH_MAX,
- [29] = DMACH_MAX,
- [30] = DMACH_MAX,
- [31] = DMACH_MAX,
- },
+struct dma_pl330_platdata s5pv210_pdma0_pdata = {
+ .nr_valid_peri = ARRAY_SIZE(pdma0_peri),
+ .peri = pdma0_peri,
};
-static struct platform_device s5pv210_device_pdma0 = {
- .name = "s3c-pl330",
- .id = 0,
- .num_resources = ARRAY_SIZE(s5pv210_pdma0_resource),
- .resource = s5pv210_pdma0_resource,
- .dev = {
+struct amba_device s5pv210_device_pdma0 = {
+ .dev = {
+ .init_name = "dma-pl330.0",
.dma_mask = &dma_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
.platform_data = &s5pv210_pdma0_pdata,
},
-};
-
-static struct resource s5pv210_pdma1_resource[] = {
- [0] = {
- .start = S5PV210_PA_PDMA1,
- .end = S5PV210_PA_PDMA1 + SZ_4K,
+ .res = {
+ .start = S5PV210_PA_PDMA0,
+ .end = S5PV210_PA_PDMA0 + SZ_4K,
.flags = IORESOURCE_MEM,
},
- [1] = {
- .start = IRQ_PDMA1,
- .end = IRQ_PDMA1,
- .flags = IORESOURCE_IRQ,
+ .irq = {IRQ_PDMA0, NO_IRQ},
+ .periphid = 0x00041330,
+};
+
+struct dma_pl330_peri pdma1_peri[32] = {
+ {
+ .peri_id = (u8)DMACH_UART0_RX,
+ .rqtype = DEVTOMEM,
+ }, {
+ .peri_id = (u8)DMACH_UART0_TX,
+ .rqtype = MEMTODEV,
+ }, {
+ .peri_id = (u8)DMACH_UART1_RX,
+ .rqtype = DEVTOMEM,
+ }, {
+ .peri_id = (u8)DMACH_UART1_TX,
+ .rqtype = MEMTODEV,
+ }, {
+ .peri_id = (u8)DMACH_UART2_RX,
+ .rqtype = DEVTOMEM,
+ }, {
+ .peri_id = (u8)DMACH_UART2_TX,
+ .rqtype = MEMTODEV,
+ }, {
+ .peri_id = (u8)DMACH_UART3_RX,
+ .rqtype = DEVTOMEM,
+ }, {
+ .peri_id = (u8)DMACH_UART3_TX,
+ .rqtype = MEMTODEV,
+ }, {
+ .peri_id = DMACH_MAX,
+ }, {
+ .peri_id = (u8)DMACH_I2S0_RX,
+ .rqtype = DEVTOMEM,
+ }, {
+ .peri_id = (u8)DMACH_I2S0_TX,
+ .rqtype = MEMTODEV,
+ }, {
+ .peri_id = (u8)DMACH_I2S0S_TX,
+ .rqtype = MEMTODEV,
+ }, {
+ .peri_id = (u8)DMACH_I2S1_RX,
+ .rqtype = DEVTOMEM,
+ }, {
+ .peri_id = (u8)DMACH_I2S1_TX,
+ .rqtype = MEMTODEV,
+ }, {
+ .peri_id = (u8)DMACH_I2S2_RX,
+ .rqtype = DEVTOMEM,
+ }, {
+ .peri_id = (u8)DMACH_I2S2_TX,
+ .rqtype = MEMTODEV,
+ }, {
+ .peri_id = (u8)DMACH_SPI0_RX,
+ .rqtype = DEVTOMEM,
+ }, {
+ .peri_id = (u8)DMACH_SPI0_TX,
+ .rqtype = MEMTODEV,
+ }, {
+ .peri_id = (u8)DMACH_SPI1_RX,
+ .rqtype = DEVTOMEM,
+ }, {
+ .peri_id = (u8)DMACH_SPI1_TX,
+ .rqtype = MEMTODEV,
+ }, {
+ .peri_id = (u8)DMACH_MAX,
+ }, {
+ .peri_id = (u8)DMACH_MAX,
+ }, {
+ .peri_id = (u8)DMACH_PCM0_RX,
+ .rqtype = DEVTOMEM,
+ }, {
+ .peri_id = (u8)DMACH_PCM0_TX,
+ .rqtype = MEMTODEV,
+ }, {
+ .peri_id = (u8)DMACH_PCM1_RX,
+ .rqtype = DEVTOMEM,
+ }, {
+ .peri_id = (u8)DMACH_PCM1_TX,
+ .rqtype = MEMTODEV,
+ }, {
+ .peri_id = (u8)DMACH_MSM_REQ0,
+ }, {
+ .peri_id = (u8)DMACH_MSM_REQ1,
+ }, {
+ .peri_id = (u8)DMACH_MSM_REQ2,
+ }, {
+ .peri_id = (u8)DMACH_MSM_REQ3,
+ }, {
+ .peri_id = (u8)DMACH_PCM2_RX,
+ .rqtype = DEVTOMEM,
+ }, {
+ .peri_id = (u8)DMACH_PCM2_TX,
+ .rqtype = MEMTODEV,
},
};
-static struct s3c_pl330_platdata s5pv210_pdma1_pdata = {
- .peri = {
- [0] = DMACH_UART0_RX,
- [1] = DMACH_UART0_TX,
- [2] = DMACH_UART1_RX,
- [3] = DMACH_UART1_TX,
- [4] = DMACH_UART2_RX,
- [5] = DMACH_UART2_TX,
- [6] = DMACH_UART3_RX,
- [7] = DMACH_UART3_TX,
- [8] = DMACH_MAX,
- [9] = DMACH_I2S0_RX,
- [10] = DMACH_I2S0_TX,
- [11] = DMACH_I2S0S_TX,
- [12] = DMACH_I2S1_RX,
- [13] = DMACH_I2S1_TX,
- [14] = DMACH_I2S2_RX,
- [15] = DMACH_I2S2_TX,
- [16] = DMACH_SPI0_RX,
- [17] = DMACH_SPI0_TX,
- [18] = DMACH_SPI1_RX,
- [19] = DMACH_SPI1_TX,
- [20] = DMACH_MAX,
- [21] = DMACH_MAX,
- [22] = DMACH_PCM0_RX,
- [23] = DMACH_PCM0_TX,
- [24] = DMACH_PCM1_RX,
- [25] = DMACH_PCM1_TX,
- [26] = DMACH_MSM_REQ0,
- [27] = DMACH_MSM_REQ1,
- [28] = DMACH_MSM_REQ2,
- [29] = DMACH_MSM_REQ3,
- [30] = DMACH_PCM2_RX,
- [31] = DMACH_PCM2_TX,
- },
+struct dma_pl330_platdata s5pv210_pdma1_pdata = {
+ .nr_valid_peri = ARRAY_SIZE(pdma1_peri),
+ .peri = pdma1_peri,
};
-static struct platform_device s5pv210_device_pdma1 = {
- .name = "s3c-pl330",
- .id = 1,
- .num_resources = ARRAY_SIZE(s5pv210_pdma1_resource),
- .resource = s5pv210_pdma1_resource,
- .dev = {
+struct amba_device s5pv210_device_pdma1 = {
+ .dev = {
+ .init_name = "dma-pl330.1",
.dma_mask = &dma_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
.platform_data = &s5pv210_pdma1_pdata,
},
-};
-
-static struct platform_device *s5pv210_dmacs[] __initdata = {
- &s5pv210_device_pdma0,
- &s5pv210_device_pdma1,
+ .res = {
+ .start = S5PV210_PA_PDMA1,
+ .end = S5PV210_PA_PDMA1 + SZ_4K,
+ .flags = IORESOURCE_MEM,
+ },
+ .irq = {IRQ_PDMA1, NO_IRQ},
+ .periphid = 0x00041330,
};
static int __init s5pv210_dma_init(void)
{
- platform_add_devices(s5pv210_dmacs, ARRAY_SIZE(s5pv210_dmacs));
+ amba_device_register(&s5pv210_device_pdma0, &iomem_resource);
return 0;
}
diff --git a/arch/arm/mach-s5pv210/include/mach/dma.h b/arch/arm/mach-s5pv210/include/mach/dma.h
index 1beae2c..201842a 100644
--- a/arch/arm/mach-s5pv210/include/mach/dma.h
+++ b/arch/arm/mach-s5pv210/include/mach/dma.h
@@ -20,7 +20,7 @@
#ifndef __MACH_DMA_H
#define __MACH_DMA_H
-/* This platform uses the common S3C DMA API driver for PL330 */
+/* This platform uses the common DMA API driver for PL330 */
#include <plat/dma-pl330.h>
#endif /* __MACH_DMA_H */