ab8500-bm: Add usb power path support
AB8540 supports power path function in USB charging mode for fast
power up with dead and weak battery, and it could extend
the battery age.
When USB charging starts, if the Vbattrue is below than SW cut off
voltage, power path and pre-charge should be enabled. If Vbattrue
is higher than SW cut off voltage, power path and pre-charge should
be disabled. This is to make sure full current to battery charge.
At the end of charge, power path should be enable again to reduce
charging the battery again.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
diff --git a/drivers/power/abx500_chargalg.c b/drivers/power/abx500_chargalg.c
index a876976..a9b8efd 100644
--- a/drivers/power/abx500_chargalg.c
+++ b/drivers/power/abx500_chargalg.c
@@ -34,6 +34,9 @@
/* End-of-charge criteria counter */
#define EOC_COND_CNT 10
+/* Plus margin for the low battery threshold */
+#define BAT_PLUS_MARGIN (100)
+
#define to_abx500_chargalg_device_info(x) container_of((x), \
struct abx500_chargalg, chargalg_psy);
@@ -83,6 +86,7 @@
STATE_HW_TEMP_PROTECT_INIT,
STATE_HW_TEMP_PROTECT,
STATE_NORMAL_INIT,
+ STATE_USB_PP_PRE_CHARGE,
STATE_NORMAL,
STATE_WAIT_FOR_RECHARGE_INIT,
STATE_WAIT_FOR_RECHARGE,
@@ -114,6 +118,7 @@
"HW_TEMP_PROTECT_INIT",
"HW_TEMP_PROTECT",
"NORMAL_INIT",
+ "USB_PP_PRE_CHARGE",
"NORMAL",
"WAIT_FOR_RECHARGE_INIT",
"WAIT_FOR_RECHARGE",
@@ -560,6 +565,37 @@
return di->usb_chg->ops.enable(di->usb_chg, enable, vset, iset);
}
+ /**
+ * ab8540_chargalg_usb_pp_en() - Enable/ disable USB power path
+ * @di: pointer to the abx500_chargalg structure
+ * @enable: power path enable/disable
+ *
+ * The USB power path will be enable/ disable
+ */
+static int ab8540_chargalg_usb_pp_en(struct abx500_chargalg *di, bool enable)
+{
+ if (!di->usb_chg || !di->usb_chg->ops.pp_enable)
+ return -ENXIO;
+
+ return di->usb_chg->ops.pp_enable(di->usb_chg, enable);
+}
+
+/**
+ * ab8540_chargalg_usb_pre_chg_en() - Enable/ disable USB pre-charge
+ * @di: pointer to the abx500_chargalg structure
+ * @enable: USB pre-charge enable/disable
+ *
+ * The USB USB pre-charge will be enable/ disable
+ */
+static int ab8540_chargalg_usb_pre_chg_en(struct abx500_chargalg *di,
+ bool enable)
+{
+ if (!di->usb_chg || !di->usb_chg->ops.pre_chg_enable)
+ return -ENXIO;
+
+ return di->usb_chg->ops.pre_chg_enable(di->usb_chg, enable);
+}
+
/**
* abx500_chargalg_update_chg_curr() - Update charger current
* @di: pointer to the abx500_chargalg structure
@@ -765,6 +801,9 @@
di->batt_data.avg_curr > 0) {
if (++di->eoc_cnt >= EOC_COND_CNT) {
di->eoc_cnt = 0;
+ if ((di->chg_info.charger_type & USB_CHG) &&
+ (di->usb_chg->power_path))
+ ab8540_chargalg_usb_pp_en(di, true);
di->charge_status = POWER_SUPPLY_STATUS_FULL;
di->maintenance_chg = true;
dev_dbg(di->dev, "EOC reached!\n");
@@ -1465,6 +1504,22 @@
break;
case STATE_NORMAL_INIT:
+ if ((di->chg_info.charger_type & USB_CHG) &&
+ di->usb_chg->power_path) {
+ if (di->batt_data.volt >
+ (di->bm->fg_params->lowbat_threshold +
+ BAT_PLUS_MARGIN)) {
+ ab8540_chargalg_usb_pre_chg_en(di, false);
+ ab8540_chargalg_usb_pp_en(di, false);
+ } else {
+ ab8540_chargalg_usb_pp_en(di, true);
+ ab8540_chargalg_usb_pre_chg_en(di, true);
+ abx500_chargalg_state_to(di,
+ STATE_USB_PP_PRE_CHARGE);
+ break;
+ }
+ }
+
abx500_chargalg_start_charging(di,
di->bm->bat_type[di->bm->batt_id].normal_vol_lvl,
di->bm->bat_type[di->bm->batt_id].normal_cur_lvl);
@@ -1479,6 +1534,13 @@
break;
+ case STATE_USB_PP_PRE_CHARGE:
+ if (di->batt_data.volt >
+ (di->bm->fg_params->lowbat_threshold +
+ BAT_PLUS_MARGIN))
+ abx500_chargalg_state_to(di, STATE_NORMAL_INIT);
+ break;
+
case STATE_NORMAL:
handle_maxim_chg_curr(di);
if (di->charge_status == POWER_SUPPLY_STATUS_FULL &&