ARM: dts: Add device tree support for phycard pca100
Board files for Phytec phyCARD-S "System on Module" and "Rapid
Development Kit".
Based on patches from:
Steffen Trumtrar <s.trumtrar@pengutronix.de>:
- Original patch
- ARM: dts: Set partition offsets for phycard
- ARM: dts: Use CSPI1 instead of CSPI2 on phycard pca100
- ARM: imx27-phytec-phycard-S.dts: resize nand partitions
Jan Luebbe <jlu@pengutronix.de>:
- ARM: dts: Enable bad block table in NAND
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
diff --git a/arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts b/arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts
new file mode 100644
index 0000000..390d8f2
--- /dev/null
+++ b/arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts
@@ -0,0 +1,62 @@
+/*
+ * Copyright 2012 Markus Pargmann, Pengutronix
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include "imx27-phytec-phycard-s-som.dts"
+
+/ {
+ model = "Phytec pca100 rapid development kit";
+ compatible = "phytec,imx27-pca100-rdk", "phytec,imx27-pca100", "fsl,imx27";
+
+ display: display {
+ model = "Primeview-PD050VL1";
+ native-mode = <&timing0>;
+ bits-per-pixel = <16>; /* non-standard but required */
+ fsl,pcr = <0xf0c88080>; /* non-standard but required */
+ display-timings {
+ timing0: 640x480 {
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <112>;
+ hfront-porch = <36>;
+ hsync-len = <32>;
+ vback-porch = <33>;
+ vfront-porch = <33>;
+ vsync-len = <2>;
+ clock-frequency = <25000000>;
+ };
+ };
+ };
+};
+
+&fb {
+ display = <&display>;
+ status = "okay";
+};
+
+&sdhci2 {
+ cd-gpios = <&gpio3 29 0>;
+ status = "okay";
+};
+
+&uart1 {
+ fsl,uart-has-rtscts;
+ status = "okay";
+};
+
+&uart2 {
+ fsl,uart-has-rtscts;
+ status = "okay";
+};
+
+&uart3 {
+ fsl,uart-has-rtscts;
+ status = "okay";
+};