sky2: put PHY in sleep when down
Put PHY int sleep mode (from vendor sk98lin 10.50 driver) when the
network device is brought down.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c
index ad35674..59cb9cd 100644
--- a/drivers/net/sky2.c
+++ b/drivers/net/sky2.c
@@ -641,11 +641,47 @@
static void sky2_phy_power_down(struct sky2_hw *hw, unsigned port)
{
u32 reg1;
+ u16 ctrl;
+
+ /* release GPHY Control reset */
+ sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR);
+
+ /* release GMAC reset */
+ sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_CLR);
+
+ if (hw->flags & SKY2_HW_NEWER_PHY) {
+ /* select page 2 to access MAC control register */
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 2);
+
+ ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
+ /* allow GMII Power Down */
+ ctrl &= ~PHY_M_MAC_GMIF_PUP;
+ gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
+
+ /* set page register back to 0 */
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0);
+ }
+
+ /* setup General Purpose Control Register */
+ gma_write16(hw, port, GM_GP_CTRL,
+ GM_GPCR_FL_PASS | GM_GPCR_SPEED_100 | GM_GPCR_AU_ALL_DIS);
+
+ if (hw->chip_id != CHIP_ID_YUKON_EC) {
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U) {
+ ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
+
+ /* enable Power Down */
+ ctrl |= PHY_M_PC_POW_D_ENA;
+ gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
+ }
+
+ /* set IEEE compatible Power Down Mode (dev. #4.99) */
+ gm_phy_write(hw, port, PHY_MARV_CTRL, PHY_CT_PDOWN);
+ }
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
reg1 = sky2_pci_read32(hw, PCI_DEV_REG1);
- reg1 |= phy_power[port];
-
+ reg1 |= phy_power[port]; /* set PHY to PowerDown/COMA Mode */
sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
}
diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h
index c0a5eea..d63106c 100644
--- a/drivers/net/sky2.h
+++ b/drivers/net/sky2.h
@@ -1143,6 +1143,12 @@
PHY_M_PC_ENA_AUTO = 3, /* 11 = Enable Automatic Crossover */
};
+/* for Yukon-EC Ultra Gigabit Ethernet PHY (88E1149 only) */
+enum {
+ PHY_M_PC_COP_TX_DIS = 1<<3, /* Copper Transmitter Disable */
+ PHY_M_PC_POW_D_ENA = 1<<2, /* Power Down Enable */
+};
+
/* for 10/100 Fast Ethernet PHY (88E3082 only) */
enum {
PHY_M_PC_ENA_DTE_DT = 1<<15, /* Enable Data Terminal Equ. (DTE) Detect */
@@ -1411,6 +1417,7 @@
/***** PHY_MARV_PHY_CTRL (page 2) 16 bit r/w MAC Specific Ctrl *****/
enum {
PHY_M_MAC_MD_MSK = 7<<7, /* Bit 9.. 7: Mode Select Mask */
+ PHY_M_MAC_GMIF_PUP = 1<<3, /* GMII Power Up (88E1149 only) */
PHY_M_MAC_MD_AUTO = 3,/* Auto Copper/1000Base-X */
PHY_M_MAC_MD_COPPER = 5,/* Copper only */
PHY_M_MAC_MD_1000BX = 7,/* 1000Base-X only */