IB/core: Ethernet L2 attributes in verbs/cm structures
This patch add the support for Ethernet L2 attributes in the
verbs/cm/cma structures.
When dealing with L2 Ethernet, we should use smac, dmac, vlan ID and priority
in a similar manner that the IB L2 (and the L4 PKEY) attributes are used.
Thus, those attributes were added to the following structures:
* ib_ah_attr - added dmac
* ib_qp_attr - added smac and vlan_id, (sl remains vlan priority)
* ib_wc - added smac, vlan_id
* ib_sa_path_rec - added smac, dmac, vlan_id
* cm_av - added smac and vlan_id
For the path record structure, extra care was taken to avoid the new
fields when packing it into wire format, so we don't break the IB CM
and SA wire protocol.
On the active side, the CM fills. its internal structures from the
path provided by the ULP. We add there taking the ETH L2 attributes
and placing them into the CM Address Handle (struct cm_av).
On the passive side, the CM fills its internal structures from the WC
associated with the REQ message. We add there taking the ETH L2
attributes from the WC.
When the HW driver provides the required ETH L2 attributes in the WC,
they set the IB_WC_WITH_SMAC and IB_WC_WITH_VLAN flags. The IB core
code checks for the presence of these flags, and in their absence does
address resolution from the ib_init_ah_from_wc() helper function.
ib_modify_qp_is_ok is also updated to consider the link layer. Some
parameters are mandatory for Ethernet link layer, while they are
irrelevant for IB. Vendor drivers are modified to support the new
function signature.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
diff --git a/include/rdma/ib_verbs.h b/include/rdma/ib_verbs.h
index 61e1935..ea0f6ee 100644
--- a/include/rdma/ib_verbs.h
+++ b/include/rdma/ib_verbs.h
@@ -48,6 +48,7 @@
#include <linux/rwsem.h>
#include <linux/scatterlist.h>
#include <linux/workqueue.h>
+#include <uapi/linux/if_ether.h>
#include <linux/atomic.h>
#include <asm/uaccess.h>
@@ -472,6 +473,8 @@
u8 static_rate;
u8 ah_flags;
u8 port_num;
+ u8 dmac[ETH_ALEN];
+ u16 vlan_id;
};
enum ib_wc_status {
@@ -524,6 +527,8 @@
IB_WC_WITH_IMM = (1<<1),
IB_WC_WITH_INVALIDATE = (1<<2),
IB_WC_IP_CSUM_OK = (1<<3),
+ IB_WC_WITH_SMAC = (1<<4),
+ IB_WC_WITH_VLAN = (1<<5),
};
struct ib_wc {
@@ -544,6 +549,8 @@
u8 sl;
u8 dlid_path_bits;
u8 port_num; /* valid only for DR SMPs on switches */
+ u8 smac[ETH_ALEN];
+ u16 vlan_id;
};
enum ib_cq_notify_flags {
@@ -721,7 +728,11 @@
IB_QP_MAX_DEST_RD_ATOMIC = (1<<17),
IB_QP_PATH_MIG_STATE = (1<<18),
IB_QP_CAP = (1<<19),
- IB_QP_DEST_QPN = (1<<20)
+ IB_QP_DEST_QPN = (1<<20),
+ IB_QP_SMAC = (1<<21),
+ IB_QP_ALT_SMAC = (1<<22),
+ IB_QP_VID = (1<<23),
+ IB_QP_ALT_VID = (1<<24),
};
enum ib_qp_state {
@@ -771,6 +782,10 @@
u8 rnr_retry;
u8 alt_port_num;
u8 alt_timeout;
+ u8 smac[ETH_ALEN];
+ u8 alt_smac[ETH_ALEN];
+ u16 vlan_id;
+ u16 alt_vlan_id;
};
enum ib_wr_opcode {
@@ -1488,6 +1503,7 @@
* @next_state: Next QP state
* @type: QP type
* @mask: Mask of supplied QP attributes
+ * @ll : link layer of port
*
* This function is a helper function that a low-level driver's
* modify_qp method can use to validate the consumer's input. It
@@ -1496,7 +1512,8 @@
* and that the attribute mask supplied is allowed for the transition.
*/
int ib_modify_qp_is_ok(enum ib_qp_state cur_state, enum ib_qp_state next_state,
- enum ib_qp_type type, enum ib_qp_attr_mask mask);
+ enum ib_qp_type type, enum ib_qp_attr_mask mask,
+ enum rdma_link_layer ll);
int ib_register_event_handler (struct ib_event_handler *event_handler);
int ib_unregister_event_handler(struct ib_event_handler *event_handler);