pcmcia: use dev_printk and dev_dbg in yenta_socket
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
diff --git a/drivers/pcmcia/ti113x.h b/drivers/pcmcia/ti113x.h
index 129db7b..aaa7022 100644
--- a/drivers/pcmcia/ti113x.h
+++ b/drivers/pcmcia/ti113x.h
@@ -339,8 +339,8 @@
mfunc = mfunc_old = config_readl(socket, TI122X_MFUNC);
devctl = config_readb(socket, TI113X_DEVICE_CONTROL);
- printk(KERN_INFO "Yenta TI: socket %s, mfunc 0x%08x, devctl 0x%02x\n",
- pci_name(socket->dev), mfunc, devctl);
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: mfunc 0x%08x, devctl 0x%02x\n", mfunc, devctl);
/* make sure PCI interrupts are enabled before probing */
ti_init(socket);
@@ -354,8 +354,8 @@
* We're here which means PCI interrupts are _not_ delivered. try to
* find the right setting (all serial or parallel)
*/
- printk(KERN_INFO "Yenta TI: socket %s probing PCI interrupt failed, trying to fix\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: probing PCI interrupt failed, trying to fix\n");
/* for serial PCI make sure MFUNC3 is set to IRQSER */
if ((devctl & TI113X_DCR_IMODE_MASK) == TI12XX_DCR_IMODE_ALL_SERIAL) {
@@ -379,8 +379,8 @@
pci_irq_status = yenta_probe_cb_irq(socket);
if (pci_irq_status == 1) {
- printk(KERN_INFO "Yenta TI: socket %s all-serial interrupts ok\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: all-serial interrupts ok\n");
mfunc_old = mfunc;
goto out;
}
@@ -395,8 +395,8 @@
}
/* serial PCI interrupts not working fall back to parallel */
- printk(KERN_INFO "Yenta TI: socket %s falling back to parallel PCI interrupts\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: falling back to parallel PCI interrupts\n");
devctl &= ~TI113X_DCR_IMODE_MASK;
devctl |= TI113X_DCR_IMODE_SERIAL; /* serial ISA could be right */
config_writeb(socket, TI113X_DEVICE_CONTROL, devctl);
@@ -427,8 +427,8 @@
pci_irq_status = yenta_probe_cb_irq(socket);
if (pci_irq_status == 1) {
mfunc_old = mfunc;
- printk(KERN_INFO "Yenta TI: socket %s parallel PCI interrupts ok\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: parallel PCI interrupts ok\n");
} else {
/* not working, back to old value */
mfunc = mfunc_old;
@@ -440,8 +440,9 @@
out:
if (pci_irq_status < 1) {
socket->cb_irq = 0;
- printk(KERN_INFO "Yenta TI: socket %s no PCI interrupts. Fish. Please report.\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "Yenta TI: no PCI interrupts. Fish. "
+ "Please report.\n");
}
}
@@ -513,8 +514,9 @@
mfunc = mfunc_old = config_readl(socket, TI122X_MFUNC);
devctl = config_readb(socket, TI113X_DEVICE_CONTROL);
- printk(KERN_INFO "Yenta TI: socket %s, mfunc 0x%08x, devctl 0x%02x\n",
- pci_name(socket->dev), mfunc, devctl);
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: mfunc 0x%08x, devctl 0x%02x\n",
+ mfunc, devctl);
/* if IRQs are configured as tied, align irq of func1 with func0 */
sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
@@ -533,9 +535,8 @@
* We're here which means PCI interrupts are _not_ delivered. try to
* find the right setting
*/
- printk(KERN_INFO "Yenta TI: socket %s probing PCI interrupt failed, trying to fix\n",
- pci_name(socket->dev));
-
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: probing PCI interrupt failed, trying to fix\n");
/* if all serial: set INTRTIE, probe again */
if ((devctl & TI113X_DCR_IMODE_MASK) == TI12XX_DCR_IMODE_ALL_SERIAL) {
@@ -544,8 +545,8 @@
if (ti12xx_tie_interrupts(socket, &old_irq)) {
pci_irq_status = yenta_probe_cb_irq(socket);
if (pci_irq_status == 1) {
- printk(KERN_INFO "Yenta TI: socket %s all-serial interrupts, tied ok\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: all-serial interrupts, tied ok\n");
goto out;
}
@@ -582,8 +583,8 @@
pci_irq_status = yenta_probe_cb_irq(socket);
if (pci_irq_status == 1) {
- printk(KERN_INFO "Yenta TI: socket %s parallel PCI interrupts ok\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: parallel PCI interrupts ok\n");
goto out;
}
@@ -593,13 +594,13 @@
if (pci_irq_status == -1)
goto out;
}
-
+
/* still nothing: set INTRTIE */
if (ti12xx_tie_interrupts(socket, &old_irq)) {
pci_irq_status = yenta_probe_cb_irq(socket);
if (pci_irq_status == 1) {
- printk(KERN_INFO "Yenta TI: socket %s parallel PCI interrupts, tied ok\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: parallel PCI interrupts, tied ok\n");
goto out;
}
@@ -610,8 +611,8 @@
out:
if (pci_irq_status < 1) {
socket->cb_irq = 0;
- printk(KERN_INFO "Yenta TI: socket %s no PCI interrupts. Fish. Please report.\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: no PCI interrupts. Fish. Please report.\n");
}
}
@@ -815,11 +816,13 @@
/* make sure that memory burst is active */
val_orig = val = config_readl(socket, TI113X_SYSTEM_CONTROL);
if (disable_clkrun && PCI_FUNC(socket->dev->devfn) == 0) {
- printk(KERN_INFO "Yenta: Disabling CLKRUN feature\n");
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "Disabling CLKRUN feature\n");
val |= TI113X_SCR_KEEPCLK;
}
if (!(val & TI122X_SCR_MRBURSTUP)) {
- printk(KERN_INFO "Yenta: Enabling burst memory read transactions\n");
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "Enabling burst memory read transactions\n");
val |= TI122X_SCR_MRBURSTUP;
}
if (val_orig != val)
@@ -830,10 +833,12 @@
* CSC interrupts to PCI rather than INTVAL.
*/
val = config_readb(socket, TI1250_DIAGNOSTIC);
- printk(KERN_INFO "Yenta: Using %s to route CSC interrupts to PCI\n",
- (val & TI1250_DIAG_PCI_CSC) ? "CSCINT" : "INTVAL");
- printk(KERN_INFO "Yenta: Routing CardBus interrupts to %s\n",
- (val & TI1250_DIAG_PCI_IREQ) ? "PCI" : "ISA");
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "Using %s to route CSC interrupts to PCI\n",
+ (val & TI1250_DIAG_PCI_CSC) ? "CSCINT" : "INTVAL");
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "Routing CardBus interrupts to %s\n",
+ (val & TI1250_DIAG_PCI_IREQ) ? "PCI" : "ISA");
/* do irqrouting, depending on function */
if (PCI_FUNC(socket->dev->devfn) == 0)
@@ -858,8 +863,9 @@
diag |= TI1250_DIAG_PCI_CSC | TI1250_DIAG_PCI_IREQ;
if (diag != old) {
- printk(KERN_INFO "Yenta: adjusting diagnostic: %02x -> %02x\n",
- old, diag);
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "adjusting diagnostic: %02x -> %02x\n",
+ old, diag);
config_writeb(socket, TI1250_DIAGNOSTIC, diag);
}
@@ -924,7 +930,9 @@
/* default to clear TLTEnable bit, old behaviour */
test_c9 &= ~ENE_TEST_C9_TLTENABLE;
- printk(KERN_INFO "yenta EnE: chaning testregister 0xC9, %02x -> %02x\n", old_c9, test_c9);
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "EnE: chaning testregister 0xC9, %02x -> %02x\n",
+ old_c9, test_c9);
config_writeb(socket, ENE_TEST_C9, test_c9);
}