Merge tag 'mvebu-dt-3.14-5' of git://git.infradead.org/linux-mvebu into next/dt
From Jason Cooper:
mvebu DT changes for v3.14 (incremental #5)
- mvebu
- add rtc chip isl12057 node to ReadyNAS boards
- fix register length in Armada XP pmsu
- kirkwood
- sort ocp nodes by address in 6282 dtsi file
- add 6192 dtsi file
- add LaPlug board
- add sata phy node
- dove
- add sata phy node
* tag 'mvebu-dt-3.14-5' of git://git.infradead.org/linux-mvebu:
ARM: Kirkwood: DT board setup for LaPlug
ARM: Kirkwood: Add 6192 DTSI file
ARM: mvebu: fix register length for Armada XP PMSU
ARM: kirkwood: 6282: sort DT nodes by address
Phy: Add DT nodes on kirkwood and Dove for the SATA PHY
ARM: mvebu: Enable ISL12057 RTC chip in ReadyNAS 2120 .dts file
ARM: mvebu: Enable ISL12057 RTC chip in ReadyNAS 104 .dts file
ARM: mvebu: Enable ISL12057 RTC chip in ReadyNAS 102 .dts file
Signed-off-by: Olof Johansson <olof@lixom.net>
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 25d708c..2752a13 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -88,6 +88,7 @@
kirkwood-iomega_ix2_200.dtb \
kirkwood-is2.dtb \
kirkwood-km_kirkwood.dtb \
+ kirkwood-laplug.dtb \
kirkwood-lschlv2.dtb \
kirkwood-lsxhl.dtb \
kirkwood-mplcec4.dtb \
diff --git a/arch/arm/boot/dts/armada-370-netgear-rn102.dts b/arch/arm/boot/dts/armada-370-netgear-rn102.dts
index 6a7383f..651aeb5 100644
--- a/arch/arm/boot/dts/armada-370-netgear-rn102.dts
+++ b/arch/arm/boot/dts/armada-370-netgear-rn102.dts
@@ -122,6 +122,11 @@
clock-frequency = <100000>;
status = "okay";
+ isl12057: isl12057@68 {
+ compatible = "isl,isl12057";
+ reg = <0x68>;
+ };
+
g762: g762@3e {
compatible = "gmt,g762";
reg = <0x3e>;
diff --git a/arch/arm/boot/dts/armada-370-netgear-rn104.dts b/arch/arm/boot/dts/armada-370-netgear-rn104.dts
index 272e2e2..4e27587 100644
--- a/arch/arm/boot/dts/armada-370-netgear-rn104.dts
+++ b/arch/arm/boot/dts/armada-370-netgear-rn104.dts
@@ -117,6 +117,11 @@
clock-frequency = <100000>;
status = "okay";
+ isl12057: isl12057@68 {
+ compatible = "isl,isl12057";
+ reg = <0x68>;
+ };
+
g762: g762@3e {
compatible = "gmt,g762";
reg = <0x3e>;
diff --git a/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts b/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts
index f048b4e..ff049ee 100644
--- a/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts
+++ b/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts
@@ -174,6 +174,11 @@
clock-frequency = <400000>;
status = "okay";
+ isl12057: isl12057@68 {
+ compatible = "isl,isl12057";
+ reg = <0x68>;
+ };
+
/* Controller for rear fan #1 of 3 (Protechnic
* MGT4012XB-O20, 8000RPM) near eSATA port */
g762_fan1: g762@3e {
diff --git a/arch/arm/boot/dts/armada-xp.dtsi b/arch/arm/boot/dts/armada-xp.dtsi
index 4919fb8..b8b84a2 100644
--- a/arch/arm/boot/dts/armada-xp.dtsi
+++ b/arch/arm/boot/dts/armada-xp.dtsi
@@ -113,7 +113,7 @@
armada-370-xp-pmsu@22000 {
compatible = "marvell,armada-370-xp-pmsu";
- reg = <0x22100 0x430>, <0x20800 0x20>;
+ reg = <0x22100 0x400>, <0x20800 0x20>;
};
eth2: ethernet@30000 {
diff --git a/arch/arm/boot/dts/dove.dtsi b/arch/arm/boot/dts/dove.dtsi
index 852db28..8de1031 100644
--- a/arch/arm/boot/dts/dove.dtsi
+++ b/arch/arm/boot/dts/dove.dtsi
@@ -336,10 +336,21 @@
reg = <0xa0000 0x2400>;
interrupts = <62>;
clocks = <&gate_clk 3>;
+ phys = <&sata_phy0>;
+ phy-names = "port0";
nr-ports = <1>;
status = "disabled";
};
+ sata_phy0: sata-phy@a2000 {
+ compatible = "marvell,mvebu-sata-phy";
+ reg = <0xa2000 0x0334>;
+ clocks = <&gate_clk 3>;
+ clock-names = "sata";
+ #phy-cells = <0>;
+ status = "ok";
+ };
+
audio0: audio-controller@b0000 {
compatible = "marvell,dove-audio";
reg = <0xb0000 0x2210>;
diff --git a/arch/arm/boot/dts/kirkwood-6192.dtsi b/arch/arm/boot/dts/kirkwood-6192.dtsi
new file mode 100644
index 0000000..3916937
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-6192.dtsi
@@ -0,0 +1,107 @@
+/ {
+ mbus {
+ pcie-controller {
+ compatible = "marvell,kirkwood-pcie";
+ status = "disabled";
+ device_type = "pci";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ bus-range = <0x00 0xff>;
+
+ ranges =
+ <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
+ 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
+ 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */>;
+
+ pcie@1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x00040000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+ 0x81000000 0 0 0x81000000 0x1 0 1 0>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &intc 9>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gate_clk 2>;
+ status = "disabled";
+ };
+ };
+ };
+
+ ocp@f1000000 {
+ pinctrl: pinctrl@10000 {
+ compatible = "marvell,88f6192-pinctrl";
+ reg = <0x10000 0x20>;
+
+ pmx_nand: pmx-nand {
+ marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3",
+ "mpp4", "mpp5", "mpp18",
+ "mpp19";
+ marvell,function = "nand";
+ };
+ pmx_sata0: pmx-sata0 {
+ marvell,pins = "mpp5", "mpp21", "mpp23";
+ marvell,function = "sata0";
+ };
+ pmx_sata1: pmx-sata1 {
+ marvell,pins = "mpp4", "mpp20", "mpp22";
+ marvell,function = "sata1";
+ };
+ pmx_spi: pmx-spi {
+ marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3";
+ marvell,function = "spi";
+ };
+ pmx_twsi0: pmx-twsi0 {
+ marvell,pins = "mpp8", "mpp9";
+ marvell,function = "twsi0";
+ };
+ pmx_uart0: pmx-uart0 {
+ marvell,pins = "mpp10", "mpp11";
+ marvell,function = "uart0";
+ };
+ pmx_uart1: pmx-uart1 {
+ marvell,pins = "mpp13", "mpp14";
+ marvell,function = "uart1";
+ };
+ pmx_sdio: pmx-sdio {
+ marvell,pins = "mpp12", "mpp13", "mpp14",
+ "mpp15", "mpp16", "mpp17";
+ marvell,function = "sdio";
+ };
+ };
+
+ rtc@10300 {
+ compatible = "marvell,kirkwood-rtc", "marvell,orion-rtc";
+ reg = <0x10300 0x20>;
+ interrupts = <53>;
+ clocks = <&gate_clk 7>;
+ };
+
+ sata@80000 {
+ compatible = "marvell,orion-sata";
+ reg = <0x80000 0x5000>;
+ interrupts = <21>;
+ clocks = <&gate_clk 14>, <&gate_clk 15>;
+ clock-names = "0", "1";
+ status = "disabled";
+ };
+
+ mvsdio@90000 {
+ compatible = "marvell,orion-sdio";
+ reg = <0x90000 0x200>;
+ interrupts = <28>;
+ clocks = <&gate_clk 4>;
+ bus-width = <4>;
+ cap-sdio-irq;
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ status = "disabled";
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/kirkwood-6281.dtsi b/arch/arm/boot/dts/kirkwood-6281.dtsi
index e4e1968..416d96e 100644
--- a/arch/arm/boot/dts/kirkwood-6281.dtsi
+++ b/arch/arm/boot/dts/kirkwood-6281.dtsi
@@ -89,6 +89,8 @@
interrupts = <21>;
clocks = <&gate_clk 14>, <&gate_clk 15>;
clock-names = "0", "1";
+ phys = <&sata_phy0>, <&sata_phy1>;
+ phy-names = "port0", "port1";
status = "disabled";
};
diff --git a/arch/arm/boot/dts/kirkwood-6282.dtsi b/arch/arm/boot/dts/kirkwood-6282.dtsi
index f010c21..2902e0d 100644
--- a/arch/arm/boot/dts/kirkwood-6282.dtsi
+++ b/arch/arm/boot/dts/kirkwood-6282.dtsi
@@ -104,6 +104,12 @@
};
};
+ thermal@10078 {
+ compatible = "marvell,kirkwood-thermal";
+ reg = <0x10078 0x4>;
+ status = "okay";
+ };
+
rtc@10300 {
compatible = "marvell,kirkwood-rtc", "marvell,orion-rtc";
reg = <0x10300 0x20>;
@@ -111,12 +117,25 @@
clocks = <&gate_clk 7>;
};
+ i2c@11100 {
+ compatible = "marvell,mv64xxx-i2c";
+ reg = <0x11100 0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <32>;
+ clock-frequency = <100000>;
+ clocks = <&gate_clk 7>;
+ status = "disabled";
+ };
+
sata@80000 {
compatible = "marvell,orion-sata";
reg = <0x80000 0x5000>;
interrupts = <21>;
clocks = <&gate_clk 14>, <&gate_clk 15>;
clock-names = "0", "1";
+ phys = <&sata_phy0>, <&sata_phy1>;
+ phy-names = "port0", "port1";
status = "disabled";
};
@@ -133,23 +152,5 @@
cap-mmc-highspeed;
status = "disabled";
};
-
- thermal@10078 {
- compatible = "marvell,kirkwood-thermal";
- reg = <0x10078 0x4>;
- status = "okay";
- };
-
- i2c@11100 {
- compatible = "marvell,mv64xxx-i2c";
- reg = <0x11100 0x20>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <32>;
- clock-frequency = <100000>;
- clocks = <&gate_clk 7>;
- status = "disabled";
- };
-
};
};
diff --git a/arch/arm/boot/dts/kirkwood-laplug.dts b/arch/arm/boot/dts/kirkwood-laplug.dts
new file mode 100644
index 0000000..c9e82ef
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-laplug.dts
@@ -0,0 +1,175 @@
+/*
+ * Copyright (C) 2013 Maxime Hadjinlian <maxime.hadjinlian@gmail.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "kirkwood.dtsi"
+#include "kirkwood-6192.dtsi"
+
+/ {
+ model = "LaCie LaPlug";
+ compatible = "lacie,laplug", "marvell,kirkwood-88f6192", "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x8000000>; /* 128 MB */
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk";
+ };
+
+ mbus {
+ pcie-controller {
+ status = "okay";
+ pcie@1,0 {
+ status = "okay";
+ };
+ };
+ };
+
+ ocp@f1000000 {
+ serial@12000 {
+ pinctrl-0 = <&pmx_uart0>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ i2c@11000 {
+ pinctrl-0 = <&pmx_twsi0>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ eeprom@50 {
+ compatible = "at,24c04";
+ pagesize = <16>;
+ reg = <0x50>;
+ };
+ };
+
+ pinctrl: pinctrl@10000 {
+ pmx_usb_power_enable: pmx-usb-power-enable {
+ marvell,pins = "mpp14";
+ marvell,function = "gpio";
+ };
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ button@1{
+ label = "Power push button";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ red-fail {
+ label = "laplug_v2:red:power";
+ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+ };
+ blue-power {
+ label = "laplug_v2:blue:power";
+ gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+ };
+
+ gpio_poweroff {
+ compatible = "gpio-poweroff";
+ gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>;
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_usb_power_enable>;
+ pinctrl-names = "default";
+
+ usb_power_back1: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "USB Power Back 1";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+ };
+
+ usb_power_back2: regulator@2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "USB Power Back 2";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 28 GPIO_ACTIVE_HIGH>;
+ };
+
+ usb_power_front: regulator@3 {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ regulator-name = "USB Power Front";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&nand {
+ /* Total size : 512MB */
+ status = "okay";
+ pinctrl-0 = <&pmx_nand>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0 0x100000>; /* 1MB */
+ read-only;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x100000 0x1000000>; /* 16MB */
+ };
+
+ partition@1100000 {
+ label = "rootfs";
+ reg = <0x1100000 0x1EF00000>; /* 495MB */
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy@0 {
+ device_type = "ethernet-phy";
+ reg = <0>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ ethernet0-port@0 {
+ phy-handle = <ðphy0>;
+ };
+};
diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi
index 1da94c1..81e6c40 100644
--- a/arch/arm/boot/dts/kirkwood.dtsi
+++ b/arch/arm/boot/dts/kirkwood.dtsi
@@ -284,5 +284,23 @@
/* set phy-handle property in board file */
};
};
+
+ sata_phy0: sata-phy@82000 {
+ compatible = "marvell,mvebu-sata-phy";
+ reg = <0x82000 0x0334>;
+ clocks = <&gate_clk 14>;
+ clock-names = "sata";
+ #phy-cells = <0>;
+ status = "ok";
+ };
+
+ sata_phy1: sata-phy@84000 {
+ compatible = "marvell,mvebu-sata-phy";
+ reg = <0x84000 0x0334>;
+ clocks = <&gate_clk 15>;
+ clock-names = "sata";
+ #phy-cells = <0>;
+ status = "ok";
+ };
};
};