[ARM] 3595/1: ixp4xx/nas100d: Board support for new LED subsystem

Patch from Rod Whitby

This patch implements NEW_LEDS support for the IOMega NAS100d.  The
NAS100d has three LED indicators, which are the only form of output
for an unmodified device - there is no keyboard or display on an
NAS100d.  For an NAS100d which has been modified to bring out the
serial port console, it is important to register that device first
separately, to enable debugging of other device support.

Signed-off-by: John Bowler <jbowler@acm.org>
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
diff --git a/arch/arm/mach-ixp4xx/nas100d-setup.c b/arch/arm/mach-ixp4xx/nas100d-setup.c
index a3b4c6a..9a31444 100644
--- a/arch/arm/mach-ixp4xx/nas100d-setup.c
+++ b/arch/arm/mach-ixp4xx/nas100d-setup.c
@@ -15,6 +15,7 @@
 #include <linux/kernel.h>
 #include <linux/serial.h>
 #include <linux/serial_8250.h>
+#include <linux/leds.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -37,6 +38,36 @@
 	.resource		= &nas100d_flash_resource,
 };
 
+#ifdef CONFIG_LEDS_IXP4XX
+static struct resource nas100d_led_resources[] = {
+	{
+		.name		= "wlan",   /* green led */
+		.start		= 0,
+		.end		= 0,
+		.flags		= IXP4XX_GPIO_LOW,
+	},
+	{
+		.name		= "ready",  /* blue power led (off is flashing!) */
+		.start		= 15,
+		.end		= 15,
+		.flags		= IXP4XX_GPIO_LOW,
+	},
+	{
+		.name		= "disk",   /* yellow led */
+		.start		= 3,
+		.end		= 3,
+		.flags		= IXP4XX_GPIO_LOW,
+	},
+};
+
+static struct platform_device nas100d_leds = {
+	.name			= "IXP4XX-GPIO-LED",
+	.id			= -1,
+	.num_resources		= ARRAY_SIZE(nas100d_led_resources),
+	.resource		= nas100d_led_resources,
+};
+#endif
+
 static struct ixp4xx_i2c_pins nas100d_i2c_gpio_pins = {
 	.sda_pin		= NAS100D_SDA_PIN,
 	.scl_pin		= NAS100D_SCL_PIN,
@@ -95,7 +126,9 @@
 static struct platform_device *nas100d_devices[] __initdata = {
 	&nas100d_i2c_controller,
 	&nas100d_flash,
-	&nas100d_uart,
+#ifdef CONFIG_LEDS_IXP4XX
+	&nas100d_leds,
+#endif
 };
 
 static void nas100d_power_off(void)
@@ -122,6 +155,12 @@
 
 	pm_power_off = nas100d_power_off;
 
+	/* This is only useful on a modified machine, but it is valuable
+	 * to have it first in order to see debug messages, and so that
+	 * it does *not* get removed if platform_add_devices fails!
+	 */
+	(void)platform_device_register(&nas100d_uart);
+
 	platform_add_devices(nas100d_devices, ARRAY_SIZE(nas100d_devices));
 }