icside: remove superfluous ->maskproc method
[inspired by pata_icside]
Enabling/disabling of card IRQs is handled fine by IRQ and IDE
subsystems so there is no need for custom ->maskproc method.
Moreover icside_maskproc() would enable IRQ only if it was already
enabled [because of 'if (state->enabled && !mask)' check].
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
diff --git a/drivers/ide/icside.c b/drivers/ide/icside.c
index c5269fa..5af3d0f 100644
--- a/drivers/ide/icside.c
+++ b/drivers/ide/icside.c
@@ -65,8 +65,6 @@
};
struct icside_state {
- unsigned int channel;
- unsigned int enabled;
void __iomem *irq_port;
void __iomem *ioc_base;
unsigned int sel;
@@ -116,18 +114,11 @@
struct icside_state *state = ec->irq_data;
void __iomem *base = state->irq_port;
- state->enabled = 1;
+ writeb(0, base + ICS_ARCIN_V6_INTROFFSET_1);
+ readb(base + ICS_ARCIN_V6_INTROFFSET_2);
- switch (state->channel) {
- case 0:
- writeb(0, base + ICS_ARCIN_V6_INTROFFSET_1);
- readb(base + ICS_ARCIN_V6_INTROFFSET_2);
- break;
- case 1:
- writeb(0, base + ICS_ARCIN_V6_INTROFFSET_2);
- readb(base + ICS_ARCIN_V6_INTROFFSET_1);
- break;
- }
+ writeb(0, base + ICS_ARCIN_V6_INTROFFSET_2);
+ readb(base + ICS_ARCIN_V6_INTROFFSET_1);
}
/* Prototype: icside_irqdisable_arcin_v6 (struct expansion_card *ec, int irqnr)
@@ -137,8 +128,6 @@
{
struct icside_state *state = ec->irq_data;
- state->enabled = 0;
-
readb(state->irq_port + ICS_ARCIN_V6_INTROFFSET_1);
readb(state->irq_port + ICS_ARCIN_V6_INTROFFSET_2);
}
@@ -160,44 +149,6 @@
.irqpending = icside_irqpending_arcin_v6,
};
-/*
- * Handle routing of interrupts. This is called before
- * we write the command to the drive.
- */
-static void icside_maskproc(ide_drive_t *drive, int mask)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct expansion_card *ec = ECARD_DEV(hwif->dev);
- struct icside_state *state = ecard_get_drvdata(ec);
- unsigned long flags;
-
- local_irq_save(flags);
-
- state->channel = hwif->channel;
-
- if (state->enabled && !mask) {
- switch (hwif->channel) {
- case 0:
- writeb(0, state->irq_port + ICS_ARCIN_V6_INTROFFSET_1);
- readb(state->irq_port + ICS_ARCIN_V6_INTROFFSET_2);
- break;
- case 1:
- writeb(0, state->irq_port + ICS_ARCIN_V6_INTROFFSET_2);
- readb(state->irq_port + ICS_ARCIN_V6_INTROFFSET_1);
- break;
- }
- } else {
- readb(state->irq_port + ICS_ARCIN_V6_INTROFFSET_2);
- readb(state->irq_port + ICS_ARCIN_V6_INTROFFSET_1);
- }
-
- local_irq_restore(flags);
-}
-
-static const struct ide_port_ops icside_v6_no_dma_port_ops = {
- .maskproc = icside_maskproc,
-};
-
#ifdef CONFIG_BLK_DEV_IDEDMA_ICS
/*
* SG-DMA support.
@@ -275,7 +226,6 @@
static const struct ide_port_ops icside_v6_port_ops = {
.set_dma_mode = icside_set_dma_mode,
- .maskproc = icside_maskproc,
};
static void icside_dma_host_set(ide_drive_t *drive, int on)
@@ -320,11 +270,6 @@
BUG_ON(dma_channel_active(ec->dma));
/*
- * Ensure that we have the right interrupt routed.
- */
- icside_maskproc(drive, 0);
-
- /*
* Route the DMA signals to the correct interface.
*/
writeb(state->sel | hwif->channel, state->ioc_base);
@@ -452,7 +397,6 @@
static const struct ide_port_info icside_v6_port_info __initdata = {
.init_dma = icside_dma_off_init,
- .port_ops = &icside_v6_no_dma_port_ops,
.dma_ops = &icside_v6_dma_ops,
.host_flags = IDE_HFLAG_SERIALIZE | IDE_HFLAG_MMIO,
.mwdma_mask = ATA_MWDMA2,