| /* |
| * Yucca board definitions |
| * |
| * Roland Dreier <rolandd@cisco.com> (based on luan.h by Matt Porter) |
| * |
| * Copyright 2004-2005 MontaVista Software Inc. |
| * Copyright (c) 2005 Cisco Systems. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify it |
| * under the terms of the GNU General Public License as published by the |
| * Free Software Foundation; either version 2 of the License, or (at your |
| * option) any later version. |
| * |
| */ |
| |
| #ifdef __KERNEL__ |
| #ifndef __ASM_YUCCA_H__ |
| #define __ASM_YUCCA_H__ |
| |
| #include <linux/config.h> |
| #include <platforms/4xx/ppc440spe.h> |
| |
| /* F/W TLB mapping used in bootloader glue to reset EMAC */ |
| #define PPC44x_EMAC0_MR0 0xa0000800 |
| |
| /* Location of MAC addresses in PIBS image */ |
| #define PIBS_FLASH_BASE 0xffe00000 |
| #define PIBS_MAC_BASE (PIBS_FLASH_BASE+0x1b0400) |
| |
| /* External timer clock frequency */ |
| #define YUCCA_TMR_CLK 25000000 |
| |
| /* |
| * FPGA registers |
| */ |
| #define YUCCA_FPGA_REG_BASE 0x00000004e2000000ULL |
| #define YUCCA_FPGA_REG_SIZE 0x24 |
| |
| #define FPGA_REG1A 0x1a |
| |
| #define FPGA_REG1A_PE0_GLED 0x8000 |
| #define FPGA_REG1A_PE1_GLED 0x4000 |
| #define FPGA_REG1A_PE2_GLED 0x2000 |
| #define FPGA_REG1A_PE0_YLED 0x1000 |
| #define FPGA_REG1A_PE1_YLED 0x0800 |
| #define FPGA_REG1A_PE2_YLED 0x0400 |
| #define FPGA_REG1A_PE0_PWRON 0x0200 |
| #define FPGA_REG1A_PE1_PWRON 0x0100 |
| #define FPGA_REG1A_PE2_PWRON 0x0080 |
| #define FPGA_REG1A_PE0_REFCLK_ENABLE 0x0040 |
| #define FPGA_REG1A_PE1_REFCLK_ENABLE 0x0020 |
| #define FPGA_REG1A_PE2_REFCLK_ENABLE 0x0010 |
| #define FPGA_REG1A_PE_SPREAD0 0x0008 |
| #define FPGA_REG1A_PE_SPREAD1 0x0004 |
| #define FPGA_REG1A_PE_SELSOURCE_0 0x0002 |
| #define FPGA_REG1A_PE_SELSOURCE_1 0x0001 |
| |
| #define FPGA_REG1C 0x1c |
| |
| #define FPGA_REG1C_PE0_ROOTPOINT 0x8000 |
| #define FPGA_REG1C_PE1_ENDPOINT 0x4000 |
| #define FPGA_REG1C_PE2_ENDPOINT 0x2000 |
| #define FPGA_REG1C_PE0_PRSNT 0x1000 |
| #define FPGA_REG1C_PE1_PRSNT 0x0800 |
| #define FPGA_REG1C_PE2_PRSNT 0x0400 |
| #define FPGA_REG1C_PE0_WAKE 0x0080 |
| #define FPGA_REG1C_PE1_WAKE 0x0040 |
| #define FPGA_REG1C_PE2_WAKE 0x0020 |
| #define FPGA_REG1C_PE0_PERST 0x0010 |
| #define FPGA_REG1C_PE1_PERST 0x0008 |
| #define FPGA_REG1C_PE2_PERST 0x0004 |
| |
| /* |
| * Serial port defines |
| */ |
| #define RS_TABLE_SIZE 3 |
| |
| /* PIBS defined UART mappings, used before early_serial_setup */ |
| #define UART0_IO_BASE 0xa0000200 |
| #define UART1_IO_BASE 0xa0000300 |
| #define UART2_IO_BASE 0xa0000600 |
| |
| #define BASE_BAUD 11059200 |
| #define STD_UART_OP(num) \ |
| { 0, BASE_BAUD, 0, UART##num##_INT, \ |
| (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST), \ |
| iomem_base: (void*)UART##num##_IO_BASE, \ |
| io_type: SERIAL_IO_MEM}, |
| |
| #define SERIAL_PORT_DFNS \ |
| STD_UART_OP(0) \ |
| STD_UART_OP(1) \ |
| STD_UART_OP(2) |
| |
| /* PCI support */ |
| #define YUCCA_PCIX_LOWER_IO 0x00000000 |
| #define YUCCA_PCIX_UPPER_IO 0x0000ffff |
| #define YUCCA_PCIX_LOWER_MEM 0x80000000 |
| #define YUCCA_PCIX_UPPER_MEM 0x8fffffff |
| #define YUCCA_PCIE_LOWER_MEM 0x90000000 |
| #define YUCCA_PCIE_MEM_SIZE 0x10000000 |
| |
| #define YUCCA_PCIX_MEM_SIZE 0x10000000 |
| #define YUCCA_PCIX_MEM_OFFSET 0x00000000 |
| #define YUCCA_PCIE_MEM_SIZE 0x10000000 |
| #define YUCCA_PCIE_MEM_OFFSET 0x00000000 |
| |
| #endif /* __ASM_YUCCA_H__ */ |
| #endif /* __KERNEL__ */ |