diff --git a/Documentation/devicetree/bindings/serial/arm,mps2-uart.txt b/Documentation/devicetree/bindings/serial/arm,mps2-uart.txt
new file mode 100644
index 0000000..128cc6a
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/arm,mps2-uart.txt
@@ -0,0 +1,19 @@
+ARM MPS2 UART
+
+Required properties:
+- compatible	: Should be "arm,mps2-uart"
+- reg		: Address and length of the register set
+- interrupts	: Reference to the UART RX, TX and overrun interrupts
+
+Required clocking property:
+- clocks	  : The input clock of the UART
+
+
+Examples:
+
+uart0: serial@40004000 {
+	compatible = "arm,mps2-uart";
+	reg = <0x40004000 0x1000>;
+	interrupts = <0 1 12>;
+	clocks = <&sysclk>;
+};
diff --git a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
index ed94c21..1e82802 100644
--- a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
+++ b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
@@ -6,7 +6,7 @@
 - interrupts : Should contain uart interrupt
 
 Optional properties:
-- fsl,uart-has-rtscts : Indicate the uart has rts and cts
+- uart-has-rtscts : Indicate the uart has rts and cts
 - fsl,irda-mode : Indicate the uart supports irda mode
 - fsl,dte-mode : Indicate the uart works in DTE mode. The uart works
                   in DCE mode by default.
@@ -24,6 +24,6 @@
 	compatible = "fsl,imx51-uart", "fsl,imx21-uart";
 	reg = <0x73fbc000 0x4000>;
 	interrupts = <31>;
-	fsl,uart-has-rtscts;
+	uart-has-rtscts;
 	fsl,dte-mode;
 };
diff --git a/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt b/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt
index 7c408c8..5c96d41 100644
--- a/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt
+++ b/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt
@@ -1,8 +1,10 @@
 * Freescale MXS Application UART (AUART)
 
-Required properties:
-- compatible : Should be "fsl,<soc>-auart". The supported SoCs include
-  imx23 and imx28.
+Required properties for all SoCs:
+- compatible : Should be one of fallowing variants:
+	"fsl,imx23-auart" - Freescale i.MX23
+	"fsl,imx28-auart" - Freescale i.MX28
+	"alphascale,asm9260-auart" - Alphascale ASM9260
 - reg : Address and length of the register set for the device
 - interrupts : Should contain the auart interrupt numbers
 - dmas: DMA specifier, consisting of a phandle to DMA controller node
@@ -10,8 +12,14 @@
   Refer to dma.txt and fsl-mxs-dma.txt for details.
 - dma-names: "rx" for RX channel, "tx" for TX channel.
 
+Required properties for "alphascale,asm9260-auart":
+- clocks : the clocks feeding the watchdog timer. See clock-bindings.txt
+- clock-names : should be set to
+	"mod" - source for tick counter.
+	"ahb" - ahb gate.
+
 Optional properties:
-- fsl,uart-has-rtscts : Indicate the UART has RTS and CTS lines
+- uart-has-rtscts : Indicate the UART has RTS and CTS lines
   for hardware flow control,
 	it also means you enable the DMA support for this UART.
 - {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD
diff --git a/Documentation/devicetree/bindings/serial/serial.txt b/Documentation/devicetree/bindings/serial/serial.txt
new file mode 100644
index 0000000..fd970f7
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/serial.txt
@@ -0,0 +1,57 @@
+Generic Serial DT Bindings
+
+This document lists a set of generic properties for describing UARTs in a
+device tree.  Whether these properties apply to a particular device depends on
+the DT bindings for the actual device.
+
+Optional properties:
+  - cts-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be
+    used as the UART's CTS line.
+  - dcd-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be
+    used as the UART's DCD line.
+  - dsr-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be
+    used as the UART's DSR line.
+  - dtr-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be
+    used as the UART's DTR line.
+  - rng-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be
+    used as the UART's RNG line.
+  - rts-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be
+    used as the UART's RTS line.
+
+  - uart-has-rtscts: The presence of this property indicates that the
+    UART has dedicated lines for RTS/CTS hardware flow control, and that
+    they are available for use (wired and enabled by pinmux configuration).
+    This depends on both the UART hardware and the board wiring.
+    Note that this property is mutually-exclusive with "cts-gpios" and
+    "rts-gpios" above.
+
+
+Examples:
+
+	uart1: serial@48022000 {
+		compatible = "ti,am3352-uart", "ti,omap3-uart";
+		ti,hwmods = "uart2";
+		clock-frequency = <48000000>;
+		reg = <0x48022000 0x2000>;
+		interrupts = <73>;
+		dmas = <&edma 28 0>, <&edma 29 0>;
+		dma-names = "tx", "rx";
+		dtr-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>;
+		dsr-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+		dcd-gpios = <&gpio2 24 GPIO_ACTIVE_LOW>;
+		rng-gpios = <&gpio2 25 GPIO_ACTIVE_LOW>;
+		cts-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+		rts-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+		status = "okay";
+	};
+
+	scifa4: serial@e6c80000 {
+		compatible = "renesas,scifa-sh73a0", "renesas,scifa";
+		reg = <0xe6c80000 0x100>;
+		interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&mstp2_clks SH73A0_CLK_SCIFA4>;
+		clock-names = "fck";
+		power-domains = <&pd_a3sp>;
+		uart-has-rtscts;
+		status = "okay";
+	};
diff --git a/Documentation/devicetree/bindings/serial/sirf-uart.txt b/Documentation/devicetree/bindings/serial/sirf-uart.txt
index 67e2a0a..1e48bbb 100644
--- a/Documentation/devicetree/bindings/serial/sirf-uart.txt
+++ b/Documentation/devicetree/bindings/serial/sirf-uart.txt
@@ -9,9 +9,9 @@
 - clocks : Should contain uart clock number
 
 Optional properties:
-- sirf,uart-has-rtscts: we have hardware flow controller pins in hardware
-- rts-gpios: RTS pin for USP-based UART if sirf,uart-has-rtscts is true
-- cts-gpios: CTS pin for USP-based UART if sirf,uart-has-rtscts is true
+- uart-has-rtscts: we have hardware flow controller pins in hardware
+- rts-gpios: RTS pin for USP-based UART if uart-has-rtscts is true
+- cts-gpios: CTS pin for USP-based UART if uart-has-rtscts is true
 
 Example:
 
@@ -28,7 +28,7 @@
 
 usp@b0090000 {
 	compatible = "sirf,prima2-usp-uart";
-	sirf,uart-has-rtscts;
+	uart-has-rtscts;
 	rts-gpios = <&gpio 15 0>;
 	cts-gpios = <&gpio 46 0>;
 };
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 4e76a34..82b42c9 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -1054,6 +1054,12 @@
 			the driver will use only 32-bit accessors to read/write
 			the device registers.
 
+		meson,<addr>
+			Start an early, polled-mode console on a meson serial
+			port at the specified address. The serial port must
+			already be setup and configured. Options are not yet
+			supported.
+
 		msm_serial,<addr>
 			Start an early, polled-mode console on an msm serial
 			port at the specified address. The serial port
diff --git a/Documentation/serial/tty.txt b/Documentation/serial/tty.txt
index 798cba8..b487809 100644
--- a/Documentation/serial/tty.txt
+++ b/Documentation/serial/tty.txt
@@ -210,9 +210,6 @@
 
 TTY_OTHER_CLOSED	Device is a pty and the other side has closed.
 
-TTY_OTHER_DONE		Device is a pty and the other side has closed and
-			all pending input processing has been completed.
-
 TTY_NO_WRITE_SPLIT	Prevent driver from splitting up writes into
 			smaller chunks.
 
diff --git a/MAINTAINERS b/MAINTAINERS
index e840831..832f070 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -175,7 +175,6 @@
 8250/16?50 (AND CLONE UARTS) SERIAL DRIVER
 M:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 L:	linux-serial@vger.kernel.org
-W:	http://serial.sourceforge.net
 S:	Maintained
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty.git
 F:	drivers/tty/serial/8250*
diff --git a/arch/ia64/hp/sim/simserial.c b/arch/ia64/hp/sim/simserial.c
index e70cade..21fd50d 100644
--- a/arch/ia64/hp/sim/simserial.c
+++ b/arch/ia64/hp/sim/simserial.c
@@ -300,7 +300,7 @@
 	if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
 	    (cmd != TIOCSERCONFIG) && (cmd != TIOCSERGSTRUCT) &&
 	    (cmd != TIOCMIWAIT)) {
-		if (tty->flags & (1 << TTY_IO_ERROR))
+		if (tty_io_error(tty))
 		    return -EIO;
 	}
 
diff --git a/arch/mips/ath79/early_printk.c b/arch/mips/ath79/early_printk.c
index b955faf..d1adc59 100644
--- a/arch/mips/ath79/early_printk.c
+++ b/arch/mips/ath79/early_printk.c
@@ -31,13 +31,15 @@
 	} while (1);
 }
 
+#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
+
 static void prom_putchar_ar71xx(unsigned char ch)
 {
 	void __iomem *base = (void __iomem *)(KSEG1ADDR(AR71XX_UART_BASE));
 
-	prom_putchar_wait(base + UART_LSR * 4, UART_LSR_THRE, UART_LSR_THRE);
+	prom_putchar_wait(base + UART_LSR * 4, BOTH_EMPTY, BOTH_EMPTY);
 	__raw_writel(ch, base + UART_TX * 4);
-	prom_putchar_wait(base + UART_LSR * 4, UART_LSR_THRE, UART_LSR_THRE);
+	prom_putchar_wait(base + UART_LSR * 4, BOTH_EMPTY, BOTH_EMPTY);
 }
 
 static void prom_putchar_ar933x(unsigned char ch)
diff --git a/drivers/char/pcmcia/synclink_cs.c b/drivers/char/pcmcia/synclink_cs.c
index e524e83..d28922d 100644
--- a/drivers/char/pcmcia/synclink_cs.c
+++ b/drivers/char/pcmcia/synclink_cs.c
@@ -1101,7 +1101,7 @@
 	wake_up_interruptible(&info->status_event_wait_q);
 	wake_up_interruptible(&info->event_wait_q);
 
-	if (info->port.flags & ASYNC_CHECK_CD) {
+	if (tty_port_check_carrier(&info->port)) {
 		if (debug_level >= DEBUG_LEVEL_ISR)
 			printk("%s CD now %s...", info->device_name,
 			       (info->serial_signals & SerialSignal_DCD) ? "on" : "off");
@@ -1272,7 +1272,7 @@
 	if (debug_level >= DEBUG_LEVEL_INFO)
 		printk("%s(%d):startup(%s)\n", __FILE__, __LINE__, info->device_name);
 
-	if (info->port.flags & ASYNC_INITIALIZED)
+	if (tty_port_initialized(&info->port))
 		return 0;
 
 	if (!info->tx_buf) {
@@ -1311,7 +1311,7 @@
 	if (tty)
 		clear_bit(TTY_IO_ERROR, &tty->flags);
 
-	info->port.flags |= ASYNC_INITIALIZED;
+	tty_port_set_initialized(&info->port, 1);
 
 	return 0;
 }
@@ -1322,7 +1322,7 @@
 {
 	unsigned long flags;
 
-	if (!(info->port.flags & ASYNC_INITIALIZED))
+	if (!tty_port_initialized(&info->port))
 		return;
 
 	if (debug_level >= DEBUG_LEVEL_INFO)
@@ -1361,7 +1361,7 @@
 	if (tty)
 		set_bit(TTY_IO_ERROR, &tty->flags);
 
-	info->port.flags &= ~ASYNC_INITIALIZED;
+	tty_port_set_initialized(&info->port, 0);
 }
 
 static void mgslpc_program_hw(MGSLPC_INFO *info, struct tty_struct *tty)
@@ -1466,15 +1466,8 @@
 	}
 	info->timeout += HZ/50;		/* Add .02 seconds of slop */
 
-	if (cflag & CRTSCTS)
-		info->port.flags |= ASYNC_CTS_FLOW;
-	else
-		info->port.flags &= ~ASYNC_CTS_FLOW;
-
-	if (cflag & CLOCAL)
-		info->port.flags &= ~ASYNC_CHECK_CD;
-	else
-		info->port.flags |= ASYNC_CHECK_CD;
+	tty_port_set_cts_flow(&info->port, cflag & CRTSCTS);
+	tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
 
 	/* process tty input control flags */
 
@@ -2246,7 +2239,7 @@
 
 	if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
 	    (cmd != TIOCMIWAIT)) {
-		if (tty->flags & (1 << TTY_IO_ERROR))
+		if (tty_io_error(tty))
 		    return -EIO;
 	}
 
@@ -2316,7 +2309,7 @@
 	/* Handle transition away from B0 status */
 	if (!(old_termios->c_cflag & CBAUD) && C_BAUD(tty)) {
 		info->serial_signals |= SerialSignal_DTR;
-		if (!C_CRTSCTS(tty) || !test_bit(TTY_THROTTLED, &tty->flags))
+		if (!C_CRTSCTS(tty) || !tty_throttled(tty))
 			info->serial_signals |= SerialSignal_RTS;
 		spin_lock_irqsave(&info->lock, flags);
 		set_signals(info);
@@ -2345,7 +2338,7 @@
 	if (tty_port_close_start(port, tty, filp) == 0)
 		goto cleanup;
 
-	if (port->flags & ASYNC_INITIALIZED)
+	if (tty_port_initialized(port))
 		mgslpc_wait_until_sent(tty, info->timeout);
 
 	mgslpc_flush_buffer(tty);
@@ -2378,7 +2371,7 @@
 	if (mgslpc_paranoia_check(info, tty->name, "mgslpc_wait_until_sent"))
 		return;
 
-	if (!(info->port.flags & ASYNC_INITIALIZED))
+	if (!tty_port_initialized(&info->port))
 		goto exit;
 
 	orig_jiffies = jiffies;
diff --git a/drivers/ipack/devices/ipoctal.c b/drivers/ipack/devices/ipoctal.c
index 035d544..75dd15d 100644
--- a/drivers/ipack/devices/ipoctal.c
+++ b/drivers/ipack/devices/ipoctal.c
@@ -629,8 +629,7 @@
 	tty_port_hangup(&channel->tty_port);
 
 	ipoctal_reset_channel(channel);
-
-	clear_bit(ASYNCB_INITIALIZED, &channel->tty_port.flags);
+	tty_port_set_initialized(&channel->tty_port, 0);
 	wake_up_interruptible(&channel->tty_port.open_wait);
 }
 
@@ -642,7 +641,7 @@
 		return;
 
 	ipoctal_reset_channel(channel);
-	clear_bit(ASYNCB_INITIALIZED, &channel->tty_port.flags);
+	tty_port_set_initialized(&channel->tty_port, 0);
 }
 
 static void ipoctal_cleanup(struct tty_struct *tty)
diff --git a/drivers/isdn/i4l/isdn_tty.c b/drivers/isdn/i4l/isdn_tty.c
index 947d5c9..63eaa0a 100644
--- a/drivers/isdn/i4l/isdn_tty.c
+++ b/drivers/isdn/i4l/isdn_tty.c
@@ -1043,17 +1043,13 @@
 	if (!(cflag & PARODD))
 		cval |= UART_LCR_EPAR;
 
-	if (cflag & CLOCAL)
-		port->flags &= ~ASYNC_CHECK_CD;
-	else {
-		port->flags |= ASYNC_CHECK_CD;
-	}
+	tty_port_set_check_carrier(port, ~cflag & CLOCAL);
 }
 
 static int
 isdn_tty_startup(modem_info *info)
 {
-	if (info->port.flags & ASYNC_INITIALIZED)
+	if (tty_port_initialized(&info->port))
 		return 0;
 	isdn_lock_drivers();
 #ifdef ISDN_DEBUG_MODEM_OPEN
@@ -1070,7 +1066,7 @@
 	 */
 	isdn_tty_change_speed(info);
 
-	info->port.flags |= ASYNC_INITIALIZED;
+	tty_port_set_initialized(&info->port, 1);
 	info->msr |= (UART_MSR_DSR | UART_MSR_CTS);
 	info->send_outstanding = 0;
 	return 0;
@@ -1083,7 +1079,7 @@
 static void
 isdn_tty_shutdown(modem_info *info)
 {
-	if (!(info->port.flags & ASYNC_INITIALIZED))
+	if (!tty_port_initialized(&info->port))
 		return;
 #ifdef ISDN_DEBUG_MODEM_OPEN
 	printk(KERN_DEBUG "Shutting down isdnmodem port %d ....\n", info->line);
@@ -1103,7 +1099,7 @@
 	if (info->port.tty)
 		set_bit(TTY_IO_ERROR, &info->port.tty->flags);
 
-	info->port.flags &= ~ASYNC_INITIALIZED;
+	tty_port_set_initialized(&info->port, 0);
 }
 
 /* isdn_tty_write() is the main send-routine. It is called from the upper
@@ -1351,7 +1347,7 @@
 
 	if (isdn_tty_paranoia_check(info, tty->name, __func__))
 		return -ENODEV;
-	if (tty->flags & (1 << TTY_IO_ERROR))
+	if (tty_io_error(tty))
 		return -EIO;
 
 	mutex_lock(&modem_info_mutex);
@@ -1378,7 +1374,7 @@
 
 	if (isdn_tty_paranoia_check(info, tty->name, __func__))
 		return -ENODEV;
-	if (tty->flags & (1 << TTY_IO_ERROR))
+	if (tty_io_error(tty))
 		return -EIO;
 
 #ifdef ISDN_DEBUG_MODEM_IOCTL
@@ -1419,7 +1415,7 @@
 
 	if (isdn_tty_paranoia_check(info, tty->name, "isdn_tty_ioctl"))
 		return -ENODEV;
-	if (tty->flags & (1 << TTY_IO_ERROR))
+	if (tty_io_error(tty))
 		return -EIO;
 	switch (cmd) {
 	case TCSBRK:   /* SVID version: non-zero arg --> no break */
@@ -1581,7 +1577,7 @@
 	 * interrupt driver to stop checking the data ready bit in the
 	 * line status register.
 	 */
-	if (port->flags & ASYNC_INITIALIZED) {
+	if (tty_port_initialized(port)) {
 		tty_wait_until_sent(tty, 3000);	/* 30 seconds timeout */
 		/*
 		 * Before we drop DTR, make sure the UART transmitter
@@ -1622,7 +1618,7 @@
 		return;
 	isdn_tty_shutdown(info);
 	port->count = 0;
-	port->flags &= ~ASYNC_NORMAL_ACTIVE;
+	tty_port_set_active(port, 0);
 	port->tty = NULL;
 	wake_up_interruptible(&port->open_wait);
 }
@@ -1979,7 +1975,7 @@
 #endif
 			if (
 #ifndef FIX_FILE_TRANSFER
-				(info->port.flags & ASYNC_NORMAL_ACTIVE) &&
+			    tty_port_active(&info->port) &&
 #endif
 				(info->isdn_driver == -1) &&
 				(info->isdn_channel == -1) &&
@@ -2018,8 +2014,6 @@
 	return (wret == 2) ? 3 : 0;
 }
 
-#define TTY_IS_ACTIVE(info)	(info->port.flags & ASYNC_NORMAL_ACTIVE)
-
 int
 isdn_tty_stat_callback(int i, isdn_ctrl *c)
 {
@@ -2077,7 +2071,7 @@
 #ifdef ISDN_TTY_STAT_DEBUG
 			printk(KERN_DEBUG "tty_STAT_DCONN ttyI%d\n", info->line);
 #endif
-			if (TTY_IS_ACTIVE(info)) {
+			if (tty_port_active(&info->port)) {
 				if (info->dialing == 1) {
 					info->dialing = 2;
 					return 1;
@@ -2088,7 +2082,7 @@
 #ifdef ISDN_TTY_STAT_DEBUG
 			printk(KERN_DEBUG "tty_STAT_DHUP ttyI%d\n", info->line);
 #endif
-			if (TTY_IS_ACTIVE(info)) {
+			if (tty_port_active(&info->port)) {
 				if (info->dialing == 1)
 					isdn_tty_modem_result(RESULT_BUSY, info);
 				if (info->dialing > 1)
@@ -2118,7 +2112,7 @@
 			 * waiting for it and
 			 * set DCD-bit of its modem-status.
 			 */
-			if (TTY_IS_ACTIVE(info) ||
+			if (tty_port_active(&info->port) ||
 			    (info->port.blocked_open &&
 			     (info->emu.mdmreg[REG_DCD] & BIT_DCD))) {
 				info->msr |= UART_MSR_DCD;
@@ -2145,7 +2139,7 @@
 #ifdef ISDN_TTY_STAT_DEBUG
 			printk(KERN_DEBUG "tty_STAT_BHUP ttyI%d\n", info->line);
 #endif
-			if (TTY_IS_ACTIVE(info)) {
+			if (tty_port_active(&info->port)) {
 #ifdef ISDN_DEBUG_MODEM_HUP
 				printk(KERN_DEBUG "Mhup in ISDN_STAT_BHUP\n");
 #endif
@@ -2157,7 +2151,7 @@
 #ifdef ISDN_TTY_STAT_DEBUG
 			printk(KERN_DEBUG "tty_STAT_NODCH ttyI%d\n", info->line);
 #endif
-			if (TTY_IS_ACTIVE(info)) {
+			if (tty_port_active(&info->port)) {
 				if (info->dialing) {
 					info->dialing = 0;
 					info->last_l2 = -1;
@@ -2183,14 +2177,14 @@
 			return 1;
 #ifdef CONFIG_ISDN_TTY_FAX
 		case ISDN_STAT_FAXIND:
-			if (TTY_IS_ACTIVE(info)) {
+			if (tty_port_active(&info->port)) {
 				isdn_tty_fax_command(info, c);
 			}
 			break;
 #endif
 #ifdef CONFIG_ISDN_AUDIO
 		case ISDN_STAT_AUDIO:
-			if (TTY_IS_ACTIVE(info)) {
+			if (tty_port_active(&info->port)) {
 				switch (c->parm.num[0]) {
 				case ISDN_AUDIO_DTMF:
 					if (info->vonline) {
@@ -2528,7 +2522,7 @@
 		if (info->closing || (!info->port.tty))
 			return;
 
-		if (info->port.flags & ASYNC_CHECK_CD)
+		if (tty_port_check_carrier(&info->port))
 			tty_hangup(info->port.tty);
 	}
 }
diff --git a/drivers/mmc/card/sdio_uart.c b/drivers/mmc/card/sdio_uart.c
index 5415056..5af6fb9 100644
--- a/drivers/mmc/card/sdio_uart.c
+++ b/drivers/mmc/card/sdio_uart.c
@@ -895,7 +895,7 @@
 	/* Handle transition away from B0 status */
 	if (!(old_termios->c_cflag & CBAUD) && (cflag & CBAUD)) {
 		unsigned int mask = TIOCM_DTR;
-		if (!(cflag & CRTSCTS) || !test_bit(TTY_THROTTLED, &tty->flags))
+		if (!(cflag & CRTSCTS) || !tty_throttled(tty))
 			mask |= TIOCM_RTS;
 		sdio_uart_set_mctrl(port, mask);
 	}
diff --git a/drivers/net/usb/hso.c b/drivers/net/usb/hso.c
index 111d907..4b44586 100644
--- a/drivers/net/usb/hso.c
+++ b/drivers/net/usb/hso.c
@@ -2029,7 +2029,7 @@
 
 	tty = tty_port_tty_get(&serial->port);
 
-	if (tty && test_bit(TTY_THROTTLED, &tty->flags)) {
+	if (tty && tty_throttled(tty)) {
 		tty_kref_put(tty);
 		return -1;
 	}
diff --git a/drivers/s390/char/con3215.c b/drivers/s390/char/con3215.c
index e7e078b..931d10e 100644
--- a/drivers/s390/char/con3215.c
+++ b/drivers/s390/char/con3215.c
@@ -289,7 +289,7 @@
 
 	spin_lock_irqsave(get_ccwdev_lock(raw->cdev), flags);
 	raw->flags &= ~RAW3215_TIMER_RUNS;
-	if (!(raw->port.flags & ASYNC_SUSPENDED)) {
+	if (!tty_port_suspended(&raw->port)) {
 		raw3215_mk_write_req(raw);
 		raw3215_start_io(raw);
 		if ((raw->queued_read || raw->queued_write) &&
@@ -311,8 +311,7 @@
  */
 static inline void raw3215_try_io(struct raw3215_info *raw)
 {
-	if (!(raw->port.flags & ASYNC_INITIALIZED) ||
-			(raw->port.flags & ASYNC_SUSPENDED))
+	if (!tty_port_initialized(&raw->port) || tty_port_suspended(&raw->port))
 		return;
 	if (raw->queued_read != NULL)
 		raw3215_start_io(raw);
@@ -494,7 +493,7 @@
 		/* While console is frozen for suspend we have no other
 		 * choice but to drop message from the buffer to make
 		 * room for even more messages. */
-		if (raw->port.flags & ASYNC_SUSPENDED) {
+		if (tty_port_suspended(&raw->port)) {
 			raw3215_drop_line(raw);
 			continue;
 		}
@@ -616,10 +615,10 @@
 {
 	unsigned long flags;
 
-	if (raw->port.flags & ASYNC_INITIALIZED)
+	if (tty_port_initialized(&raw->port))
 		return 0;
 	raw->line_pos = 0;
-	raw->port.flags |= ASYNC_INITIALIZED;
+	tty_port_set_initialized(&raw->port, 1);
 	spin_lock_irqsave(get_ccwdev_lock(raw->cdev), flags);
 	raw3215_try_io(raw);
 	spin_unlock_irqrestore(get_ccwdev_lock(raw->cdev), flags);
@@ -635,8 +634,7 @@
 	DECLARE_WAITQUEUE(wait, current);
 	unsigned long flags;
 
-	if (!(raw->port.flags & ASYNC_INITIALIZED) ||
-	    (raw->flags & RAW3215_FIXED))
+	if (!tty_port_initialized(&raw->port) || (raw->flags & RAW3215_FIXED))
 		return;
 	/* Wait for outstanding requests, then free irq */
 	spin_lock_irqsave(get_ccwdev_lock(raw->cdev), flags);
@@ -650,7 +648,7 @@
 		spin_lock_irqsave(get_ccwdev_lock(raw->cdev), flags);
 		remove_wait_queue(&raw->empty_wait, &wait);
 		set_current_state(TASK_RUNNING);
-		raw->port.flags &= ~ASYNC_INITIALIZED;
+		tty_port_set_initialized(&raw->port, 1);
 	}
 	spin_unlock_irqrestore(get_ccwdev_lock(raw->cdev), flags);
 }
@@ -773,7 +771,7 @@
 	raw = dev_get_drvdata(&cdev->dev);
 	spin_lock_irqsave(get_ccwdev_lock(raw->cdev), flags);
 	raw3215_make_room(raw, RAW3215_BUFFER_SIZE);
-	raw->port.flags |= ASYNC_SUSPENDED;
+	tty_port_set_suspended(&raw->port, 1);
 	spin_unlock_irqrestore(get_ccwdev_lock(raw->cdev), flags);
 	return 0;
 }
@@ -786,7 +784,7 @@
 	/* Allow I/O again and flush output buffer. */
 	raw = dev_get_drvdata(&cdev->dev);
 	spin_lock_irqsave(get_ccwdev_lock(raw->cdev), flags);
-	raw->port.flags &= ~ASYNC_SUSPENDED;
+	tty_port_set_suspended(&raw->port, 0);
 	raw->flags |= RAW3215_FLUSHING;
 	raw3215_try_io(raw);
 	raw->flags &= ~RAW3215_FLUSHING;
@@ -859,7 +857,7 @@
 	unsigned long flags;
 
 	raw = raw3215[0];  /* console 3215 is the first one */
-	if (raw->port.flags & ASYNC_SUSPENDED)
+	if (tty_port_suspended(&raw->port))
 		/* The console is still frozen for suspend. */
 		if (ccw_device_force_console(raw->cdev))
 			/* Forcing didn't work, no panic message .. */
diff --git a/drivers/s390/char/tty3270.c b/drivers/s390/char/tty3270.c
index 0a9f219..272cb6c 100644
--- a/drivers/s390/char/tty3270.c
+++ b/drivers/s390/char/tty3270.c
@@ -1860,7 +1860,7 @@
 	tp = tty->driver_data;
 	if (!tp)
 		return -ENODEV;
-	if (tty->flags & (1 << TTY_IO_ERROR))
+	if (tty_io_error(tty))
 		return -EIO;
 	return kbd_ioctl(tp->kbd, cmd, arg);
 }
@@ -1874,7 +1874,7 @@
 	tp = tty->driver_data;
 	if (!tp)
 		return -ENODEV;
-	if (tty->flags & (1 << TTY_IO_ERROR))
+	if (tty_io_error(tty))
 		return -EIO;
 	return kbd_ioctl(tp->kbd, cmd, (unsigned long)compat_ptr(arg));
 }
diff --git a/drivers/staging/dgnc/dgnc_tty.c b/drivers/staging/dgnc/dgnc_tty.c
index bcd2bdf..5c22159 100644
--- a/drivers/staging/dgnc/dgnc_tty.c
+++ b/drivers/staging/dgnc/dgnc_tty.c
@@ -1255,7 +1255,7 @@
 			if (file->f_flags & O_NONBLOCK)
 				break;
 
-			if (tty->flags & (1 << TTY_IO_ERROR)) {
+			if (tty_io_error(tty)) {
 				retval = -EIO;
 				break;
 			}
diff --git a/drivers/staging/fwserial/fwserial.c b/drivers/staging/fwserial/fwserial.c
index 9b23b5c..1f9389d 100644
--- a/drivers/staging/fwserial/fwserial.c
+++ b/drivers/staging/fwserial/fwserial.c
@@ -1305,7 +1305,7 @@
 	if ((baud == 0) && (old->c_cflag & CBAUD)) {
 		port->mctrl &= ~(TIOCM_DTR | TIOCM_RTS);
 	} else if ((baud != 0) && !(old->c_cflag & CBAUD)) {
-		if (C_CRTSCTS(tty) || !test_bit(TTY_THROTTLED, &tty->flags))
+		if (C_CRTSCTS(tty) || !tty_throttled(tty))
 			port->mctrl |= TIOCM_DTR | TIOCM_RTS;
 		else
 			port->mctrl |= TIOCM_DTR;
diff --git a/drivers/staging/speakup/selection.c b/drivers/staging/speakup/selection.c
index 41ef099..0149edc 100644
--- a/drivers/staging/speakup/selection.c
+++ b/drivers/staging/speakup/selection.c
@@ -150,7 +150,7 @@
 	add_wait_queue(&vc->paste_wait, &wait);
 	while (sel_buffer && sel_buffer_lth > pasted) {
 		set_current_state(TASK_INTERRUPTIBLE);
-		if (test_bit(TTY_THROTTLED, &tty->flags)) {
+		if (tty_throttled(tty)) {
 			schedule();
 			continue;
 		}
diff --git a/drivers/tty/amiserial.c b/drivers/tty/amiserial.c
index eacf4c9..208f573 100644
--- a/drivers/tty/amiserial.c
+++ b/drivers/tty/amiserial.c
@@ -398,7 +398,7 @@
 		wake_up_interruptible(&port->delta_msr_wait);
 	}
 
-	if ((port->flags & ASYNC_CHECK_CD) && (dstatus & SER_DCD)) {
+	if (tty_port_check_carrier(port) && (dstatus & SER_DCD)) {
 #if (defined(SERIAL_DEBUG_OPEN) || defined(SERIAL_DEBUG_INTR))
 		printk("ttyS%d CD now %s...", info->line,
 		       (!(status & SER_DCD)) ? "on" : "off");
@@ -525,7 +525,7 @@
 
 	local_irq_save(flags);
 
-	if (port->flags & ASYNC_INITIALIZED) {
+	if (tty_port_initialized(port)) {
 		free_page(page);
 		goto errout;
 	}
@@ -586,7 +586,7 @@
 	 */
 	change_speed(tty, info, NULL);
 
-	port->flags |= ASYNC_INITIALIZED;
+	tty_port_set_initialized(port, 1);
 	local_irq_restore(flags);
 	return 0;
 
@@ -604,7 +604,7 @@
 	unsigned long	flags;
 	struct serial_state *state;
 
-	if (!(info->tport.flags & ASYNC_INITIALIZED))
+	if (!tty_port_initialized(&info->tport))
 		return;
 
 	state = info;
@@ -645,7 +645,7 @@
 
 	set_bit(TTY_IO_ERROR, &tty->flags);
 
-	info->tport.flags &= ~ASYNC_INITIALIZED;
+	tty_port_set_initialized(&info->tport, 0);
 	local_irq_restore(flags);
 }
 
@@ -727,17 +727,12 @@
 	info->IER &= ~UART_IER_MSI;
 	if (port->flags & ASYNC_HARDPPS_CD)
 		info->IER |= UART_IER_MSI;
-	if (cflag & CRTSCTS) {
-		port->flags |= ASYNC_CTS_FLOW;
+	tty_port_set_cts_flow(port, cflag & CRTSCTS);
+	if (cflag & CRTSCTS)
 		info->IER |= UART_IER_MSI;
-	} else
-		port->flags &= ~ASYNC_CTS_FLOW;
-	if (cflag & CLOCAL)
-		port->flags &= ~ASYNC_CHECK_CD;
-	else {
-		port->flags |= ASYNC_CHECK_CD;
+	tty_port_set_check_carrier(port, ~cflag & CLOCAL);
+	if (~cflag & CLOCAL)
 		info->IER |= UART_IER_MSI;
-	}
 	/* TBD:
 	 * Does clearing IER_MSI imply that we should disable the VBL interrupt ?
 	 */
@@ -1089,7 +1084,7 @@
 	port->low_latency = (port->flags & ASYNC_LOW_LATENCY) ? 1 : 0;
 
 check_and_exit:
-	if (port->flags & ASYNC_INITIALIZED) {
+	if (tty_port_initialized(port)) {
 		if (change_spd) {
 			if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI)
 				tty->alt_speed = 57600;
@@ -1143,7 +1138,7 @@
 
 	if (serial_paranoia_check(info, tty->name, "rs_ioctl"))
 		return -ENODEV;
-	if (tty->flags & (1 << TTY_IO_ERROR))
+	if (tty_io_error(tty))
 		return -EIO;
 
 	control = info->MCR;
@@ -1165,7 +1160,7 @@
 
 	if (serial_paranoia_check(info, tty->name, "rs_ioctl"))
 		return -ENODEV;
-	if (tty->flags & (1 << TTY_IO_ERROR))
+	if (tty_io_error(tty))
 		return -EIO;
 
 	local_irq_save(flags);
@@ -1250,7 +1245,7 @@
 	if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
 	    (cmd != TIOCSERCONFIG) && (cmd != TIOCSERGSTRUCT) &&
 	    (cmd != TIOCMIWAIT) && (cmd != TIOCGICOUNT)) {
-		if (tty->flags & (1 << TTY_IO_ERROR))
+		if (tty_io_error(tty))
 		    return -EIO;
 	}
 
@@ -1342,7 +1337,7 @@
 	/* Handle transition away from B0 status */
 	if (!(old_termios->c_cflag & CBAUD) && (cflag & CBAUD)) {
 		info->MCR |= SER_DTR;
-		if (!C_CRTSCTS(tty) || !test_bit(TTY_THROTTLED, &tty->flags))
+		if (!C_CRTSCTS(tty) || !tty_throttled(tty))
 			info->MCR |= SER_RTS;
 		local_irq_save(flags);
 		rtsdtr_ctrl(info->MCR);
@@ -1395,7 +1390,7 @@
 	 * line status register.
 	 */
 	state->read_status_mask &= ~UART_LSR_DR;
-	if (port->flags & ASYNC_INITIALIZED) {
+	if (tty_port_initialized(port)) {
 	        /* disable receive interrupts */
 	        custom.intena = IF_RBF;
 		mb();
@@ -1495,7 +1490,7 @@
 	rs_flush_buffer(tty);
 	shutdown(tty, info);
 	info->tport.count = 0;
-	info->tport.flags &= ~ASYNC_NORMAL_ACTIVE;
+	tty_port_set_active(&info->tport, 0);
 	info->tport.tty = NULL;
 	wake_up_interruptible(&info->tport.open_wait);
 }
@@ -1543,7 +1538,7 @@
 
 	local_irq_save(flags);
 	status = ciab.pra;
-	control = (state->tport.flags & ASYNC_INITIALIZED) ? state->MCR : status;
+	control = tty_port_initialized(&state->tport) ? state->MCR : status;
 	local_irq_restore(flags);
 
 	stat_buf[0] = 0;
diff --git a/drivers/tty/cyclades.c b/drivers/tty/cyclades.c
index d67e542..3840d6b 100644
--- a/drivers/tty/cyclades.c
+++ b/drivers/tty/cyclades.c
@@ -714,7 +714,7 @@
 		wake_up_interruptible(&info->port.delta_msr_wait);
 	}
 
-	if ((mdm_change & CyDCD) && (info->port.flags & ASYNC_CHECK_CD)) {
+	if ((mdm_change & CyDCD) && tty_port_check_carrier(&info->port)) {
 		if (mdm_status & CyDCD)
 			wake_up_interruptible(&info->port.open_wait);
 		else
@@ -1119,7 +1119,7 @@
 		case C_CM_MDCD:
 			info->icount.dcd++;
 			delta_count++;
-			if (info->port.flags & ASYNC_CHECK_CD) {
+			if (tty_port_check_carrier(&info->port)) {
 				u32 dcd = fw_ver > 241 ? param :
 					readl(&info->u.cyz.ch_ctrl->rs_status);
 				if (dcd & C_RS_DCD)
@@ -1279,7 +1279,7 @@
 
 	spin_lock_irqsave(&card->card_lock, flags);
 
-	if (info->port.flags & ASYNC_INITIALIZED)
+	if (tty_port_initialized(&info->port))
 		goto errout;
 
 	if (!info->type) {
@@ -1364,7 +1364,7 @@
 		/* enable send, recv, modem !!! */
 	}
 
-	info->port.flags |= ASYNC_INITIALIZED;
+	tty_port_set_initialized(&info->port, 1);
 
 	clear_bit(TTY_IO_ERROR, &tty->flags);
 	info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
@@ -1424,7 +1424,7 @@
 	struct cyclades_card *card;
 	unsigned long flags;
 
-	if (!(info->port.flags & ASYNC_INITIALIZED))
+	if (!tty_port_initialized(&info->port))
 		return;
 
 	card = info->card;
@@ -1448,7 +1448,7 @@
 		   some later date (after testing)!!! */
 
 		set_bit(TTY_IO_ERROR, &tty->flags);
-		info->port.flags &= ~ASYNC_INITIALIZED;
+		tty_port_set_initialized(&info->port, 0);
 		spin_unlock_irqrestore(&card->card_lock, flags);
 	} else {
 #ifdef CY_DEBUG_OPEN
@@ -1473,7 +1473,7 @@
 			tty_port_lower_dtr_rts(&info->port);
 
 		set_bit(TTY_IO_ERROR, &tty->flags);
-		info->port.flags &= ~ASYNC_INITIALIZED;
+		tty_port_set_initialized(&info->port, 0);
 
 		spin_unlock_irqrestore(&card->card_lock, flags);
 	}
@@ -1711,7 +1711,7 @@
 		/* Stop accepting input */
 		cyy_writeb(info, CyCAR, channel & 0x03);
 		cyy_writeb(info, CySRER, cyy_readb(info, CySRER) & ~CyRxData);
-		if (info->port.flags & ASYNC_INITIALIZED) {
+		if (tty_port_initialized(&info->port)) {
 			/* Waiting for on-board buffers to be empty before
 			   closing the port */
 			spin_unlock_irqrestore(&card->card_lock, flags);
@@ -2083,17 +2083,12 @@
 			info->cor1 |= CyPARITY_NONE;
 
 		/* CTS flow control flag */
-		if (cflag & CRTSCTS) {
-			info->port.flags |= ASYNC_CTS_FLOW;
+		tty_port_set_cts_flow(&info->port, cflag & CRTSCTS);
+		if (cflag & CRTSCTS)
 			info->cor2 |= CyCtsAE;
-		} else {
-			info->port.flags &= ~ASYNC_CTS_FLOW;
-			info->cor2 &= ~CyCtsAE;
-		}
-		if (cflag & CLOCAL)
-			info->port.flags &= ~ASYNC_CHECK_CD;
 		else
-			info->port.flags |= ASYNC_CHECK_CD;
+			info->cor2 &= ~CyCtsAE;
+		tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
 
 	 /***********************************************
 	    The hardware option, CyRtsAO, presents RTS when
@@ -2234,7 +2229,7 @@
 		}
 		/* As the HW flow control is done in firmware, the driver
 		   doesn't need to care about it */
-		info->port.flags &= ~ASYNC_CTS_FLOW;
+		tty_port_set_cts_flow(&info->port, 0);
 
 		/* XON/XOFF/XANY flow control flags */
 		sw_flow = 0;
@@ -2252,10 +2247,7 @@
 		}
 
 		/* CD sensitivity */
-		if (cflag & CLOCAL)
-			info->port.flags &= ~ASYNC_CHECK_CD;
-		else
-			info->port.flags |= ASYNC_CHECK_CD;
+		tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
 
 		if (baud == 0) {	/* baud rate is zero, turn off line */
 			cy_writel(&ch_ctrl->rs_control,
@@ -2342,7 +2334,7 @@
 	info->port.closing_wait = new_serial.closing_wait * HZ / 100;
 
 check_and_exit:
-	if (info->port.flags & ASYNC_INITIALIZED) {
+	if (tty_port_initialized(&info->port)) {
 		cy_set_line_char(info, tty);
 		ret = 0;
 	} else {
diff --git a/drivers/tty/hvc/hvc_console.c b/drivers/tty/hvc/hvc_console.c
index e46d628..ce86487 100644
--- a/drivers/tty/hvc/hvc_console.c
+++ b/drivers/tty/hvc/hvc_console.c
@@ -632,7 +632,7 @@
 		goto bail;
 
 	/* Now check if we can get data (are we throttled ?) */
-	if (test_bit(TTY_THROTTLED, &tty->flags))
+	if (tty_throttled(tty))
 		goto throttled;
 
 	/* If we aren't notifier driven and aren't throttled, we always
@@ -814,7 +814,7 @@
 
 	n = hp->ops->get_chars(hp->vtermno, &ch, 1);
 
-	if (n == 0)
+	if (n <= 0)
 		return NO_POLL_CHAR;
 
 	return ch;
diff --git a/drivers/tty/hvc/hvcs.c b/drivers/tty/hvc/hvcs.c
index 5997b17..3c4d7c2b 100644
--- a/drivers/tty/hvc/hvcs.c
+++ b/drivers/tty/hvc/hvcs.c
@@ -600,7 +600,7 @@
 
 	hvcs_try_write(hvcsd);
 
-	if (!tty || test_bit(TTY_THROTTLED, &tty->flags)) {
+	if (!tty || tty_throttled(tty)) {
 		hvcsd->todo_mask &= ~(HVCS_READ_MASK);
 		goto bail;
 	} else if (!(hvcsd->todo_mask & (HVCS_READ_MASK)))
diff --git a/drivers/tty/hvc/hvsi.c b/drivers/tty/hvc/hvsi.c
index a75146f..96ce6bd 100644
--- a/drivers/tty/hvc/hvsi.c
+++ b/drivers/tty/hvc/hvsi.c
@@ -509,7 +509,7 @@
 	}
 
 	spin_lock_irqsave(&hp->lock, flags);
-	if (tty && hp->n_throttle && !test_bit(TTY_THROTTLED, &tty->flags)) {
+	if (tty && hp->n_throttle && !tty_throttled(tty)) {
 		/* we weren't hung up and we weren't throttled, so we can
 		 * deliver the rest now */
 		hvsi_send_overflow(hp);
diff --git a/drivers/tty/ipwireless/hardware.c b/drivers/tty/ipwireless/hardware.c
index ad7031a..df0204b 100644
--- a/drivers/tty/ipwireless/hardware.c
+++ b/drivers/tty/ipwireless/hardware.c
@@ -1572,6 +1572,11 @@
 					sizeof(struct ipw_setup_reboot_msg_ack),
 					ADDR_SETUP_PROT, TL_PROTOCOLID_SETUP,
 					TL_SETUP_SIGNO_REBOOT_MSG_ACK);
+			if (!packet) {
+				pr_err(IPWIRELESS_PCCARD_NAME
+				       ": Not enough memory to send reboot packet");
+				break;
+			}
 			packet->header.length =
 				sizeof(struct TlSetupRebootMsgAck);
 			send_packet(hw, PRIO_SETUP, &packet->header);
diff --git a/drivers/tty/isicom.c b/drivers/tty/isicom.c
index 8bf6763..b70187b 100644
--- a/drivers/tty/isicom.c
+++ b/drivers/tty/isicom.c
@@ -438,8 +438,8 @@
 
 	for (; count > 0; count--, port++) {
 		/* port not active or tx disabled to force flow control */
-		if (!(port->port.flags & ASYNC_INITIALIZED) ||
-				!(port->status & ISI_TXOK))
+		if (!tty_port_initialized(&port->port) ||
+			!(port->status & ISI_TXOK))
 			continue;
 
 		txcount = min_t(short, TX_SIZE, port->xmit_cnt);
@@ -553,7 +553,7 @@
 		return IRQ_HANDLED;
 	}
 	port = card->ports + channel;
-	if (!(port->port.flags & ASYNC_INITIALIZED)) {
+	if (!tty_port_initialized(&port->port)) {
 		outw(0x0000, base+0x04); /* enable interrupts */
 		spin_unlock(&card->card_lock);
 		return IRQ_HANDLED;
@@ -577,7 +577,7 @@
 		header = inw(base);
 		switch (header & 0xff) {
 		case 0:	/* Change in EIA signals */
-			if (port->port.flags & ASYNC_CHECK_CD) {
+			if (tty_port_check_carrier(&port->port)) {
 				if (port->status & ISI_DCD) {
 					if (!(header & ISI_DCD)) {
 					/* Carrier has been lost  */
@@ -758,18 +758,13 @@
 		outw(channel_setup, base);
 		InterruptTheCard(base);
 	}
-	if (C_CLOCAL(tty))
-		port->port.flags &= ~ASYNC_CHECK_CD;
-	else
-		port->port.flags |= ASYNC_CHECK_CD;
+	tty_port_set_check_carrier(&port->port, !C_CLOCAL(tty));
 
 	/* flow control settings ...*/
 	flow_ctrl = 0;
-	port->port.flags &= ~ASYNC_CTS_FLOW;
-	if (C_CRTSCTS(tty)) {
-		port->port.flags |= ASYNC_CTS_FLOW;
+	tty_port_set_cts_flow(&port->port, C_CRTSCTS(tty));
+	if (C_CRTSCTS(tty))
 		flow_ctrl |= ISICOM_CTSRTS;
-	}
 	if (I_IXON(tty))
 		flow_ctrl |= ISICOM_RESPOND_XONXOFF;
 	if (I_IXOFF(tty))
diff --git a/drivers/tty/moxa.c b/drivers/tty/moxa.c
index 92982d7..60d37b2 100644
--- a/drivers/tty/moxa.c
+++ b/drivers/tty/moxa.c
@@ -912,7 +912,7 @@
 
 	/* pci hot-un-plug support */
 	for (a = 0; a < brd->numPorts; a++)
-		if (brd->ports[a].port.flags & ASYNC_INITIALIZED)
+		if (tty_port_initialized(&brd->ports[a].port))
 			tty_port_tty_hangup(&brd->ports[a].port, false);
 
 	for (a = 0; a < MAX_PORTS_PER_BOARD; a++)
@@ -921,7 +921,7 @@
 	while (1) {
 		opened = 0;
 		for (a = 0; a < brd->numPorts; a++)
-			if (brd->ports[a].port.flags & ASYNC_INITIALIZED)
+			if (tty_port_initialized(&brd->ports[a].port))
 				opened++;
 		mutex_unlock(&moxa_openlock);
 		if (!opened)
@@ -1192,13 +1192,13 @@
 	tty->driver_data = ch;
 	tty_port_tty_set(&ch->port, tty);
 	mutex_lock(&ch->port.mutex);
-	if (!(ch->port.flags & ASYNC_INITIALIZED)) {
+	if (!tty_port_initialized(&ch->port)) {
 		ch->statusflags = 0;
 		moxa_set_tty_param(tty, &tty->termios);
 		MoxaPortLineCtrl(ch, 1, 1);
 		MoxaPortEnable(ch);
 		MoxaSetFifo(ch, ch->type == PORT_16550A);
-		ch->port.flags |= ASYNC_INITIALIZED;
+		tty_port_set_initialized(&ch->port, 1);
 	}
 	mutex_unlock(&ch->port.mutex);
 	mutex_unlock(&moxa_openlock);
@@ -1379,7 +1379,7 @@
 {
 	struct tty_struct *tty = tty_port_tty_get(&p->port);
 	void __iomem *ofsAddr;
-	unsigned int inited = p->port.flags & ASYNC_INITIALIZED;
+	unsigned int inited = tty_port_initialized(&p->port);
 	u16 intr;
 
 	if (tty) {
@@ -1394,7 +1394,7 @@
 			tty_wakeup(tty);
 		}
 
-		if (inited && !test_bit(TTY_THROTTLED, &tty->flags) &&
+		if (inited && !tty_throttled(tty) &&
 				MoxaPortRxQueue(p) > 0) { /* RX */
 			MoxaPortReadData(p);
 			tty_schedule_flip(&p->port);
diff --git a/drivers/tty/mxser.c b/drivers/tty/mxser.c
index 2f12bb9..98d2bd1 100644
--- a/drivers/tty/mxser.c
+++ b/drivers/tty/mxser.c
@@ -711,8 +711,8 @@
 	/* CTS flow control flag and modem status interrupts */
 	info->IER &= ~UART_IER_MSI;
 	info->MCR &= ~UART_MCR_AFE;
+	tty_port_set_cts_flow(&info->port, cflag & CRTSCTS);
 	if (cflag & CRTSCTS) {
-		info->port.flags |= ASYNC_CTS_FLOW;
 		info->IER |= UART_IER_MSI;
 		if ((info->type == PORT_16550A) || (info->board->chip_flag)) {
 			info->MCR |= UART_MCR_AFE;
@@ -744,16 +744,11 @@
 				}
 			}
 		}
-	} else {
-		info->port.flags &= ~ASYNC_CTS_FLOW;
 	}
 	outb(info->MCR, info->ioaddr + UART_MCR);
-	if (cflag & CLOCAL) {
-		info->port.flags &= ~ASYNC_CHECK_CD;
-	} else {
-		info->port.flags |= ASYNC_CHECK_CD;
+	tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
+	if (~cflag & CLOCAL)
 		info->IER |= UART_IER_MSI;
-	}
 	outb(info->IER, info->ioaddr + UART_IER);
 
 	/*
@@ -826,7 +821,7 @@
 	port->mon_data.modem_status = status;
 	wake_up_interruptible(&port->port.delta_msr_wait);
 
-	if ((port->port.flags & ASYNC_CHECK_CD) && (status & UART_MSR_DDCD)) {
+	if (tty_port_check_carrier(&port->port) && (status & UART_MSR_DDCD)) {
 		if (status & UART_MSR_DCD)
 			wake_up_interruptible(&port->port.open_wait);
 	}
@@ -1086,12 +1081,10 @@
 	mutex_lock(&port->mutex);
 	mxser_close_port(port);
 	mxser_flush_buffer(tty);
-	if (test_bit(ASYNCB_INITIALIZED, &port->flags)) {
-		if (C_HUPCL(tty))
-			tty_port_lower_dtr_rts(port);
-	}
+	if (tty_port_initialized(port) && C_HUPCL(tty))
+		tty_port_lower_dtr_rts(port);
 	mxser_shutdown_port(port);
-	clear_bit(ASYNCB_INITIALIZED, &port->flags);
+	tty_port_set_initialized(port, 0);
 	mutex_unlock(&port->mutex);
 	info->closing = 0;
 	/* Right now the tty_port set is done outside of the close_end helper
@@ -1287,7 +1280,7 @@
 
 	process_txrx_fifo(info);
 
-	if (test_bit(ASYNCB_INITIALIZED, &port->flags)) {
+	if (tty_port_initialized(port)) {
 		if (flags != (port->flags & ASYNC_SPD_MASK)) {
 			spin_lock_irqsave(&info->slock, sl_flags);
 			mxser_change_speed(tty, NULL);
@@ -1296,7 +1289,7 @@
 	} else {
 		retval = mxser_activate(port, tty);
 		if (retval == 0)
-			set_bit(ASYNCB_INITIALIZED, &port->flags);
+			tty_port_set_initialized(port, 1);
 	}
 	return retval;
 }
@@ -1334,7 +1327,7 @@
 
 	if (tty->index == MXSER_PORTS)
 		return -ENOIOCTLCMD;
-	if (test_bit(TTY_IO_ERROR, &tty->flags))
+	if (tty_io_error(tty))
 		return -EIO;
 
 	control = info->MCR;
@@ -1361,7 +1354,7 @@
 
 	if (tty->index == MXSER_PORTS)
 		return -ENOIOCTLCMD;
-	if (test_bit(TTY_IO_ERROR, &tty->flags))
+	if (tty_io_error(tty))
 		return -EIO;
 
 	spin_lock_irqsave(&info->slock, flags);
@@ -1715,8 +1708,7 @@
 		return 0;
 	}
 
-	if (cmd != TIOCGSERIAL && cmd != TIOCMIWAIT &&
-			test_bit(TTY_IO_ERROR, &tty->flags))
+	if (cmd != TIOCGSERIAL && cmd != TIOCMIWAIT && tty_io_error(tty))
 		return -EIO;
 
 	switch (cmd) {
@@ -2257,7 +2249,7 @@
 				iir &= MOXA_MUST_IIR_MASK;
 				tty = tty_port_tty_get(&port->port);
 				if (!tty || port->closing ||
-				    !(port->port.flags & ASYNC_INITIALIZED)) {
+				    !tty_port_initialized(&port->port)) {
 					status = inb(port->ioaddr + UART_LSR);
 					outb(0x27, port->ioaddr + UART_FCR);
 					inb(port->ioaddr + UART_MSR);
@@ -2400,7 +2392,6 @@
 		if (brd->chip_flag != MOXA_OTHER_UART)
 			mxser_enable_must_enchance_mode(info->ioaddr);
 
-		info->port.flags = ASYNC_SHARE_IRQ;
 		info->type = brd->uart_type;
 
 		process_txrx_fifo(info);
diff --git a/drivers/tty/n_gsm.c b/drivers/tty/n_gsm.c
index 0c27a00..54cab59 100644
--- a/drivers/tty/n_gsm.c
+++ b/drivers/tty/n_gsm.c
@@ -2045,7 +2045,9 @@
 		}
 	}
 	spin_unlock(&gsm_mux_lock);
-	WARN_ON(i == MAX_MUX);
+	/* open failed before registering => nothing to do */
+	if (i == MAX_MUX)
+		return;
 
 	/* In theory disconnecting DLCI 0 is sufficient but for some
 	   modems this is apparently not the case. */
@@ -2947,7 +2949,7 @@
 	dlci->modem_rx = 0;
 	/* We could in theory open and close before we wait - eg if we get
 	   a DM straight back. This is ok as that will have caused a hangup */
-	set_bit(ASYNCB_INITIALIZED, &port->flags);
+	tty_port_set_initialized(port, 1);
 	/* Start sending off SABM messages */
 	gsm_dlci_begin_open(dlci);
 	/* And wait for virtual carrier */
@@ -2970,10 +2972,8 @@
 	if (tty_port_close_start(&dlci->port, tty, filp) == 0)
 		return;
 	gsm_dlci_begin_close(dlci);
-	if (test_bit(ASYNCB_INITIALIZED, &dlci->port.flags)) {
-		if (C_HUPCL(tty))
-			tty_port_lower_dtr_rts(&dlci->port);
-	}
+	if (tty_port_initialized(&dlci->port) && C_HUPCL(tty))
+		tty_port_lower_dtr_rts(&dlci->port);
 	tty_port_close_end(&dlci->port, tty);
 	tty_port_tty_set(&dlci->port, NULL);
 	return;
diff --git a/drivers/tty/n_hdlc.c b/drivers/tty/n_hdlc.c
index bcaba17..a7fa016 100644
--- a/drivers/tty/n_hdlc.c
+++ b/drivers/tty/n_hdlc.c
@@ -599,7 +599,7 @@
 	add_wait_queue(&tty->read_wait, &wait);
 
 	for (;;) {
-		if (test_bit(TTY_OTHER_DONE, &tty->flags)) {
+		if (test_bit(TTY_OTHER_CLOSED, &tty->flags)) {
 			ret = -EIO;
 			break;
 		}
@@ -827,7 +827,7 @@
 		/* set bits for operations that won't block */
 		if (n_hdlc->rx_buf_list.head)
 			mask |= POLLIN | POLLRDNORM;	/* readable */
-		if (test_bit(TTY_OTHER_DONE, &tty->flags))
+		if (test_bit(TTY_OTHER_CLOSED, &tty->flags))
 			mask |= POLLHUP;
 		if (tty_hung_up_p(filp))
 			mask |= POLLHUP;
diff --git a/drivers/tty/n_tty.c b/drivers/tty/n_tty.c
index fb76a7d..bdf0e6e 100644
--- a/drivers/tty/n_tty.c
+++ b/drivers/tty/n_tty.c
@@ -1917,18 +1917,6 @@
 		return ldata->commit_head - ldata->read_tail >= amt;
 }
 
-static inline int check_other_done(struct tty_struct *tty)
-{
-	int done = test_bit(TTY_OTHER_DONE, &tty->flags);
-	if (done) {
-		/* paired with cmpxchg() in check_other_closed(); ensures
-		 * read buffer head index is not stale
-		 */
-		smp_mb__after_atomic();
-	}
-	return done;
-}
-
 /**
  *	copy_from_read_buf	-	copy read data directly
  *	@tty: terminal device
@@ -2124,7 +2112,7 @@
 	struct n_tty_data *ldata = tty->disc_data;
 	unsigned char __user *b = buf;
 	DEFINE_WAIT_FUNC(wait, woken_wake_function);
-	int c, done;
+	int c;
 	int minimum, time;
 	ssize_t retval = 0;
 	long timeout;
@@ -2183,32 +2171,35 @@
 			break;
 		}
 
-		done = check_other_done(tty);
-
 		if (!input_available_p(tty, 0)) {
-			if (done) {
-				retval = -EIO;
-				break;
-			}
-			if (tty_hung_up_p(file))
-				break;
-			if (!timeout)
-				break;
-			if (file->f_flags & O_NONBLOCK) {
-				retval = -EAGAIN;
-				break;
-			}
-			if (signal_pending(current)) {
-				retval = -ERESTARTSYS;
-				break;
-			}
 			up_read(&tty->termios_rwsem);
-
-			timeout = wait_woken(&wait, TASK_INTERRUPTIBLE,
-					     timeout);
-
+			tty_buffer_flush_work(tty->port);
 			down_read(&tty->termios_rwsem);
-			continue;
+			if (!input_available_p(tty, 0)) {
+				if (test_bit(TTY_OTHER_CLOSED, &tty->flags)) {
+					retval = -EIO;
+					break;
+				}
+				if (tty_hung_up_p(file))
+					break;
+				if (!timeout)
+					break;
+				if (file->f_flags & O_NONBLOCK) {
+					retval = -EAGAIN;
+					break;
+				}
+				if (signal_pending(current)) {
+					retval = -ERESTARTSYS;
+					break;
+				}
+				up_read(&tty->termios_rwsem);
+
+				timeout = wait_woken(&wait, TASK_INTERRUPTIBLE,
+						timeout);
+
+				down_read(&tty->termios_rwsem);
+				continue;
+			}
 		}
 
 		if (ldata->icanon && !L_EXTPROC(tty)) {
@@ -2386,12 +2377,17 @@
 
 	poll_wait(file, &tty->read_wait, wait);
 	poll_wait(file, &tty->write_wait, wait);
-	if (check_other_done(tty))
-		mask |= POLLHUP;
 	if (input_available_p(tty, 1))
 		mask |= POLLIN | POLLRDNORM;
+	else {
+		tty_buffer_flush_work(tty->port);
+		if (input_available_p(tty, 1))
+			mask |= POLLIN | POLLRDNORM;
+	}
 	if (tty->packet && tty->link->ctrl_status)
 		mask |= POLLPRI | POLLIN | POLLRDNORM;
+	if (test_bit(TTY_OTHER_CLOSED, &tty->flags))
+		mask |= POLLHUP;
 	if (tty_hung_up_p(file))
 		mask |= POLLHUP;
 	if (tty->ops->write && !tty_is_writelocked(tty) &&
diff --git a/drivers/tty/nozomi.c b/drivers/tty/nozomi.c
index 5cc80b8..d6fd0e8 100644
--- a/drivers/tty/nozomi.c
+++ b/drivers/tty/nozomi.c
@@ -826,7 +826,7 @@
 	size = __le32_to_cpu(readl(addr));
 	/*  DBG1( "%d bytes port: %d", size, index); */
 
-	if (tty && test_bit(TTY_THROTTLED, &tty->flags)) {
+	if (tty && tty_throttled(tty)) {
 		DBG1("No room in tty, don't read data, don't ack interrupt, "
 			"disable interrupt");
 
diff --git a/drivers/tty/pty.c b/drivers/tty/pty.c
index cf0dc51..dd4b841 100644
--- a/drivers/tty/pty.c
+++ b/drivers/tty/pty.c
@@ -44,7 +44,7 @@
 	if (tty->driver->subtype == PTY_TYPE_MASTER)
 		WARN_ON(tty->count > 1);
 	else {
-		if (test_bit(TTY_IO_ERROR, &tty->flags))
+		if (tty_io_error(tty))
 			return;
 		if (tty->count > 2)
 			return;
@@ -59,7 +59,7 @@
 	if (!tty->link)
 		return;
 	set_bit(TTY_OTHER_CLOSED, &tty->link->flags);
-	tty_flip_buffer_push(tty->link->port);
+	wake_up_interruptible(&tty->link->read_wait);
 	wake_up_interruptible(&tty->link->write_wait);
 	if (tty->driver->subtype == PTY_TYPE_MASTER) {
 		set_bit(TTY_OTHER_CLOSED, &tty->flags);
@@ -247,9 +247,7 @@
 		goto out;
 
 	clear_bit(TTY_IO_ERROR, &tty->flags);
-	/* TTY_OTHER_CLOSED must be cleared before TTY_OTHER_DONE */
 	clear_bit(TTY_OTHER_CLOSED, &tty->link->flags);
-	clear_bit(TTY_OTHER_DONE, &tty->link->flags);
 	set_bit(TTY_THROTTLED, &tty->flags);
 	return 0;
 
diff --git a/drivers/tty/rocket.c b/drivers/tty/rocket.c
index 0b802cd..b0cc47c 100644
--- a/drivers/tty/rocket.c
+++ b/drivers/tty/rocket.c
@@ -495,7 +495,7 @@
 	if (!info)
 		return;
 
-	if ((info->port.flags & ASYNC_INITIALIZED) == 0) {
+	if (!tty_port_initialized(&info->port)) {
 		printk(KERN_WARNING "rp: WARNING: rp_handle_port called with "
 				"info->flags & NOT_INIT\n");
 		return;
@@ -615,7 +615,8 @@
  *  the board.  
  *  Inputs:  board, aiop, chan numbers
  */
-static void init_r_port(int board, int aiop, int chan, struct pci_dev *pci_dev)
+static void __init
+init_r_port(int board, int aiop, int chan, struct pci_dev *pci_dev)
 {
 	unsigned rocketMode;
 	struct r_port *info;
@@ -920,7 +921,7 @@
 	/*
 	 * Info->count is now 1; so it's safe to sleep now.
 	 */
-	if (!test_bit(ASYNCB_INITIALIZED, &port->flags)) {
+	if (!tty_port_initialized(port)) {
 		cp = &info->channel;
 		sSetRxTrigger(cp, TRIG_1);
 		if (sGetChanStatus(cp) & CD_ACT)
@@ -944,7 +945,7 @@
 		sEnRxFIFO(cp);
 		sEnTransmit(cp);
 
-		set_bit(ASYNCB_INITIALIZED, &info->port.flags);
+		tty_port_set_initialized(&info->port, 1);
 
 		/*
 		 * Set up the tty->alt_speed kludge
@@ -1042,9 +1043,10 @@
 		}
 	}
 	spin_lock_irq(&port->lock);
-	info->port.flags &= ~(ASYNC_INITIALIZED | ASYNC_NORMAL_ACTIVE);
 	tty->closing = 0;
 	spin_unlock_irq(&port->lock);
+	tty_port_set_initialized(port, 0);
+	tty_port_set_active(port, 0);
 	mutex_unlock(&port->mutex);
 	tty_port_tty_set(port, NULL);
 
@@ -1512,7 +1514,7 @@
 	sDisCTSFlowCtl(cp);
 	sDisTxSoftFlowCtl(cp);
 	sClrTxXOFF(cp);
-	clear_bit(ASYNCB_INITIALIZED, &info->port.flags);
+	tty_port_set_initialized(&info->port, 0);
 
 	wake_up_interruptible(&info->port.open_wait);
 }
@@ -1624,7 +1626,7 @@
 	/*  Write remaining data into the port's xmit_buf */
 	while (1) {
 		/* Hung up ? */
-		if (!test_bit(ASYNCB_NORMAL_ACTIVE, &info->port.flags))
+		if (!tty_port_active(&info->port))
 			goto end;
 		c = min(count, XMIT_BUF_SIZE - info->xmit_cnt - 1);
 		c = min(c, XMIT_BUF_SIZE - info->xmit_head);
diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h
index 047a7ba..215a992 100644
--- a/drivers/tty/serial/8250/8250.h
+++ b/drivers/tty/serial/8250/8250.h
@@ -17,7 +17,7 @@
 
 struct uart_8250_dma {
 	int (*tx_dma)(struct uart_8250_port *p);
-	int (*rx_dma)(struct uart_8250_port *p, unsigned int iir);
+	int (*rx_dma)(struct uart_8250_port *p);
 
 	/* Filter function */
 	dma_filter_fn		fn;
@@ -84,7 +84,6 @@
 #define UART_BUG_THRE	(1 << 3)	/* UART has buggy THRE reassertion */
 #define UART_BUG_PARITY	(1 << 4)	/* UART mishandles parity if FIFO enabled */
 
-#define HIGH_BITS_OFFSET ((sizeof(long)-sizeof(int))*8)
 
 #ifdef CONFIG_SERIAL_8250_SHARE_IRQ
 #define SERIAL8250_SHARE_IRQS 1
@@ -151,6 +150,12 @@
 static inline void serial8250_pnp_exit(void) { }
 #endif
 
+#ifdef CONFIG_SERIAL_8250_FINTEK
+int fintek_8250_probe(struct uart_8250_port *uart);
+#else
+static inline int fintek_8250_probe(struct uart_8250_port *uart) { return 0; }
+#endif
+
 #ifdef CONFIG_ARCH_OMAP1
 static inline int is_omap1_8250(struct uart_8250_port *pt)
 {
@@ -190,7 +195,8 @@
 
 #ifdef CONFIG_SERIAL_8250_DMA
 extern int serial8250_tx_dma(struct uart_8250_port *);
-extern int serial8250_rx_dma(struct uart_8250_port *, unsigned int iir);
+extern int serial8250_rx_dma(struct uart_8250_port *);
+extern void serial8250_rx_dma_flush(struct uart_8250_port *);
 extern int serial8250_request_dma(struct uart_8250_port *);
 extern void serial8250_release_dma(struct uart_8250_port *);
 #else
@@ -198,10 +204,11 @@
 {
 	return -1;
 }
-static inline int serial8250_rx_dma(struct uart_8250_port *p, unsigned int iir)
+static inline int serial8250_rx_dma(struct uart_8250_port *p)
 {
 	return -1;
 }
+static inline void serial8250_rx_dma_flush(struct uart_8250_port *p) { }
 static inline int serial8250_request_dma(struct uart_8250_port *p)
 {
 	return -1;
diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c
index 2f4f5ee..0fbd7c0 100644
--- a/drivers/tty/serial/8250/8250_core.c
+++ b/drivers/tty/serial/8250/8250_core.c
@@ -830,6 +830,7 @@
 		uart.port.handle_irq	= p->handle_irq;
 		uart.port.handle_break	= p->handle_break;
 		uart.port.set_termios	= p->set_termios;
+		uart.port.get_mctrl	= p->get_mctrl;
 		uart.port.pm		= p->pm;
 		uart.port.dev		= &dev->dev;
 		uart.port.irqflags	|= irqflag;
@@ -1022,6 +1023,8 @@
 		/*  Possibly override set_termios call */
 		if (up->port.set_termios)
 			uart->port.set_termios = up->port.set_termios;
+		if (up->port.get_mctrl)
+			uart->port.get_mctrl = up->port.get_mctrl;
 		if (up->port.set_mctrl)
 			uart->port.set_mctrl = up->port.set_mctrl;
 		if (up->port.startup)
diff --git a/drivers/tty/serial/8250/8250_dma.c b/drivers/tty/serial/8250/8250_dma.c
index 78259d3..7f33d1c 100644
--- a/drivers/tty/serial/8250/8250_dma.c
+++ b/drivers/tty/serial/8250/8250_dma.c
@@ -110,30 +110,11 @@
 	return ret;
 }
 
-int serial8250_rx_dma(struct uart_8250_port *p, unsigned int iir)
+int serial8250_rx_dma(struct uart_8250_port *p)
 {
 	struct uart_8250_dma		*dma = p->dma;
 	struct dma_async_tx_descriptor	*desc;
 
-	switch (iir & 0x3f) {
-	case UART_IIR_RLSI:
-		/* 8250_core handles errors and break interrupts */
-		return -EIO;
-	case UART_IIR_RX_TIMEOUT:
-		/*
-		 * If RCVR FIFO trigger level was not reached, complete the
-		 * transfer and let 8250_core copy the remaining data.
-		 */
-		if (dma->rx_running) {
-			dmaengine_pause(dma->rxchan);
-			__dma_rx_complete(p);
-			dmaengine_terminate_all(dma->rxchan);
-		}
-		return -ETIMEDOUT;
-	default:
-		break;
-	}
-
 	if (dma->rx_running)
 		return 0;
 
@@ -154,10 +135,23 @@
 	return 0;
 }
 
+void serial8250_rx_dma_flush(struct uart_8250_port *p)
+{
+	struct uart_8250_dma *dma = p->dma;
+
+	if (dma->rx_running) {
+		dmaengine_pause(dma->rxchan);
+		__dma_rx_complete(p);
+		dmaengine_terminate_all(dma->rxchan);
+	}
+}
+
 int serial8250_request_dma(struct uart_8250_port *p)
 {
 	struct uart_8250_dma	*dma = p->dma;
 	dma_cap_mask_t		mask;
+	struct dma_slave_caps	caps;
+	int			ret;
 
 	/* Default slave configuration parameters */
 	dma->rxconf.direction		= DMA_DEV_TO_MEM;
@@ -178,6 +172,16 @@
 	if (!dma->rxchan)
 		return -ENODEV;
 
+	/* 8250 rx dma requires dmaengine driver to support pause/terminate */
+	ret = dma_get_slave_caps(dma->rxchan, &caps);
+	if (ret)
+		goto release_rx;
+	if (!caps.cmd_pause || !caps.cmd_terminate ||
+	    caps.residue_granularity == DMA_RESIDUE_GRANULARITY_DESCRIPTOR) {
+		ret = -EINVAL;
+		goto release_rx;
+	}
+
 	dmaengine_slave_config(dma->rxchan, &dma->rxconf);
 
 	/* Get a channel for TX */
@@ -185,8 +189,17 @@
 						       dma->fn, dma->tx_param,
 						       p->port.dev, "tx");
 	if (!dma->txchan) {
-		dma_release_channel(dma->rxchan);
-		return -ENODEV;
+		ret = -ENODEV;
+		goto release_rx;
+	}
+
+	/* 8250 tx dma requires dmaengine driver to support terminate */
+	ret = dma_get_slave_caps(dma->txchan, &caps);
+	if (ret)
+		goto err;
+	if (!caps.cmd_terminate) {
+		ret = -EINVAL;
+		goto err;
 	}
 
 	dmaengine_slave_config(dma->txchan, &dma->txconf);
@@ -197,8 +210,10 @@
 
 	dma->rx_buf = dma_alloc_coherent(dma->rxchan->device->dev, dma->rx_size,
 					&dma->rx_addr, GFP_KERNEL);
-	if (!dma->rx_buf)
+	if (!dma->rx_buf) {
+		ret = -ENOMEM;
 		goto err;
+	}
 
 	/* TX buffer */
 	dma->tx_addr = dma_map_single(dma->txchan->device->dev,
@@ -208,6 +223,7 @@
 	if (dma_mapping_error(dma->txchan->device->dev, dma->tx_addr)) {
 		dma_free_coherent(dma->rxchan->device->dev, dma->rx_size,
 				  dma->rx_buf, dma->rx_addr);
+		ret = -ENOMEM;
 		goto err;
 	}
 
@@ -215,10 +231,10 @@
 
 	return 0;
 err:
-	dma_release_channel(dma->rxchan);
 	dma_release_channel(dma->txchan);
-
-	return -ENOMEM;
+release_rx:
+	dma_release_channel(dma->rxchan);
+	return ret;
 }
 EXPORT_SYMBOL_GPL(serial8250_request_dma);
 
diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c
index a3fb95d..e199696 100644
--- a/drivers/tty/serial/8250/8250_dw.c
+++ b/drivers/tty/serial/8250/8250_dw.c
@@ -104,15 +104,16 @@
 		dw8250_force_idle(p);
 
 #ifdef CONFIG_64BIT
-		__raw_writeq(value & 0xff, offset);
-#else
+		if (p->type == PORT_OCTEON)
+			__raw_writeq(value & 0xff, offset);
+		else
+#endif
 		if (p->iotype == UPIO_MEM32)
 			writel(value, offset);
 		else if (p->iotype == UPIO_MEM32BE)
 			iowrite32be(value, offset);
 		else
 			writeb(value, offset);
-#endif
 	}
 	/*
 	 * FIXME: this deadlocks if port->lock is already held
@@ -617,6 +618,7 @@
 	{ "8086228A", 0 },
 	{ "APMC0D08", 0},
 	{ "AMD0020", 0 },
+	{ "AMDI0020", 0 },
 	{ },
 };
 MODULE_DEVICE_TABLE(acpi, dw8250_acpi_match);
diff --git a/drivers/tty/serial/8250/8250_fintek.c b/drivers/tty/serial/8250/8250_fintek.c
index 8947439..870981d 100644
--- a/drivers/tty/serial/8250/8250_fintek.c
+++ b/drivers/tty/serial/8250/8250_fintek.c
@@ -1,9 +1,7 @@
 /*
  *  Probe for F81216A LPC to 4 UART
  *
- *  Based on drivers/tty/serial/8250_pnp.c, by Russell King, et al
- *
- *  Copyright (C) 2014 Ricardo Ribalda, Qtechnology A/S
+ *  Copyright (C) 2014-2016 Ricardo Ribalda, Qtechnology A/S
  *
  *
  * This program is free software; you can redistribute it and/or modify
@@ -38,19 +36,15 @@
 #define RXW4C_IRA BIT(3)
 #define TXW4C_IRA BIT(2)
 
-#define DRIVER_NAME "8250_fintek"
-
 struct fintek_8250 {
 	u16 base_port;
 	u8 index;
 	u8 key;
-	long line;
 };
 
 static int fintek_8250_enter_key(u16 base_port, u8 key)
 {
-
-	if (!request_muxed_region(base_port, 2, DRIVER_NAME))
+	if (!request_muxed_region(base_port, 2, "8250_fintek"))
 		return -EBUSY;
 
 	outb(key, base_port + ADDR_PORT);
@@ -138,7 +132,7 @@
 	return 0;
 }
 
-static int fintek_8250_base_port(u16 io_address, u8 *key, u8 *index)
+static int find_base_port(struct fintek_8250 *pdata, u16 io_address)
 {
 	static const u16 addr[] = {0x4e, 0x2e};
 	static const u8 keys[] = {0x77, 0xa0, 0x87, 0x67};
@@ -168,10 +162,13 @@
 					continue;
 
 				fintek_8250_exit_key(addr[i]);
-				*key = keys[j];
-				*index = k;
-				return addr[i];
+				pdata->key = keys[j];
+				pdata->base_port = addr[i];
+				pdata->index = k;
+
+				return 0;
 			}
+
 			fintek_8250_exit_key(addr[i]);
 		}
 	}
@@ -179,104 +176,21 @@
 	return -ENODEV;
 }
 
-static int
-fintek_8250_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id)
+int fintek_8250_probe(struct uart_8250_port *uart)
 {
-	struct uart_8250_port uart;
 	struct fintek_8250 *pdata;
-	int base_port;
-	u8 key;
-	u8 index;
+	struct fintek_8250 probe_data;
 
-	if (!pnp_port_valid(dev, 0))
+	if (find_base_port(&probe_data, uart->port.iobase))
 		return -ENODEV;
 
-	base_port = fintek_8250_base_port(pnp_port_start(dev, 0), &key, &index);
-	if (base_port < 0)
-		return -ENODEV;
-
-	memset(&uart, 0, sizeof(uart));
-
-	pdata = devm_kzalloc(&dev->dev, sizeof(*pdata), GFP_KERNEL);
+	pdata = devm_kzalloc(uart->port.dev, sizeof(*pdata), GFP_KERNEL);
 	if (!pdata)
 		return -ENOMEM;
-	uart.port.private_data = pdata;
 
-	if (!pnp_irq_valid(dev, 0))
-		return -ENODEV;
-	uart.port.irq = pnp_irq(dev, 0);
-	uart.port.iobase = pnp_port_start(dev, 0);
-	uart.port.iotype = UPIO_PORT;
-	uart.port.rs485_config = fintek_8250_rs485_config;
+	memcpy(pdata, &probe_data, sizeof(probe_data));
+	uart->port.rs485_config = fintek_8250_rs485_config;
+	uart->port.private_data = pdata;
 
-	uart.port.flags |= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF;
-	if (pnp_irq_flags(dev, 0) & IORESOURCE_IRQ_SHAREABLE)
-		uart.port.flags |= UPF_SHARE_IRQ;
-	uart.port.uartclk = 1843200;
-	uart.port.dev = &dev->dev;
-
-	pdata->key = key;
-	pdata->base_port = base_port;
-	pdata->index = index;
-	pdata->line = serial8250_register_8250_port(&uart);
-	if (pdata->line < 0)
-		return -ENODEV;
-
-	pnp_set_drvdata(dev, pdata);
 	return 0;
 }
-
-static void fintek_8250_remove(struct pnp_dev *dev)
-{
-	struct fintek_8250 *pdata = pnp_get_drvdata(dev);
-
-	if (pdata)
-		serial8250_unregister_port(pdata->line);
-}
-
-#ifdef CONFIG_PM
-static int fintek_8250_suspend(struct pnp_dev *dev, pm_message_t state)
-{
-	struct fintek_8250 *pdata = pnp_get_drvdata(dev);
-
-	if (!pdata)
-		return -ENODEV;
-	serial8250_suspend_port(pdata->line);
-	return 0;
-}
-
-static int fintek_8250_resume(struct pnp_dev *dev)
-{
-	struct fintek_8250 *pdata = pnp_get_drvdata(dev);
-
-	if (!pdata)
-		return -ENODEV;
-	serial8250_resume_port(pdata->line);
-	return 0;
-}
-#else
-#define fintek_8250_suspend NULL
-#define fintek_8250_resume NULL
-#endif /* CONFIG_PM */
-
-static const struct pnp_device_id fintek_dev_table[] = {
-	/* Qtechnology Panel PC / IO1000 */
-	{ "PNP0501"},
-	{}
-};
-
-MODULE_DEVICE_TABLE(pnp, fintek_dev_table);
-
-static struct pnp_driver fintek_8250_driver = {
-	.name		= DRIVER_NAME,
-	.probe		= fintek_8250_probe,
-	.remove		= fintek_8250_remove,
-	.suspend	= fintek_8250_suspend,
-	.resume		= fintek_8250_resume,
-	.id_table	= fintek_dev_table,
-};
-
-module_pnp_driver(fintek_8250_driver);
-MODULE_DESCRIPTION("Fintek F812164 module");
-MODULE_AUTHOR("Ricardo Ribalda <ricardo.ribalda@gmail.com>");
-MODULE_LICENSE("GPL");
diff --git a/drivers/tty/serial/8250/8250_mid.c b/drivers/tty/serial/8250/8250_mid.c
index 88531a3..86379a7 100644
--- a/drivers/tty/serial/8250/8250_mid.c
+++ b/drivers/tty/serial/8250/8250_mid.c
@@ -9,11 +9,13 @@
  * published by the Free Software Foundation.
  */
 
-#include <linux/rational.h>
+#include <linux/bitops.h>
 #include <linux/module.h>
 #include <linux/pci.h>
+#include <linux/rational.h>
 
 #include <linux/dma/hsu.h>
+#include <linux/8250_pci.h>
 
 #include "8250.h"
 
@@ -24,6 +26,7 @@
 #define PCI_DEVICE_ID_INTEL_DNV_UART	0x19d8
 
 /* Intel MID Specific registers */
+#define INTEL_MID_UART_DNV_FISR		0x08
 #define INTEL_MID_UART_PS		0x30
 #define INTEL_MID_UART_MUL		0x34
 #define INTEL_MID_UART_DIV		0x38
@@ -31,6 +34,7 @@
 struct mid8250;
 
 struct mid8250_board {
+	unsigned int flags;
 	unsigned long freq;
 	unsigned int base_baud;
 	int (*setup)(struct mid8250 *, struct uart_port *p);
@@ -76,7 +80,11 @@
 	struct pci_dev *pdev = to_pci_dev(p->dev);
 	int index = PCI_FUNC(pdev->devfn);
 
-	/* Currently no support for HSU port0 */
+	/*
+	 * Device 0000:00:04.0 is not a real HSU port. It provides a global
+	 * register set for all HSU ports, although it has the same PCI ID.
+	 * Skip it here.
+	 */
 	if (index-- == 0)
 		return -ENODEV;
 
@@ -88,16 +96,16 @@
 static int dnv_handle_irq(struct uart_port *p)
 {
 	struct mid8250 *mid = p->private_data;
-	int ret;
+	unsigned int fisr = serial_port_in(p, INTEL_MID_UART_DNV_FISR);
+	int ret = IRQ_NONE;
 
-	ret = hsu_dma_irq(&mid->dma_chip, 0);
-	ret |= hsu_dma_irq(&mid->dma_chip, 1);
-
-	/* For now, letting the HW generate separate interrupt for the UART */
-	if (ret)
-		return ret;
-
-	return serial8250_handle_irq(p, serial_port_in(p, UART_IIR));
+	if (fisr & BIT(2))
+		ret |= hsu_dma_irq(&mid->dma_chip, 1);
+	if (fisr & BIT(1))
+		ret |= hsu_dma_irq(&mid->dma_chip, 0);
+	if (fisr & BIT(0))
+		ret |= serial8250_handle_irq(p, serial_port_in(p, UART_IIR));
+	return ret;
 }
 
 #define DNV_DMA_CHAN_OFFSET 0x80
@@ -106,12 +114,13 @@
 {
 	struct hsu_dma_chip *chip = &mid->dma_chip;
 	struct pci_dev *pdev = to_pci_dev(p->dev);
+	unsigned int bar = FL_GET_BASE(mid->board->flags);
 	int ret;
 
 	chip->dev = &pdev->dev;
 	chip->irq = pdev->irq;
 	chip->regs = p->membase;
-	chip->length = pci_resource_len(pdev, 0);
+	chip->length = pci_resource_len(pdev, bar);
 	chip->offset = DNV_DMA_CHAN_OFFSET;
 
 	/* Falling back to PIO mode if DMA probing fails */
@@ -217,6 +226,7 @@
 {
 	struct uart_8250_port uart;
 	struct mid8250 *mid;
+	unsigned int bar;
 	int ret;
 
 	ret = pcim_enable_device(pdev);
@@ -230,6 +240,7 @@
 		return -ENOMEM;
 
 	mid->board = (struct mid8250_board *)id->driver_data;
+	bar = FL_GET_BASE(mid->board->flags);
 
 	memset(&uart, 0, sizeof(struct uart_8250_port));
 
@@ -242,8 +253,8 @@
 	uart.port.flags = UPF_SHARE_IRQ | UPF_FIXED_PORT | UPF_FIXED_TYPE;
 	uart.port.set_termios = mid8250_set_termios;
 
-	uart.port.mapbase = pci_resource_start(pdev, 0);
-	uart.port.membase = pcim_iomap(pdev, 0, 0);
+	uart.port.mapbase = pci_resource_start(pdev, bar);
+	uart.port.membase = pcim_iomap(pdev, bar, 0);
 	if (!uart.port.membase)
 		return -ENOMEM;
 
@@ -282,18 +293,21 @@
 }
 
 static const struct mid8250_board pnw_board = {
+	.flags = FL_BASE0,
 	.freq = 50000000,
 	.base_baud = 115200,
 	.setup = pnw_setup,
 };
 
 static const struct mid8250_board tng_board = {
+	.flags = FL_BASE0,
 	.freq = 38400000,
 	.base_baud = 1843200,
 	.setup = tng_setup,
 };
 
 static const struct mid8250_board dnv_board = {
+	.flags = FL_BASE1,
 	.freq = 133333333,
 	.base_baud = 115200,
 	.setup = dnv_setup,
diff --git a/drivers/tty/serial/8250/8250_of.c b/drivers/tty/serial/8250/8250_of.c
index c7ed3d2..38963d7 100644
--- a/drivers/tty/serial/8250/8250_of.c
+++ b/drivers/tty/serial/8250/8250_of.c
@@ -29,7 +29,7 @@
 };
 
 #ifdef CONFIG_ARCH_TEGRA
-void tegra_serial_handle_break(struct uart_port *p)
+static void tegra_serial_handle_break(struct uart_port *p)
 {
 	unsigned int status, tmout = 10000;
 
diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c
index 6f76051..2c44c79 100644
--- a/drivers/tty/serial/8250/8250_omap.c
+++ b/drivers/tty/serial/8250/8250_omap.c
@@ -115,6 +115,12 @@
 	bool rx_dma_broken;
 };
 
+#ifdef CONFIG_SERIAL_8250_DMA
+static void omap_8250_rx_dma_flush(struct uart_8250_port *p);
+#else
+static inline void omap_8250_rx_dma_flush(struct uart_8250_port *p) { }
+#endif
+
 static u32 uart_read(struct uart_8250_port *up, u32 reg)
 {
 	return readl(up->port.membase + (reg << up->port.regshift));
@@ -635,7 +641,7 @@
 	serial_out(up, UART_OMAP_WER, priv->wer);
 
 	if (up->dma)
-		up->dma->rx_dma(up, 0);
+		up->dma->rx_dma(up);
 
 	pm_runtime_mark_last_busy(port->dev);
 	pm_runtime_put_autosuspend(port->dev);
@@ -654,7 +660,7 @@
 
 	flush_work(&priv->qos_work);
 	if (up->dma)
-		up->dma->rx_dma(up, UART_IIR_RX_TIMEOUT);
+		omap_8250_rx_dma_flush(up);
 
 	pm_runtime_get_sync(port->dev);
 
@@ -742,9 +748,9 @@
 }
 
 #ifdef CONFIG_SERIAL_8250_DMA
-static int omap_8250_rx_dma(struct uart_8250_port *p, unsigned int iir);
+static int omap_8250_rx_dma(struct uart_8250_port *p);
 
-static void __dma_rx_do_complete(struct uart_8250_port *p, bool error)
+static void __dma_rx_do_complete(struct uart_8250_port *p)
 {
 	struct omap8250_priv	*priv = p->port.private_data;
 	struct uart_8250_dma    *dma = p->dma;
@@ -754,9 +760,6 @@
 	unsigned long		flags;
 	int			ret;
 
-	dma_sync_single_for_cpu(dma->rxchan->device->dev, dma->rx_addr,
-				dma->rx_size, DMA_FROM_DEVICE);
-
 	spin_lock_irqsave(&priv->rx_dma_lock, flags);
 
 	if (!dma->rx_running)
@@ -764,7 +767,6 @@
 
 	dma->rx_running = 0;
 	dmaengine_tx_status(dma->rxchan, dma->rx_cookie, &state);
-	dmaengine_terminate_all(dma->rxchan);
 
 	count = dma->rx_size - state.residue;
 
@@ -775,15 +777,13 @@
 unlock:
 	spin_unlock_irqrestore(&priv->rx_dma_lock, flags);
 
-	if (!error)
-		omap_8250_rx_dma(p, 0);
-
 	tty_flip_buffer_push(tty_port);
 }
 
 static void __dma_rx_complete(void *param)
 {
-	__dma_rx_do_complete(param, false);
+	__dma_rx_do_complete(param);
+	omap_8250_rx_dma(param);
 }
 
 static void omap_8250_rx_dma_flush(struct uart_8250_port *p)
@@ -806,10 +806,11 @@
 
 	spin_unlock_irqrestore(&priv->rx_dma_lock, flags);
 
-	__dma_rx_do_complete(p, true);
+	__dma_rx_do_complete(p);
+	dmaengine_terminate_all(dma->rxchan);
 }
 
-static int omap_8250_rx_dma(struct uart_8250_port *p, unsigned int iir)
+static int omap_8250_rx_dma(struct uart_8250_port *p)
 {
 	struct omap8250_priv		*priv = p->port.private_data;
 	struct uart_8250_dma            *dma = p->dma;
@@ -817,35 +818,6 @@
 	struct dma_async_tx_descriptor  *desc;
 	unsigned long			flags;
 
-	switch (iir & 0x3f) {
-	case UART_IIR_RLSI:
-		/* 8250_core handles errors and break interrupts */
-		omap_8250_rx_dma_flush(p);
-		return -EIO;
-	case UART_IIR_RX_TIMEOUT:
-		/*
-		 * If RCVR FIFO trigger level was not reached, complete the
-		 * transfer and let 8250_core copy the remaining data.
-		 */
-		omap_8250_rx_dma_flush(p);
-		return -ETIMEDOUT;
-	case UART_IIR_RDI:
-		/*
-		 * The OMAP UART is a special BEAST. If we receive RDI we _have_
-		 * a DMA transfer programmed but it didn't work. One reason is
-		 * that we were too slow and there were too many bytes in the
-		 * FIFO, the UART counted wrong and never kicked the DMA engine
-		 * to do anything. That means once we receive RDI on OMAP then
-		 * the DMA won't do anything soon so we have to cancel the DMA
-		 * transfer and purge the FIFO manually.
-		 */
-		omap_8250_rx_dma_flush(p);
-		return -ETIMEDOUT;
-
-	default:
-		break;
-	}
-
 	if (priv->rx_dma_broken)
 		return -EINVAL;
 
@@ -868,9 +840,6 @@
 
 	dma->rx_cookie = dmaengine_submit(desc);
 
-	dma_sync_single_for_device(dma->rxchan->device->dev, dma->rx_addr,
-				   dma->rx_size, DMA_FROM_DEVICE);
-
 	dma_async_issue_pending(dma->rxchan);
 out:
 	spin_unlock_irqrestore(&priv->rx_dma_lock, flags);
@@ -1022,6 +991,18 @@
 	return ret;
 }
 
+static bool handle_rx_dma(struct uart_8250_port *up, unsigned int iir)
+{
+	switch (iir & 0x3f) {
+	case UART_IIR_RLSI:
+	case UART_IIR_RX_TIMEOUT:
+	case UART_IIR_RDI:
+		omap_8250_rx_dma_flush(up);
+		return true;
+	}
+	return omap_8250_rx_dma(up);
+}
+
 /*
  * This is mostly serial8250_handle_irq(). We have a slightly different DMA
  * hoook for RX/TX and need different logic for them in the ISR. Therefore we
@@ -1033,7 +1014,6 @@
 	unsigned char status;
 	unsigned long flags;
 	u8 iir;
-	int dma_err = 0;
 
 	serial8250_rpm_get(up);
 
@@ -1048,11 +1028,9 @@
 	status = serial_port_in(port, UART_LSR);
 
 	if (status & (UART_LSR_DR | UART_LSR_BI)) {
-
-		dma_err = omap_8250_rx_dma(up, iir);
-		if (dma_err) {
+		if (handle_rx_dma(up, iir)) {
 			status = serial8250_rx_chars(up, status);
-			omap_8250_rx_dma(up, 0);
+			omap_8250_rx_dma(up);
 		}
 	}
 	serial8250_modem_status(up);
@@ -1066,8 +1044,7 @@
 			 * try again due to an earlier failer which
 			 * might have been resolved by now.
 			 */
-			dma_err = omap_8250_tx_dma(up);
-			if (dma_err)
+			if (omap_8250_tx_dma(up))
 				serial8250_tx_chars(up);
 		}
 	}
@@ -1084,7 +1061,7 @@
 
 #else
 
-static inline int omap_8250_rx_dma(struct uart_8250_port *p, unsigned int iir)
+static inline int omap_8250_rx_dma(struct uart_8250_port *p)
 {
 	return -EINVAL;
 }
@@ -1395,7 +1372,7 @@
 	}
 
 	if (up->dma && up->dma->rxchan)
-		omap_8250_rx_dma(up, UART_IIR_RX_TIMEOUT);
+		omap_8250_rx_dma_flush(up);
 
 	priv->latency = PM_QOS_CPU_DMA_LAT_DEFAULT_VALUE;
 	schedule_work(&priv->qos_work);
@@ -1407,20 +1384,18 @@
 {
 	struct omap8250_priv *priv = dev_get_drvdata(dev);
 	struct uart_8250_port *up;
-	int loss_cntx;
 
 	/* In case runtime-pm tries this before we are setup */
 	if (!priv)
 		return 0;
 
 	up = serial8250_get_port(priv->line);
-	loss_cntx = omap8250_lost_context(up);
 
-	if (loss_cntx)
+	if (omap8250_lost_context(up))
 		omap8250_restore_regs(up);
 
 	if (up->dma && up->dma->rxchan)
-		omap_8250_rx_dma(up, 0);
+		omap_8250_rx_dma(up);
 
 	priv->latency = priv->calc_latency;
 	schedule_work(&priv->qos_work);
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index 5eea74d..8dd250f 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -1377,6 +1377,9 @@
 	unsigned long m, n;
 	u32 reg;
 
+	/* Gracefully handle the B0 case: fall back to B9600 */
+	fuart = fuart ? fuart : 9600 * 16;
+
 	/* Get Fuart closer to Fref */
 	fuart *= rounddown_pow_of_two(fref / fuart);
 
@@ -1413,6 +1416,17 @@
 	return true;
 }
 
+static unsigned int
+byt_get_mctrl(struct uart_port *port)
+{
+	unsigned int ret = serial8250_do_get_mctrl(port);
+
+	/* Force DCD and DSR signals to permanently be reported as active. */
+	ret |= TIOCM_CAR | TIOCM_DSR;
+
+	return ret;
+}
+
 static int
 byt_serial_setup(struct serial_private *priv,
 		 const struct pciserial_board *board,
@@ -1477,6 +1491,7 @@
 	port->port.type = PORT_16550A;
 	port->port.flags = (port->port.flags | UPF_FIXED_PORT | UPF_FIXED_TYPE);
 	port->port.set_termios = byt_set_termios;
+	port->port.get_mctrl = byt_get_mctrl;
 	port->port.fifosize = 64;
 	port->tx_loadsz = 64;
 	port->dma = dma;
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index 00ad263..d403603 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -1315,6 +1315,13 @@
 
 out_lock:
 	spin_unlock_irqrestore(&port->lock, flags);
+
+	/*
+	 * Check if the device is a Fintek F81216A
+	 */
+	if (port->type == PORT_16550A)
+		fintek_8250_probe(up);
+
 	if (up->capabilities != old_capabilities) {
 		pr_warn("ttyS%d: detected caps %08x should be %08x\n",
 		       serial_index(port), old_capabilities,
@@ -1788,6 +1795,18 @@
 }
 EXPORT_SYMBOL_GPL(serial8250_modem_status);
 
+static bool handle_rx_dma(struct uart_8250_port *up, unsigned int iir)
+{
+	switch (iir & 0x3f) {
+	case UART_IIR_RX_TIMEOUT:
+		serial8250_rx_dma_flush(up);
+		/* fall-through */
+	case UART_IIR_RLSI:
+		return true;
+	}
+	return up->dma->rx_dma(up);
+}
+
 /*
  * This handles the interrupt from one port.
  */
@@ -1796,7 +1815,6 @@
 	unsigned char status;
 	unsigned long flags;
 	struct uart_8250_port *up = up_to_u8250p(port);
-	int dma_err = 0;
 
 	if (iir & UART_IIR_NO_INT)
 		return 0;
@@ -1808,15 +1826,11 @@
 	DEBUG_INTR("status = %x...", status);
 
 	if (status & (UART_LSR_DR | UART_LSR_BI)) {
-		if (up->dma)
-			dma_err = up->dma->rx_dma(up, iir);
-
-		if (!up->dma || dma_err)
+		if (!up->dma || handle_rx_dma(up, iir))
 			status = serial8250_rx_chars(up, status);
 	}
 	serial8250_modem_status(up);
-	if ((!up->dma || (up->dma && up->dma->tx_err)) &&
-	    (status & UART_LSR_THRE))
+	if ((!up->dma || up->dma->tx_err) && (status & UART_LSR_THRE))
 		serial8250_tx_chars(up);
 
 	spin_unlock_irqrestore(&port->lock, flags);
@@ -1882,7 +1896,7 @@
 	return (lsr & BOTH_EMPTY) == BOTH_EMPTY ? TIOCSER_TEMT : 0;
 }
 
-static unsigned int serial8250_get_mctrl(struct uart_port *port)
+unsigned int serial8250_do_get_mctrl(struct uart_port *port)
 {
 	struct uart_8250_port *up = up_to_u8250p(port);
 	unsigned int status;
@@ -1903,6 +1917,14 @@
 		ret |= TIOCM_CTS;
 	return ret;
 }
+EXPORT_SYMBOL_GPL(serial8250_do_get_mctrl);
+
+static unsigned int serial8250_get_mctrl(struct uart_port *port)
+{
+	if (port->get_mctrl)
+		return port->get_mctrl(port);
+	return serial8250_do_get_mctrl(port);
+}
 
 void serial8250_do_set_mctrl(struct uart_port *port, unsigned int mctrl)
 {
diff --git a/drivers/tty/serial/8250/8250_uniphier.c b/drivers/tty/serial/8250/8250_uniphier.c
index 1b7bd26..efd1f9c 100644
--- a/drivers/tty/serial/8250/8250_uniphier.c
+++ b/drivers/tty/serial/8250/8250_uniphier.c
@@ -209,7 +209,7 @@
 
 	irq = platform_get_irq(pdev, 0);
 	if (irq < 0) {
-		dev_err(dev, "failed to get IRQ number");
+		dev_err(dev, "failed to get IRQ number\n");
 		return irq;
 	}
 
diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig
index 4d7cb9c..e46761d 100644
--- a/drivers/tty/serial/8250/Kconfig
+++ b/drivers/tty/serial/8250/Kconfig
@@ -57,6 +57,18 @@
 	  This builds standard PNP serial support. You may be able to
 	  disable this feature if you only need legacy serial support.
 
+config SERIAL_8250_FINTEK
+	bool "Support for Fintek F81216A LPC to 4 UART RS485 API"
+	depends on SERIAL_8250
+	---help---
+	  Selecting this option will add support for the RS485 capabilities
+	  of the Fintek F81216A LPC to 4 UART.
+
+	  If this option is not selected the device will be configured as a
+	  standard 16550A serial port.
+
+	  If unsure, say N.
+
 config SERIAL_8250_CONSOLE
 	bool "Console on 8250/16550 and compatible serial port"
 	depends on SERIAL_8250=y
@@ -358,14 +370,6 @@
 	  not booting kernel because the serial console remains silent in case
 	  they forgot to update the command line.
 
-config SERIAL_8250_FINTEK
-	tristate "Support for Fintek F81216A LPC to 4 UART"
-	depends on SERIAL_8250 && PNP
-	help
-	  Selecting this option will add support for the Fintek F81216A
-	  LPC to 4 UART. This device has some RS485 functionality not available
-	  through the PNP driver. If unsure, say N.
-
 config SERIAL_8250_LPC18XX
 	tristate "NXP LPC18xx/43xx serial port support"
 	depends on SERIAL_8250 && OF && (ARCH_LPC18XX || COMPILE_TEST)
@@ -398,8 +402,10 @@
 	  its UARTs, say Y to this option. If unsure, say N.
 
 config SERIAL_8250_MID
-	tristate "Support for serial ports on Intel MID platforms"
+	tristate "Support for serial ports on Intel MID platforms" if EXPERT
+	default SERIAL_8250
 	depends on SERIAL_8250 && PCI
+	depends on X86 || COMPILE_TEST
 	select HSU_DMA if SERIAL_8250_DMA
 	select HSU_DMA_PCI if (HSU_DMA && X86_INTEL_MID)
 	select RATIONAL
diff --git a/drivers/tty/serial/8250/Makefile b/drivers/tty/serial/8250/Makefile
index c9a2d6e..367d403 100644
--- a/drivers/tty/serial/8250/Makefile
+++ b/drivers/tty/serial/8250/Makefile
@@ -7,6 +7,7 @@
 8250-$(CONFIG_SERIAL_8250_PNP)		+= 8250_pnp.o
 8250_base-y				:= 8250_port.o
 8250_base-$(CONFIG_SERIAL_8250_DMA)	+= 8250_dma.o
+8250_base-$(CONFIG_SERIAL_8250_FINTEK)	+= 8250_fintek.o
 obj-$(CONFIG_SERIAL_8250_GSC)		+= 8250_gsc.o
 obj-$(CONFIG_SERIAL_8250_PCI)		+= 8250_pci.o
 obj-$(CONFIG_SERIAL_8250_HP300)		+= 8250_hp300.o
@@ -23,7 +24,6 @@
 obj-$(CONFIG_SERIAL_8250_DW)		+= 8250_dw.o
 obj-$(CONFIG_SERIAL_8250_EM)		+= 8250_em.o
 obj-$(CONFIG_SERIAL_8250_OMAP)		+= 8250_omap.o
-obj-$(CONFIG_SERIAL_8250_FINTEK)	+= 8250_fintek.o
 obj-$(CONFIG_SERIAL_8250_LPC18XX)	+= 8250_lpc18xx.o
 obj-$(CONFIG_SERIAL_8250_MT6577)	+= 8250_mtk.o
 obj-$(CONFIG_SERIAL_8250_UNIPHIER)	+= 8250_uniphier.o
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 7711b26..7e3a58c 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -213,6 +213,7 @@
 	bool "Support for console on meson"
 	depends on SERIAL_MESON=y
 	select SERIAL_CORE_CONSOLE
+	select SERIAL_EARLYCON
 	help
 	  Say Y here if you wish to use a Amlogic MesonX UART as the
 	  system console (the system console is the device which
@@ -1404,11 +1405,12 @@
 config SERIAL_MXS_AUART
 	tristate "MXS AUART support"
 	depends on HAS_DMA
-	depends on ARCH_MXS || COMPILE_TEST
+	depends on ARCH_MXS || MACH_ASM9260 || COMPILE_TEST
 	select SERIAL_CORE
 	select SERIAL_MCTRL_GPIO if GPIOLIB
 	help
-	  This driver supports the MXS Application UART (AUART) port.
+	  This driver supports the MXS and Alphascale ASM9260 Application
+	  UART (AUART) port.
 
 config SERIAL_MXS_AUART_CONSOLE
 	bool "MXS AUART console support"
@@ -1467,6 +1469,19 @@
 	  This driver support the USART and UART ports on
 	  Energy Micro's efm32 SoCs.
 
+config SERIAL_MPS2_UART_CONSOLE
+	bool "MPS2 UART console support"
+	depends on SERIAL_MPS2_UART
+	select SERIAL_CORE_CONSOLE
+	select SERIAL_EARLYCON
+
+config SERIAL_MPS2_UART
+	bool "MPS2 UART port"
+	depends on ARM || COMPILE_TEST
+	select SERIAL_CORE
+	help
+	  This driver support the UART ports on ARM MPS2.
+
 config SERIAL_EFM32_UART_CONSOLE
 	bool "EFM32 UART/USART console support"
 	depends on SERIAL_EFM32_UART=y
@@ -1625,6 +1640,7 @@
 
 config SERIAL_MVEBU_UART
 	bool "Marvell EBU serial port support"
+	depends on ARCH_MVEBU || COMPILE_TEST
 	select SERIAL_CORE
 	help
 	  This driver is for Marvell EBU SoC's UART. If you have a machine
diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
index 74914aa..1278d37 100644
--- a/drivers/tty/serial/Makefile
+++ b/drivers/tty/serial/Makefile
@@ -92,6 +92,7 @@
 obj-$(CONFIG_SERIAL_STM32)	+= stm32-usart.o
 obj-$(CONFIG_SERIAL_MVEBU_UART)	+= mvebu-uart.o
 obj-$(CONFIG_SERIAL_PIC32)	+= pic32_uart.o
+obj-$(CONFIG_SERIAL_MPS2_UART)	+= mps2-uart.o
 
 # GPIOLIB helpers for modem control lines
 obj-$(CONFIG_SERIAL_MCTRL_GPIO)	+= serial_mctrl_gpio.o
diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c
index 7c198e0..a2aa655 100644
--- a/drivers/tty/serial/amba-pl011.c
+++ b/drivers/tty/serial/amba-pl011.c
@@ -121,6 +121,7 @@
 
 static struct vendor_data vendor_sbsa = {
 	.reg_offset		= pl011_std_offsets,
+	.access_32b		= true,
 	.oversampling		= false,
 	.dma_threshold		= false,
 	.cts_event_workaround	= false,
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index d9439e6..954941d 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -274,6 +274,13 @@
 	return atmel_port->use_dma_rx;
 }
 
+static bool atmel_use_fifo(struct uart_port *port)
+{
+	struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
+
+	return atmel_port->fifo_size;
+}
+
 static unsigned int atmel_get_lines_status(struct uart_port *port)
 {
 	struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
@@ -2090,7 +2097,12 @@
 		mode |= ATMEL_US_USMODE_RS485;
 	} else if (termios->c_cflag & CRTSCTS) {
 		/* RS232 with hardware handshake (RTS/CTS) */
-		mode |= ATMEL_US_USMODE_HWHS;
+		if (atmel_use_dma_rx(port) && !atmel_use_fifo(port)) {
+			dev_info(port->dev, "not enabling hardware flow control because DMA is used");
+			termios->c_cflag &= ~CRTSCTS;
+		} else {
+			mode |= ATMEL_US_USMODE_HWHS;
+		}
 	} else {
 		/* RS232 without hadware handshake */
 		mode |= ATMEL_US_USMODE_NORMAL;
diff --git a/drivers/tty/serial/crisv10.c b/drivers/tty/serial/crisv10.c
index c0172bf54..315c849 100644
--- a/drivers/tty/serial/crisv10.c
+++ b/drivers/tty/serial/crisv10.c
@@ -2599,7 +2599,7 @@
 
 	/* if it was already initialized, skip this */
 
-	if (info->port.flags & ASYNC_INITIALIZED) {
+	if (tty_port_initialized(&info->port)) {
 		local_irq_restore(flags);
 		free_page(xmit_page);
 		return 0;
@@ -2703,7 +2703,7 @@
 	e100_rts(info, 1);
 	e100_dtr(info, 1);
 
-	info->port.flags |= ASYNC_INITIALIZED;
+	tty_port_set_initialized(&info->port, 1);
 
 	local_irq_restore(flags);
 	return 0;
@@ -2745,7 +2745,7 @@
 		info->tr_running = 0;
 	}
 
-	if (!(info->port.flags & ASYNC_INITIALIZED))
+	if (!tty_port_initialized(&info->port))
 		return;
 
 #ifdef SERIAL_DEBUG_OPEN
@@ -2776,7 +2776,7 @@
 	if (info->port.tty)
 		set_bit(TTY_IO_ERROR, &info->port.tty->flags);
 
-	info->port.flags &= ~ASYNC_INITIALIZED;
+	tty_port_set_initialized(&info->port, 0);
 	local_irq_restore(flags);
 }
 
@@ -3273,9 +3273,9 @@
 	info->port.low_latency = (info->port.flags & ASYNC_LOW_LATENCY) ? 1 : 0;
 
  check_and_exit:
-	if (info->port.flags & ASYNC_INITIALIZED) {
+	if (tty_port_initialized(&info->port))
 		change_speed(info);
-	} else
+	else
 		retval = startup(info);
 	return retval;
 }
@@ -3445,7 +3445,7 @@
 	if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
 	    (cmd != TIOCSERCONFIG) && (cmd != TIOCSERGWILD)  &&
 	    (cmd != TIOCSERSWILD) && (cmd != TIOCSERGSTRUCT)) {
-		if (tty->flags & (1 << TTY_IO_ERROR))
+		if (tty_io_error(tty))
 			return -EIO;
 	}
 
@@ -3628,7 +3628,7 @@
 	e100_disable_rx(info);
 	e100_disable_rx_irq(info);
 
-	if (info->port.flags & ASYNC_INITIALIZED) {
+	if (tty_port_initialized(&info->port)) {
 		/*
 		 * Before we drop DTR, make sure the UART transmitter
 		 * has completely drained; this is especially
@@ -3648,8 +3648,8 @@
 			schedule_timeout_interruptible(info->port.close_delay);
 		wake_up_interruptible(&info->port.open_wait);
 	}
-	info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
 	local_irq_restore(flags);
+	tty_port_set_active(&info->port, 0);
 
 	/* port closed */
 
@@ -3732,7 +3732,7 @@
 	shutdown(info);
 	info->event = 0;
 	info->port.count = 0;
-	info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
+	tty_port_set_active(&info->port, 0);
 	info->port.tty = NULL;
 	wake_up_interruptible(&info->port.open_wait);
 }
@@ -3755,9 +3755,8 @@
 	 * If non-blocking mode is set, or the port is not enabled,
 	 * then make the check up front and then exit.
 	 */
-	if ((filp->f_flags & O_NONBLOCK) ||
-	    (tty->flags & (1 << TTY_IO_ERROR))) {
-		info->port.flags |= ASYNC_NORMAL_ACTIVE;
+	if ((filp->f_flags & O_NONBLOCK) || tty_io_error(tty)) {
+		tty_port_set_active(&info->port, 1);
 		return 0;
 	}
 
@@ -3788,8 +3787,7 @@
 		e100_dtr(info, 1);
 		local_irq_restore(flags);
 		set_current_state(TASK_INTERRUPTIBLE);
-		if (tty_hung_up_p(filp) ||
-		    !(info->port.flags & ASYNC_INITIALIZED)) {
+		if (tty_hung_up_p(filp) || !tty_port_initialized(&info->port)) {
 #ifdef SERIAL_DO_RESTART
 			if (info->port.flags & ASYNC_HUP_NOTIFY)
 				retval = -EAGAIN;
@@ -3826,7 +3824,7 @@
 #endif
 	if (retval)
 		return retval;
-	info->port.flags |= ASYNC_NORMAL_ACTIVE;
+	tty_port_set_active(&info->port, 1);
 	return 0;
 }
 
diff --git a/drivers/tty/serial/ifx6x60.c b/drivers/tty/serial/ifx6x60.c
index 2085a6c..d386346 100644
--- a/drivers/tty/serial/ifx6x60.c
+++ b/drivers/tty/serial/ifx6x60.c
@@ -651,7 +651,7 @@
 	struct ifx_spi_device *ifx_dev = ctx;
 	int length;
 	int actual_length;
-	unsigned char more;
+	unsigned char more = 0;
 	unsigned char cts;
 	int local_write_pending = 0;
 	int queue_length;
diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index 231e7d5..0df2b1c 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -114,6 +114,7 @@
 #define UCR3_RXDSEN	(1<<6)	/* Receive status interrupt enable */
 #define UCR3_AIRINTEN	(1<<5)	/* Async IR wake interrupt enable */
 #define UCR3_AWAKEN	(1<<4)	/* Async wake interrupt enable */
+#define UCR3_DTRDEN	(1<<3)	/* Data Terminal Ready Delta Enable. */
 #define IMX21_UCR3_RXDMUXSEL	(1<<2)	/* RXD Muxed Input Select */
 #define UCR3_INVT	(1<<1)	/* Inverted Infrared transmission */
 #define UCR3_BPEN	(1<<0)	/* Preset registers enable */
@@ -142,7 +143,7 @@
 #define USR1_FRAMERR	(1<<10) /* Frame error interrupt flag */
 #define USR1_RRDY	(1<<9)	 /* Receiver ready interrupt/dma flag */
 #define USR1_AGTIM	(1<<8)	 /* Ageing timer interrupt flag */
-#define USR1_TIMEOUT	(1<<7)	 /* Receive timeout interrupt status */
+#define USR1_DTRD	(1<<7)	 /* DTR Delta */
 #define USR1_RXDS	 (1<<6)	 /* Receiver idle interrupt flag */
 #define USR1_AIRINT	 (1<<5)	 /* Async IR wake interrupt flag */
 #define USR1_AWAKE	 (1<<4)	 /* Aysnc wake interrupt flag */
@@ -361,6 +362,7 @@
 			imx_port_rts_inactive(sport, &temp);
 		else
 			imx_port_rts_active(sport, &temp);
+		temp |= UCR2_RXEN;
 		writel(temp, port->membase + UCR2);
 
 		temp = readl(port->membase + UCR4);
@@ -568,6 +570,8 @@
 			imx_port_rts_inactive(sport, &temp);
 		else
 			imx_port_rts_active(sport, &temp);
+		if (!(port->rs485.flags & SER_RS485_RX_DURING_TX))
+			temp &= ~UCR2_RXEN;
 		writel(temp, port->membase + UCR2);
 
 		/* enable transmitter and shifter empty irq */
@@ -729,11 +733,61 @@
 	spin_unlock_irqrestore(&sport->port.lock, flags);
 }
 
+/*
+ * We have a modem side uart, so the meanings of RTS and CTS are inverted.
+ */
+static unsigned int imx_get_hwmctrl(struct imx_port *sport)
+{
+	unsigned int tmp = TIOCM_DSR;
+	unsigned usr1 = readl(sport->port.membase + USR1);
+
+	if (usr1 & USR1_RTSS)
+		tmp |= TIOCM_CTS;
+
+	/* in DCE mode DCDIN is always 0 */
+	if (!(usr1 & USR2_DCDIN))
+		tmp |= TIOCM_CAR;
+
+	if (sport->dte_mode)
+		if (!(readl(sport->port.membase + USR2) & USR2_RIIN))
+			tmp |= TIOCM_RI;
+
+	return tmp;
+}
+
+/*
+ * Handle any change of modem status signal since we were last called.
+ */
+static void imx_mctrl_check(struct imx_port *sport)
+{
+	unsigned int status, changed;
+
+	status = imx_get_hwmctrl(sport);
+	changed = status ^ sport->old_status;
+
+	if (changed == 0)
+		return;
+
+	sport->old_status = status;
+
+	if (changed & TIOCM_RI && status & TIOCM_RI)
+		sport->port.icount.rng++;
+	if (changed & TIOCM_DSR)
+		sport->port.icount.dsr++;
+	if (changed & TIOCM_CAR)
+		uart_handle_dcd_change(&sport->port, status & TIOCM_CAR);
+	if (changed & TIOCM_CTS)
+		uart_handle_cts_change(&sport->port, status & TIOCM_CTS);
+
+	wake_up_interruptible(&sport->port.state->port.delta_msr_wait);
+}
+
 static irqreturn_t imx_int(int irq, void *dev_id)
 {
 	struct imx_port *sport = dev_id;
 	unsigned int sts;
 	unsigned int sts2;
+	irqreturn_t ret = IRQ_NONE;
 
 	sts = readl(sport->port.membase + USR1);
 	sts2 = readl(sport->port.membase + USR2);
@@ -743,26 +797,47 @@
 			imx_dma_rxint(sport);
 		else
 			imx_rxint(irq, dev_id);
+		ret = IRQ_HANDLED;
 	}
 
 	if ((sts & USR1_TRDY &&
 	     readl(sport->port.membase + UCR1) & UCR1_TXMPTYEN) ||
 	    (sts2 & USR2_TXDC &&
-	     readl(sport->port.membase + UCR4) & UCR4_TCEN))
+	     readl(sport->port.membase + UCR4) & UCR4_TCEN)) {
 		imx_txint(irq, dev_id);
+		ret = IRQ_HANDLED;
+	}
 
-	if (sts & USR1_RTSD)
+	if (sts & USR1_DTRD) {
+		unsigned long flags;
+
+		if (sts & USR1_DTRD)
+			writel(USR1_DTRD, sport->port.membase + USR1);
+
+		spin_lock_irqsave(&sport->port.lock, flags);
+		imx_mctrl_check(sport);
+		spin_unlock_irqrestore(&sport->port.lock, flags);
+
+		ret = IRQ_HANDLED;
+	}
+
+	if (sts & USR1_RTSD) {
 		imx_rtsint(irq, dev_id);
+		ret = IRQ_HANDLED;
+	}
 
-	if (sts & USR1_AWAKE)
+	if (sts & USR1_AWAKE) {
 		writel(USR1_AWAKE, sport->port.membase + USR1);
+		ret = IRQ_HANDLED;
+	}
 
 	if (sts2 & USR2_ORE) {
 		sport->port.icount.overrun++;
 		writel(USR2_ORE, sport->port.membase + USR2);
+		ret = IRQ_HANDLED;
 	}
 
-	return IRQ_HANDLED;
+	return ret;
 }
 
 /*
@@ -782,28 +857,6 @@
 	return ret;
 }
 
-/*
- * We have a modem side uart, so the meanings of RTS and CTS are inverted.
- */
-static unsigned int imx_get_hwmctrl(struct imx_port *sport)
-{
-	unsigned int tmp = TIOCM_DSR;
-	unsigned usr1 = readl(sport->port.membase + USR1);
-
-	if (usr1 & USR1_RTSS)
-		tmp |= TIOCM_CTS;
-
-	/* in DCE mode DCDIN is always 0 */
-	if (!(usr1 & USR2_DCDIN))
-		tmp |= TIOCM_CAR;
-
-	/* in DCE mode RIIN is always 0 */
-	if (readl(sport->port.membase + USR2) & USR2_RIIN)
-		tmp |= TIOCM_RI;
-
-	return tmp;
-}
-
 static unsigned int imx_get_mctrl(struct uart_port *port)
 {
 	struct imx_port *sport = (struct imx_port *)port;
@@ -861,33 +914,6 @@
 }
 
 /*
- * Handle any change of modem status signal since we were last called.
- */
-static void imx_mctrl_check(struct imx_port *sport)
-{
-	unsigned int status, changed;
-
-	status = imx_get_hwmctrl(sport);
-	changed = status ^ sport->old_status;
-
-	if (changed == 0)
-		return;
-
-	sport->old_status = status;
-
-	if (changed & TIOCM_RI)
-		sport->port.icount.rng++;
-	if (changed & TIOCM_DSR)
-		sport->port.icount.dsr++;
-	if (changed & TIOCM_CAR)
-		uart_handle_dcd_change(&sport->port, status & TIOCM_CAR);
-	if (changed & TIOCM_CTS)
-		uart_handle_cts_change(&sport->port, status & TIOCM_CTS);
-
-	wake_up_interruptible(&sport->port.state->port.delta_msr_wait);
-}
-
-/*
  * This is our per-port timeout handler, for checking the
  * modem status signals.
  */
@@ -1193,7 +1219,7 @@
 	/*
 	 * Finally, clear and enable interrupts
 	 */
-	writel(USR1_RTSD, sport->port.membase + USR1);
+	writel(USR1_RTSD | USR1_DTRD, sport->port.membase + USR1);
 	writel(USR2_ORE, sport->port.membase + USR2);
 
 	if (sport->dma_is_inited && !sport->dma_is_enabled)
@@ -1212,11 +1238,32 @@
 	temp |= (UCR2_RXEN | UCR2_TXEN);
 	if (!sport->have_rtscts)
 		temp |= UCR2_IRTS;
+	/*
+	 * make sure the edge sensitive RTS-irq is disabled,
+	 * we're using RTSD instead.
+	 */
+	if (!is_imx1_uart(sport))
+		temp &= ~UCR2_RTSEN;
 	writel(temp, sport->port.membase + UCR2);
 
 	if (!is_imx1_uart(sport)) {
 		temp = readl(sport->port.membase + UCR3);
-		temp |= IMX21_UCR3_RXDMUXSEL | UCR3_ADNIMP;
+
+		/*
+		 * The effect of RI and DCD differs depending on the UFCR_DCEDTE
+		 * bit. In DCE mode they control the outputs, in DTE mode they
+		 * enable the respective irqs. At least the DCD irq cannot be
+		 * cleared on i.MX25 at least, so it's not usable and must be
+		 * disabled. I don't have test hardware to check if RI has the
+		 * same problem but I consider this likely so it's disabled for
+		 * now, too.
+		 */
+		temp |= IMX21_UCR3_RXDMUXSEL | UCR3_ADNIMP |
+			UCR3_DTRDEN | UCR3_RI | UCR3_DCD;
+
+		if (sport->dte_mode)
+			temp &= ~(UCR3_RI | UCR3_DCD);
+
 		writel(temp, sport->port.membase + UCR3);
 	}
 
@@ -1610,19 +1657,17 @@
 			    struct serial_rs485 *rs485conf)
 {
 	struct imx_port *sport = (struct imx_port *)port;
+	unsigned long temp;
 
 	/* unimplemented */
 	rs485conf->delay_rts_before_send = 0;
 	rs485conf->delay_rts_after_send = 0;
-	rs485conf->flags |= SER_RS485_RX_DURING_TX;
 
 	/* RTS is required to control the transmitter */
 	if (!sport->have_rtscts)
 		rs485conf->flags &= ~SER_RS485_ENABLED;
 
 	if (rs485conf->flags & SER_RS485_ENABLED) {
-		unsigned long temp;
-
 		/* disable transmitter */
 		temp = readl(sport->port.membase + UCR2);
 		if (rs485conf->flags & SER_RS485_RTS_AFTER_SEND)
@@ -1632,6 +1677,14 @@
 		writel(temp, sport->port.membase + UCR2);
 	}
 
+	/* Make sure Rx is enabled in case Tx is active with Rx disabled */
+	if (!(rs485conf->flags & SER_RS485_ENABLED) ||
+	    rs485conf->flags & SER_RS485_RX_DURING_TX) {
+		temp = readl(sport->port.membase + UCR2);
+		temp |= UCR2_RXEN;
+		writel(temp, sport->port.membase + UCR2);
+	}
+
 	port->rs485 = *rs485conf;
 
 	return 0;
@@ -1927,7 +1980,8 @@
 	}
 	sport->port.line = ret;
 
-	if (of_get_property(np, "fsl,uart-has-rtscts", NULL))
+	if (of_get_property(np, "uart-has-rtscts", NULL) ||
+	    of_get_property(np, "fsl,uart-has-rtscts", NULL) /* deprecated */)
 		sport->have_rtscts = 1;
 
 	if (of_get_property(np, "fsl,dte-mode", NULL))
diff --git a/drivers/tty/serial/meson_uart.c b/drivers/tty/serial/meson_uart.c
index 024445a..6aea0f4 100644
--- a/drivers/tty/serial/meson_uart.c
+++ b/drivers/tty/serial/meson_uart.c
@@ -481,18 +481,13 @@
 	writel(ch, port->membase + AML_UART_WFIFO);
 }
 
-static void meson_serial_console_write(struct console *co, const char *s,
-				       u_int count)
+static void meson_serial_port_write(struct uart_port *port, const char *s,
+				    u_int count)
 {
-	struct uart_port *port;
 	unsigned long flags;
 	int locked;
 	u32 val, tmp;
 
-	port = meson_ports[co->index];
-	if (!port)
-		return;
-
 	local_irq_save(flags);
 	if (port->sysrq) {
 		locked = 0;
@@ -516,6 +511,18 @@
 	local_irq_restore(flags);
 }
 
+static void meson_serial_console_write(struct console *co, const char *s,
+				       u_int count)
+{
+	struct uart_port *port;
+
+	port = meson_ports[co->index];
+	if (!port)
+		return;
+
+	meson_serial_port_write(port, s, count);
+}
+
 static int meson_serial_console_setup(struct console *co, char *options)
 {
 	struct uart_port *port;
@@ -554,6 +561,27 @@
 }
 console_initcall(meson_serial_console_init);
 
+static void meson_serial_early_console_write(struct console *co,
+					     const char *s,
+					     u_int count)
+{
+	struct earlycon_device *dev = co->data;
+
+	meson_serial_port_write(&dev->port, s, count);
+}
+
+static int __init
+meson_serial_early_console_setup(struct earlycon_device *device, const char *opt)
+{
+	if (!device->port.membase)
+		return -ENODEV;
+
+	device->con->write = meson_serial_early_console_write;
+	return 0;
+}
+OF_EARLYCON_DECLARE(meson, "amlogic,meson-uart",
+		    meson_serial_early_console_setup);
+
 #define MESON_SERIAL_CONSOLE	(&meson_serial_console)
 #else
 #define MESON_SERIAL_CONSOLE	NULL
diff --git a/drivers/tty/serial/mps2-uart.c b/drivers/tty/serial/mps2-uart.c
new file mode 100644
index 0000000..da9e27d
--- /dev/null
+++ b/drivers/tty/serial/mps2-uart.c
@@ -0,0 +1,625 @@
+/*
+ * Copyright (C) 2015 ARM Limited
+ *
+ * Author: Vladimir Murzin <vladimir.murzin@arm.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * TODO: support for SysRq
+ */
+
+#define pr_fmt(fmt)	KBUILD_MODNAME ": " fmt
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/console.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/serial_core.h>
+#include <linux/tty_flip.h>
+#include <linux/types.h>
+
+#define SERIAL_NAME	"ttyMPS"
+#define DRIVER_NAME	"mps2-uart"
+#define MAKE_NAME(x)	(DRIVER_NAME # x)
+
+#define UARTn_DATA				0x00
+
+#define UARTn_STATE				0x04
+#define UARTn_STATE_TX_FULL			BIT(0)
+#define UARTn_STATE_RX_FULL			BIT(1)
+#define UARTn_STATE_TX_OVERRUN			BIT(2)
+#define UARTn_STATE_RX_OVERRUN			BIT(3)
+
+#define UARTn_CTRL				0x08
+#define UARTn_CTRL_TX_ENABLE			BIT(0)
+#define UARTn_CTRL_RX_ENABLE			BIT(1)
+#define UARTn_CTRL_TX_INT_ENABLE		BIT(2)
+#define UARTn_CTRL_RX_INT_ENABLE		BIT(3)
+#define UARTn_CTRL_TX_OVERRUN_INT_ENABLE	BIT(4)
+#define UARTn_CTRL_RX_OVERRUN_INT_ENABLE	BIT(5)
+
+#define UARTn_INT				0x0c
+#define UARTn_INT_TX				BIT(0)
+#define UARTn_INT_RX				BIT(1)
+#define UARTn_INT_TX_OVERRUN			BIT(2)
+#define UARTn_INT_RX_OVERRUN			BIT(3)
+
+#define UARTn_BAUDDIV				0x10
+#define UARTn_BAUDDIV_MASK			GENMASK(20, 0)
+
+/*
+ * Helpers to make typical enable/disable operations more readable.
+ */
+#define UARTn_CTRL_TX_GRP	(UARTn_CTRL_TX_ENABLE		 |\
+				 UARTn_CTRL_TX_INT_ENABLE	 |\
+				 UARTn_CTRL_TX_OVERRUN_INT_ENABLE)
+
+#define UARTn_CTRL_RX_GRP	(UARTn_CTRL_RX_ENABLE		 |\
+				 UARTn_CTRL_RX_INT_ENABLE	 |\
+				 UARTn_CTRL_RX_OVERRUN_INT_ENABLE)
+
+#define MPS2_MAX_PORTS		3
+
+struct mps2_uart_port {
+	struct uart_port port;
+	struct clk *clk;
+	unsigned int tx_irq;
+	unsigned int rx_irq;
+};
+
+static inline struct mps2_uart_port *to_mps2_port(struct uart_port *port)
+{
+	return container_of(port, struct mps2_uart_port, port);
+}
+
+static void mps2_uart_write8(struct uart_port *port, u8 val, unsigned int off)
+{
+	struct mps2_uart_port *mps_port = to_mps2_port(port);
+
+	writeb(val, mps_port->port.membase + off);
+}
+
+static u8 mps2_uart_read8(struct uart_port *port, unsigned int off)
+{
+	struct mps2_uart_port *mps_port = to_mps2_port(port);
+
+	return readb(mps_port->port.membase + off);
+}
+
+static void mps2_uart_write32(struct uart_port *port, u32 val, unsigned int off)
+{
+	struct mps2_uart_port *mps_port = to_mps2_port(port);
+
+	writel_relaxed(val, mps_port->port.membase + off);
+}
+
+static unsigned int mps2_uart_tx_empty(struct uart_port *port)
+{
+	u8 status = mps2_uart_read8(port, UARTn_STATE);
+
+	return (status & UARTn_STATE_TX_FULL) ? 0 : TIOCSER_TEMT;
+}
+
+static void mps2_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+}
+
+static unsigned int mps2_uart_get_mctrl(struct uart_port *port)
+{
+	return TIOCM_CAR | TIOCM_CTS | TIOCM_DSR;
+}
+
+static void mps2_uart_stop_tx(struct uart_port *port)
+{
+	u8 control = mps2_uart_read8(port, UARTn_CTRL);
+
+	control &= ~UARTn_CTRL_TX_INT_ENABLE;
+
+	mps2_uart_write8(port, control, UARTn_CTRL);
+}
+
+static void mps2_uart_tx_chars(struct uart_port *port)
+{
+	struct circ_buf *xmit = &port->state->xmit;
+
+	while (!(mps2_uart_read8(port, UARTn_STATE) & UARTn_STATE_TX_FULL)) {
+		if (port->x_char) {
+			mps2_uart_write8(port, port->x_char, UARTn_DATA);
+			port->x_char = 0;
+			port->icount.tx++;
+			continue;
+		}
+
+		if (uart_circ_empty(xmit) || uart_tx_stopped(port))
+			break;
+
+		mps2_uart_write8(port, xmit->buf[xmit->tail], UARTn_DATA);
+		xmit->tail = (xmit->tail + 1) % UART_XMIT_SIZE;
+		port->icount.tx++;
+	}
+
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(port);
+
+	if (uart_circ_empty(xmit))
+		mps2_uart_stop_tx(port);
+}
+
+static void mps2_uart_start_tx(struct uart_port *port)
+{
+	u8 control = mps2_uart_read8(port, UARTn_CTRL);
+
+	control |= UARTn_CTRL_TX_INT_ENABLE;
+
+	mps2_uart_write8(port, control, UARTn_CTRL);
+
+	/*
+	 * We've just unmasked the TX IRQ and now slow-starting via
+	 * polling; if there is enough data to fill up the internal
+	 * write buffer in one go, the TX IRQ should assert, at which
+	 * point we switch to fully interrupt-driven TX.
+	 */
+
+	mps2_uart_tx_chars(port);
+}
+
+static void mps2_uart_stop_rx(struct uart_port *port)
+{
+	u8 control = mps2_uart_read8(port, UARTn_CTRL);
+
+	control &= ~UARTn_CTRL_RX_GRP;
+
+	mps2_uart_write8(port, control, UARTn_CTRL);
+}
+
+static void mps2_uart_break_ctl(struct uart_port *port, int ctl)
+{
+}
+
+static void mps2_uart_rx_chars(struct uart_port *port)
+{
+	struct tty_port *tport = &port->state->port;
+
+	while (mps2_uart_read8(port, UARTn_STATE) & UARTn_STATE_RX_FULL) {
+		u8 rxdata = mps2_uart_read8(port, UARTn_DATA);
+
+		port->icount.rx++;
+		tty_insert_flip_char(&port->state->port, rxdata, TTY_NORMAL);
+	}
+
+	tty_flip_buffer_push(tport);
+}
+
+static irqreturn_t mps2_uart_rxirq(int irq, void *data)
+{
+	struct uart_port *port = data;
+	u8 irqflag = mps2_uart_read8(port, UARTn_INT);
+
+	if (unlikely(!(irqflag & UARTn_INT_RX)))
+		return IRQ_NONE;
+
+	spin_lock(&port->lock);
+
+	mps2_uart_write8(port, UARTn_INT_RX, UARTn_INT);
+	mps2_uart_rx_chars(port);
+
+	spin_unlock(&port->lock);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t mps2_uart_txirq(int irq, void *data)
+{
+	struct uart_port *port = data;
+	u8 irqflag = mps2_uart_read8(port, UARTn_INT);
+
+	if (unlikely(!(irqflag & UARTn_INT_TX)))
+		return IRQ_NONE;
+
+	spin_lock(&port->lock);
+
+	mps2_uart_write8(port, UARTn_INT_TX, UARTn_INT);
+	mps2_uart_tx_chars(port);
+
+	spin_unlock(&port->lock);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t mps2_uart_oerrirq(int irq, void *data)
+{
+	irqreturn_t handled = IRQ_NONE;
+	struct uart_port *port = data;
+	u8 irqflag = mps2_uart_read8(port, UARTn_INT);
+
+	spin_lock(&port->lock);
+
+	if (irqflag & UARTn_INT_RX_OVERRUN) {
+		struct tty_port *tport = &port->state->port;
+
+		mps2_uart_write8(port, UARTn_INT_RX_OVERRUN, UARTn_INT);
+		port->icount.overrun++;
+		tty_insert_flip_char(tport, 0, TTY_OVERRUN);
+		tty_flip_buffer_push(tport);
+		handled = IRQ_HANDLED;
+	}
+
+	/*
+	 * It's never been seen in practice and it never *should* happen since
+	 * we check if there is enough room in TX buffer before sending data.
+	 * So we keep this check in case something suspicious has happened.
+	 */
+	if (irqflag & UARTn_INT_TX_OVERRUN) {
+		mps2_uart_write8(port, UARTn_INT_TX_OVERRUN, UARTn_INT);
+		handled = IRQ_HANDLED;
+	}
+
+	spin_unlock(&port->lock);
+
+	return handled;
+}
+
+static int mps2_uart_startup(struct uart_port *port)
+{
+	struct mps2_uart_port *mps_port = to_mps2_port(port);
+	u8 control = mps2_uart_read8(port, UARTn_CTRL);
+	int ret;
+
+	control &= ~(UARTn_CTRL_RX_GRP | UARTn_CTRL_TX_GRP);
+
+	mps2_uart_write8(port, control, UARTn_CTRL);
+
+	ret = request_irq(mps_port->rx_irq, mps2_uart_rxirq, 0,
+			  MAKE_NAME(-rx), mps_port);
+	if (ret) {
+		dev_err(port->dev, "failed to register rxirq (%d)\n", ret);
+		return ret;
+	}
+
+	ret = request_irq(mps_port->tx_irq, mps2_uart_txirq, 0,
+			  MAKE_NAME(-tx), mps_port);
+	if (ret) {
+		dev_err(port->dev, "failed to register txirq (%d)\n", ret);
+		goto err_free_rxirq;
+	}
+
+	ret = request_irq(port->irq, mps2_uart_oerrirq, IRQF_SHARED,
+			  MAKE_NAME(-overrun), mps_port);
+
+	if (ret) {
+		dev_err(port->dev, "failed to register oerrirq (%d)\n", ret);
+		goto err_free_txirq;
+	}
+
+	control |= UARTn_CTRL_RX_GRP | UARTn_CTRL_TX_GRP;
+
+	mps2_uart_write8(port, control, UARTn_CTRL);
+
+	return 0;
+
+err_free_txirq:
+	free_irq(mps_port->tx_irq, mps_port);
+err_free_rxirq:
+	free_irq(mps_port->rx_irq, mps_port);
+
+	return ret;
+}
+
+static void mps2_uart_shutdown(struct uart_port *port)
+{
+	struct mps2_uart_port *mps_port = to_mps2_port(port);
+	u8 control = mps2_uart_read8(port, UARTn_CTRL);
+
+	control &= ~(UARTn_CTRL_RX_GRP | UARTn_CTRL_TX_GRP);
+
+	mps2_uart_write8(port, control, UARTn_CTRL);
+
+	free_irq(mps_port->rx_irq, mps_port);
+	free_irq(mps_port->tx_irq, mps_port);
+	free_irq(port->irq, mps_port);
+}
+
+static void
+mps2_uart_set_termios(struct uart_port *port, struct ktermios *termios,
+		      struct ktermios *old)
+{
+	unsigned long flags;
+	unsigned int baud, bauddiv;
+
+	termios->c_cflag &= ~(CRTSCTS | CMSPAR);
+	termios->c_cflag &= ~CSIZE;
+	termios->c_cflag |= CS8;
+	termios->c_cflag &= ~PARENB;
+	termios->c_cflag &= ~CSTOPB;
+
+	baud = uart_get_baud_rate(port, termios, old,
+			DIV_ROUND_CLOSEST(port->uartclk, UARTn_BAUDDIV_MASK),
+			DIV_ROUND_CLOSEST(port->uartclk, 16));
+
+	bauddiv = DIV_ROUND_CLOSEST(port->uartclk, baud);
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	uart_update_timeout(port, termios->c_cflag, baud);
+	mps2_uart_write32(port, bauddiv, UARTn_BAUDDIV);
+
+	spin_unlock_irqrestore(&port->lock, flags);
+
+	if (tty_termios_baud_rate(termios))
+		tty_termios_encode_baud_rate(termios, baud, baud);
+}
+
+static const char *mps2_uart_type(struct uart_port *port)
+{
+	return (port->type == PORT_MPS2UART) ? DRIVER_NAME : NULL;
+}
+
+static void mps2_uart_release_port(struct uart_port *port)
+{
+}
+
+static int mps2_uart_request_port(struct uart_port *port)
+{
+	return 0;
+}
+
+static void mps2_uart_config_port(struct uart_port *port, int type)
+{
+	if (type & UART_CONFIG_TYPE && !mps2_uart_request_port(port))
+		port->type = PORT_MPS2UART;
+}
+
+static int mps2_uart_verify_port(struct uart_port *port, struct serial_struct *serinfo)
+{
+	return -EINVAL;
+}
+
+static const struct uart_ops mps2_uart_pops = {
+	.tx_empty = mps2_uart_tx_empty,
+	.set_mctrl = mps2_uart_set_mctrl,
+	.get_mctrl = mps2_uart_get_mctrl,
+	.stop_tx = mps2_uart_stop_tx,
+	.start_tx = mps2_uart_start_tx,
+	.stop_rx = mps2_uart_stop_rx,
+	.break_ctl = mps2_uart_break_ctl,
+	.startup = mps2_uart_startup,
+	.shutdown = mps2_uart_shutdown,
+	.set_termios = mps2_uart_set_termios,
+	.type = mps2_uart_type,
+	.release_port = mps2_uart_release_port,
+	.request_port = mps2_uart_request_port,
+	.config_port = mps2_uart_config_port,
+	.verify_port = mps2_uart_verify_port,
+};
+
+static struct mps2_uart_port mps2_uart_ports[MPS2_MAX_PORTS];
+
+#ifdef CONFIG_SERIAL_MPS2_UART_CONSOLE
+static void mps2_uart_console_putchar(struct uart_port *port, int ch)
+{
+	while (mps2_uart_read8(port, UARTn_STATE) & UARTn_STATE_TX_FULL)
+		cpu_relax();
+
+	mps2_uart_write8(port, ch, UARTn_DATA);
+}
+
+static void mps2_uart_console_write(struct console *co, const char *s, unsigned int cnt)
+{
+	struct uart_port *port = &mps2_uart_ports[co->index].port;
+
+	uart_console_write(port, s, cnt, mps2_uart_console_putchar);
+}
+
+static int mps2_uart_console_setup(struct console *co, char *options)
+{
+	struct mps2_uart_port *mps_port;
+	int baud = 9600;
+	int bits = 8;
+	int parity = 'n';
+	int flow = 'n';
+
+	if (co->index < 0 || co->index >= MPS2_MAX_PORTS)
+		return -ENODEV;
+
+	mps_port = &mps2_uart_ports[co->index];
+
+	if (options)
+		uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+	return uart_set_options(&mps_port->port, co, baud, parity, bits, flow);
+}
+
+static struct uart_driver mps2_uart_driver;
+
+static struct console mps2_uart_console = {
+	.name = SERIAL_NAME,
+	.device = uart_console_device,
+	.write = mps2_uart_console_write,
+	.setup = mps2_uart_console_setup,
+	.flags = CON_PRINTBUFFER,
+	.index = -1,
+	.data = &mps2_uart_driver,
+};
+
+#define MPS2_SERIAL_CONSOLE (&mps2_uart_console)
+
+static void mps2_early_putchar(struct uart_port *port, int ch)
+{
+	while (readb(port->membase + UARTn_STATE) & UARTn_STATE_TX_FULL)
+		cpu_relax();
+
+	writeb((unsigned char)ch, port->membase + UARTn_DATA);
+}
+
+static void mps2_early_write(struct console *con, const char *s, unsigned int n)
+{
+	struct earlycon_device *dev = con->data;
+
+	uart_console_write(&dev->port, s, n, mps2_early_putchar);
+}
+
+static int __init mps2_early_console_setup(struct earlycon_device *device,
+					   const char *opt)
+{
+	if (!device->port.membase)
+		return -ENODEV;
+
+	device->con->write = mps2_early_write;
+
+	return 0;
+}
+
+OF_EARLYCON_DECLARE(mps2, "arm,mps2-uart", mps2_early_console_setup);
+
+#else
+#define MPS2_SERIAL_CONSOLE NULL
+#endif
+
+static struct uart_driver mps2_uart_driver = {
+	.driver_name = DRIVER_NAME,
+	.dev_name = SERIAL_NAME,
+	.nr = MPS2_MAX_PORTS,
+	.cons = MPS2_SERIAL_CONSOLE,
+};
+
+static struct mps2_uart_port *mps2_of_get_port(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	int id;
+
+	if (!np)
+		return NULL;
+
+	id = of_alias_get_id(np, "serial");
+	if (id < 0)
+		id = 0;
+
+	if (WARN_ON(id >= MPS2_MAX_PORTS))
+		return NULL;
+
+	mps2_uart_ports[id].port.line = id;
+	return &mps2_uart_ports[id];
+}
+
+static int mps2_init_port(struct mps2_uart_port *mps_port,
+			  struct platform_device *pdev)
+{
+	struct resource *res;
+	int ret;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	mps_port->port.membase = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(mps_port->port.membase))
+		return PTR_ERR(mps_port->port.membase);
+
+	mps_port->port.mapbase = res->start;
+	mps_port->port.mapsize = resource_size(res);
+
+	mps_port->rx_irq = platform_get_irq(pdev, 0);
+	mps_port->tx_irq = platform_get_irq(pdev, 1);
+	mps_port->port.irq = platform_get_irq(pdev, 2);
+
+	mps_port->port.iotype = UPIO_MEM;
+	mps_port->port.flags = UPF_BOOT_AUTOCONF;
+	mps_port->port.fifosize = 1;
+	mps_port->port.ops = &mps2_uart_pops;
+	mps_port->port.dev = &pdev->dev;
+
+	mps_port->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(mps_port->clk))
+		return PTR_ERR(mps_port->clk);
+
+	ret = clk_prepare_enable(mps_port->clk);
+	if (ret)
+		return ret;
+
+	mps_port->port.uartclk = clk_get_rate(mps_port->clk);
+
+	clk_disable_unprepare(mps_port->clk);
+
+	return ret;
+}
+
+static int mps2_serial_probe(struct platform_device *pdev)
+{
+	struct mps2_uart_port *mps_port;
+	int ret;
+
+	mps_port = mps2_of_get_port(pdev);
+	if (!mps_port)
+		return -ENODEV;
+
+	ret = mps2_init_port(mps_port, pdev);
+	if (ret)
+		return ret;
+
+	ret = uart_add_one_port(&mps2_uart_driver, &mps_port->port);
+	if (ret)
+		return ret;
+
+	platform_set_drvdata(pdev, mps_port);
+
+	return 0;
+}
+
+static int mps2_serial_remove(struct platform_device *pdev)
+{
+	struct mps2_uart_port *mps_port = platform_get_drvdata(pdev);
+
+	uart_remove_one_port(&mps2_uart_driver, &mps_port->port);
+
+	return 0;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id mps2_match[] = {
+	{ .compatible = "arm,mps2-uart", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, mps2_match);
+#endif
+
+static struct platform_driver mps2_serial_driver = {
+	.probe = mps2_serial_probe,
+	.remove = mps2_serial_remove,
+
+	.driver = {
+		.name = DRIVER_NAME,
+		.of_match_table = of_match_ptr(mps2_match),
+	},
+};
+
+static int __init mps2_uart_init(void)
+{
+	int ret;
+
+	ret = uart_register_driver(&mps2_uart_driver);
+	if (ret)
+		return ret;
+
+	ret = platform_driver_register(&mps2_serial_driver);
+	if (ret)
+		uart_unregister_driver(&mps2_uart_driver);
+
+	return ret;
+}
+module_init(mps2_uart_init);
+
+static void __exit mps2_uart_exit(void)
+{
+	platform_driver_unregister(&mps2_serial_driver);
+	uart_unregister_driver(&mps2_uart_driver);
+}
+module_exit(mps2_uart_exit);
+
+MODULE_AUTHOR("Vladimir Murzin <vladimir.murzin@arm.com>");
+MODULE_DESCRIPTION("MPS2 UART driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:" DRIVER_NAME);
diff --git a/drivers/tty/serial/msm_serial.c b/drivers/tty/serial/msm_serial.c
index 96d3ce8..b7d80bd 100644
--- a/drivers/tty/serial/msm_serial.c
+++ b/drivers/tty/serial/msm_serial.c
@@ -861,37 +861,72 @@
 };
 
 static const struct msm_baud_map *
-msm_find_best_baud(struct uart_port *port, unsigned int baud)
+msm_find_best_baud(struct uart_port *port, unsigned int baud,
+		   unsigned long *rate)
 {
-	unsigned int i, divisor;
-	const struct msm_baud_map *entry;
+	struct msm_port *msm_port = UART_TO_MSM(port);
+	unsigned int divisor, result;
+	unsigned long target, old, best_rate = 0, diff, best_diff = ULONG_MAX;
+	const struct msm_baud_map *entry, *end, *best;
 	static const struct msm_baud_map table[] = {
-		{ 1536, 0x00,  1 },
-		{  768, 0x11,  1 },
-		{  384, 0x22,  1 },
-		{  192, 0x33,  1 },
-		{   96, 0x44,  1 },
-		{   48, 0x55,  1 },
-		{   32, 0x66,  1 },
-		{   24, 0x77,  1 },
-		{   16, 0x88,  1 },
-		{   12, 0x99,  6 },
-		{    8, 0xaa,  6 },
-		{    6, 0xbb,  6 },
-		{    4, 0xcc,  6 },
-		{    3, 0xdd,  8 },
-		{    2, 0xee, 16 },
 		{    1, 0xff, 31 },
-		{    0, 0xff, 31 },
+		{    2, 0xee, 16 },
+		{    3, 0xdd,  8 },
+		{    4, 0xcc,  6 },
+		{    6, 0xbb,  6 },
+		{    8, 0xaa,  6 },
+		{   12, 0x99,  6 },
+		{   16, 0x88,  1 },
+		{   24, 0x77,  1 },
+		{   32, 0x66,  1 },
+		{   48, 0x55,  1 },
+		{   96, 0x44,  1 },
+		{  192, 0x33,  1 },
+		{  384, 0x22,  1 },
+		{  768, 0x11,  1 },
+		{ 1536, 0x00,  1 },
 	};
 
-	divisor = uart_get_divisor(port, baud);
+	best = table; /* Default to smallest divider */
+	target = clk_round_rate(msm_port->clk, 16 * baud);
+	divisor = DIV_ROUND_CLOSEST(target, 16 * baud);
 
-	for (i = 0, entry = table; i < ARRAY_SIZE(table); i++, entry++)
-		if (entry->divisor <= divisor)
-			break;
+	end = table + ARRAY_SIZE(table);
+	entry = table;
+	while (entry < end) {
+		if (entry->divisor <= divisor) {
+			result = target / entry->divisor / 16;
+			diff = abs(result - baud);
 
-	return entry; /* Default to smallest divider */
+			/* Keep track of best entry */
+			if (diff < best_diff) {
+				best_diff = diff;
+				best = entry;
+				best_rate = target;
+			}
+
+			if (result == baud)
+				break;
+		} else if (entry->divisor > divisor) {
+			old = target;
+			target = clk_round_rate(msm_port->clk, old + 1);
+			/*
+			 * The rate didn't get any faster so we can't do
+			 * better at dividing it down
+			 */
+			if (target == old)
+				break;
+
+			/* Start the divisor search over at this new rate */
+			entry = table;
+			divisor = DIV_ROUND_CLOSEST(target, 16 * baud);
+			continue;
+		}
+		entry++;
+	}
+
+	*rate = best_rate;
+	return best;
 }
 
 static int msm_set_baud_rate(struct uart_port *port, unsigned int baud,
@@ -900,22 +935,20 @@
 	unsigned int rxstale, watermark, mask;
 	struct msm_port *msm_port = UART_TO_MSM(port);
 	const struct msm_baud_map *entry;
-	unsigned long flags;
-
-	entry = msm_find_best_baud(port, baud);
-
-	msm_write(port, entry->code, UART_CSR);
-
-	if (baud > 460800)
-		port->uartclk = baud * 16;
+	unsigned long flags, rate;
 
 	flags = *saved_flags;
 	spin_unlock_irqrestore(&port->lock, flags);
 
-	clk_set_rate(msm_port->clk, port->uartclk);
+	entry = msm_find_best_baud(port, baud, &rate);
+	clk_set_rate(msm_port->clk, rate);
+	baud = rate / 16 / entry->divisor;
 
 	spin_lock_irqsave(&port->lock, flags);
 	*saved_flags = flags;
+	port->uartclk = rate;
+
+	msm_write(port, entry->code, UART_CSR);
 
 	/* RX stale watermark */
 	rxstale = entry->rxstale;
@@ -1577,8 +1610,6 @@
 		msm_port->pclk = devm_clk_get(&pdev->dev, "iface");
 		if (IS_ERR(msm_port->pclk))
 			return PTR_ERR(msm_port->pclk);
-
-		clk_set_rate(msm_port->clk, 1843200);
 	}
 
 	port->uartclk = clk_get_rate(msm_port->clk);
diff --git a/drivers/tty/serial/mvebu-uart.c b/drivers/tty/serial/mvebu-uart.c
index 0ff2781..ce362bd 100644
--- a/drivers/tty/serial/mvebu-uart.c
+++ b/drivers/tty/serial/mvebu-uart.c
@@ -1,5 +1,7 @@
 /*
 * ***************************************************************************
+* Marvell Armada-3700 Serial Driver
+* Author: Wilson Ding <dingwei@marvell.com>
 * Copyright (C) 2015 Marvell International Ltd.
 * ***************************************************************************
 * This program is free software: you can redistribute it and/or modify it
@@ -23,7 +25,6 @@
 #include <linux/init.h>
 #include <linux/io.h>
 #include <linux/iopoll.h>
-#include <linux/module.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
 #include <linux/of_device.h>
@@ -594,30 +595,18 @@
 	return 0;
 }
 
-static int mvebu_uart_remove(struct platform_device *pdev)
-{
-	struct mvebu_uart_data *data = platform_get_drvdata(pdev);
-
-	uart_remove_one_port(&mvebu_uart_driver, data->port);
-	data->port->private_data = NULL;
-	data->port->mapbase      = 0;
-	return 0;
-}
-
 /* Match table for of_platform binding */
 static const struct of_device_id mvebu_uart_of_match[] = {
 	{ .compatible = "marvell,armada-3700-uart", },
 	{}
 };
-MODULE_DEVICE_TABLE(of, mvebu_uart_of_match);
 
 static struct platform_driver mvebu_uart_platform_driver = {
 	.probe	= mvebu_uart_probe,
-	.remove	= mvebu_uart_remove,
 	.driver	= {
-		.owner	= THIS_MODULE,
 		.name  = "mvebu-uart",
 		.of_match_table = of_match_ptr(mvebu_uart_of_match),
+		.suppress_bind_attrs = true,
 	},
 };
 
@@ -635,16 +624,4 @@
 
 	return ret;
 }
-
-static void __exit mvebu_uart_exit(void)
-{
-	platform_driver_unregister(&mvebu_uart_platform_driver);
-	uart_unregister_driver(&mvebu_uart_driver);
-}
-
 arch_initcall(mvebu_uart_init);
-module_exit(mvebu_uart_exit);
-
-MODULE_AUTHOR("Wilson Ding <dingwei@marvell.com>");
-MODULE_DESCRIPTION("Marvell Armada-3700 Serial Driver");
-MODULE_LICENSE("GPL");
diff --git a/drivers/tty/serial/mxs-auart.c b/drivers/tty/serial/mxs-auart.c
index cd0414b..eb54e5c 100644
--- a/drivers/tty/serial/mxs-auart.c
+++ b/drivers/tty/serial/mxs-auart.c
@@ -1,17 +1,18 @@
 /*
- * Freescale STMP37XX/STMP378X Application UART driver
+ * Application UART driver for:
+ *	Freescale STMP37XX/STMP378X
+ *	Alphascale ASM9260
  *
  * Author: dmitry pervushin <dimka@embeddedalley.com>
  *
+ * Copyright 2014 Oleksij Rempel <linux@rempel-privat.de>
+ *	Provide Alphascale ASM9260 support.
  * Copyright 2008-2010 Freescale Semiconductor, Inc.
  * Copyright 2008 Embedded Alley Solutions, Inc All Rights Reserved.
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License
  * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
  */
 
 #if defined(CONFIG_SERIAL_MXS_AUART_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
@@ -51,30 +52,16 @@
 #define MXS_AUART_PORTS 5
 #define MXS_AUART_FIFO_SIZE		16
 
+#define SET_REG				0x4
+#define CLR_REG				0x8
+#define TOG_REG				0xc
+
 #define AUART_CTRL0			0x00000000
-#define AUART_CTRL0_SET			0x00000004
-#define AUART_CTRL0_CLR			0x00000008
-#define AUART_CTRL0_TOG			0x0000000c
 #define AUART_CTRL1			0x00000010
-#define AUART_CTRL1_SET			0x00000014
-#define AUART_CTRL1_CLR			0x00000018
-#define AUART_CTRL1_TOG			0x0000001c
 #define AUART_CTRL2			0x00000020
-#define AUART_CTRL2_SET			0x00000024
-#define AUART_CTRL2_CLR			0x00000028
-#define AUART_CTRL2_TOG			0x0000002c
 #define AUART_LINECTRL			0x00000030
-#define AUART_LINECTRL_SET		0x00000034
-#define AUART_LINECTRL_CLR		0x00000038
-#define AUART_LINECTRL_TOG		0x0000003c
 #define AUART_LINECTRL2			0x00000040
-#define AUART_LINECTRL2_SET		0x00000044
-#define AUART_LINECTRL2_CLR		0x00000048
-#define AUART_LINECTRL2_TOG		0x0000004c
 #define AUART_INTR			0x00000050
-#define AUART_INTR_SET			0x00000054
-#define AUART_INTR_CLR			0x00000058
-#define AUART_INTR_TOG			0x0000005c
 #define AUART_DATA			0x00000060
 #define AUART_STAT			0x00000070
 #define AUART_DEBUG			0x00000080
@@ -136,11 +123,301 @@
 #define AUART_STAT_FERR				(1 << 16)
 #define AUART_STAT_RXCOUNT_MASK			0xffff
 
+/*
+ * Start of Alphascale asm9260 defines
+ * This list contains only differences of existing bits
+ * between imx2x and asm9260
+ */
+#define ASM9260_HW_CTRL0			0x0000
+/*
+ * RW. Tell the UART to execute the RX DMA Command. The
+ * UART will clear this bit at the end of receive execution.
+ */
+#define ASM9260_BM_CTRL0_RXDMA_RUN		BIT(28)
+/* RW. 0 use FIFO for status register; 1 use DMA */
+#define ASM9260_BM_CTRL0_RXTO_SOURCE_STATUS	BIT(25)
+/*
+ * RW. RX TIMEOUT Enable. Valid for FIFO and DMA.
+ * Warning: If this bit is set to 0, the RX timeout will not affect receive DMA
+ * operation. If this bit is set to 1, a receive timeout will cause the receive
+ * DMA logic to terminate by filling the remaining DMA bytes with garbage data.
+ */
+#define ASM9260_BM_CTRL0_RXTO_ENABLE		BIT(24)
+/*
+ * RW. Receive Timeout Counter Value: number of 8-bit-time to wait before
+ * asserting timeout on the RX input. If the RXFIFO is not empty and the RX
+ * input is idle, then the watchdog counter will decrement each bit-time. Note
+ * 7-bit-time is added to the programmed value, so a value of zero will set
+ * the counter to 7-bit-time, a value of 0x1 gives 15-bit-time and so on. Also
+ * note that the counter is reloaded at the end of each frame, so if the frame
+ * is 10 bits long and the timeout counter value is zero, then timeout will
+ * occur (when FIFO is not empty) even if the RX input is not idle. The default
+ * value is 0x3 (31 bit-time).
+ */
+#define ASM9260_BM_CTRL0_RXTO_MASK		(0xff << 16)
+/* TIMEOUT = (100*7+1)*(1/BAUD) */
+#define ASM9260_BM_CTRL0_DEFAULT_RXTIMEOUT	(20 << 16)
+
+/* TX ctrl register */
+#define ASM9260_HW_CTRL1			0x0010
+/*
+ * RW. Tell the UART to execute the TX DMA Command. The
+ * UART will clear this bit at the end of transmit execution.
+ */
+#define ASM9260_BM_CTRL1_TXDMA_RUN		BIT(28)
+
+#define ASM9260_HW_CTRL2			0x0020
+/*
+ * RW. Receive Interrupt FIFO Level Select.
+ * The trigger points for the receive interrupt are as follows:
+ * ONE_EIGHTHS = 0x0 Trigger on FIFO full to at least 2 of 16 entries.
+ * ONE_QUARTER = 0x1 Trigger on FIFO full to at least 4 of 16 entries.
+ * ONE_HALF = 0x2 Trigger on FIFO full to at least 8 of 16 entries.
+ * THREE_QUARTERS = 0x3 Trigger on FIFO full to at least 12 of 16 entries.
+ * SEVEN_EIGHTHS = 0x4 Trigger on FIFO full to at least 14 of 16 entries.
+ */
+#define ASM9260_BM_CTRL2_RXIFLSEL		(7 << 20)
+#define ASM9260_BM_CTRL2_DEFAULT_RXIFLSEL	(3 << 20)
+/* RW. Same as RXIFLSEL */
+#define ASM9260_BM_CTRL2_TXIFLSEL		(7 << 16)
+#define ASM9260_BM_CTRL2_DEFAULT_TXIFLSEL	(2 << 16)
+/* RW. Set DTR. When this bit is 1, the output is 0. */
+#define ASM9260_BM_CTRL2_DTR			BIT(10)
+/* RW. Loop Back Enable */
+#define ASM9260_BM_CTRL2_LBE			BIT(7)
+#define ASM9260_BM_CTRL2_PORT_ENABLE		BIT(0)
+
+#define ASM9260_HW_LINECTRL			0x0030
+/*
+ * RW. Stick Parity Select. When bits 1, 2, and 7 of this register are set, the
+ * parity bit is transmitted and checked as a 0. When bits 1 and 7 are set,
+ * and bit 2 is 0, the parity bit is transmitted and checked as a 1. When this
+ * bit is cleared stick parity is disabled.
+ */
+#define ASM9260_BM_LCTRL_SPS			BIT(7)
+/* RW. Word length */
+#define ASM9260_BM_LCTRL_WLEN			(3 << 5)
+#define ASM9260_BM_LCTRL_CHRL_5			(0 << 5)
+#define ASM9260_BM_LCTRL_CHRL_6			(1 << 5)
+#define ASM9260_BM_LCTRL_CHRL_7			(2 << 5)
+#define ASM9260_BM_LCTRL_CHRL_8			(3 << 5)
+
+/*
+ * Interrupt register.
+ * contains the interrupt enables and the interrupt status bits
+ */
+#define ASM9260_HW_INTR				0x0040
+/* Tx FIFO EMPTY Raw Interrupt enable */
+#define ASM9260_BM_INTR_TFEIEN			BIT(27)
+/* Overrun Error Interrupt Enable. */
+#define ASM9260_BM_INTR_OEIEN			BIT(26)
+/* Break Error Interrupt Enable. */
+#define ASM9260_BM_INTR_BEIEN			BIT(25)
+/* Parity Error Interrupt Enable. */
+#define ASM9260_BM_INTR_PEIEN			BIT(24)
+/* Framing Error Interrupt Enable. */
+#define ASM9260_BM_INTR_FEIEN			BIT(23)
+
+/* nUARTDSR Modem Interrupt Enable. */
+#define ASM9260_BM_INTR_DSRMIEN			BIT(19)
+/* nUARTDCD Modem Interrupt Enable. */
+#define ASM9260_BM_INTR_DCDMIEN			BIT(18)
+/* nUARTRI Modem Interrupt Enable. */
+#define ASM9260_BM_INTR_RIMIEN			BIT(16)
+/* Auto-Boud Timeout */
+#define ASM9260_BM_INTR_ABTO			BIT(13)
+#define ASM9260_BM_INTR_ABEO			BIT(12)
+/* Tx FIFO EMPTY Raw Interrupt state */
+#define ASM9260_BM_INTR_TFEIS			BIT(11)
+/* Overrun Error */
+#define ASM9260_BM_INTR_OEIS			BIT(10)
+/* Break Error */
+#define ASM9260_BM_INTR_BEIS			BIT(9)
+/* Parity Error */
+#define ASM9260_BM_INTR_PEIS			BIT(8)
+/* Framing Error */
+#define ASM9260_BM_INTR_FEIS			BIT(7)
+#define ASM9260_BM_INTR_DSRMIS			BIT(3)
+#define ASM9260_BM_INTR_DCDMIS			BIT(2)
+#define ASM9260_BM_INTR_RIMIS			BIT(0)
+
+/*
+ * RW. In DMA mode, up to 4 Received/Transmit characters can be accessed at a
+ * time. In PIO mode, only one character can be accessed at a time. The status
+ * register contains the receive data flags and valid bits.
+ */
+#define ASM9260_HW_DATA				0x0050
+
+#define ASM9260_HW_STAT				0x0060
+/* RO. If 1, UARTAPP is present in this product. */
+#define ASM9260_BM_STAT_PRESENT			BIT(31)
+/* RO. If 1, HISPEED is present in this product. */
+#define ASM9260_BM_STAT_HISPEED			BIT(30)
+/* RO. Receive FIFO Full. */
+#define ASM9260_BM_STAT_RXFULL			BIT(26)
+
+/* RO. The UART Debug Register contains the state of the DMA signals. */
+#define ASM9260_HW_DEBUG			0x0070
+/* DMA Command Run Status */
+#define ASM9260_BM_DEBUG_TXDMARUN		BIT(5)
+#define ASM9260_BM_DEBUG_RXDMARUN		BIT(4)
+/* DMA Command End Status */
+#define ASM9260_BM_DEBUG_TXCMDEND		BIT(3)
+#define ASM9260_BM_DEBUG_RXCMDEND		BIT(2)
+/* DMA Request Status */
+#define ASM9260_BM_DEBUG_TXDMARQ		BIT(1)
+#define ASM9260_BM_DEBUG_RXDMARQ		BIT(0)
+
+#define ASM9260_HW_ILPR				0x0080
+
+#define ASM9260_HW_RS485CTRL			0x0090
+/*
+ * RW. This bit reverses the polarity of the direction control signal on the RTS
+ * (or DTR) pin.
+ * If 0, The direction control pin will be driven to logic ‘0’ when the
+ * transmitter has data to be sent. It will be driven to logic ‘1’ after the
+ * last bit of data has been transmitted.
+ */
+#define ASM9260_BM_RS485CTRL_ONIV		BIT(5)
+/* RW. Enable Auto Direction Control. */
+#define ASM9260_BM_RS485CTRL_DIR_CTRL		BIT(4)
+/*
+ * RW. If 0 and DIR_CTRL = 1, pin RTS is used for direction control.
+ * If 1 and DIR_CTRL = 1, pin DTR is used for direction control.
+ */
+#define ASM9260_BM_RS485CTRL_PINSEL		BIT(3)
+/* RW. Enable Auto Address Detect (AAD). */
+#define ASM9260_BM_RS485CTRL_AADEN		BIT(2)
+/* RW. Disable receiver. */
+#define ASM9260_BM_RS485CTRL_RXDIS		BIT(1)
+/* RW. Enable RS-485/EIA-485 Normal Multidrop Mode (NMM) */
+#define ASM9260_BM_RS485CTRL_RS485EN		BIT(0)
+
+#define ASM9260_HW_RS485ADRMATCH		0x00a0
+/* Contains the address match value. */
+#define ASM9260_BM_RS485ADRMATCH_MASK		(0xff << 0)
+
+#define ASM9260_HW_RS485DLY			0x00b0
+/*
+ * RW. Contains the direction control (RTS or DTR) delay value. This delay time
+ * is in periods of the baud clock.
+ */
+#define ASM9260_BM_RS485DLY_MASK		(0xff << 0)
+
+#define ASM9260_HW_AUTOBAUD			0x00c0
+/* WO. Auto-baud time-out interrupt clear bit. */
+#define ASM9260_BM_AUTOBAUD_TO_INT_CLR		BIT(9)
+/* WO. End of auto-baud interrupt clear bit. */
+#define ASM9260_BM_AUTOBAUD_EO_INT_CLR		BIT(8)
+/* Restart in case of timeout (counter restarts at next UART Rx falling edge) */
+#define ASM9260_BM_AUTOBAUD_AUTORESTART		BIT(2)
+/* Auto-baud mode select bit. 0 - Mode 0, 1 - Mode 1. */
+#define ASM9260_BM_AUTOBAUD_MODE		BIT(1)
+/*
+ * Auto-baud start (auto-baud is running). Auto-baud run bit. This bit is
+ * automatically cleared after auto-baud completion.
+ */
+#define ASM9260_BM_AUTOBAUD_START		BIT(0)
+
+#define ASM9260_HW_CTRL3			0x00d0
+#define ASM9260_BM_CTRL3_OUTCLK_DIV_MASK	(0xffff << 16)
+/*
+ * RW. Provide clk over OUTCLK pin. In case of asm9260 it can be configured on
+ * pins 137 and 144.
+ */
+#define ASM9260_BM_CTRL3_MASTERMODE		BIT(6)
+/* RW. Baud Rate Mode: 1 - Enable sync mode. 0 - async mode. */
+#define ASM9260_BM_CTRL3_SYNCMODE		BIT(4)
+/* RW. 1 - MSB bit send frist; 0 - LSB bit frist. */
+#define ASM9260_BM_CTRL3_MSBF			BIT(2)
+/* RW. 1 - sample rate = 8 x Baudrate; 0 - sample rate = 16 x Baudrate. */
+#define ASM9260_BM_CTRL3_BAUD8			BIT(1)
+/* RW. 1 - Set word length to 9bit. 0 - use ASM9260_BM_LCTRL_WLEN */
+#define ASM9260_BM_CTRL3_9BIT			BIT(0)
+
+#define ASM9260_HW_ISO7816_CTRL			0x00e0
+/* RW. Enable High Speed mode. */
+#define ASM9260_BM_ISO7816CTRL_HS		BIT(12)
+/* Disable Successive Receive NACK */
+#define ASM9260_BM_ISO7816CTRL_DS_NACK		BIT(8)
+#define ASM9260_BM_ISO7816CTRL_MAX_ITER_MASK	(0xff << 4)
+/* Receive NACK Inhibit */
+#define ASM9260_BM_ISO7816CTRL_INACK		BIT(3)
+#define ASM9260_BM_ISO7816CTRL_NEG_DATA		BIT(2)
+/* RW. 1 - ISO7816 mode; 0 - USART mode */
+#define ASM9260_BM_ISO7816CTRL_ENABLE		BIT(0)
+
+#define ASM9260_HW_ISO7816_ERRCNT		0x00f0
+/* Parity error counter. Will be cleared after reading */
+#define ASM9260_BM_ISO7816_NB_ERRORS_MASK	(0xff << 0)
+
+#define ASM9260_HW_ISO7816_STATUS		0x0100
+/* Max number of Repetitions Reached */
+#define ASM9260_BM_ISO7816_STAT_ITERATION	BIT(0)
+
+/* End of Alphascale asm9260 defines */
+
 static struct uart_driver auart_driver;
 
 enum mxs_auart_type {
 	IMX23_AUART,
 	IMX28_AUART,
+	ASM9260_AUART,
+};
+
+struct vendor_data {
+	const u16	*reg_offset;
+};
+
+enum {
+	REG_CTRL0,
+	REG_CTRL1,
+	REG_CTRL2,
+	REG_LINECTRL,
+	REG_LINECTRL2,
+	REG_INTR,
+	REG_DATA,
+	REG_STAT,
+	REG_DEBUG,
+	REG_VERSION,
+	REG_AUTOBAUD,
+
+	/* The size of the array - must be last */
+	REG_ARRAY_SIZE,
+};
+
+static const u16 mxs_asm9260_offsets[REG_ARRAY_SIZE] = {
+	[REG_CTRL0] = ASM9260_HW_CTRL0,
+	[REG_CTRL1] = ASM9260_HW_CTRL1,
+	[REG_CTRL2] = ASM9260_HW_CTRL2,
+	[REG_LINECTRL] = ASM9260_HW_LINECTRL,
+	[REG_INTR] = ASM9260_HW_INTR,
+	[REG_DATA] = ASM9260_HW_DATA,
+	[REG_STAT] = ASM9260_HW_STAT,
+	[REG_DEBUG] = ASM9260_HW_DEBUG,
+	[REG_AUTOBAUD] = ASM9260_HW_AUTOBAUD,
+};
+
+static const u16 mxs_stmp37xx_offsets[REG_ARRAY_SIZE] = {
+	[REG_CTRL0] = AUART_CTRL0,
+	[REG_CTRL1] = AUART_CTRL1,
+	[REG_CTRL2] = AUART_CTRL2,
+	[REG_LINECTRL] = AUART_LINECTRL,
+	[REG_LINECTRL2] = AUART_LINECTRL2,
+	[REG_INTR] = AUART_INTR,
+	[REG_DATA] = AUART_DATA,
+	[REG_STAT] = AUART_STAT,
+	[REG_DEBUG] = AUART_DEBUG,
+	[REG_VERSION] = AUART_VERSION,
+	[REG_AUTOBAUD] = AUART_AUTOBAUD,
+};
+
+static const struct vendor_data vendor_alphascale_asm9260 = {
+	.reg_offset = mxs_asm9260_offsets,
+};
+
+static const struct vendor_data vendor_freescale_stmp37xx = {
+	.reg_offset = mxs_stmp37xx_offsets,
 };
 
 struct mxs_auart_port {
@@ -153,8 +430,10 @@
 	unsigned long flags;
 	unsigned int mctrl_prev;
 	enum mxs_auart_type devtype;
+	const struct vendor_data *vendor;
 
 	struct clk *clk;
+	struct clk *clk_ahb;
 	struct device *dev;
 
 	/* for DMA */
@@ -174,6 +453,7 @@
 static const struct platform_device_id mxs_auart_devtype[] = {
 	{ .name = "mxs-auart-imx23", .driver_data = IMX23_AUART },
 	{ .name = "mxs-auart-imx28", .driver_data = IMX28_AUART },
+	{ .name = "as-auart-asm9260", .driver_data = ASM9260_AUART },
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(platform, mxs_auart_devtype);
@@ -185,6 +465,9 @@
 	}, {
 		.compatible = "fsl,imx23-auart",
 		.data = &mxs_auart_devtype[IMX23_AUART]
+	}, {
+		.compatible = "alphascale,asm9260-auart",
+		.data = &mxs_auart_devtype[ASM9260_AUART]
 	}, { /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, mxs_auart_dt_ids);
@@ -194,11 +477,54 @@
 	return s->devtype == IMX28_AUART;
 }
 
+static inline int is_asm9260_auart(struct mxs_auart_port *s)
+{
+	return s->devtype == ASM9260_AUART;
+}
+
 static inline bool auart_dma_enabled(struct mxs_auart_port *s)
 {
 	return s->flags & MXS_AUART_DMA_ENABLED;
 }
 
+static unsigned int mxs_reg_to_offset(const struct mxs_auart_port *uap,
+				      unsigned int reg)
+{
+	return uap->vendor->reg_offset[reg];
+}
+
+static unsigned int mxs_read(const struct mxs_auart_port *uap,
+			     unsigned int reg)
+{
+	void __iomem *addr = uap->port.membase + mxs_reg_to_offset(uap, reg);
+
+	return readl_relaxed(addr);
+}
+
+static void mxs_write(unsigned int val, struct mxs_auart_port *uap,
+		      unsigned int reg)
+{
+	void __iomem *addr = uap->port.membase + mxs_reg_to_offset(uap, reg);
+
+	writel_relaxed(val, addr);
+}
+
+static void mxs_set(unsigned int val, struct mxs_auart_port *uap,
+		    unsigned int reg)
+{
+	void __iomem *addr = uap->port.membase + mxs_reg_to_offset(uap, reg);
+
+	writel_relaxed(val, addr + SET_REG);
+}
+
+static void mxs_clr(unsigned int val, struct mxs_auart_port *uap,
+		    unsigned int reg)
+{
+	void __iomem *addr = uap->port.membase + mxs_reg_to_offset(uap, reg);
+
+	writel_relaxed(val, addr + CLR_REG);
+}
+
 static void mxs_auart_stop_tx(struct uart_port *u);
 
 #define to_auart_port(u) container_of(u, struct mxs_auart_port, port)
@@ -295,19 +621,16 @@
 	}
 
 
-	while (!(readl(s->port.membase + AUART_STAT) &
-		 AUART_STAT_TXFF)) {
+	while (!(mxs_read(s, REG_STAT) & AUART_STAT_TXFF)) {
 		if (s->port.x_char) {
 			s->port.icount.tx++;
-			writel(s->port.x_char,
-				     s->port.membase + AUART_DATA);
+			mxs_write(s->port.x_char, s, REG_DATA);
 			s->port.x_char = 0;
 			continue;
 		}
 		if (!uart_circ_empty(xmit) && !uart_tx_stopped(&s->port)) {
 			s->port.icount.tx++;
-			writel(xmit->buf[xmit->tail],
-				     s->port.membase + AUART_DATA);
+			mxs_write(xmit->buf[xmit->tail], s, REG_DATA);
 			xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
 		} else
 			break;
@@ -316,11 +639,9 @@
 		uart_write_wakeup(&s->port);
 
 	if (uart_circ_empty(&(s->port.state->xmit)))
-		writel(AUART_INTR_TXIEN,
-			     s->port.membase + AUART_INTR_CLR);
+		mxs_clr(AUART_INTR_TXIEN, s, REG_INTR);
 	else
-		writel(AUART_INTR_TXIEN,
-			     s->port.membase + AUART_INTR_SET);
+		mxs_set(AUART_INTR_TXIEN, s, REG_INTR);
 
 	if (uart_tx_stopped(&s->port))
 		mxs_auart_stop_tx(&s->port);
@@ -332,8 +653,8 @@
 	u32 stat;
 	u8 c;
 
-	c = readl(s->port.membase + AUART_DATA);
-	stat = readl(s->port.membase + AUART_STAT);
+	c = mxs_read(s, REG_DATA);
+	stat = mxs_read(s, REG_STAT);
 
 	flag = TTY_NORMAL;
 	s->port.icount.rx++;
@@ -368,7 +689,7 @@
 
 	uart_insert_char(&s->port, stat, AUART_STAT_OERR, c, flag);
 out:
-	writel(stat, s->port.membase + AUART_STAT);
+	mxs_write(stat, s, REG_STAT);
 }
 
 static void mxs_auart_rx_chars(struct mxs_auart_port *s)
@@ -376,13 +697,13 @@
 	u32 stat = 0;
 
 	for (;;) {
-		stat = readl(s->port.membase + AUART_STAT);
+		stat = mxs_read(s, REG_STAT);
 		if (stat & AUART_STAT_RXFE)
 			break;
 		mxs_auart_rx_char(s);
 	}
 
-	writel(stat, s->port.membase + AUART_STAT);
+	mxs_write(stat, s, REG_STAT);
 	tty_flip_buffer_push(&s->port.state->port);
 }
 
@@ -418,7 +739,7 @@
 {
 	struct mxs_auart_port *s = to_auart_port(u);
 
-	u32 ctrl = readl(u->membase + AUART_CTRL2);
+	u32 ctrl = mxs_read(s, REG_CTRL2);
 
 	ctrl &= ~(AUART_CTRL2_RTSEN | AUART_CTRL2_RTS);
 	if (mctrl & TIOCM_RTS) {
@@ -428,7 +749,7 @@
 			ctrl |= AUART_CTRL2_RTS;
 	}
 
-	writel(ctrl, u->membase + AUART_CTRL2);
+	mxs_write(ctrl, s, REG_CTRL2);
 
 	mctrl_gpio_set(s->gpios, mctrl);
 }
@@ -459,7 +780,7 @@
 static u32 mxs_auart_get_mctrl(struct uart_port *u)
 {
 	struct mxs_auart_port *s = to_auart_port(u);
-	u32 stat = readl(u->membase + AUART_STAT);
+	u32 stat = mxs_read(s, REG_STAT);
 	u32 mctrl = 0;
 
 	if (stat & AUART_STAT_CTS)
@@ -536,14 +857,14 @@
 
 	dma_unmap_sg(s->dev, &s->rx_sgl, 1, DMA_FROM_DEVICE);
 
-	stat = readl(s->port.membase + AUART_STAT);
+	stat = mxs_read(s, REG_STAT);
 	stat &= ~(AUART_STAT_OERR | AUART_STAT_BERR |
 			AUART_STAT_PERR | AUART_STAT_FERR);
 
 	count = stat & AUART_STAT_RXCOUNT_MASK;
 	tty_insert_flip_string(port, s->rx_dma_buf, count);
 
-	writel(stat, s->port.membase + AUART_STAT);
+	mxs_write(stat, s, REG_STAT);
 	tty_flip_buffer_push(port);
 
 	/* start the next DMA for RX. */
@@ -606,8 +927,8 @@
 static void mxs_auart_dma_exit(struct mxs_auart_port *s)
 {
 
-	writel(AUART_CTRL2_TXDMAE | AUART_CTRL2_RXDMAE | AUART_CTRL2_DMAONERR,
-		s->port.membase + AUART_CTRL2_CLR);
+	mxs_clr(AUART_CTRL2_TXDMAE | AUART_CTRL2_RXDMAE | AUART_CTRL2_DMAONERR,
+		s, REG_CTRL2);
 
 	mxs_auart_dma_exit_channel(s);
 	s->flags &= ~MXS_AUART_DMA_ENABLED;
@@ -666,7 +987,7 @@
 	cflag = termios->c_cflag;
 
 	ctrl = AUART_LINECTRL_FEN;
-	ctrl2 = readl(u->membase + AUART_CTRL2);
+	ctrl2 = mxs_read(s, REG_CTRL2);
 
 	/* byte size */
 	switch (cflag & CSIZE) {
@@ -754,15 +1075,24 @@
 	}
 
 	/* set baud rate */
-	baud_min = DIV_ROUND_UP(u->uartclk * 32, AUART_LINECTRL_BAUD_DIV_MAX);
-	baud_max = u->uartclk * 32 / AUART_LINECTRL_BAUD_DIV_MIN;
-	baud = uart_get_baud_rate(u, termios, old, baud_min, baud_max);
-	div = u->uartclk * 32 / baud;
+	if (is_asm9260_auart(s)) {
+		baud = uart_get_baud_rate(u, termios, old,
+					  u->uartclk * 4 / 0x3FFFFF,
+					  u->uartclk / 16);
+		div = u->uartclk * 4 / baud;
+	} else {
+		baud_min = DIV_ROUND_UP(u->uartclk * 32,
+					AUART_LINECTRL_BAUD_DIV_MAX);
+		baud_max = u->uartclk * 32 / AUART_LINECTRL_BAUD_DIV_MIN;
+		baud = uart_get_baud_rate(u, termios, old, baud_min, baud_max);
+		div = u->uartclk * 32 / baud;
+	}
+
 	ctrl |= AUART_LINECTRL_BAUD_DIVFRAC(div & 0x3F);
 	ctrl |= AUART_LINECTRL_BAUD_DIVINT(div >> 6);
+	mxs_write(ctrl, s, REG_LINECTRL);
 
-	writel(ctrl, u->membase + AUART_LINECTRL);
-	writel(ctrl2, u->membase + AUART_CTRL2);
+	mxs_write(ctrl2, s, REG_CTRL2);
 
 	uart_update_timeout(u, termios->c_cflag, baud);
 
@@ -771,8 +1101,8 @@
 		!test_and_set_bit(MXS_AUART_DMA_RX_READY, &s->flags)) {
 		if (!mxs_auart_dma_prep_rx(s)) {
 			/* Disable the normal RX interrupt. */
-			writel(AUART_INTR_RXIEN | AUART_INTR_RTIEN,
-					u->membase + AUART_INTR_CLR);
+			mxs_clr(AUART_INTR_RXIEN | AUART_INTR_RTIEN,
+				s, REG_INTR);
 		} else {
 			mxs_auart_dma_exit(s);
 			dev_err(s->dev, "We can not start up the DMA.\n");
@@ -802,16 +1132,13 @@
 	u32 istat;
 	struct mxs_auart_port *s = context;
 	u32 mctrl_temp = s->mctrl_prev;
-	u32 stat = readl(s->port.membase + AUART_STAT);
+	u32 stat = mxs_read(s, REG_STAT);
 
-	istat = readl(s->port.membase + AUART_INTR);
+	istat = mxs_read(s, REG_INTR);
 
 	/* ack irq */
-	writel(istat & (AUART_INTR_RTIS
-		| AUART_INTR_TXIS
-		| AUART_INTR_RXIS
-		| AUART_INTR_CTSMIS),
-			s->port.membase + AUART_INTR_CLR);
+	mxs_clr(istat & (AUART_INTR_RTIS | AUART_INTR_TXIS | AUART_INTR_RXIS
+		| AUART_INTR_CTSMIS), s, REG_INTR);
 
 	/*
 	 * Dealing with GPIO interrupt
@@ -827,8 +1154,7 @@
 		if (CTS_AT_AUART() && s->ms_irq_enabled)
 			uart_handle_cts_change(&s->port,
 					stat & AUART_STAT_CTS);
-		writel(AUART_INTR_CTSMIS,
-				s->port.membase + AUART_INTR_CLR);
+		mxs_clr(AUART_INTR_CTSMIS, s, REG_INTR);
 		istat &= ~AUART_INTR_CTSMIS;
 	}
 
@@ -846,44 +1172,44 @@
 	return IRQ_HANDLED;
 }
 
-static void mxs_auart_reset_deassert(struct uart_port *u)
+static void mxs_auart_reset_deassert(struct mxs_auart_port *s)
 {
 	int i;
 	unsigned int reg;
 
-	writel(AUART_CTRL0_SFTRST, u->membase + AUART_CTRL0_CLR);
+	mxs_clr(AUART_CTRL0_SFTRST, s, REG_CTRL0);
 
 	for (i = 0; i < 10000; i++) {
-		reg = readl(u->membase + AUART_CTRL0);
+		reg = mxs_read(s, REG_CTRL0);
 		if (!(reg & AUART_CTRL0_SFTRST))
 			break;
 		udelay(3);
 	}
-	writel(AUART_CTRL0_CLKGATE, u->membase + AUART_CTRL0_CLR);
+	mxs_clr(AUART_CTRL0_CLKGATE, s, REG_CTRL0);
 }
 
-static void mxs_auart_reset_assert(struct uart_port *u)
+static void mxs_auart_reset_assert(struct mxs_auart_port *s)
 {
 	int i;
 	u32 reg;
 
-	reg = readl(u->membase + AUART_CTRL0);
+	reg = mxs_read(s, REG_CTRL0);
 	/* if already in reset state, keep it untouched */
 	if (reg & AUART_CTRL0_SFTRST)
 		return;
 
-	writel(AUART_CTRL0_CLKGATE, u->membase + AUART_CTRL0_CLR);
-	writel(AUART_CTRL0_SFTRST, u->membase + AUART_CTRL0_SET);
+	mxs_clr(AUART_CTRL0_CLKGATE, s, REG_CTRL0);
+	mxs_set(AUART_CTRL0_SFTRST, s, REG_CTRL0);
 
 	for (i = 0; i < 1000; i++) {
-		reg = readl(u->membase + AUART_CTRL0);
+		reg = mxs_read(s, REG_CTRL0);
 		/* reset is finished when the clock is gated */
 		if (reg & AUART_CTRL0_CLKGATE)
 			return;
 		udelay(10);
 	}
 
-	dev_err(u->dev, "Failed to reset the unit.");
+	dev_err(s->dev, "Failed to reset the unit.");
 }
 
 static int mxs_auart_startup(struct uart_port *u)
@@ -896,17 +1222,17 @@
 		return ret;
 
 	if (uart_console(u)) {
-		writel(AUART_CTRL0_CLKGATE, u->membase + AUART_CTRL0_CLR);
+		mxs_clr(AUART_CTRL0_CLKGATE, s, REG_CTRL0);
 	} else {
 		/* reset the unit to a well known state */
-		mxs_auart_reset_assert(u);
-		mxs_auart_reset_deassert(u);
+		mxs_auart_reset_assert(s);
+		mxs_auart_reset_deassert(s);
 	}
 
-	writel(AUART_CTRL2_UARTEN, u->membase + AUART_CTRL2_SET);
+	mxs_set(AUART_CTRL2_UARTEN, s, REG_CTRL2);
 
-	writel(AUART_INTR_RXIEN | AUART_INTR_RTIEN | AUART_INTR_CTSMIEN,
-			u->membase + AUART_INTR);
+	mxs_write(AUART_INTR_RXIEN | AUART_INTR_RTIEN | AUART_INTR_CTSMIEN,
+		  s, REG_INTR);
 
 	/* Reset FIFO size (it could have changed if DMA was enabled) */
 	u->fifosize = MXS_AUART_FIFO_SIZE;
@@ -915,7 +1241,7 @@
 	 * Enable fifo so all four bytes of a DMA word are written to
 	 * output (otherwise, only the LSB is written, ie. 1 in 4 bytes)
 	 */
-	writel(AUART_LINECTRL_FEN, u->membase + AUART_LINECTRL_SET);
+	mxs_set(AUART_LINECTRL_FEN, s, REG_LINECTRL);
 
 	/* get initial status of modem lines */
 	mctrl_gpio_get(s->gpios, &s->mctrl_prev);
@@ -934,12 +1260,13 @@
 		mxs_auart_dma_exit(s);
 
 	if (uart_console(u)) {
-		writel(AUART_CTRL2_UARTEN, u->membase + AUART_CTRL2_CLR);
-		writel(AUART_INTR_RXIEN | AUART_INTR_RTIEN | AUART_INTR_CTSMIEN,
-				u->membase + AUART_INTR_CLR);
-		writel(AUART_CTRL0_CLKGATE, u->membase + AUART_CTRL0_SET);
+		mxs_clr(AUART_CTRL2_UARTEN, s, REG_CTRL2);
+
+		mxs_clr(AUART_INTR_RXIEN | AUART_INTR_RTIEN |
+			AUART_INTR_CTSMIEN, s, REG_INTR);
+		mxs_set(AUART_CTRL0_CLKGATE, s, REG_CTRL0);
 	} else {
-		mxs_auart_reset_assert(u);
+		mxs_auart_reset_assert(s);
 	}
 
 	clk_disable_unprepare(s->clk);
@@ -947,7 +1274,9 @@
 
 static unsigned int mxs_auart_tx_empty(struct uart_port *u)
 {
-	if ((readl(u->membase + AUART_STAT) &
+	struct mxs_auart_port *s = to_auart_port(u);
+
+	if ((mxs_read(s, REG_STAT) &
 		 (AUART_STAT_TXFE | AUART_STAT_BUSY)) == AUART_STAT_TXFE)
 		return TIOCSER_TEMT;
 
@@ -959,29 +1288,33 @@
 	struct mxs_auart_port *s = to_auart_port(u);
 
 	/* enable transmitter */
-	writel(AUART_CTRL2_TXE, u->membase + AUART_CTRL2_SET);
+	mxs_set(AUART_CTRL2_TXE, s, REG_CTRL2);
 
 	mxs_auart_tx_chars(s);
 }
 
 static void mxs_auart_stop_tx(struct uart_port *u)
 {
-	writel(AUART_CTRL2_TXE, u->membase + AUART_CTRL2_CLR);
+	struct mxs_auart_port *s = to_auart_port(u);
+
+	mxs_clr(AUART_CTRL2_TXE, s, REG_CTRL2);
 }
 
 static void mxs_auart_stop_rx(struct uart_port *u)
 {
-	writel(AUART_CTRL2_RXE, u->membase + AUART_CTRL2_CLR);
+	struct mxs_auart_port *s = to_auart_port(u);
+
+	mxs_clr(AUART_CTRL2_RXE, s, REG_CTRL2);
 }
 
 static void mxs_auart_break_ctl(struct uart_port *u, int ctl)
 {
+	struct mxs_auart_port *s = to_auart_port(u);
+
 	if (ctl)
-		writel(AUART_LINECTRL_BRK,
-			     u->membase + AUART_LINECTRL_SET);
+		mxs_set(AUART_LINECTRL_BRK, s, REG_LINECTRL);
 	else
-		writel(AUART_LINECTRL_BRK,
-			     u->membase + AUART_LINECTRL_CLR);
+		mxs_clr(AUART_LINECTRL_BRK, s, REG_LINECTRL);
 }
 
 static struct uart_ops mxs_auart_ops = {
@@ -1009,15 +1342,16 @@
 #ifdef CONFIG_SERIAL_MXS_AUART_CONSOLE
 static void mxs_auart_console_putchar(struct uart_port *port, int ch)
 {
+	struct mxs_auart_port *s = to_auart_port(port);
 	unsigned int to = 1000;
 
-	while (readl(port->membase + AUART_STAT) & AUART_STAT_TXFF) {
+	while (mxs_read(s, REG_STAT) & AUART_STAT_TXFF) {
 		if (!to--)
 			break;
 		udelay(1);
 	}
 
-	writel(ch, port->membase + AUART_DATA);
+	mxs_write(ch, s, REG_DATA);
 }
 
 static void
@@ -1037,18 +1371,16 @@
 	clk_enable(s->clk);
 
 	/* First save the CR then disable the interrupts */
-	old_ctrl2 = readl(port->membase + AUART_CTRL2);
-	old_ctrl0 = readl(port->membase + AUART_CTRL0);
+	old_ctrl2 = mxs_read(s, REG_CTRL2);
+	old_ctrl0 = mxs_read(s, REG_CTRL0);
 
-	writel(AUART_CTRL0_CLKGATE,
-		     port->membase + AUART_CTRL0_CLR);
-	writel(AUART_CTRL2_UARTEN | AUART_CTRL2_TXE,
-		     port->membase + AUART_CTRL2_SET);
+	mxs_clr(AUART_CTRL0_CLKGATE, s, REG_CTRL0);
+	mxs_set(AUART_CTRL2_UARTEN | AUART_CTRL2_TXE, s, REG_CTRL2);
 
 	uart_console_write(port, str, count, mxs_auart_console_putchar);
 
 	/* Finally, wait for transmitter to become empty ... */
-	while (readl(port->membase + AUART_STAT) & AUART_STAT_BUSY) {
+	while (mxs_read(s, REG_STAT) & AUART_STAT_BUSY) {
 		udelay(1);
 		if (!to--)
 			break;
@@ -1060,24 +1392,25 @@
 	 * unused, but that is better than to disable it while it is still
 	 * transmitting.
 	 */
-	if (!(readl(port->membase + AUART_STAT) & AUART_STAT_BUSY)) {
-		writel(old_ctrl0, port->membase + AUART_CTRL0);
-		writel(old_ctrl2, port->membase + AUART_CTRL2);
+	if (!(mxs_read(s, REG_STAT) & AUART_STAT_BUSY)) {
+		mxs_write(old_ctrl0, s, REG_CTRL0);
+		mxs_write(old_ctrl2, s, REG_CTRL2);
 	}
 
 	clk_disable(s->clk);
 }
 
 static void __init
-auart_console_get_options(struct uart_port *port, int *baud,
+auart_console_get_options(struct mxs_auart_port *s, int *baud,
 			  int *parity, int *bits)
 {
+	struct uart_port *port = &s->port;
 	unsigned int lcr_h, quot;
 
-	if (!(readl(port->membase + AUART_CTRL2) & AUART_CTRL2_UARTEN))
+	if (!(mxs_read(s, REG_CTRL2) & AUART_CTRL2_UARTEN))
 		return;
 
-	lcr_h = readl(port->membase + AUART_LINECTRL);
+	lcr_h = mxs_read(s, REG_LINECTRL);
 
 	*parity = 'n';
 	if (lcr_h & AUART_LINECTRL_PEN) {
@@ -1092,12 +1425,10 @@
 	else
 		*bits = 8;
 
-	quot = ((readl(port->membase + AUART_LINECTRL)
-			& AUART_LINECTRL_BAUD_DIVINT_MASK))
-			    >> (AUART_LINECTRL_BAUD_DIVINT_SHIFT - 6);
-	quot |= ((readl(port->membase + AUART_LINECTRL)
-			& AUART_LINECTRL_BAUD_DIVFRAC_MASK))
-				>> AUART_LINECTRL_BAUD_DIVFRAC_SHIFT;
+	quot = ((mxs_read(s, REG_LINECTRL) & AUART_LINECTRL_BAUD_DIVINT_MASK))
+		>> (AUART_LINECTRL_BAUD_DIVINT_SHIFT - 6);
+	quot |= ((mxs_read(s, REG_LINECTRL) & AUART_LINECTRL_BAUD_DIVFRAC_MASK))
+		>> AUART_LINECTRL_BAUD_DIVFRAC_SHIFT;
 	if (quot == 0)
 		quot = 1;
 
@@ -1132,7 +1463,7 @@
 	if (options)
 		uart_parse_options(options, &baud, &parity, &bits, &flow);
 	else
-		auart_console_get_options(&s->port, &baud, &parity, &bits);
+		auart_console_get_options(s, &baud, &parity, &bits);
 
 	ret = uart_set_options(&s->port, co, baud, parity, bits, flow);
 
@@ -1164,6 +1495,60 @@
 #endif
 };
 
+static void mxs_init_regs(struct mxs_auart_port *s)
+{
+	if (is_asm9260_auart(s))
+		s->vendor = &vendor_alphascale_asm9260;
+	else
+		s->vendor = &vendor_freescale_stmp37xx;
+}
+
+static int mxs_get_clks(struct mxs_auart_port *s,
+			struct platform_device *pdev)
+{
+	int err;
+
+	if (!is_asm9260_auart(s)) {
+		s->clk = devm_clk_get(&pdev->dev, NULL);
+		if (IS_ERR(s->clk))
+			return PTR_ERR(s->clk);
+
+		return 0;
+	}
+
+	s->clk = devm_clk_get(s->dev, "mod");
+	if (IS_ERR(s->clk)) {
+		dev_err(s->dev, "Failed to get \"mod\" clk\n");
+		return PTR_ERR(s->clk);
+	}
+
+	s->clk_ahb = devm_clk_get(s->dev, "ahb");
+	if (IS_ERR(s->clk_ahb)) {
+		dev_err(s->dev, "Failed to get \"ahb\" clk\n");
+		return PTR_ERR(s->clk_ahb);
+	}
+
+	err = clk_prepare_enable(s->clk_ahb);
+	if (err) {
+		dev_err(s->dev, "Failed to enable ahb_clk!\n");
+		return err;
+	}
+
+	err = clk_set_rate(s->clk, clk_get_rate(s->clk_ahb));
+	if (err) {
+		dev_err(s->dev, "Failed to set rate!\n");
+		return err;
+	}
+
+	err = clk_prepare_enable(s->clk);
+	if (err) {
+		dev_err(s->dev, "Failed to enable clk!\n");
+		return err;
+	}
+
+	return 0;
+}
+
 /*
  * This function returns 1 if pdev isn't a device instatiated by dt, 0 if it
  * could successfully get all information from dt or a negative errno.
@@ -1185,7 +1570,8 @@
 	}
 	s->port.line = ret;
 
-	if (of_get_property(np, "fsl,uart-has-rtscts", NULL))
+	if (of_get_property(np, "uart-has-rtscts", NULL) ||
+	    of_get_property(np, "fsl,uart-has-rtscts", NULL) /* deprecated */)
 		set_bit(MXS_AUART_RTSCTS, &s->flags);
 
 	return 0;
@@ -1269,6 +1655,9 @@
 	if (!s)
 		return -ENOMEM;
 
+	s->port.dev = &pdev->dev;
+	s->dev = &pdev->dev;
+
 	ret = serial_mxs_probe_dt(s, pdev);
 	if (ret > 0)
 		s->port.line = pdev->id < 0 ? 0 : pdev->id;
@@ -1280,15 +1669,14 @@
 		s->devtype = pdev->id_entry->driver_data;
 	}
 
-	s->clk = devm_clk_get(&pdev->dev, NULL);
-	if (IS_ERR(s->clk))
-		return PTR_ERR(s->clk);
+	ret = mxs_get_clks(s, pdev);
+	if (ret)
+		return ret;
 
 	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (!r)
 		return -ENXIO;
 
-
 	s->port.mapbase = r->start;
 	s->port.membase = ioremap(r->start, resource_size(r));
 	s->port.ops = &mxs_auart_ops;
@@ -1296,7 +1684,8 @@
 	s->port.fifosize = MXS_AUART_FIFO_SIZE;
 	s->port.uartclk = clk_get_rate(s->clk);
 	s->port.type = PORT_IMX;
-	s->port.dev = s->dev = &pdev->dev;
+
+	mxs_init_regs(s);
 
 	s->mctrl_prev = 0;
 
@@ -1327,16 +1716,21 @@
 
 	auart_port[s->port.line] = s;
 
-	mxs_auart_reset_deassert(&s->port);
+	mxs_auart_reset_deassert(s);
 
 	ret = uart_add_one_port(&auart_driver, &s->port);
 	if (ret)
 		goto out_free_gpio_irq;
 
-	version = readl(s->port.membase + AUART_VERSION);
-	dev_info(&pdev->dev, "Found APPUART %d.%d.%d\n",
-	       (version >> 24) & 0xff,
-	       (version >> 16) & 0xff, version & 0xffff);
+	/* ASM9260 don't have version reg */
+	if (is_asm9260_auart(s)) {
+		dev_info(&pdev->dev, "Found APPUART ASM9260\n");
+	} else {
+		version = mxs_read(s, REG_VERSION);
+		dev_info(&pdev->dev, "Found APPUART %d.%d.%d\n",
+			 (version >> 24) & 0xff,
+			 (version >> 16) & 0xff, version & 0xffff);
+	}
 
 	return 0;
 
diff --git a/drivers/tty/serial/samsung.c b/drivers/tty/serial/samsung.c
index ac7f8df..99bb231 100644
--- a/drivers/tty/serial/samsung.c
+++ b/drivers/tty/serial/samsung.c
@@ -1271,6 +1271,8 @@
 	/* check to see if we need  to change clock source */
 
 	if (ourport->baudclk != clk) {
+		clk_prepare_enable(clk);
+
 		s3c24xx_serial_setsource(port, clk_sel);
 
 		if (!IS_ERR(ourport->baudclk)) {
@@ -1278,8 +1280,6 @@
 			ourport->baudclk = ERR_PTR(-EINVAL);
 		}
 
-		clk_prepare_enable(clk);
-
 		ourport->baudclk = clk;
 		ourport->baudclk_rate = clk ? clk_get_rate(clk) : 0;
 	}
diff --git a/drivers/tty/serial/sc16is7xx.c b/drivers/tty/serial/sc16is7xx.c
index e639361..f36e6df 100644
--- a/drivers/tty/serial/sc16is7xx.c
+++ b/drivers/tty/serial/sc16is7xx.c
@@ -666,7 +666,7 @@
 	struct uart_port *port = &s->p[portno].port;
 
 	do {
-		unsigned int iir, msr, rxlen;
+		unsigned int iir, rxlen;
 
 		iir = sc16is7xx_port_read(port, SC16IS7XX_IIR_REG);
 		if (iir & SC16IS7XX_IIR_NO_INT_BIT)
@@ -683,12 +683,6 @@
 			if (rxlen)
 				sc16is7xx_handle_rx(port, rxlen, iir);
 			break;
-
-		case SC16IS7XX_IIR_CTSRTS_SRC:
-			msr = sc16is7xx_port_read(port, SC16IS7XX_MSR_REG);
-			uart_handle_cts_change(port,
-					       !!(msr & SC16IS7XX_MSR_DCTS_BIT));
-			break;
 		case SC16IS7XX_IIR_THRI_SRC:
 			sc16is7xx_handle_tx(port);
 			break;
@@ -1014,9 +1008,8 @@
 			      SC16IS7XX_EFCR_TXDISABLE_BIT,
 			      0);
 
-	/* Enable RX, TX, CTS change interrupts */
-	val = SC16IS7XX_IER_RDI_BIT | SC16IS7XX_IER_THRI_BIT |
-	      SC16IS7XX_IER_CTSI_BIT;
+	/* Enable RX, TX interrupts */
+	val = SC16IS7XX_IER_RDI_BIT | SC16IS7XX_IER_THRI_BIT;
 	sc16is7xx_port_write(port, SC16IS7XX_IER_REG, val);
 
 	return 0;
diff --git a/drivers/tty/serial/serial-tegra.c b/drivers/tty/serial/serial-tegra.c
index 1d6fc60..1dba671 100644
--- a/drivers/tty/serial/serial-tegra.c
+++ b/drivers/tty/serial/serial-tegra.c
@@ -206,10 +206,8 @@
 static void tegra_uart_set_mctrl(struct uart_port *u, unsigned int mctrl)
 {
 	struct tegra_uart_port *tup = to_tegra_uport(u);
-	unsigned long mcr;
 	int dtr_enable;
 
-	mcr = tup->mcr_shadow;
 	tup->rts_active = !!(mctrl & TIOCM_RTS);
 	set_rts(tup, tup->rts_active);
 
diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index a126a60..a333c59 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -64,6 +64,41 @@
 	return !!(uport->status & UPSTAT_DCD_ENABLE);
 }
 
+static inline struct uart_port *uart_port_ref(struct uart_state *state)
+{
+	if (atomic_add_unless(&state->refcount, 1, 0))
+		return state->uart_port;
+	return NULL;
+}
+
+static inline void uart_port_deref(struct uart_port *uport)
+{
+	if (uport && atomic_dec_and_test(&uport->state->refcount))
+		wake_up(&uport->state->remove_wait);
+}
+
+#define uart_port_lock(state, flags)					\
+	({								\
+		struct uart_port *__uport = uart_port_ref(state);	\
+		if (__uport)						\
+			spin_lock_irqsave(&__uport->lock, flags);	\
+		__uport;						\
+	})
+
+#define uart_port_unlock(uport, flags)					\
+	({								\
+		struct uart_port *__uport = uport;			\
+		if (__uport)						\
+			spin_unlock_irqrestore(&__uport->lock, flags);	\
+		uart_port_deref(__uport);				\
+	})
+
+static inline struct uart_port *uart_port_check(struct uart_state *state)
+{
+	lockdep_assert_held(&state->port.mutex);
+	return state->uart_port;
+}
+
 /*
  * This routine is used by the interrupt handler to schedule processing in
  * the software interrupt portion of the driver.
@@ -82,12 +117,13 @@
 static void uart_stop(struct tty_struct *tty)
 {
 	struct uart_state *state = tty->driver_data;
-	struct uart_port *port = state->uart_port;
+	struct uart_port *port;
 	unsigned long flags;
 
-	spin_lock_irqsave(&port->lock, flags);
-	port->ops->stop_tx(port);
-	spin_unlock_irqrestore(&port->lock, flags);
+	port = uart_port_lock(state, flags);
+	if (port)
+		port->ops->stop_tx(port);
+	uart_port_unlock(port, flags);
 }
 
 static void __uart_start(struct tty_struct *tty)
@@ -95,19 +131,19 @@
 	struct uart_state *state = tty->driver_data;
 	struct uart_port *port = state->uart_port;
 
-	if (!uart_tx_stopped(port))
+	if (port && !uart_tx_stopped(port))
 		port->ops->start_tx(port);
 }
 
 static void uart_start(struct tty_struct *tty)
 {
 	struct uart_state *state = tty->driver_data;
-	struct uart_port *port = state->uart_port;
+	struct uart_port *port;
 	unsigned long flags;
 
-	spin_lock_irqsave(&port->lock, flags);
+	port = uart_port_lock(state, flags);
 	__uart_start(tty);
-	spin_unlock_irqrestore(&port->lock, flags);
+	uart_port_unlock(port, flags);
 }
 
 static void
@@ -134,7 +170,7 @@
 static int uart_port_startup(struct tty_struct *tty, struct uart_state *state,
 		int init_hw)
 {
-	struct uart_port *uport = state->uart_port;
+	struct uart_port *uport = uart_port_check(state);
 	unsigned long page;
 	int retval = 0;
 
@@ -196,7 +232,7 @@
 	struct tty_port *port = &state->port;
 	int retval;
 
-	if (port->flags & ASYNC_INITIALIZED)
+	if (tty_port_initialized(port))
 		return 0;
 
 	/*
@@ -207,7 +243,7 @@
 
 	retval = uart_port_startup(tty, state, init_hw);
 	if (!retval) {
-		set_bit(ASYNCB_INITIALIZED, &port->flags);
+		tty_port_set_initialized(port, 1);
 		clear_bit(TTY_IO_ERROR, &tty->flags);
 	} else if (retval > 0)
 		retval = 0;
@@ -219,10 +255,12 @@
  * This routine will shutdown a serial port; interrupts are disabled, and
  * DTR is dropped if the hangup on close termio flag is on.  Calls to
  * uart_shutdown are serialised by the per-port semaphore.
+ *
+ * uport == NULL if uart_port has already been removed
  */
 static void uart_shutdown(struct tty_struct *tty, struct uart_state *state)
 {
-	struct uart_port *uport = state->uart_port;
+	struct uart_port *uport = uart_port_check(state);
 	struct tty_port *port = &state->port;
 
 	/*
@@ -231,11 +269,13 @@
 	if (tty)
 		set_bit(TTY_IO_ERROR, &tty->flags);
 
-	if (test_and_clear_bit(ASYNCB_INITIALIZED, &port->flags)) {
+	if (tty_port_initialized(port)) {
+		tty_port_set_initialized(port, 0);
+
 		/*
 		 * Turn off DTR and RTS early.
 		 */
-		if (uart_console(uport) && tty)
+		if (uport && uart_console(uport) && tty)
 			uport->cons->cflag = tty->termios.c_cflag;
 
 		if (!tty || C_HUPCL(tty))
@@ -249,7 +289,7 @@
 	 * a DCD drop (hangup) at just the right time.  Clear suspended bit so
 	 * we don't try to resume a port that has been shutdown.
 	 */
-	clear_bit(ASYNCB_SUSPENDED, &port->flags);
+	tty_port_set_suspended(port, 0);
 
 	/*
 	 * Free the transmit buffer page.
@@ -441,7 +481,7 @@
 static void uart_change_speed(struct tty_struct *tty, struct uart_state *state,
 					struct ktermios *old_termios)
 {
-	struct uart_port *uport = state->uart_port;
+	struct uart_port *uport = uart_port_check(state);
 	struct ktermios *termios;
 	int hw_stopped;
 
@@ -486,7 +526,7 @@
 static int uart_put_char(struct tty_struct *tty, unsigned char c)
 {
 	struct uart_state *state = tty->driver_data;
-	struct uart_port *port = state->uart_port;
+	struct uart_port *port;
 	struct circ_buf *circ;
 	unsigned long flags;
 	int ret = 0;
@@ -495,13 +535,13 @@
 	if (!circ->buf)
 		return 0;
 
-	spin_lock_irqsave(&port->lock, flags);
-	if (uart_circ_chars_free(circ) != 0) {
+	port = uart_port_lock(state, flags);
+	if (port && uart_circ_chars_free(circ) != 0) {
 		circ->buf[circ->head] = c;
 		circ->head = (circ->head + 1) & (UART_XMIT_SIZE - 1);
 		ret = 1;
 	}
-	spin_unlock_irqrestore(&port->lock, flags);
+	uart_port_unlock(port, flags);
 	return ret;
 }
 
@@ -528,14 +568,12 @@
 		return -EL3HLT;
 	}
 
-	port = state->uart_port;
 	circ = &state->xmit;
-
 	if (!circ->buf)
 		return 0;
 
-	spin_lock_irqsave(&port->lock, flags);
-	while (1) {
+	port = uart_port_lock(state, flags);
+	while (port) {
 		c = CIRC_SPACE_TO_END(circ->head, circ->tail, UART_XMIT_SIZE);
 		if (count < c)
 			c = count;
@@ -549,32 +587,33 @@
 	}
 
 	__uart_start(tty);
-	spin_unlock_irqrestore(&port->lock, flags);
-
+	uart_port_unlock(port, flags);
 	return ret;
 }
 
 static int uart_write_room(struct tty_struct *tty)
 {
 	struct uart_state *state = tty->driver_data;
+	struct uart_port *port;
 	unsigned long flags;
 	int ret;
 
-	spin_lock_irqsave(&state->uart_port->lock, flags);
+	port = uart_port_lock(state, flags);
 	ret = uart_circ_chars_free(&state->xmit);
-	spin_unlock_irqrestore(&state->uart_port->lock, flags);
+	uart_port_unlock(port, flags);
 	return ret;
 }
 
 static int uart_chars_in_buffer(struct tty_struct *tty)
 {
 	struct uart_state *state = tty->driver_data;
+	struct uart_port *port;
 	unsigned long flags;
 	int ret;
 
-	spin_lock_irqsave(&state->uart_port->lock, flags);
+	port = uart_port_lock(state, flags);
 	ret = uart_circ_chars_pending(&state->xmit);
-	spin_unlock_irqrestore(&state->uart_port->lock, flags);
+	uart_port_unlock(port, flags);
 	return ret;
 }
 
@@ -593,14 +632,15 @@
 		return;
 	}
 
-	port = state->uart_port;
 	pr_debug("uart_flush_buffer(%d) called\n", tty->index);
 
-	spin_lock_irqsave(&port->lock, flags);
+	port = uart_port_lock(state, flags);
+	if (!port)
+		return;
 	uart_circ_clear(&state->xmit);
 	if (port->ops->flush_buffer)
 		port->ops->flush_buffer(port);
-	spin_unlock_irqrestore(&port->lock, flags);
+	uart_port_unlock(port, flags);
 	tty_wakeup(tty);
 }
 
@@ -611,9 +651,13 @@
 static void uart_send_xchar(struct tty_struct *tty, char ch)
 {
 	struct uart_state *state = tty->driver_data;
-	struct uart_port *port = state->uart_port;
+	struct uart_port *port;
 	unsigned long flags;
 
+	port = uart_port_ref(state);
+	if (!port)
+		return;
+
 	if (port->ops->send_xchar)
 		port->ops->send_xchar(port, ch);
 	else {
@@ -623,14 +667,19 @@
 			port->ops->start_tx(port);
 		spin_unlock_irqrestore(&port->lock, flags);
 	}
+	uart_port_deref(port);
 }
 
 static void uart_throttle(struct tty_struct *tty)
 {
 	struct uart_state *state = tty->driver_data;
-	struct uart_port *port = state->uart_port;
+	struct uart_port *port;
 	upstat_t mask = 0;
 
+	port = uart_port_ref(state);
+	if (!port)
+		return;
+
 	if (I_IXOFF(tty))
 		mask |= UPSTAT_AUTOXOFF;
 	if (C_CRTSCTS(tty))
@@ -646,14 +695,20 @@
 
 	if (mask & UPSTAT_AUTOXOFF)
 		uart_send_xchar(tty, STOP_CHAR(tty));
+
+	uart_port_deref(port);
 }
 
 static void uart_unthrottle(struct tty_struct *tty)
 {
 	struct uart_state *state = tty->driver_data;
-	struct uart_port *port = state->uart_port;
+	struct uart_port *port;
 	upstat_t mask = 0;
 
+	port = uart_port_ref(state);
+	if (!port)
+		return;
+
 	if (I_IXOFF(tty))
 		mask |= UPSTAT_AUTOXOFF;
 	if (C_CRTSCTS(tty))
@@ -669,12 +724,15 @@
 
 	if (mask & UPSTAT_AUTOXOFF)
 		uart_send_xchar(tty, START_CHAR(tty));
+
+	uart_port_deref(port);
 }
 
-static void uart_get_info(struct tty_port *port, struct serial_struct *retinfo)
+static int uart_get_info(struct tty_port *port, struct serial_struct *retinfo)
 {
 	struct uart_state *state = container_of(port, struct uart_state, port);
-	struct uart_port *uport = state->uart_port;
+	struct uart_port *uport;
+	int ret = -ENODEV;
 
 	memset(retinfo, 0, sizeof(*retinfo));
 
@@ -683,6 +741,10 @@
 	 * occur as we go
 	 */
 	mutex_lock(&port->mutex);
+	uport = uart_port_check(state);
+	if (!uport)
+		goto out;
+
 	retinfo->type	    = uport->type;
 	retinfo->line	    = uport->line;
 	retinfo->port	    = uport->iobase;
@@ -701,7 +763,11 @@
 	retinfo->io_type         = uport->iotype;
 	retinfo->iomem_reg_shift = uport->regshift;
 	retinfo->iomem_base      = (void *)(unsigned long)uport->mapbase;
+
+	ret = 0;
+out:
 	mutex_unlock(&port->mutex);
+	return ret;
 }
 
 static int uart_get_info_user(struct tty_port *port,
@@ -709,7 +775,8 @@
 {
 	struct serial_struct tmp;
 
-	uart_get_info(port, &tmp);
+	if (uart_get_info(port, &tmp) < 0)
+		return -EIO;
 
 	if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
 		return -EFAULT;
@@ -720,13 +787,16 @@
 			 struct uart_state *state,
 			 struct serial_struct *new_info)
 {
-	struct uart_port *uport = state->uart_port;
+	struct uart_port *uport = uart_port_check(state);
 	unsigned long new_port;
 	unsigned int change_irq, change_port, closing_wait;
 	unsigned int old_custom_divisor, close_delay;
 	upf_t old_flags, new_flags;
 	int retval = 0;
 
+	if (!uport)
+		return -EIO;
+
 	new_port = new_info->port;
 	if (HIGH_BITS_OFFSET)
 		new_port += (unsigned long) new_info->port_high << HIGH_BITS_OFFSET;
@@ -886,7 +956,7 @@
 	retval = 0;
 	if (uport->type == PORT_UNKNOWN)
 		goto exit;
-	if (port->flags & ASYNC_INITIALIZED) {
+	if (tty_port_initialized(port)) {
 		if (((old_flags ^ uport->flags) & UPF_SPD_MASK) ||
 		    old_custom_divisor != uport->custom_divisor) {
 			/*
@@ -936,13 +1006,11 @@
  *	@tty: tty associated with the UART
  *	@state: UART being queried
  *	@value: returned modem value
- *
- *	Note: uart_ioctl protects us against hangups.
  */
 static int uart_get_lsr_info(struct tty_struct *tty,
 			struct uart_state *state, unsigned int __user *value)
 {
-	struct uart_port *uport = state->uart_port;
+	struct uart_port *uport = uart_port_check(state);
 	unsigned int result;
 
 	result = uport->ops->tx_empty(uport);
@@ -965,18 +1033,22 @@
 {
 	struct uart_state *state = tty->driver_data;
 	struct tty_port *port = &state->port;
-	struct uart_port *uport = state->uart_port;
+	struct uart_port *uport;
 	int result = -EIO;
 
 	mutex_lock(&port->mutex);
-	if (!(tty->flags & (1 << TTY_IO_ERROR))) {
+	uport = uart_port_check(state);
+	if (!uport)
+		goto out;
+
+	if (!tty_io_error(tty)) {
 		result = uport->mctrl;
 		spin_lock_irq(&uport->lock);
 		result |= uport->ops->get_mctrl(uport);
 		spin_unlock_irq(&uport->lock);
 	}
+out:
 	mutex_unlock(&port->mutex);
-
 	return result;
 }
 
@@ -984,15 +1056,20 @@
 uart_tiocmset(struct tty_struct *tty, unsigned int set, unsigned int clear)
 {
 	struct uart_state *state = tty->driver_data;
-	struct uart_port *uport = state->uart_port;
 	struct tty_port *port = &state->port;
+	struct uart_port *uport;
 	int ret = -EIO;
 
 	mutex_lock(&port->mutex);
-	if (!(tty->flags & (1 << TTY_IO_ERROR))) {
+	uport = uart_port_check(state);
+	if (!uport)
+		goto out;
+
+	if (!tty_io_error(tty)) {
 		uart_update_mctrl(uport, set, clear);
 		ret = 0;
 	}
+out:
 	mutex_unlock(&port->mutex);
 	return ret;
 }
@@ -1001,21 +1078,26 @@
 {
 	struct uart_state *state = tty->driver_data;
 	struct tty_port *port = &state->port;
-	struct uart_port *uport = state->uart_port;
+	struct uart_port *uport;
+	int ret = -EIO;
 
 	mutex_lock(&port->mutex);
+	uport = uart_port_check(state);
+	if (!uport)
+		goto out;
 
 	if (uport->type != PORT_UNKNOWN)
 		uport->ops->break_ctl(uport, break_state);
-
+	ret = 0;
+out:
 	mutex_unlock(&port->mutex);
-	return 0;
+	return ret;
 }
 
 static int uart_do_autoconfig(struct tty_struct *tty,struct uart_state *state)
 {
-	struct uart_port *uport = state->uart_port;
 	struct tty_port *port = &state->port;
+	struct uart_port *uport;
 	int flags, ret;
 
 	if (!capable(CAP_SYS_ADMIN))
@@ -1029,6 +1111,12 @@
 	if (mutex_lock_interruptible(&port->mutex))
 		return -ERESTARTSYS;
 
+	uport = uart_port_check(state);
+	if (!uport) {
+		ret = -EIO;
+		goto out;
+	}
+
 	ret = -EBUSY;
 	if (tty_port_users(port) == 1) {
 		uart_shutdown(tty, state);
@@ -1052,6 +1140,7 @@
 
 		ret = uart_startup(tty, state, 1);
 	}
+out:
 	mutex_unlock(&port->mutex);
 	return ret;
 }
@@ -1074,10 +1163,9 @@
  * FIXME: This wants extracting into a common all driver implementation
  * of TIOCMWAIT using tty_port.
  */
-static int
-uart_wait_modem_status(struct uart_state *state, unsigned long arg)
+static int uart_wait_modem_status(struct uart_state *state, unsigned long arg)
 {
-	struct uart_port *uport = state->uart_port;
+	struct uart_port *uport;
 	struct tty_port *port = &state->port;
 	DECLARE_WAITQUEUE(wait, current);
 	struct uart_icount cprev, cnow;
@@ -1086,6 +1174,9 @@
 	/*
 	 * note the counters on entry
 	 */
+	uport = uart_port_ref(state);
+	if (!uport)
+		return -EIO;
 	spin_lock_irq(&uport->lock);
 	memcpy(&cprev, &uport->icount, sizeof(struct uart_icount));
 	uart_enable_ms(uport);
@@ -1119,6 +1210,7 @@
 	}
 	__set_current_state(TASK_RUNNING);
 	remove_wait_queue(&port->delta_msr_wait, &wait);
+	uart_port_deref(uport);
 
 	return ret;
 }
@@ -1134,11 +1226,15 @@
 {
 	struct uart_state *state = tty->driver_data;
 	struct uart_icount cnow;
-	struct uart_port *uport = state->uart_port;
+	struct uart_port *uport;
 
+	uport = uart_port_ref(state);
+	if (!uport)
+		return -EIO;
 	spin_lock_irq(&uport->lock);
 	memcpy(&cnow, &uport->icount, sizeof(struct uart_icount));
 	spin_unlock_irq(&uport->lock);
+	uart_port_deref(uport);
 
 	icount->cts         = cnow.cts;
 	icount->dsr         = cnow.dsr;
@@ -1200,11 +1296,11 @@
  * Called via sys_ioctl.  We can use spin_lock_irq() here.
  */
 static int
-uart_ioctl(struct tty_struct *tty, unsigned int cmd,
-	   unsigned long arg)
+uart_ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg)
 {
 	struct uart_state *state = tty->driver_data;
 	struct tty_port *port = &state->port;
+	struct uart_port *uport;
 	void __user *uarg = (void __user *)arg;
 	int ret = -ENOIOCTLCMD;
 
@@ -1238,7 +1334,7 @@
 	if (ret != -ENOIOCTLCMD)
 		goto out;
 
-	if (tty->flags & (1 << TTY_IO_ERROR)) {
+	if (tty_io_error(tty)) {
 		ret = -EIO;
 		goto out;
 	}
@@ -1256,8 +1352,9 @@
 		goto out;
 
 	mutex_lock(&port->mutex);
+	uport = uart_port_check(state);
 
-	if (tty->flags & (1 << TTY_IO_ERROR)) {
+	if (!uport || tty_io_error(tty)) {
 		ret = -EIO;
 		goto out_up;
 	}
@@ -1273,19 +1370,17 @@
 		break;
 
 	case TIOCGRS485:
-		ret = uart_get_rs485_config(state->uart_port, uarg);
+		ret = uart_get_rs485_config(uport, uarg);
 		break;
 
 	case TIOCSRS485:
-		ret = uart_set_rs485_config(state->uart_port, uarg);
+		ret = uart_set_rs485_config(uport, uarg);
 		break;
-	default: {
-		struct uart_port *uport = state->uart_port;
+	default:
 		if (uport->ops->ioctl)
 			ret = uport->ops->ioctl(uport, cmd, arg);
 		break;
 	}
-	}
 out_up:
 	mutex_unlock(&port->mutex);
 out:
@@ -1295,24 +1390,29 @@
 static void uart_set_ldisc(struct tty_struct *tty)
 {
 	struct uart_state *state = tty->driver_data;
-	struct uart_port *uport = state->uart_port;
+	struct uart_port *uport;
 
-	if (uport->ops->set_ldisc) {
-		mutex_lock(&state->port.mutex);
+	mutex_lock(&state->port.mutex);
+	uport = uart_port_check(state);
+	if (uport && uport->ops->set_ldisc)
 		uport->ops->set_ldisc(uport, &tty->termios);
-		mutex_unlock(&state->port.mutex);
-	}
+	mutex_unlock(&state->port.mutex);
 }
 
 static void uart_set_termios(struct tty_struct *tty,
 						struct ktermios *old_termios)
 {
 	struct uart_state *state = tty->driver_data;
-	struct uart_port *uport = state->uart_port;
+	struct uart_port *uport;
 	unsigned int cflag = tty->termios.c_cflag;
 	unsigned int iflag_mask = IGNBRK|BRKINT|IGNPAR|PARMRK|INPCK;
 	bool sw_changed = false;
 
+	mutex_lock(&state->port.mutex);
+	uport = uart_port_check(state);
+	if (!uport)
+		goto out;
+
 	/*
 	 * Drivers doing software flow control also need to know
 	 * about changes to these input settings.
@@ -1335,12 +1435,10 @@
 	    tty->termios.c_ispeed == old_termios->c_ispeed &&
 	    ((tty->termios.c_iflag ^ old_termios->c_iflag) & iflag_mask) == 0 &&
 	    !sw_changed) {
-		return;
+		goto out;
 	}
 
-	mutex_lock(&state->port.mutex);
 	uart_change_speed(tty, state, old_termios);
-	mutex_unlock(&state->port.mutex);
 	/* reload cflag from termios; port driver may have overriden flags */
 	cflag = tty->termios.c_cflag;
 
@@ -1350,17 +1448,18 @@
 	/* Handle transition away from B0 status */
 	else if (!(old_termios->c_cflag & CBAUD) && (cflag & CBAUD)) {
 		unsigned int mask = TIOCM_DTR;
-		if (!(cflag & CRTSCTS) || !test_bit(TTY_THROTTLED, &tty->flags))
+		if (!(cflag & CRTSCTS) || !tty_throttled(tty))
 			mask |= TIOCM_RTS;
 		uart_set_mctrl(uport, mask);
 	}
+out:
+	mutex_unlock(&state->port.mutex);
 }
 
 /*
  * Calls to uart_close() are serialised via the tty_lock in
  *   drivers/tty/tty_io.c:tty_release()
  *   drivers/tty/tty_io.c:do_tty_hangup()
- * This runs from a workqueue and can sleep for a _short_ time only.
  */
 static void uart_close(struct tty_struct *tty, struct file *filp)
 {
@@ -1379,18 +1478,21 @@
 		return;
 	}
 
-	uport = state->uart_port;
 	port = &state->port;
 	pr_debug("uart_close(%d) called\n", tty->index);
 
-	if (!port->count || tty_port_close_start(port, tty, filp) == 0)
+	if (tty_port_close_start(port, tty, filp) == 0)
 		return;
 
+	mutex_lock(&port->mutex);
+	uport = uart_port_check(state);
+
 	/*
 	 * At this point, we stop accepting input.  To do this, we
 	 * disable the receive line status interrupts.
 	 */
-	if (port->flags & ASYNC_INITIALIZED) {
+	if (tty_port_initialized(port) &&
+	    !WARN(!uport, "detached port still initialized!\n")) {
 		spin_lock_irq(&uport->lock);
 		uport->ops->stop_rx(uport);
 		spin_unlock_irq(&uport->lock);
@@ -1402,7 +1504,6 @@
 		uart_wait_until_sent(tty, uport->timeout);
 	}
 
-	mutex_lock(&port->mutex);
 	uart_shutdown(tty, state);
 	tty_port_tty_set(port, NULL);
 
@@ -1413,17 +1514,17 @@
 		if (port->close_delay)
 			msleep_interruptible(jiffies_to_msecs(port->close_delay));
 		spin_lock_irq(&port->lock);
-	} else if (!uart_console(uport)) {
+	} else if (uport && !uart_console(uport)) {
 		spin_unlock_irq(&port->lock);
 		uart_change_pm(state, UART_PM_STATE_OFF);
 		spin_lock_irq(&port->lock);
 	}
+	spin_unlock_irq(&port->lock);
+	tty_port_set_active(port, 0);
 
 	/*
 	 * Wake up anyone trying to open this port.
 	 */
-	clear_bit(ASYNCB_NORMAL_ACTIVE, &port->flags);
-	spin_unlock_irq(&port->lock);
 	wake_up_interruptible(&port->open_wait);
 
 	mutex_unlock(&port->mutex);
@@ -1435,11 +1536,14 @@
 static void uart_wait_until_sent(struct tty_struct *tty, int timeout)
 {
 	struct uart_state *state = tty->driver_data;
-	struct uart_port *port = state->uart_port;
+	struct uart_port *port;
 	unsigned long char_time, expire;
 
-	if (port->type == PORT_UNKNOWN || port->fifosize == 0)
+	port = uart_port_ref(state);
+	if (!port || port->type == PORT_UNKNOWN || port->fifosize == 0) {
+		uart_port_deref(port);
 		return;
+	}
 
 	/*
 	 * Set the check interval to be 1/5 of the estimated time to
@@ -1485,6 +1589,7 @@
 		if (time_after(jiffies, expire))
 			break;
 	}
+	uart_port_deref(port);
 }
 
 /*
@@ -1496,20 +1601,24 @@
 {
 	struct uart_state *state = tty->driver_data;
 	struct tty_port *port = &state->port;
+	struct uart_port *uport;
 	unsigned long flags;
 
 	pr_debug("uart_hangup(%d)\n", tty->index);
 
 	mutex_lock(&port->mutex);
-	if (port->flags & ASYNC_NORMAL_ACTIVE) {
+	uport = uart_port_check(state);
+	WARN(!uport, "hangup of detached port!\n");
+
+	if (tty_port_active(port)) {
 		uart_flush_buffer(tty);
 		uart_shutdown(tty, state);
 		spin_lock_irqsave(&port->lock, flags);
 		port->count = 0;
-		clear_bit(ASYNCB_NORMAL_ACTIVE, &port->flags);
 		spin_unlock_irqrestore(&port->lock, flags);
+		tty_port_set_active(port, 0);
 		tty_port_tty_set(port, NULL);
-		if (!uart_console(state->uart_port))
+		if (uport && !uart_console(uport))
 			uart_change_pm(state, UART_PM_STATE_OFF);
 		wake_up_interruptible(&port->open_wait);
 		wake_up_interruptible(&port->delta_msr_wait);
@@ -1517,10 +1626,11 @@
 	mutex_unlock(&port->mutex);
 }
 
+/* uport == NULL if uart_port has already been removed */
 static void uart_port_shutdown(struct tty_port *port)
 {
 	struct uart_state *state = container_of(port, struct uart_state, port);
-	struct uart_port *uport = state->uart_port;
+	struct uart_port *uport = uart_port_check(state);
 
 	/*
 	 * clear delta_msr_wait queue to avoid mem leaks: we may free
@@ -1534,23 +1644,36 @@
 	/*
 	 * Free the IRQ and disable the port.
 	 */
-	uport->ops->shutdown(uport);
+	if (uport)
+		uport->ops->shutdown(uport);
 
 	/*
 	 * Ensure that the IRQ handler isn't running on another CPU.
 	 */
-	synchronize_irq(uport->irq);
+	if (uport)
+		synchronize_irq(uport->irq);
 }
 
 static int uart_carrier_raised(struct tty_port *port)
 {
 	struct uart_state *state = container_of(port, struct uart_state, port);
-	struct uart_port *uport = state->uart_port;
+	struct uart_port *uport;
 	int mctrl;
+
+	uport = uart_port_ref(state);
+	/*
+	 * Should never observe uport == NULL since checks for hangup should
+	 * abort the tty_port_block_til_ready() loop before checking for carrier
+	 * raised -- but report carrier raised if it does anyway so open will
+	 * continue and not sleep
+	 */
+	if (WARN_ON(!uport))
+		return 1;
 	spin_lock_irq(&uport->lock);
 	uart_enable_ms(uport);
 	mctrl = uport->ops->get_mctrl(uport);
 	spin_unlock_irq(&uport->lock);
+	uart_port_deref(uport);
 	if (mctrl & TIOCM_CAR)
 		return 1;
 	return 0;
@@ -1559,12 +1682,18 @@
 static void uart_dtr_rts(struct tty_port *port, int onoff)
 {
 	struct uart_state *state = container_of(port, struct uart_state, port);
-	struct uart_port *uport = state->uart_port;
+	struct uart_port *uport;
+
+	uport = uart_port_ref(state);
+	if (!uport)
+		return;
 
 	if (onoff)
 		uart_set_mctrl(uport, TIOCM_DTR | TIOCM_RTS);
 	else
 		uart_clear_mctrl(uport, TIOCM_DTR | TIOCM_RTS);
+
+	uart_port_deref(uport);
 }
 
 /*
@@ -1583,6 +1712,7 @@
 	int retval, line = tty->index;
 	struct uart_state *state = drv->state + line;
 	struct tty_port *port = &state->port;
+	struct uart_port *uport;
 
 	pr_debug("uart_open(%d) called\n", line);
 
@@ -1602,15 +1732,15 @@
 		goto end;
 	}
 
-	if (!state->uart_port || state->uart_port->flags & UPF_DEAD) {
+	uport = uart_port_check(state);
+	if (!uport || uport->flags & UPF_DEAD) {
 		retval = -ENXIO;
 		goto err_unlock;
 	}
 
 	tty->driver_data = state;
-	state->uart_port->state = state;
-	state->port.low_latency =
-		(state->uart_port->flags & UPF_LOW_LATENCY) ? 1 : 0;
+	uport->state = state;
+	port->low_latency = (uport->flags & UPF_LOW_LATENCY) ? 1 : 0;
 	tty_port_tty_set(port, tty);
 
 	/*
@@ -1649,13 +1779,15 @@
 	struct uart_state *state = drv->state + i;
 	struct tty_port *port = &state->port;
 	enum uart_pm_state pm_state;
-	struct uart_port *uport = state->uart_port;
+	struct uart_port *uport;
 	char stat_buf[32];
 	unsigned int status;
 	int mmio;
 
+	mutex_lock(&port->mutex);
+	uport = uart_port_check(state);
 	if (!uport)
-		return;
+		goto out;
 
 	mmio = uport->iotype >= UPIO_MEM;
 	seq_printf(m, "%d: uart:%s %s%08llX irq:%d",
@@ -1667,11 +1799,10 @@
 
 	if (uport->type == PORT_UNKNOWN) {
 		seq_putc(m, '\n');
-		return;
+		goto out;
 	}
 
 	if (capable(CAP_SYS_ADMIN)) {
-		mutex_lock(&port->mutex);
 		pm_state = state->pm_state;
 		if (pm_state != UART_PM_STATE_ON)
 			uart_change_pm(state, UART_PM_STATE_ON);
@@ -1680,7 +1811,6 @@
 		spin_unlock_irq(&uport->lock);
 		if (pm_state != UART_PM_STATE_ON)
 			uart_change_pm(state, pm_state);
-		mutex_unlock(&port->mutex);
 
 		seq_printf(m, " tx:%d rx:%d",
 				uport->icount.tx, uport->icount.rx);
@@ -1718,6 +1848,8 @@
 	seq_putc(m, '\n');
 #undef STATBIT
 #undef INFOBIT
+out:
+	mutex_unlock(&port->mutex);
 }
 
 static int uart_proc_show(struct seq_file *m, void *v)
@@ -1954,10 +2086,10 @@
 static void uart_change_pm(struct uart_state *state,
 			   enum uart_pm_state pm_state)
 {
-	struct uart_port *port = state->uart_port;
+	struct uart_port *port = uart_port_check(state);
 
 	if (state->pm_state != pm_state) {
-		if (port->ops->pm)
+		if (port && port->ops->pm)
 			port->ops->pm(port, pm_state, state->pm_state);
 		state->pm_state = pm_state;
 	}
@@ -2003,12 +2135,12 @@
 
 	uport->suspended = 1;
 
-	if (port->flags & ASYNC_INITIALIZED) {
+	if (tty_port_initialized(port)) {
 		const struct uart_ops *ops = uport->ops;
 		int tries;
 
-		set_bit(ASYNCB_SUSPENDED, &port->flags);
-		clear_bit(ASYNCB_INITIALIZED, &port->flags);
+		tty_port_set_suspended(port, 1);
+		tty_port_set_initialized(port, 0);
 
 		spin_lock_irq(&uport->lock);
 		ops->stop_tx(uport);
@@ -2088,7 +2220,7 @@
 			console_start(uport->cons);
 	}
 
-	if (port->flags & ASYNC_SUSPENDED) {
+	if (tty_port_suspended(port)) {
 		const struct uart_ops *ops = uport->ops;
 		int ret;
 
@@ -2107,7 +2239,7 @@
 				ops->set_mctrl(uport, uport->mctrl);
 				ops->start_tx(uport);
 				spin_unlock_irq(&uport->lock);
-				set_bit(ASYNCB_INITIALIZED, &port->flags);
+				tty_port_set_initialized(port, 1);
 			} else {
 				/*
 				 * Failed to resume - maybe hardware went away?
@@ -2118,7 +2250,7 @@
 			}
 		}
 
-		clear_bit(ASYNCB_SUSPENDED, &port->flags);
+		tty_port_set_suspended(port, 0);
 	}
 
 	mutex_unlock(&port->mutex);
@@ -2228,42 +2360,42 @@
 {
 	struct uart_driver *drv = driver->driver_state;
 	struct uart_state *state = drv->state + line;
+	struct tty_port *tport;
 	struct uart_port *port;
 	int baud = 9600;
 	int bits = 8;
 	int parity = 'n';
 	int flow = 'n';
-	int ret;
+	int ret = 0;
 
-	if (!state || !state->uart_port)
+	if (!state)
 		return -1;
 
-	port = state->uart_port;
-	if (!(port->ops->poll_get_char && port->ops->poll_put_char))
-		return -1;
+	tport = &state->port;
+	mutex_lock(&tport->mutex);
+
+	port = uart_port_check(state);
+	if (!port || !(port->ops->poll_get_char && port->ops->poll_put_char)) {
+		ret = -1;
+		goto out;
+	}
 
 	if (port->ops->poll_init) {
-		struct tty_port *tport = &state->port;
-
-		ret = 0;
-		mutex_lock(&tport->mutex);
 		/*
-		 * We don't set ASYNCB_INITIALIZED as we only initialized the
-		 * hw, e.g. state->xmit is still uninitialized.
+		 * We don't set initialized as we only initialized the hw,
+		 * e.g. state->xmit is still uninitialized.
 		 */
-		if (!test_bit(ASYNCB_INITIALIZED, &tport->flags))
+		if (!tty_port_initialized(tport))
 			ret = port->ops->poll_init(port);
-		mutex_unlock(&tport->mutex);
-		if (ret)
-			return ret;
 	}
 
-	if (options) {
+	if (!ret && options) {
 		uart_parse_options(options, &baud, &parity, &bits, &flow);
-		return uart_set_options(port, NULL, baud, parity, bits, flow);
+		ret = uart_set_options(port, NULL, baud, parity, bits, flow);
 	}
-
-	return 0;
+out:
+	mutex_unlock(&tport->mutex);
+	return ret;
 }
 
 static int uart_poll_get_char(struct tty_driver *driver, int line)
@@ -2271,12 +2403,15 @@
 	struct uart_driver *drv = driver->driver_state;
 	struct uart_state *state = drv->state + line;
 	struct uart_port *port;
+	int ret = -1;
 
-	if (!state || !state->uart_port)
-		return -1;
-
-	port = state->uart_port;
-	return port->ops->poll_get_char(port);
+	if (state) {
+		port = uart_port_ref(state);
+		if (port)
+			ret = port->ops->poll_get_char(port);
+		uart_port_deref(port);
+	}
+	return ret;
 }
 
 static void uart_poll_put_char(struct tty_driver *driver, int line, char ch)
@@ -2285,14 +2420,17 @@
 	struct uart_state *state = drv->state + line;
 	struct uart_port *port;
 
-	if (!state || !state->uart_port)
+	if (!state)
 		return;
 
-	port = state->uart_port;
+	port = uart_port_ref(state);
+	if (!port)
+		return;
 
 	if (ch == '\n')
 		port->ops->poll_put_char(port, '\r');
 	port->ops->poll_put_char(port, ch);
+	uart_port_deref(port);
 }
 #endif
 
@@ -2639,6 +2777,8 @@
 	}
 
 	/* Link the port to the driver state table and vice versa */
+	atomic_set(&state->refcount, 1);
+	init_waitqueue_head(&state->remove_wait);
 	state->uart_port = uport;
 	uport->state = state;
 
@@ -2711,15 +2851,12 @@
 {
 	struct uart_state *state = drv->state + uport->line;
 	struct tty_port *port = &state->port;
+	struct uart_port *uart_port;
 	struct tty_struct *tty;
 	int ret = 0;
 
 	BUG_ON(in_interrupt());
 
-	if (state->uart_port != uport)
-		dev_alert(uport->dev, "Removing wrong port: %p != %p\n",
-			state->uart_port, uport);
-
 	mutex_lock(&port_mutex);
 
 	/*
@@ -2727,7 +2864,12 @@
 	 * succeeding while we shut down the port.
 	 */
 	mutex_lock(&port->mutex);
-	if (!state->uart_port) {
+	uart_port = uart_port_check(state);
+	if (uart_port != uport)
+		dev_alert(uport->dev, "Removing wrong port: %p != %p\n",
+			  uart_port, uport);
+
+	if (!uart_port) {
 		mutex_unlock(&port->mutex);
 		ret = -EINVAL;
 		goto out;
@@ -2764,7 +2906,11 @@
 	 */
 	uport->type = PORT_UNKNOWN;
 
+	mutex_lock(&port->mutex);
+	WARN_ON(atomic_dec_return(&state->refcount) < 0);
+	wait_event(state->remove_wait, !atomic_read(&state->refcount));
 	state->uart_port = NULL;
+	mutex_unlock(&port->mutex);
 out:
 	mutex_unlock(&port_mutex);
 
diff --git a/drivers/tty/serial/serial_mctrl_gpio.c b/drivers/tty/serial/serial_mctrl_gpio.c
index 0214736..e8dd509 100644
--- a/drivers/tty/serial/serial_mctrl_gpio.c
+++ b/drivers/tty/serial/serial_mctrl_gpio.c
@@ -43,8 +43,6 @@
 	{ "rng", TIOCM_RNG, false, },
 	{ "rts", TIOCM_RTS, true, },
 	{ "dtr", TIOCM_DTR, true, },
-	{ "out1", TIOCM_OUT1, true, },
-	{ "out2", TIOCM_OUT2, true, },
 };
 
 void mctrl_gpio_set(struct mctrl_gpios *gpios, unsigned int mctrl)
@@ -125,9 +123,12 @@
 	struct uart_port *port = gpios->port;
 	u32 mctrl = gpios->mctrl_prev;
 	u32 mctrl_diff;
+	unsigned long flags;
 
 	mctrl_gpio_get(gpios, &mctrl);
 
+	spin_lock_irqsave(&port->lock, flags);
+
 	mctrl_diff = mctrl ^ gpios->mctrl_prev;
 	gpios->mctrl_prev = mctrl;
 
@@ -147,6 +148,8 @@
 		wake_up_interruptible(&port->state->port.delta_msr_wait);
 	}
 
+	spin_unlock_irqrestore(&port->lock, flags);
+
 	return IRQ_HANDLED;
 }
 
diff --git a/drivers/tty/serial/serial_mctrl_gpio.h b/drivers/tty/serial/serial_mctrl_gpio.h
index bcfad5d..332a33a 100644
--- a/drivers/tty/serial/serial_mctrl_gpio.h
+++ b/drivers/tty/serial/serial_mctrl_gpio.h
@@ -32,8 +32,6 @@
 	UART_GPIO_RI = UART_GPIO_RNG,
 	UART_GPIO_RTS,
 	UART_GPIO_DTR,
-	UART_GPIO_OUT1,
-	UART_GPIO_OUT2,
 	UART_GPIO_MAX,
 };
 
diff --git a/drivers/tty/serial/sirfsoc_uart.c b/drivers/tty/serial/sirfsoc_uart.c
index c6657de..b186c9c 100644
--- a/drivers/tty/serial/sirfsoc_uart.c
+++ b/drivers/tty/serial/sirfsoc_uart.c
@@ -1264,6 +1264,7 @@
 
 static int sirfsoc_uart_probe(struct platform_device *pdev)
 {
+	struct device_node *np = pdev->dev.of_node;
 	struct sirfsoc_uart_port *sirfport;
 	struct uart_port *port;
 	struct resource *res;
@@ -1276,13 +1277,13 @@
 	};
 	const struct of_device_id *match;
 
-	match = of_match_node(sirfsoc_uart_ids, pdev->dev.of_node);
+	match = of_match_node(sirfsoc_uart_ids, np);
 	sirfport = devm_kzalloc(&pdev->dev, sizeof(*sirfport), GFP_KERNEL);
 	if (!sirfport) {
 		ret = -ENOMEM;
 		goto err;
 	}
-	sirfport->port.line = of_alias_get_id(pdev->dev.of_node, "serial");
+	sirfport->port.line = of_alias_get_id(np, "serial");
 	sirf_ports[sirfport->port.line] = sirfport;
 	sirfport->port.iotype = UPIO_MEM;
 	sirfport->port.flags = UPF_BOOT_AUTOCONF;
@@ -1291,25 +1292,25 @@
 	port->private_data = sirfport;
 	sirfport->uart_reg = (struct sirfsoc_uart_register *)match->data;
 
-	sirfport->hw_flow_ctrl = of_property_read_bool(pdev->dev.of_node,
-		"sirf,uart-has-rtscts");
-	if (of_device_is_compatible(pdev->dev.of_node, "sirf,prima2-uart") ||
-		of_device_is_compatible(pdev->dev.of_node, "sirf,atlas7-uart"))
+	sirfport->hw_flow_ctrl =
+		of_property_read_bool(np, "uart-has-rtscts") ||
+		of_property_read_bool(np, "sirf,uart-has-rtscts") /* deprecated */;
+	if (of_device_is_compatible(np, "sirf,prima2-uart") ||
+		of_device_is_compatible(np, "sirf,atlas7-uart"))
 		sirfport->uart_reg->uart_type = SIRF_REAL_UART;
-	if (of_device_is_compatible(pdev->dev.of_node,
-		"sirf,prima2-usp-uart") || of_device_is_compatible(
-		pdev->dev.of_node, "sirf,atlas7-usp-uart")) {
+	if (of_device_is_compatible(np, "sirf,prima2-usp-uart") ||
+	    of_device_is_compatible(np, "sirf,atlas7-usp-uart")) {
 		sirfport->uart_reg->uart_type =	SIRF_USP_UART;
 		if (!sirfport->hw_flow_ctrl)
 			goto usp_no_flow_control;
-		if (of_find_property(pdev->dev.of_node, "cts-gpios", NULL))
-			sirfport->cts_gpio = of_get_named_gpio(
-					pdev->dev.of_node, "cts-gpios", 0);
+		if (of_find_property(np, "cts-gpios", NULL))
+			sirfport->cts_gpio =
+				of_get_named_gpio(np, "cts-gpios", 0);
 		else
 			sirfport->cts_gpio = -1;
-		if (of_find_property(pdev->dev.of_node, "rts-gpios", NULL))
-			sirfport->rts_gpio = of_get_named_gpio(
-					pdev->dev.of_node, "rts-gpios", 0);
+		if (of_find_property(np, "rts-gpios", NULL))
+			sirfport->rts_gpio =
+				of_get_named_gpio(np, "rts-gpios", 0);
 		else
 			sirfport->rts_gpio = -1;
 
@@ -1336,13 +1337,11 @@
 		gpio_direction_output(sirfport->rts_gpio, 1);
 	}
 usp_no_flow_control:
-	if (of_device_is_compatible(pdev->dev.of_node, "sirf,atlas7-uart") ||
-	    of_device_is_compatible(pdev->dev.of_node, "sirf,atlas7-usp-uart"))
+	if (of_device_is_compatible(np, "sirf,atlas7-uart") ||
+	    of_device_is_compatible(np, "sirf,atlas7-usp-uart"))
 		sirfport->is_atlas7 = true;
 
-	if (of_property_read_u32(pdev->dev.of_node,
-			"fifosize",
-			&port->fifosize)) {
+	if (of_property_read_u32(np, "fifosize", &port->fifosize)) {
 		dev_err(&pdev->dev,
 			"Unable to find fifosize in uart node.\n");
 		ret = -EFAULT;
diff --git a/drivers/tty/serial/uartlite.c b/drivers/tty/serial/uartlite.c
index d08baa6..05089b6 100644
--- a/drivers/tty/serial/uartlite.c
+++ b/drivers/tty/serial/uartlite.c
@@ -72,7 +72,7 @@
 	iowrite32be(val, addr);
 }
 
-static struct uartlite_reg_ops uartlite_be = {
+static const struct uartlite_reg_ops uartlite_be = {
 	.in = uartlite_inbe32,
 	.out = uartlite_outbe32,
 };
@@ -87,21 +87,21 @@
 	iowrite32(val, addr);
 }
 
-static struct uartlite_reg_ops uartlite_le = {
+static const struct uartlite_reg_ops uartlite_le = {
 	.in = uartlite_inle32,
 	.out = uartlite_outle32,
 };
 
 static inline u32 uart_in32(u32 offset, struct uart_port *port)
 {
-	struct uartlite_reg_ops *reg_ops = port->private_data;
+	const struct uartlite_reg_ops *reg_ops = port->private_data;
 
 	return reg_ops->in(port->membase + offset);
 }
 
 static inline void uart_out32(u32 val, u32 offset, struct uart_port *port)
 {
-	struct uartlite_reg_ops *reg_ops = port->private_data;
+	const struct uartlite_reg_ops *reg_ops = port->private_data;
 
 	reg_ops->out(val, port->membase + offset);
 }
@@ -345,13 +345,13 @@
 		return -EBUSY;
 	}
 
-	port->private_data = &uartlite_be;
+	port->private_data = (void *)&uartlite_be;
 	ret = uart_in32(ULITE_CONTROL, port);
 	uart_out32(ULITE_CONTROL_RST_TX, ULITE_CONTROL, port);
 	ret = uart_in32(ULITE_STATUS, port);
 	/* Endianess detection */
 	if ((ret & ULITE_STATUS_TXEMPTY) != ULITE_STATUS_TXEMPTY)
-		port->private_data = &uartlite_le;
+		port->private_data = (void *)&uartlite_le;
 
 	return 0;
 }
diff --git a/drivers/tty/serial/ucc_uart.c b/drivers/tty/serial/ucc_uart.c
index 1a7dc3c..481eb29 100644
--- a/drivers/tty/serial/ucc_uart.c
+++ b/drivers/tty/serial/ucc_uart.c
@@ -1478,6 +1478,9 @@
 		.type = "serial",
 		.compatible = "ucc_uart",
 	},
+	{
+		.compatible = "fsl,t1040-ucc-uart",
+	},
 	{},
 };
 MODULE_DEVICE_TABLE(of, ucc_uart_match);
diff --git a/drivers/tty/synclink.c b/drivers/tty/synclink.c
index c8c7601..c13e27e 100644
--- a/drivers/tty/synclink.c
+++ b/drivers/tty/synclink.c
@@ -1340,7 +1340,7 @@
 		wake_up_interruptible(&info->status_event_wait_q);
 		wake_up_interruptible(&info->event_wait_q);
 
-		if ( (info->port.flags & ASYNC_CHECK_CD) && 
+		if (tty_port_check_carrier(&info->port) &&
 		     (status & MISCSTATUS_DCD_LATCHED) ) {
 			if ( debug_level >= DEBUG_LEVEL_ISR )
 				printk("%s CD now %s...", info->device_name,
@@ -1361,8 +1361,7 @@
 				if (status & MISCSTATUS_CTS) {
 					if ( debug_level >= DEBUG_LEVEL_ISR )
 						printk("CTS tx start...");
-					if (info->port.tty)
-						info->port.tty->hw_stopped = 0;
+					info->port.tty->hw_stopped = 0;
 					usc_start_transmitter(info);
 					info->pending_bh |= BH_TRANSMIT;
 					return;
@@ -1749,13 +1748,13 @@
 static int startup(struct mgsl_struct * info)
 {
 	int retval = 0;
-	
+
 	if ( debug_level >= DEBUG_LEVEL_INFO )
 		printk("%s(%d):mgsl_startup(%s)\n",__FILE__,__LINE__,info->device_name);
-		
-	if (info->port.flags & ASYNC_INITIALIZED)
+
+	if (tty_port_initialized(&info->port))
 		return 0;
-	
+
 	if (!info->xmit_buf) {
 		/* allocate a page of memory for a transmit buffer */
 		info->xmit_buf = (unsigned char *)get_zeroed_page(GFP_KERNEL);
@@ -1788,14 +1787,13 @@
 
 	/* program hardware for current parameters */
 	mgsl_change_params(info);
-	
+
 	if (info->port.tty)
 		clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
 
-	info->port.flags |= ASYNC_INITIALIZED;
-	
+	tty_port_set_initialized(&info->port, 1);
+
 	return 0;
-	
 }	/* end of startup() */
 
 /* shutdown()
@@ -1808,8 +1806,8 @@
 static void shutdown(struct mgsl_struct * info)
 {
 	unsigned long flags;
-	
-	if (!(info->port.flags & ASYNC_INITIALIZED))
+
+	if (!tty_port_initialized(&info->port))
 		return;
 
 	if (debug_level >= DEBUG_LEVEL_INFO)
@@ -1853,13 +1851,12 @@
 
 	spin_unlock_irqrestore(&info->irq_spinlock,flags);
 
-	mgsl_release_resources(info);	
-	
+	mgsl_release_resources(info);
+
 	if (info->port.tty)
 		set_bit(TTY_IO_ERROR, &info->port.tty->flags);
 
-	info->port.flags &= ~ASYNC_INITIALIZED;
-	
+	tty_port_set_initialized(&info->port, 0);
 }	/* end of shutdown() */
 
 static void mgsl_program_hw(struct mgsl_struct *info)
@@ -1966,15 +1963,8 @@
 	}
 	info->timeout += HZ/50;		/* Add .02 seconds of slop */
 
-	if (cflag & CRTSCTS)
-		info->port.flags |= ASYNC_CTS_FLOW;
-	else
-		info->port.flags &= ~ASYNC_CTS_FLOW;
-		
-	if (cflag & CLOCAL)
-		info->port.flags &= ~ASYNC_CHECK_CD;
-	else
-		info->port.flags |= ASYNC_CHECK_CD;
+	tty_port_set_cts_flow(&info->port, cflag & CRTSCTS);
+	tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
 
 	/* process tty input control flags */
 	
@@ -2972,7 +2962,7 @@
 
 	if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
 	    (cmd != TIOCMIWAIT)) {
-		if (tty->flags & (1 << TTY_IO_ERROR))
+		if (tty_io_error(tty))
 		    return -EIO;
 	}
 
@@ -3049,7 +3039,7 @@
 	/* Handle transition away from B0 status */
 	if (!(old_termios->c_cflag & CBAUD) && C_BAUD(tty)) {
 		info->serial_signals |= SerialSignal_DTR;
-		if (!C_CRTSCTS(tty) || !test_bit(TTY_THROTTLED, &tty->flags))
+		if (!C_CRTSCTS(tty) || !tty_throttled(tty))
 			info->serial_signals |= SerialSignal_RTS;
 		spin_lock_irqsave(&info->irq_spinlock,flags);
 	 	usc_set_serial_signals(info);
@@ -3091,7 +3081,7 @@
 		goto cleanup;
 
 	mutex_lock(&info->port.mutex);
- 	if (info->port.flags & ASYNC_INITIALIZED)
+	if (tty_port_initialized(&info->port))
  		mgsl_wait_until_sent(tty, info->timeout);
 	mgsl_flush_buffer(tty);
 	tty_ldisc_flush(tty);
@@ -3129,15 +3119,15 @@
 	if (debug_level >= DEBUG_LEVEL_INFO)
 		printk("%s(%d):mgsl_wait_until_sent(%s) entry\n",
 			 __FILE__,__LINE__, info->device_name );
-      
+
 	if (mgsl_paranoia_check(info, tty->name, "mgsl_wait_until_sent"))
 		return;
 
-	if (!(info->port.flags & ASYNC_INITIALIZED))
+	if (!tty_port_initialized(&info->port))
 		goto exit;
-	 
+
 	orig_jiffies = jiffies;
-      
+
 	/* Set check interval to 1/5 of estimated time to
 	 * send a character, and make it at least 1. The check
 	 * interval should also be less than the timeout.
@@ -3204,7 +3194,7 @@
 	shutdown(info);
 	
 	info->port.count = 0;	
-	info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
+	tty_port_set_active(&info->port, 0);
 	info->port.tty = NULL;
 
 	wake_up_interruptible(&info->port.open_wait);
@@ -3270,9 +3260,9 @@
 		printk("%s(%d):block_til_ready on %s\n",
 			 __FILE__,__LINE__, tty->driver->name );
 
-	if (filp->f_flags & O_NONBLOCK || tty->flags & (1 << TTY_IO_ERROR)){
+	if (filp->f_flags & O_NONBLOCK || tty_io_error(tty)) {
 		/* nonblock mode is set or port is not enabled */
-		port->flags |= ASYNC_NORMAL_ACTIVE;
+		tty_port_set_active(port, 1);
 		return 0;
 	}
 
@@ -3297,14 +3287,14 @@
 	port->count--;
 	spin_unlock_irqrestore(&info->irq_spinlock, flags);
 	port->blocked_open++;
-	
+
 	while (1) {
-		if (C_BAUD(tty) && test_bit(ASYNCB_INITIALIZED, &port->flags))
+		if (C_BAUD(tty) && tty_port_initialized(port))
 			tty_port_raise_dtr_rts(port);
-		
+
 		set_current_state(TASK_INTERRUPTIBLE);
-		
-		if (tty_hung_up_p(filp) || !(port->flags & ASYNC_INITIALIZED)){
+
+		if (tty_hung_up_p(filp) || !tty_port_initialized(port)) {
 			retval = (port->flags & ASYNC_HUP_NOTIFY) ?
 					-EAGAIN : -ERESTARTSYS;
 			break;
@@ -3341,7 +3331,7 @@
 			 __FILE__,__LINE__, tty->driver->name, port->count );
 			 
 	if (!retval)
-		port->flags |= ASYNC_NORMAL_ACTIVE;
+		tty_port_set_active(port, 1);
 		
 	return retval;
 	
diff --git a/drivers/tty/synclink_gt.c b/drivers/tty/synclink_gt.c
index d5b6471..7aca2d4 100644
--- a/drivers/tty/synclink_gt.c
+++ b/drivers/tty/synclink_gt.c
@@ -726,7 +726,7 @@
 		goto cleanup;
 
 	mutex_lock(&info->port.mutex);
- 	if (info->port.flags & ASYNC_INITIALIZED)
+	if (tty_port_initialized(&info->port))
  		wait_until_sent(tty, info->timeout);
 	flush_buffer(tty);
 	tty_ldisc_flush(tty);
@@ -756,9 +756,9 @@
 
 	spin_lock_irqsave(&info->port.lock, flags);
 	info->port.count = 0;
-	info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
 	info->port.tty = NULL;
 	spin_unlock_irqrestore(&info->port.lock, flags);
+	tty_port_set_active(&info->port, 0);
 	mutex_unlock(&info->port.mutex);
 
 	wake_up_interruptible(&info->port.open_wait);
@@ -784,7 +784,7 @@
 	/* Handle transition away from B0 status */
 	if (!(old_termios->c_cflag & CBAUD) && C_BAUD(tty)) {
 		info->signals |= SerialSignal_DTR;
- 		if (!C_CRTSCTS(tty) || !test_bit(TTY_THROTTLED, &tty->flags))
+		if (!C_CRTSCTS(tty) || !tty_throttled(tty))
 			info->signals |= SerialSignal_RTS;
 		spin_lock_irqsave(&info->lock,flags);
 	 	set_signals(info);
@@ -893,7 +893,7 @@
 	if (sanity_check(info, tty->name, "wait_until_sent"))
 		return;
 	DBGINFO(("%s wait_until_sent entry\n", info->device_name));
-	if (!(info->port.flags & ASYNC_INITIALIZED))
+	if (!tty_port_initialized(&info->port))
 		goto exit;
 
 	orig_jiffies = jiffies;
@@ -1032,7 +1032,7 @@
 
 	if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
 	    (cmd != TIOCMIWAIT)) {
-		if (tty->flags & (1 << TTY_IO_ERROR))
+		if (tty_io_error(tty))
 		    return -EIO;
 	}
 
@@ -2080,7 +2080,7 @@
 	wake_up_interruptible(&info->event_wait_q);
 	info->pending_bh |= BH_STATUS;
 
-	if (info->port.flags & ASYNC_CHECK_CD) {
+	if (tty_port_check_carrier(&info->port)) {
 		if (info->signals & SerialSignal_DCD)
 			wake_up_interruptible(&info->port.open_wait);
 		else {
@@ -2421,7 +2421,7 @@
 {
 	DBGINFO(("%s startup\n", info->device_name));
 
-	if (info->port.flags & ASYNC_INITIALIZED)
+	if (tty_port_initialized(&info->port))
 		return 0;
 
 	if (!info->tx_buf) {
@@ -2442,7 +2442,7 @@
 	if (info->port.tty)
 		clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
 
-	info->port.flags |= ASYNC_INITIALIZED;
+	tty_port_set_initialized(&info->port, 1);
 
 	return 0;
 }
@@ -2454,7 +2454,7 @@
 {
 	unsigned long flags;
 
-	if (!(info->port.flags & ASYNC_INITIALIZED))
+	if (!tty_port_initialized(&info->port))
 		return;
 
 	DBGINFO(("%s shutdown\n", info->device_name));
@@ -2489,7 +2489,7 @@
 	if (info->port.tty)
 		set_bit(TTY_IO_ERROR, &info->port.tty->flags);
 
-	info->port.flags &= ~ASYNC_INITIALIZED;
+	tty_port_set_initialized(&info->port, 0);
 }
 
 static void program_hw(struct slgt_info *info)
@@ -2576,15 +2576,8 @@
 	}
 	info->timeout += HZ/50;		/* Add .02 seconds of slop */
 
-	if (cflag & CRTSCTS)
-		info->port.flags |= ASYNC_CTS_FLOW;
-	else
-		info->port.flags &= ~ASYNC_CTS_FLOW;
-
-	if (cflag & CLOCAL)
-		info->port.flags &= ~ASYNC_CHECK_CD;
-	else
-		info->port.flags |= ASYNC_CHECK_CD;
+	tty_port_set_cts_flow(&info->port, cflag & CRTSCTS);
+	tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
 
 	/* process tty input control flags */
 
@@ -3269,9 +3262,9 @@
 
 	DBGINFO(("%s block_til_ready\n", tty->driver->name));
 
-	if (filp->f_flags & O_NONBLOCK || tty->flags & (1 << TTY_IO_ERROR)){
+	if (filp->f_flags & O_NONBLOCK || tty_io_error(tty)) {
 		/* nonblock mode is set or port is not enabled */
-		port->flags |= ASYNC_NORMAL_ACTIVE;
+		tty_port_set_active(port, 1);
 		return 0;
 	}
 
@@ -3294,12 +3287,12 @@
 	port->blocked_open++;
 
 	while (1) {
-		if (C_BAUD(tty) && test_bit(ASYNCB_INITIALIZED, &port->flags))
+		if (C_BAUD(tty) && tty_port_initialized(port))
 			tty_port_raise_dtr_rts(port);
 
 		set_current_state(TASK_INTERRUPTIBLE);
 
-		if (tty_hung_up_p(filp) || !(port->flags & ASYNC_INITIALIZED)){
+		if (tty_hung_up_p(filp) || !tty_port_initialized(port)) {
 			retval = (port->flags & ASYNC_HUP_NOTIFY) ?
 					-EAGAIN : -ERESTARTSYS;
 			break;
@@ -3328,7 +3321,7 @@
 	port->blocked_open--;
 
 	if (!retval)
-		port->flags |= ASYNC_NORMAL_ACTIVE;
+		tty_port_set_active(port, 1);
 
 	DBGINFO(("%s block_til_ready ready, rc=%d\n", tty->driver->name, retval));
 	return retval;
diff --git a/drivers/tty/synclinkmp.c b/drivers/tty/synclinkmp.c
index 3f89685..dec1565 100644
--- a/drivers/tty/synclinkmp.c
+++ b/drivers/tty/synclinkmp.c
@@ -812,7 +812,7 @@
 		goto cleanup;
 
 	mutex_lock(&info->port.mutex);
- 	if (info->port.flags & ASYNC_INITIALIZED)
+	if (tty_port_initialized(&info->port))
  		wait_until_sent(tty, info->timeout);
 
 	flush_buffer(tty);
@@ -849,9 +849,9 @@
 
 	spin_lock_irqsave(&info->port.lock, flags);
 	info->port.count = 0;
-	info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
 	info->port.tty = NULL;
 	spin_unlock_irqrestore(&info->port.lock, flags);
+	tty_port_set_active(&info->port, 1);
 	mutex_unlock(&info->port.mutex);
 
 	wake_up_interruptible(&info->port.open_wait);
@@ -881,7 +881,7 @@
 	/* Handle transition away from B0 status */
 	if (!(old_termios->c_cflag & CBAUD) && C_BAUD(tty)) {
 		info->serial_signals |= SerialSignal_DTR;
- 		if (!C_CRTSCTS(tty) || !test_bit(TTY_THROTTLED, &tty->flags))
+		if (!C_CRTSCTS(tty) || !tty_throttled(tty))
 			info->serial_signals |= SerialSignal_RTS;
 		spin_lock_irqsave(&info->lock,flags);
 	 	set_signals(info);
@@ -1061,7 +1061,7 @@
 	if (sanity_check(info, tty->name, "wait_until_sent"))
 		return;
 
-	if (!test_bit(ASYNCB_INITIALIZED, &info->port.flags))
+	if (!tty_port_initialized(&info->port))
 		goto exit;
 
 	orig_jiffies = jiffies;
@@ -1261,7 +1261,7 @@
 
 	if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
 	    (cmd != TIOCMIWAIT)) {
-		if (tty->flags & (1 << TTY_IO_ERROR))
+		if (tty_io_error(tty))
 		    return -EIO;
 	}
 
@@ -2463,7 +2463,7 @@
 		wake_up_interruptible(&info->status_event_wait_q);
 		wake_up_interruptible(&info->event_wait_q);
 
-		if ( (info->port.flags & ASYNC_CHECK_CD) &&
+		if (tty_port_check_carrier(&info->port) &&
 		     (status & MISCSTATUS_DCD_LATCHED) ) {
 			if ( debug_level >= DEBUG_LEVEL_ISR )
 				printk("%s CD now %s...", info->device_name,
@@ -2636,7 +2636,7 @@
 	if ( debug_level >= DEBUG_LEVEL_INFO )
 		printk("%s(%d):%s tx_releaseup()\n",__FILE__,__LINE__,info->device_name);
 
-	if (info->port.flags & ASYNC_INITIALIZED)
+	if (tty_port_initialized(&info->port))
 		return 0;
 
 	if (!info->tx_buf) {
@@ -2662,7 +2662,7 @@
 	if (info->port.tty)
 		clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
 
-	info->port.flags |= ASYNC_INITIALIZED;
+	tty_port_set_initialized(&info->port, 1);
 
 	return 0;
 }
@@ -2673,7 +2673,7 @@
 {
 	unsigned long flags;
 
-	if (!(info->port.flags & ASYNC_INITIALIZED))
+	if (!tty_port_initialized(&info->port))
 		return;
 
 	if (debug_level >= DEBUG_LEVEL_INFO)
@@ -2705,7 +2705,7 @@
 	if (info->port.tty)
 		set_bit(TTY_IO_ERROR, &info->port.tty->flags);
 
-	info->port.flags &= ~ASYNC_INITIALIZED;
+	tty_port_set_initialized(&info->port, 0);
 }
 
 static void program_hw(SLMP_INFO *info)
@@ -2813,15 +2813,8 @@
 	}
 	info->timeout += HZ/50;		/* Add .02 seconds of slop */
 
-	if (cflag & CRTSCTS)
-		info->port.flags |= ASYNC_CTS_FLOW;
-	else
-		info->port.flags &= ~ASYNC_CTS_FLOW;
-
-	if (cflag & CLOCAL)
-		info->port.flags &= ~ASYNC_CHECK_CD;
-	else
-		info->port.flags |= ASYNC_CHECK_CD;
+	tty_port_set_cts_flow(&info->port, cflag & CRTSCTS);
+	tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
 
 	/* process tty input control flags */
 
@@ -3285,10 +3278,10 @@
 		printk("%s(%d):%s block_til_ready()\n",
 			 __FILE__,__LINE__, tty->driver->name );
 
-	if (filp->f_flags & O_NONBLOCK || tty->flags & (1 << TTY_IO_ERROR)){
+	if (filp->f_flags & O_NONBLOCK || tty_io_error(tty)) {
 		/* nonblock mode is set or port is not enabled */
 		/* just verify that callout device is not active */
-		port->flags |= ASYNC_NORMAL_ACTIVE;
+		tty_port_set_active(port, 1);
 		return 0;
 	}
 
@@ -3315,12 +3308,12 @@
 	port->blocked_open++;
 
 	while (1) {
-		if (C_BAUD(tty) && test_bit(ASYNCB_INITIALIZED, &port->flags))
+		if (C_BAUD(tty) && tty_port_initialized(port))
 			tty_port_raise_dtr_rts(port);
 
 		set_current_state(TASK_INTERRUPTIBLE);
 
-		if (tty_hung_up_p(filp) || !(port->flags & ASYNC_INITIALIZED)){
+		if (tty_hung_up_p(filp) || !tty_port_initialized(port)) {
 			retval = (port->flags & ASYNC_HUP_NOTIFY) ?
 					-EAGAIN : -ERESTARTSYS;
 			break;
@@ -3355,7 +3348,7 @@
 			 __FILE__,__LINE__, tty->driver->name, port->count );
 
 	if (!retval)
-		port->flags |= ASYNC_NORMAL_ACTIVE;
+		tty_port_set_active(port, 1);
 
 	return retval;
 }
diff --git a/drivers/tty/tty_buffer.c b/drivers/tty/tty_buffer.c
index a946e49..aa80dc9 100644
--- a/drivers/tty/tty_buffer.c
+++ b/drivers/tty/tty_buffer.c
@@ -37,29 +37,6 @@
 
 #define TTY_BUFFER_PAGE	(((PAGE_SIZE - sizeof(struct tty_buffer)) / 2) & ~0xFF)
 
-/*
- * If all tty flip buffers have been processed by flush_to_ldisc() or
- * dropped by tty_buffer_flush(), check if the linked pty has been closed.
- * If so, wake the reader/poll to process
- */
-static inline void check_other_closed(struct tty_struct *tty)
-{
-	unsigned long flags, old;
-
-	/* transition from TTY_OTHER_CLOSED => TTY_OTHER_DONE must be atomic */
-	for (flags = ACCESS_ONCE(tty->flags);
-	     test_bit(TTY_OTHER_CLOSED, &flags);
-	     ) {
-		old = flags;
-		__set_bit(TTY_OTHER_DONE, &flags);
-		flags = cmpxchg(&tty->flags, old, flags);
-		if (old == flags) {
-			wake_up_interruptible(&tty->read_wait);
-			break;
-		}
-	}
-}
-
 /**
  *	tty_buffer_lock_exclusive	-	gain exclusive access to buffer
  *	tty_buffer_unlock_exclusive	-	release exclusive access
@@ -254,8 +231,6 @@
 	if (ld && ld->ops->flush_buffer)
 		ld->ops->flush_buffer(tty);
 
-	check_other_closed(tty);
-
 	atomic_dec(&buf->priority);
 	mutex_unlock(&buf->lock);
 }
@@ -522,10 +497,8 @@
 		 */
 		count = smp_load_acquire(&head->commit) - head->read;
 		if (!count) {
-			if (next == NULL) {
-				check_other_closed(tty);
+			if (next == NULL)
 				break;
-			}
 			buf->head = next;
 			tty_buffer_free(port, head);
 			continue;
@@ -614,3 +587,8 @@
 {
 	return cancel_work_sync(&port->buf.work);
 }
+
+void tty_buffer_flush_work(struct tty_port *port)
+{
+	flush_work(&port->buf.work);
+}
diff --git a/drivers/tty/tty_io.c b/drivers/tty/tty_io.c
index 24d5491..734a635 100644
--- a/drivers/tty/tty_io.c
+++ b/drivers/tty/tty_io.c
@@ -230,9 +230,6 @@
 	tty_free_file(file);
 }
 
-
-#define TTY_NUMBER(tty) ((tty)->index + (tty)->driver->name_base)
-
 /**
  *	tty_name	-	return tty naming
  *	@tty: tty structure
@@ -1070,7 +1067,7 @@
 
 	if (tty_paranoia_check(tty, inode, "tty_read"))
 		return -EIO;
-	if (!tty || (test_bit(TTY_IO_ERROR, &tty->flags)))
+	if (!tty || tty_io_error(tty))
 		return -EIO;
 
 	/* We want to wait for the line discipline to sort out in this
@@ -1245,8 +1242,7 @@
 
 	if (tty_paranoia_check(tty, file_inode(file), "tty_write"))
 		return -EIO;
-	if (!tty || !tty->ops->write ||
-		(test_bit(TTY_IO_ERROR, &tty->flags)))
+	if (!tty || !tty->ops->write ||	tty_io_error(tty))
 			return -EIO;
 	/* Short term debug to catch buggy drivers */
 	if (tty->ops->write_room == NULL)
@@ -1964,7 +1960,6 @@
  *	tty_lookup_driver - lookup a tty driver for a given device file
  *	@device: device number
  *	@filp: file pointer to tty
- *	@noctty: set if the device should not become a controlling tty
  *	@index: index for the device in the @return driver
  *	@return: driver for this inode (with increased refcount)
  *
diff --git a/drivers/tty/tty_ioctl.c b/drivers/tty/tty_ioctl.c
index 23bf5bb..bf36ac9 100644
--- a/drivers/tty/tty_ioctl.c
+++ b/drivers/tty/tty_ioctl.c
@@ -158,7 +158,7 @@
 	int ret = 0;
 
 	mutex_lock(&tty->throttle_mutex);
-	if (!test_bit(TTY_THROTTLED, &tty->flags)) {
+	if (!tty_throttled(tty)) {
 		if (tty->flow_change != TTY_THROTTLE_SAFE)
 			ret = 1;
 		else {
@@ -189,7 +189,7 @@
 	int ret = 0;
 
 	mutex_lock(&tty->throttle_mutex);
-	if (test_bit(TTY_THROTTLED, &tty->flags)) {
+	if (tty_throttled(tty)) {
 		if (tty->flow_change != TTY_UNTHROTTLE_SAFE)
 			ret = 1;
 		else {
diff --git a/drivers/tty/tty_port.c b/drivers/tty/tty_port.c
index dbcca30..c3f9d93 100644
--- a/drivers/tty/tty_port.c
+++ b/drivers/tty/tty_port.c
@@ -204,7 +204,8 @@
 	if (port->console)
 		goto out;
 
-	if (test_and_clear_bit(ASYNCB_INITIALIZED, &port->flags)) {
+	if (tty_port_initialized(port)) {
+		tty_port_set_initialized(port, 0);
 		/*
 		 * Drop DTR/RTS if HUPCL is set. This causes any attached
 		 * modem to hang up the line.
@@ -236,12 +237,12 @@
 
 	spin_lock_irqsave(&port->lock, flags);
 	port->count = 0;
-	port->flags &= ~ASYNC_NORMAL_ACTIVE;
 	tty = port->tty;
 	if (tty)
 		set_bit(TTY_IO_ERROR, &tty->flags);
 	port->tty = NULL;
 	spin_unlock_irqrestore(&port->lock, flags);
+	tty_port_set_active(port, 0);
 	tty_port_shutdown(port, tty);
 	tty_kref_put(tty);
 	wake_up_interruptible(&port->open_wait);
@@ -364,15 +365,15 @@
 
 	/* if non-blocking mode is set we can pass directly to open unless
 	   the port has just hung up or is in another error state */
-	if (tty->flags & (1 << TTY_IO_ERROR)) {
-		port->flags |= ASYNC_NORMAL_ACTIVE;
+	if (tty_io_error(tty)) {
+		tty_port_set_active(port, 1);
 		return 0;
 	}
 	if (filp->f_flags & O_NONBLOCK) {
 		/* Indicate we are open */
 		if (C_BAUD(tty))
 			tty_port_raise_dtr_rts(port);
-		port->flags |= ASYNC_NORMAL_ACTIVE;
+		tty_port_set_active(port, 1);
 		return 0;
 	}
 
@@ -393,13 +394,13 @@
 
 	while (1) {
 		/* Indicate we are open */
-		if (C_BAUD(tty) && test_bit(ASYNCB_INITIALIZED, &port->flags))
+		if (C_BAUD(tty) && tty_port_initialized(port))
 			tty_port_raise_dtr_rts(port);
 
 		prepare_to_wait(&port->open_wait, &wait, TASK_INTERRUPTIBLE);
 		/* Check for a hangup or uninitialised port.
 							Return accordingly */
-		if (tty_hung_up_p(filp) || !(port->flags & ASYNC_INITIALIZED)) {
+		if (tty_hung_up_p(filp) || !tty_port_initialized(port)) {
 			if (port->flags & ASYNC_HUP_NOTIFY)
 				retval = -EAGAIN;
 			else
@@ -430,9 +431,9 @@
 	if (!tty_hung_up_p(filp))
 		port->count++;
 	port->blocked_open--;
-	if (retval == 0)
-		port->flags |= ASYNC_NORMAL_ACTIVE;
 	spin_unlock_irqrestore(&port->lock, flags);
+	if (retval == 0)
+		tty_port_set_active(port, 1);
 	return retval;
 }
 EXPORT_SYMBOL(tty_port_block_til_ready);
@@ -480,7 +481,7 @@
 
 	tty->closing = 1;
 
-	if (test_bit(ASYNCB_INITIALIZED, &port->flags)) {
+	if (tty_port_initialized(port)) {
 		/* Don't block on a stalled port, just pull the chain */
 		if (tty->flow_stopped)
 			tty_driver_flush_buffer(tty);
@@ -514,8 +515,8 @@
 		spin_lock_irqsave(&port->lock, flags);
 		wake_up_interruptible(&port->open_wait);
 	}
-	port->flags &= ~ASYNC_NORMAL_ACTIVE;
 	spin_unlock_irqrestore(&port->lock, flags);
+	tty_port_set_active(port, 0);
 }
 EXPORT_SYMBOL(tty_port_close_end);
 
@@ -578,7 +579,7 @@
 
 	mutex_lock(&port->mutex);
 
-	if (!test_bit(ASYNCB_INITIALIZED, &port->flags)) {
+	if (!tty_port_initialized(port)) {
 		clear_bit(TTY_IO_ERROR, &tty->flags);
 		if (port->ops->activate) {
 			int retval = port->ops->activate(port, tty);
@@ -587,7 +588,7 @@
 				return retval;
 			}
 		}
-		set_bit(ASYNCB_INITIALIZED, &port->flags);
+		tty_port_set_initialized(port, 1);
 	}
 	mutex_unlock(&port->mutex);
 	return tty_port_block_til_ready(port, tty, filp);
diff --git a/drivers/tty/vt/selection.c b/drivers/tty/vt/selection.c
index 4dd9dd2..368ce18 100644
--- a/drivers/tty/vt/selection.c
+++ b/drivers/tty/vt/selection.c
@@ -354,7 +354,7 @@
 	add_wait_queue(&vc->paste_wait, &wait);
 	while (sel_buffer && sel_buffer_lth > pasted) {
 		set_current_state(TASK_INTERRUPTIBLE);
-		if (test_bit(TTY_THROTTLED, &tty->flags)) {
+		if (tty_throttled(tty)) {
 			schedule();
 			continue;
 		}
diff --git a/drivers/tty/vt/vt.c b/drivers/tty/vt/vt.c
index 3e3c757..dc12532 100644
--- a/drivers/tty/vt/vt.c
+++ b/drivers/tty/vt/vt.c
@@ -760,50 +760,54 @@
 
 int vc_allocate(unsigned int currcons)	/* return 0 on success */
 {
+	struct vt_notifier_param param;
+	struct vc_data *vc;
+
 	WARN_CONSOLE_UNLOCKED();
 
 	if (currcons >= MAX_NR_CONSOLES)
 		return -ENXIO;
-	if (!vc_cons[currcons].d) {
-	    struct vc_data *vc;
-	    struct vt_notifier_param param;
 
-	    /* prevent users from taking too much memory */
-	    if (currcons >= MAX_NR_USER_CONSOLES && !capable(CAP_SYS_RESOURCE))
-	      return -EPERM;
+	if (vc_cons[currcons].d)
+		return 0;
 
-	    /* due to the granularity of kmalloc, we waste some memory here */
-	    /* the alloc is done in two steps, to optimize the common situation
-	       of a 25x80 console (structsize=216, screenbuf_size=4000) */
-	    /* although the numbers above are not valid since long ago, the
-	       point is still up-to-date and the comment still has its value
-	       even if only as a historical artifact.  --mj, July 1998 */
-	    param.vc = vc = kzalloc(sizeof(struct vc_data), GFP_KERNEL);
-	    if (!vc)
+	/* due to the granularity of kmalloc, we waste some memory here */
+	/* the alloc is done in two steps, to optimize the common situation
+	   of a 25x80 console (structsize=216, screenbuf_size=4000) */
+	/* although the numbers above are not valid since long ago, the
+	   point is still up-to-date and the comment still has its value
+	   even if only as a historical artifact.  --mj, July 1998 */
+	param.vc = vc = kzalloc(sizeof(struct vc_data), GFP_KERNEL);
+	if (!vc)
 		return -ENOMEM;
-	    vc_cons[currcons].d = vc;
-	    tty_port_init(&vc->port);
-	    INIT_WORK(&vc_cons[currcons].SAK_work, vc_SAK);
-	    visual_init(vc, currcons, 1);
-	    if (!*vc->vc_uni_pagedir_loc)
+
+	vc_cons[currcons].d = vc;
+	tty_port_init(&vc->port);
+	INIT_WORK(&vc_cons[currcons].SAK_work, vc_SAK);
+
+	visual_init(vc, currcons, 1);
+
+	if (!*vc->vc_uni_pagedir_loc)
 		con_set_default_unimap(vc);
-	    vc->vc_screenbuf = kmalloc(vc->vc_screenbuf_size, GFP_KERNEL);
-	    if (!vc->vc_screenbuf) {
-		kfree(vc);
-		vc_cons[currcons].d = NULL;
-		return -ENOMEM;
-	    }
 
-	    /* If no drivers have overridden us and the user didn't pass a
-	       boot option, default to displaying the cursor */
-	    if (global_cursor_default == -1)
-		    global_cursor_default = 1;
+	vc->vc_screenbuf = kmalloc(vc->vc_screenbuf_size, GFP_KERNEL);
+	if (!vc->vc_screenbuf)
+		goto err_free;
 
-	    vc_init(vc, vc->vc_rows, vc->vc_cols, 1);
-	    vcs_make_sysfs(currcons);
-	    atomic_notifier_call_chain(&vt_notifier_list, VT_ALLOCATE, &param);
-	}
+	/* If no drivers have overridden us and the user didn't pass a
+	   boot option, default to displaying the cursor */
+	if (global_cursor_default == -1)
+		global_cursor_default = 1;
+
+	vc_init(vc, vc->vc_rows, vc->vc_cols, 1);
+	vcs_make_sysfs(currcons);
+	atomic_notifier_call_chain(&vt_notifier_list, VT_ALLOCATE, &param);
+
 	return 0;
+err_free:
+	kfree(vc);
+	vc_cons[currcons].d = NULL;
+	return -ENOMEM;
 }
 
 static inline int resize_screen(struct vc_data *vc, int width, int height,
@@ -1035,20 +1039,27 @@
 #define VT100ID "\033[?1;2c"
 #define VT102ID "\033[?6c"
 
-unsigned char color_table[] = { 0, 4, 2, 6, 1, 5, 3, 7,
+const unsigned char color_table[] = { 0, 4, 2, 6, 1, 5, 3, 7,
 				       8,12,10,14, 9,13,11,15 };
 
 /* the default colour table, for VGA+ colour systems */
-int default_red[] = {0x00,0xaa,0x00,0xaa,0x00,0xaa,0x00,0xaa,
-    0x55,0xff,0x55,0xff,0x55,0xff,0x55,0xff};
-int default_grn[] = {0x00,0x00,0xaa,0x55,0x00,0x00,0xaa,0xaa,
-    0x55,0x55,0xff,0xff,0x55,0x55,0xff,0xff};
-int default_blu[] = {0x00,0x00,0x00,0x00,0xaa,0xaa,0xaa,0xaa,
-    0x55,0x55,0x55,0x55,0xff,0xff,0xff,0xff};
+unsigned char default_red[] = {
+	0x00, 0xaa, 0x00, 0xaa, 0x00, 0xaa, 0x00, 0xaa,
+	0x55, 0xff, 0x55, 0xff, 0x55, 0xff, 0x55, 0xff
+};
+module_param_array(default_red, byte, NULL, S_IRUGO | S_IWUSR);
 
-module_param_array(default_red, int, NULL, S_IRUGO | S_IWUSR);
-module_param_array(default_grn, int, NULL, S_IRUGO | S_IWUSR);
-module_param_array(default_blu, int, NULL, S_IRUGO | S_IWUSR);
+unsigned char default_grn[] = {
+	0x00, 0x00, 0xaa, 0x55, 0x00, 0x00, 0xaa, 0xaa,
+	0x55, 0x55, 0xff, 0xff, 0x55, 0x55, 0xff, 0xff
+};
+module_param_array(default_grn, byte, NULL, S_IRUGO | S_IWUSR);
+
+unsigned char default_blu[] = {
+	0x00, 0x00, 0x00, 0x00, 0xaa, 0xaa, 0xaa, 0xaa,
+	0x55, 0x55, 0x55, 0x55, 0xff, 0xff, 0xff, 0xff
+};
+module_param_array(default_blu, byte, NULL, S_IRUGO | S_IWUSR);
 
 /*
  * gotoxy() must verify all boundaries, because the arguments
@@ -3564,7 +3575,7 @@
 	struct module *owner = csw->owner;
 	struct con_driver *con_driver;
 	const char *desc;
-	int i, retval = 0;
+	int i, retval;
 
 	WARN_CONSOLE_UNLOCKED();
 
@@ -3575,17 +3586,17 @@
 		con_driver = &registered_con_driver[i];
 
 		/* already registered */
-		if (con_driver->con == csw)
+		if (con_driver->con == csw) {
 			retval = -EBUSY;
+			goto err;
+		}
 	}
 
-	if (retval)
-		goto err;
-
 	desc = csw->con_startup();
-
-	if (!desc)
+	if (!desc) {
+		retval = -ENODEV;
 		goto err;
+	}
 
 	retval = -EINVAL;
 
diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c
index a6c4a1b..94a14f5 100644
--- a/drivers/usb/class/cdc-acm.c
+++ b/drivers/usb/class/cdc-acm.c
@@ -1680,7 +1680,7 @@
 	if (--acm->susp_count)
 		goto out;
 
-	if (test_bit(ASYNCB_INITIALIZED, &acm->port.flags)) {
+	if (tty_port_initialized(&acm->port)) {
 		rv = usb_submit_urb(acm->ctrlurb, GFP_ATOMIC);
 
 		for (;;) {
@@ -1710,7 +1710,7 @@
 {
 	struct acm *acm = usb_get_intfdata(intf);
 
-	if (test_bit(ASYNCB_INITIALIZED, &acm->port.flags))
+	if (tty_port_initialized(&acm->port))
 		tty_port_tty_hangup(&acm->port, false);
 
 	return acm_resume(intf);
diff --git a/drivers/usb/gadget/function/u_serial.c b/drivers/usb/gadget/function/u_serial.c
index 6af145f..3580f19 100644
--- a/drivers/usb/gadget/function/u_serial.c
+++ b/drivers/usb/gadget/function/u_serial.c
@@ -512,7 +512,7 @@
 		req = list_first_entry(queue, struct usb_request, list);
 
 		/* leave data queued if tty was rx throttled */
-		if (tty && test_bit(TTY_THROTTLED, &tty->flags))
+		if (tty && tty_throttled(tty))
 			break;
 
 		switch (req->status) {
@@ -579,7 +579,7 @@
 	 * from starving ... but it's not clear that case ever happens.
 	 */
 	if (!list_empty(queue) && tty) {
-		if (!test_bit(TTY_THROTTLED, &tty->flags)) {
+		if (!tty_throttled(tty)) {
 			if (do_push)
 				tasklet_schedule(&port->push);
 			else
diff --git a/drivers/usb/misc/sisusbvga/sisusb_con.c b/drivers/usb/misc/sisusbvga/sisusb_con.c
index ace3430..afa8532 100644
--- a/drivers/usb/misc/sisusbvga/sisusb_con.c
+++ b/drivers/usb/misc/sisusbvga/sisusb_con.c
@@ -601,7 +601,7 @@
 
 /* interface routine */
 static int
-sisusbcon_set_palette(struct vc_data *c, unsigned char *table)
+sisusbcon_set_palette(struct vc_data *c, const unsigned char *table)
 {
 	struct sisusb_usb_data *sisusb;
 	int i, j;
diff --git a/drivers/usb/serial/console.c b/drivers/usb/serial/console.c
index a66b01b..8967715 100644
--- a/drivers/usb/serial/console.c
+++ b/drivers/usb/serial/console.c
@@ -127,7 +127,7 @@
 	info->port = port;
 
 	++port->port.count;
-	if (!test_bit(ASYNCB_INITIALIZED, &port->port.flags)) {
+	if (!tty_port_initialized(&port->port)) {
 		if (serial->type->set_termios) {
 			/*
 			 * allocate a fake tty so the driver can initialize
@@ -168,7 +168,7 @@
 			tty_port_tty_set(&port->port, NULL);
 			tty_kref_put(tty);
 		}
-		set_bit(ASYNCB_INITIALIZED, &port->port.flags);
+		tty_port_set_initialized(&port->port, 1);
 	}
 	/* Now that any required fake tty operations are completed restore
 	 * the tty port count */
diff --git a/drivers/usb/serial/digi_acceleport.c b/drivers/usb/serial/digi_acceleport.c
index 16e8e37..6a1df9e 100644
--- a/drivers/usb/serial/digi_acceleport.c
+++ b/drivers/usb/serial/digi_acceleport.c
@@ -699,8 +699,7 @@
 			/* don't set RTS if using hardware flow control */
 			/* and throttling input */
 			modem_signals = TIOCM_DTR;
-			if (!C_CRTSCTS(tty) ||
-			    !test_bit(TTY_THROTTLED, &tty->flags))
+			if (!C_CRTSCTS(tty) || !tty_throttled(tty))
 				modem_signals |= TIOCM_RTS;
 			digi_set_modem_signals(port, modem_signals, 1);
 		}
diff --git a/drivers/usb/serial/generic.c b/drivers/usb/serial/generic.c
index 54e170d..ae8c036 100644
--- a/drivers/usb/serial/generic.c
+++ b/drivers/usb/serial/generic.c
@@ -473,7 +473,7 @@
 	 * Use tty-port initialised flag to detect all hangups including the
 	 * one generated at USB-device disconnect.
 	 */
-	if (!test_bit(ASYNCB_INITIALIZED, &port->port.flags))
+	if (!tty_port_initialized(&port->port))
 		return true;
 
 	spin_lock_irqsave(&port->lock, flags);
@@ -503,7 +503,7 @@
 
 	ret = wait_event_interruptible(port->port.delta_msr_wait,
 			usb_serial_generic_msr_changed(tty, arg, &cnow));
-	if (!ret && !test_bit(ASYNCB_INITIALIZED, &port->port.flags))
+	if (!ret && !tty_port_initialized(&port->port))
 		ret = -EIO;
 
 	return ret;
@@ -606,7 +606,7 @@
 
 	for (i = 0; i < serial->num_ports; i++) {
 		port = serial->port[i];
-		if (!test_bit(ASYNCB_INITIALIZED, &port->port.flags))
+		if (!tty_port_initialized(&port->port))
 			continue;
 
 		if (port->bulk_in_size) {
diff --git a/drivers/usb/serial/mxuport.c b/drivers/usb/serial/mxuport.c
index 31a8b47..3722d6c 100644
--- a/drivers/usb/serial/mxuport.c
+++ b/drivers/usb/serial/mxuport.c
@@ -503,7 +503,7 @@
 			return;
 		}
 
-		if (test_bit(ASYNCB_INITIALIZED, &demux_port->port.flags)) {
+		if (tty_port_initialized(&demux_port->port)) {
 			ch = data + HEADER_SIZE;
 			mxuport_process_read_urb_data(demux_port, ch, rcv_len);
 		} else {
@@ -544,7 +544,7 @@
 		}
 
 		demux_port = serial->port[rcv_port];
-		if (test_bit(ASYNCB_INITIALIZED, &demux_port->port.flags)) {
+		if (tty_port_initialized(&demux_port->port)) {
 			ch = data + HEADER_SIZE;
 			rcv_event = get_unaligned_be16(data + 2);
 			mxuport_process_read_urb_event(demux_port, ch,
@@ -1339,7 +1339,7 @@
 
 	for (i = 0; i < serial->num_ports; i++) {
 		port = serial->port[i];
-		if (!test_bit(ASYNCB_INITIALIZED, &port->port.flags))
+		if (!tty_port_initialized(&port->port))
 			continue;
 
 		r = usb_serial_generic_write_start(port, GFP_NOIO);
diff --git a/drivers/usb/serial/sierra.c b/drivers/usb/serial/sierra.c
index 07d1ecd..e1994e2 100644
--- a/drivers/usb/serial/sierra.c
+++ b/drivers/usb/serial/sierra.c
@@ -776,7 +776,7 @@
 
 	/*
 	 * Need to take susp_lock to make sure port is not already being
-	 * resumed, but no need to hold it due to ASYNC_INITIALIZED.
+	 * resumed, but no need to hold it due to initialized
 	 */
 	spin_lock_irq(&intfdata->susp_lock);
 	if (--intfdata->open_ports == 0)
@@ -1039,7 +1039,7 @@
 	for (i = 0; i < serial->num_ports; i++) {
 		port = serial->port[i];
 
-		if (!test_bit(ASYNCB_INITIALIZED, &port->port.flags))
+		if (!tty_port_initialized(&port->port))
 			continue;
 
 		err = sierra_submit_delayed_urbs(port);
diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c
index 46f1f13..3f253ae 100644
--- a/drivers/usb/serial/usb-serial.c
+++ b/drivers/usb/serial/usb-serial.c
@@ -254,7 +254,7 @@
  *
  * Shut down a USB serial port. Serialized against activate by the
  * tport mutex and kept to matching open/close pairs
- * of calls by the ASYNCB_INITIALIZED flag.
+ * of calls by the initialized flag.
  *
  * Not called if tty is console.
  */
diff --git a/drivers/usb/serial/usb_wwan.c b/drivers/usb/serial/usb_wwan.c
index be9cb61..3dfdfc8 100644
--- a/drivers/usb/serial/usb_wwan.c
+++ b/drivers/usb/serial/usb_wwan.c
@@ -464,7 +464,7 @@
 
 	/*
 	 * Need to take susp_lock to make sure port is not already being
-	 * resumed, but no need to hold it due to ASYNC_INITIALIZED.
+	 * resumed, but no need to hold it due to initialized
 	 */
 	spin_lock_irq(&intfdata->susp_lock);
 	if (--intfdata->open_ports == 0)
@@ -682,7 +682,7 @@
 	for (i = 0; i < serial->num_ports; i++) {
 		port = serial->port[i];
 
-		if (!test_bit(ASYNCB_INITIALIZED, &port->port.flags))
+		if (!tty_port_initialized(&port->port))
 			continue;
 
 		portdata = usb_get_serial_port_data(port);
diff --git a/drivers/video/console/fbcon.c b/drivers/video/console/fbcon.c
index 6e92917..afd3301 100644
--- a/drivers/video/console/fbcon.c
+++ b/drivers/video/console/fbcon.c
@@ -170,7 +170,7 @@
 			int height, int width);
 static int fbcon_switch(struct vc_data *vc);
 static int fbcon_blank(struct vc_data *vc, int blank, int mode_switch);
-static int fbcon_set_palette(struct vc_data *vc, unsigned char *table);
+static int fbcon_set_palette(struct vc_data *vc, const unsigned char *table);
 static int fbcon_scrolldelta(struct vc_data *vc, int lines);
 
 /*
@@ -2652,7 +2652,7 @@
 	0, 16, palette_red, palette_green, palette_blue, NULL
 };
 
-static int fbcon_set_palette(struct vc_data *vc, unsigned char *table)
+static int fbcon_set_palette(struct vc_data *vc, const unsigned char *table)
 {
 	struct fb_info *info = registered_fb[con2fb_map[vc->vc_num]];
 	int i, j, k, depth;
diff --git a/drivers/video/console/mdacon.c b/drivers/video/console/mdacon.c
index 296e945..8edc062 100644
--- a/drivers/video/console/mdacon.c
+++ b/drivers/video/console/mdacon.c
@@ -481,7 +481,7 @@
 	return 1;	/* redrawing needed */
 }
 
-static int mdacon_set_palette(struct vc_data *c, unsigned char *table)
+static int mdacon_set_palette(struct vc_data *c, const unsigned char *table)
 {
 	return -EINVAL;
 }
diff --git a/drivers/video/console/newport_con.c b/drivers/video/console/newport_con.c
index bb4e962..0553dfe 100644
--- a/drivers/video/console/newport_con.c
+++ b/drivers/video/console/newport_con.c
@@ -574,7 +574,7 @@
 	return newport_set_font(vc->vc_num, font);
 }
 
-static int newport_set_palette(struct vc_data *vc, unsigned char *table)
+static int newport_set_palette(struct vc_data *vc, const unsigned char *table)
 {
 	return -EINVAL;
 }
diff --git a/drivers/video/console/sticon.c b/drivers/video/console/sticon.c
index 026fd12..e440c2d 100644
--- a/drivers/video/console/sticon.c
+++ b/drivers/video/console/sticon.c
@@ -79,7 +79,7 @@
     return "STI console";
 }
 
-static int sticon_set_palette(struct vc_data *c, unsigned char *table)
+static int sticon_set_palette(struct vc_data *c, const unsigned char *table)
 {
     return -EINVAL;
 }
diff --git a/drivers/video/console/vgacon.c b/drivers/video/console/vgacon.c
index 517f565..8bf9110 100644
--- a/drivers/video/console/vgacon.c
+++ b/drivers/video/console/vgacon.c
@@ -80,7 +80,6 @@
 static void vgacon_cursor(struct vc_data *c, int mode);
 static int vgacon_switch(struct vc_data *c);
 static int vgacon_blank(struct vc_data *c, int blank, int mode_switch);
-static int vgacon_set_palette(struct vc_data *vc, unsigned char *table);
 static int vgacon_scrolldelta(struct vc_data *c, int lines);
 static int vgacon_set_origin(struct vc_data *c);
 static void vgacon_save_screen(struct vc_data *c);
@@ -847,7 +846,7 @@
 	return 0;		/* Redrawing not needed */
 }
 
-static void vga_set_palette(struct vc_data *vc, unsigned char *table)
+static void vga_set_palette(struct vc_data *vc, const unsigned char *table)
 {
 	int i, j;
 
@@ -860,7 +859,7 @@
 	}
 }
 
-static int vgacon_set_palette(struct vc_data *vc, unsigned char *table)
+static int vgacon_set_palette(struct vc_data *vc, const unsigned char *table)
 {
 #ifdef CAN_LOAD_PALETTE
 	if (vga_video_type != VIDEO_TYPE_VGAC || vga_palette_blanked
diff --git a/include/linux/console.h b/include/linux/console.h
index ea731af..137ac1a 100644
--- a/include/linux/console.h
+++ b/include/linux/console.h
@@ -47,7 +47,7 @@
 	int	(*con_font_copy)(struct vc_data *, int);
 	int     (*con_resize)(struct vc_data *, unsigned int, unsigned int,
 			       unsigned int);
-	int	(*con_set_palette)(struct vc_data *, unsigned char *);
+	int	(*con_set_palette)(struct vc_data *, const unsigned char *);
 	int	(*con_scrolldelta)(struct vc_data *, int);
 	int	(*con_set_origin)(struct vc_data *);
 	void	(*con_save_screen)(struct vc_data *);
diff --git a/include/linux/selection.h b/include/linux/selection.h
index 85193aa..8e4624e 100644
--- a/include/linux/selection.h
+++ b/include/linux/selection.h
@@ -24,10 +24,10 @@
 
 extern int console_blanked;
 
-extern unsigned char color_table[];
-extern int default_red[];
-extern int default_grn[];
-extern int default_blu[];
+extern const unsigned char color_table[];
+extern unsigned char default_red[];
+extern unsigned char default_grn[];
+extern unsigned char default_blu[];
 
 extern unsigned short *screen_pos(struct vc_data *vc, int w_offset, int viewed);
 extern u16 screen_glyph(struct vc_data *vc, int offset);
diff --git a/include/linux/serial_8250.h b/include/linux/serial_8250.h
index 4348797..48ec765 100644
--- a/include/linux/serial_8250.h
+++ b/include/linux/serial_8250.h
@@ -36,6 +36,7 @@
 	void		(*set_termios)(struct uart_port *,
 			               struct ktermios *new,
 			               struct ktermios *old);
+	unsigned int	(*get_mctrl)(struct uart_port *);
 	int		(*handle_irq)(struct uart_port *);
 	void		(*pm)(struct uart_port *, unsigned int state,
 			      unsigned old);
@@ -148,6 +149,7 @@
 					 const char *options);
 extern void serial8250_do_set_termios(struct uart_port *port,
 		struct ktermios *termios, struct ktermios *old);
+extern unsigned int serial8250_do_get_mctrl(struct uart_port *port);
 extern int serial8250_do_startup(struct uart_port *port);
 extern void serial8250_do_shutdown(struct uart_port *port);
 extern void serial8250_do_pm(struct uart_port *port, unsigned int state,
diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h
index cbfcf38..a3d7c0d 100644
--- a/include/linux/serial_core.h
+++ b/include/linux/serial_core.h
@@ -123,6 +123,7 @@
 	void			(*set_termios)(struct uart_port *,
 				               struct ktermios *new,
 				               struct ktermios *old);
+	unsigned int		(*get_mctrl)(struct uart_port *);
 	void			(*set_mctrl)(struct uart_port *, unsigned int);
 	int			(*startup)(struct uart_port *port);
 	void			(*shutdown)(struct uart_port *port);
@@ -281,6 +282,8 @@
 	enum uart_pm_state	pm_state;
 	struct circ_buf		xmit;
 
+	atomic_t		refcount;
+	wait_queue_head_t	remove_wait;
 	struct uart_port	*uart_port;
 };
 
diff --git a/include/linux/tty.h b/include/linux/tty.h
index 17b247c..40144f3 100644
--- a/include/linux/tty.h
+++ b/include/linux/tty.h
@@ -228,7 +228,8 @@
 	int			count;		/* Usage count */
 	wait_queue_head_t	open_wait;	/* Open waiters */
 	wait_queue_head_t	delta_msr_wait;	/* Modem status change */
-	unsigned long		flags;		/* TTY flags ASY_*/
+	unsigned long		flags;		/* User TTY flags ASYNC_ */
+	unsigned long		iflags;		/* Internal flags TTY_PORT_ */
 	unsigned char		console:1,	/* port is a console */
 				low_latency:1;	/* optional: tune for latency */
 	struct mutex		mutex;		/* Locking */
@@ -242,6 +243,18 @@
 	struct kref		kref;		/* Ref counter */
 };
 
+/* tty_port::iflags bits -- use atomic bit ops */
+#define TTY_PORT_INITIALIZED	0	/* device is initialized */
+#define TTY_PORT_SUSPENDED	1	/* device is suspended */
+#define TTY_PORT_ACTIVE		2	/* device is open */
+
+/*
+ * uart drivers: use the uart_port::status field and the UPSTAT_* defines
+ * for s/w-based flow control steering and carrier detection status
+ */
+#define TTY_PORT_CTS_FLOW	3	/* h/w flow control enabled */
+#define TTY_PORT_CHECK_CD	4	/* carrier detect enabled */
+
 /*
  * Where all of the state associated with a tty is kept while the tty
  * is open.  Since the termios state should be kept even if the tty
@@ -338,7 +351,6 @@
 #define TTY_OTHER_CLOSED 	2	/* Other side (if any) has closed */
 #define TTY_EXCLUSIVE 		3	/* Exclusive open mode */
 #define TTY_DO_WRITE_WAKEUP 	5	/* Call write_wakeup after queuing new */
-#define TTY_OTHER_DONE		6	/* Closed pty has completed input processing */
 #define TTY_LDISC_OPEN	 	11	/* Line discipline is open */
 #define TTY_PTY_LOCK 		16	/* pty private */
 #define TTY_NO_WRITE_SPLIT 	17	/* Preserve write boundaries to driver */
@@ -360,6 +372,16 @@
 	smp_mb();
 }
 
+static inline bool tty_io_error(struct tty_struct *tty)
+{
+	return test_bit(TTY_IO_ERROR, &tty->flags);
+}
+
+static inline bool tty_throttled(struct tty_struct *tty)
+{
+	return test_bit(TTY_THROTTLED, &tty->flags);
+}
+
 #ifdef CONFIG_TTY
 extern void console_init(void);
 extern void tty_kref_put(struct tty_struct *tty);
@@ -459,6 +481,7 @@
 extern void tty_buffer_set_lock_subclass(struct tty_port *port);
 extern bool tty_buffer_restart_work(struct tty_port *port);
 extern bool tty_buffer_cancel_work(struct tty_port *port);
+extern void tty_buffer_flush_work(struct tty_port *port);
 extern speed_t tty_termios_baud_rate(struct ktermios *termios);
 extern speed_t tty_termios_input_baud_rate(struct ktermios *termios);
 extern void tty_termios_encode_baud_rate(struct ktermios *termios,
@@ -539,7 +562,67 @@
 /* If the cts flow control is enabled, return true. */
 static inline bool tty_port_cts_enabled(struct tty_port *port)
 {
-	return port->flags & ASYNC_CTS_FLOW;
+	return test_bit(TTY_PORT_CTS_FLOW, &port->iflags);
+}
+
+static inline void tty_port_set_cts_flow(struct tty_port *port, bool val)
+{
+	if (val)
+		set_bit(TTY_PORT_CTS_FLOW, &port->iflags);
+	else
+		clear_bit(TTY_PORT_CTS_FLOW, &port->iflags);
+}
+
+static inline bool tty_port_active(struct tty_port *port)
+{
+	return test_bit(TTY_PORT_ACTIVE, &port->iflags);
+}
+
+static inline void tty_port_set_active(struct tty_port *port, bool val)
+{
+	if (val)
+		set_bit(TTY_PORT_ACTIVE, &port->iflags);
+	else
+		clear_bit(TTY_PORT_ACTIVE, &port->iflags);
+}
+
+static inline bool tty_port_check_carrier(struct tty_port *port)
+{
+	return test_bit(TTY_PORT_CHECK_CD, &port->iflags);
+}
+
+static inline void tty_port_set_check_carrier(struct tty_port *port, bool val)
+{
+	if (val)
+		set_bit(TTY_PORT_CHECK_CD, &port->iflags);
+	else
+		clear_bit(TTY_PORT_CHECK_CD, &port->iflags);
+}
+
+static inline bool tty_port_suspended(struct tty_port *port)
+{
+	return test_bit(TTY_PORT_SUSPENDED, &port->iflags);
+}
+
+static inline void tty_port_set_suspended(struct tty_port *port, bool val)
+{
+	if (val)
+		set_bit(TTY_PORT_SUSPENDED, &port->iflags);
+	else
+		clear_bit(TTY_PORT_SUSPENDED, &port->iflags);
+}
+
+static inline bool tty_port_initialized(struct tty_port *port)
+{
+	return test_bit(TTY_PORT_INITIALIZED, &port->iflags);
+}
+
+static inline void tty_port_set_initialized(struct tty_port *port, bool val)
+{
+	if (val)
+		set_bit(TTY_PORT_INITIALIZED, &port->iflags);
+	else
+		clear_bit(TTY_PORT_INITIALIZED, &port->iflags);
 }
 
 extern struct tty_struct *tty_port_tty_get(struct tty_port *port);
diff --git a/include/uapi/linux/serial_core.h b/include/uapi/linux/serial_core.h
index 24da334..99dbed8 100644
--- a/include/uapi/linux/serial_core.h
+++ b/include/uapi/linux/serial_core.h
@@ -267,4 +267,7 @@
 /* Microchip PIC32 UART */
 #define PORT_PIC32	115
 
+/* MPS2 UART */
+#define PORT_MPS2UART	116
+
 #endif /* _UAPILINUX_SERIAL_CORE_H */
diff --git a/include/uapi/linux/tty_flags.h b/include/uapi/linux/tty_flags.h
index 072e41e..66e4d8b 100644
--- a/include/uapi/linux/tty_flags.h
+++ b/include/uapi/linux/tty_flags.h
@@ -32,7 +32,13 @@
 #define ASYNCB_MAGIC_MULTIPLIER	16 /* Use special CLK or divisor */
 #define ASYNCB_LAST_USER	16
 
-/* Internal flags used only by kernel */
+/*
+ * Internal flags used only by kernel (read-only)
+ *
+ * WARNING: These flags are no longer used and have been superceded by the
+ *	    TTY_PORT_ flags in the iflags field (and not userspace-visible)
+ */
+#ifndef _KERNEL_
 #define ASYNCB_INITIALIZED	31 /* Serial port was initialized */
 #define ASYNCB_SUSPENDED	30 /* Serial port is suspended */
 #define ASYNCB_NORMAL_ACTIVE	29 /* Normal device is active */
@@ -43,7 +49,9 @@
 #define ASYNCB_SHARE_IRQ	24 /* for multifunction cards, no longer used */
 #define ASYNCB_CONS_FLOW	23 /* flow control for console  */
 #define ASYNCB_FIRST_KERNEL	22
+#endif
 
+/* Masks */
 #define ASYNC_HUP_NOTIFY	(1U << ASYNCB_HUP_NOTIFY)
 #define ASYNC_SUSPENDED		(1U << ASYNCB_SUSPENDED)
 #define ASYNC_FOURPORT		(1U << ASYNCB_FOURPORT)
@@ -72,6 +80,8 @@
 #define ASYNC_SPD_WARP		(ASYNC_SPD_HI|ASYNC_SPD_SHI)
 #define ASYNC_SPD_MASK		(ASYNC_SPD_HI|ASYNC_SPD_VHI|ASYNC_SPD_SHI)
 
+#ifndef _KERNEL_
+/* These flags are no longer used (and were always masked from userspace) */
 #define ASYNC_INITIALIZED	(1U << ASYNCB_INITIALIZED)
 #define ASYNC_NORMAL_ACTIVE	(1U << ASYNCB_NORMAL_ACTIVE)
 #define ASYNC_BOOT_AUTOCONF	(1U << ASYNCB_BOOT_AUTOCONF)
@@ -81,5 +91,6 @@
 #define ASYNC_SHARE_IRQ		(1U << ASYNCB_SHARE_IRQ)
 #define ASYNC_CONS_FLOW		(1U << ASYNCB_CONS_FLOW)
 #define ASYNC_INTERNAL_FLAGS	(~((1U << ASYNCB_FIRST_KERNEL) - 1))
+#endif
 
 #endif
diff --git a/include/uapi/linux/vt.h b/include/uapi/linux/vt.h
index 978578b..f690348 100644
--- a/include/uapi/linux/vt.h
+++ b/include/uapi/linux/vt.h
@@ -8,7 +8,6 @@
  */
 #define MIN_NR_CONSOLES 1       /* must be at least 1 */
 #define MAX_NR_CONSOLES	63	/* serial lines start at 64 */
-#define MAX_NR_USER_CONSOLES 63	/* must be root to allocate above this */
 		/* Note: the ioctl VT_GETSTATE does not work for
 		   consoles 16 and higher (since it returns a short) */
 
diff --git a/net/irda/ircomm/ircomm_tty.c b/net/irda/ircomm/ircomm_tty.c
index da126ee..873c4b7 100644
--- a/net/irda/ircomm/ircomm_tty.c
+++ b/net/irda/ircomm/ircomm_tty.c
@@ -220,10 +220,11 @@
 	IRDA_ASSERT(self->magic == IRCOMM_TTY_MAGIC, return -1;);
 
 	/* Check if already open */
-	if (test_and_set_bit(ASYNCB_INITIALIZED, &self->port.flags)) {
+	if (tty_port_initialized(&self->port)) {
 		pr_debug("%s(), already open so break out!\n", __func__);
 		return 0;
 	}
+	tty_port_set_initialized(&self->port, 1);
 
 	/* Register with IrCOMM */
 	irda_notify_init(&notify);
@@ -257,7 +258,7 @@
 
 	return 0;
 err:
-	clear_bit(ASYNCB_INITIALIZED, &self->port.flags);
+	tty_port_set_initialized(&self->port, 0);
 	return ret;
 }
 
@@ -280,8 +281,8 @@
 	 * If non-blocking mode is set, or the port is not enabled,
 	 * then make the check up front and then exit.
 	 */
-	if (test_bit(TTY_IO_ERROR, &tty->flags)) {
-		port->flags |= ASYNC_NORMAL_ACTIVE;
+	if (tty_io_error(tty)) {
+		tty_port_set_active(port, 1);
 		return 0;
 	}
 
@@ -289,7 +290,7 @@
 		/* nonblock mode is set */
 		if (C_BAUD(tty))
 			tty_port_raise_dtr_rts(port);
-		port->flags |= ASYNC_NORMAL_ACTIVE;
+		tty_port_set_active(port, 1);
 		pr_debug("%s(), O_NONBLOCK requested!\n", __func__);
 		return 0;
 	}
@@ -318,13 +319,12 @@
 	spin_unlock_irqrestore(&port->lock, flags);
 
 	while (1) {
-		if (C_BAUD(tty) && test_bit(ASYNCB_INITIALIZED, &port->flags))
+		if (C_BAUD(tty) && tty_port_initialized(port))
 			tty_port_raise_dtr_rts(port);
 
 		set_current_state(TASK_INTERRUPTIBLE);
 
-		if (tty_hung_up_p(filp) ||
-		    !test_bit(ASYNCB_INITIALIZED, &port->flags)) {
+		if (tty_hung_up_p(filp) || !tty_port_initialized(port)) {
 			retval = (port->flags & ASYNC_HUP_NOTIFY) ?
 					-EAGAIN : -ERESTARTSYS;
 			break;
@@ -365,7 +365,7 @@
 		 __FILE__, __LINE__, tty->driver->name, port->count);
 
 	if (!retval)
-		port->flags |= ASYNC_NORMAL_ACTIVE;
+		tty_port_set_active(port, 1);
 
 	return retval;
 }
@@ -876,8 +876,9 @@
 	IRDA_ASSERT(self != NULL, return;);
 	IRDA_ASSERT(self->magic == IRCOMM_TTY_MAGIC, return;);
 
-	if (!test_and_clear_bit(ASYNCB_INITIALIZED, &self->port.flags))
+	if (!tty_port_initialized(&self->port))
 		return;
+	tty_port_set_initialized(&self->port, 0);
 
 	ircomm_tty_detach_cable(self);
 
@@ -925,7 +926,6 @@
 	ircomm_tty_shutdown(self);
 
 	spin_lock_irqsave(&port->lock, flags);
-	port->flags &= ~ASYNC_NORMAL_ACTIVE;
 	if (port->tty) {
 		set_bit(TTY_IO_ERROR, &port->tty->flags);
 		tty_kref_put(port->tty);
@@ -933,6 +933,7 @@
 	port->tty = NULL;
 	port->count = 0;
 	spin_unlock_irqrestore(&port->lock, flags);
+	tty_port_set_active(port, 0);
 
 	wake_up_interruptible(&port->open_wait);
 }
@@ -999,7 +1000,7 @@
 	if (status & IRCOMM_DCE_DELTA_ANY) {
 		/*wake_up_interruptible(&self->delta_msr_wait);*/
 	}
-	if ((self->port.flags & ASYNC_CHECK_CD) && (status & IRCOMM_DELTA_CD)) {
+	if (tty_port_check_carrier(&self->port) && (status & IRCOMM_DELTA_CD)) {
 		pr_debug("%s(), ircomm%d CD now %s...\n", __func__ , self->line,
 			 (status & IRCOMM_CD) ? "on" : "off");
 
@@ -1255,11 +1256,11 @@
 		seq_printf(m, "%cASYNC_CTS_FLOW", sep);
 		sep = '|';
 	}
-	if (self->port.flags & ASYNC_CHECK_CD) {
+	if (tty_port_check_carrier(&self->port)) {
 		seq_printf(m, "%cASYNC_CHECK_CD", sep);
 		sep = '|';
 	}
-	if (self->port.flags & ASYNC_INITIALIZED) {
+	if (tty_port_initialized(&self->port)) {
 		seq_printf(m, "%cASYNC_INITIALIZED", sep);
 		sep = '|';
 	}
@@ -1267,7 +1268,7 @@
 		seq_printf(m, "%cASYNC_LOW_LATENCY", sep);
 		sep = '|';
 	}
-	if (self->port.flags & ASYNC_NORMAL_ACTIVE) {
+	if (tty_port_active(&self->port)) {
 		seq_printf(m, "%cASYNC_NORMAL_ACTIVE", sep);
 		sep = '|';
 	}
diff --git a/net/irda/ircomm/ircomm_tty_attach.c b/net/irda/ircomm/ircomm_tty_attach.c
index 61137f8..0a41101 100644
--- a/net/irda/ircomm/ircomm_tty_attach.c
+++ b/net/irda/ircomm/ircomm_tty_attach.c
@@ -968,7 +968,7 @@
 		ircomm_tty_next_state(self, IRCOMM_TTY_SEARCH);
 		ircomm_tty_start_watchdog_timer(self, 3*HZ);
 
-		if (self->port.flags & ASYNC_CHECK_CD) {
+		if (tty_port_check_carrier(&self->port)) {
 			/* Drop carrier */
 			self->settings.dce = IRCOMM_DELTA_CD;
 			ircomm_tty_check_modem_status(self);
diff --git a/net/irda/ircomm/ircomm_tty_ioctl.c b/net/irda/ircomm/ircomm_tty_ioctl.c
index d3687aa..d4fdf8f 100644
--- a/net/irda/ircomm/ircomm_tty_ioctl.c
+++ b/net/irda/ircomm/ircomm_tty_ioctl.c
@@ -86,21 +86,17 @@
 	ircomm_param_request(self, IRCOMM_DATA_RATE, FALSE);
 
 	/* CTS flow control flag and modem status interrupts */
+	tty_port_set_cts_flow(&self->port, cflag & CRTSCTS);
 	if (cflag & CRTSCTS) {
-		self->port.flags |= ASYNC_CTS_FLOW;
 		self->settings.flow_control |= IRCOMM_RTS_CTS_IN;
 		/* This got me. Bummer. Jean II */
 		if (self->service_type == IRCOMM_3_WIRE_RAW)
 			net_warn_ratelimited("%s(), enabling RTS/CTS on link that doesn't support it (3-wire-raw)\n",
 					     __func__);
 	} else {
-		self->port.flags &= ~ASYNC_CTS_FLOW;
 		self->settings.flow_control &= ~IRCOMM_RTS_CTS_IN;
 	}
-	if (cflag & CLOCAL)
-		self->port.flags &= ~ASYNC_CHECK_CD;
-	else
-		self->port.flags |= ASYNC_CHECK_CD;
+	tty_port_set_check_carrier(&self->port, ~cflag & CLOCAL);
 #if 0
 	/*
 	 * Set up parity check flag
@@ -166,7 +162,7 @@
 	/* Handle transition away from B0 status */
 	if (!(old_termios->c_cflag & CBAUD) && (cflag & CBAUD)) {
 		self->settings.dte |= IRCOMM_DTR;
-		if (!C_CRTSCTS(tty) || !test_bit(TTY_THROTTLED, &tty->flags))
+		if (!C_CRTSCTS(tty) || !tty_throttled(tty))
 			self->settings.dte |= IRCOMM_RTS;
 		ircomm_param_request(self, IRCOMM_DTE, TRUE);
 	}
@@ -190,7 +186,7 @@
 	struct ircomm_tty_cb *self = (struct ircomm_tty_cb *) tty->driver_data;
 	unsigned int result;
 
-	if (tty->flags & (1 << TTY_IO_ERROR))
+	if (tty_io_error(tty))
 		return -EIO;
 
 	result =  ((self->settings.dte & IRCOMM_RTS) ? TIOCM_RTS : 0)
@@ -213,7 +209,7 @@
 {
 	struct ircomm_tty_cb *self = (struct ircomm_tty_cb *) tty->driver_data;
 
-	if (tty->flags & (1 << TTY_IO_ERROR))
+	if (tty_io_error(tty))
 		return -EIO;
 
 	IRDA_ASSERT(self != NULL, return -1;);
@@ -328,7 +324,7 @@
 
  check_and_exit:
 
-	if (self->flags & ASYNC_INITIALIZED) {
+	if (tty_port_initialized(self)) {
 		if (((old_state.flags & ASYNC_SPD_MASK) !=
 		     (self->flags & ASYNC_SPD_MASK)) ||
 		    (old_driver.custom_divisor != driver->custom_divisor)) {
@@ -362,7 +358,7 @@
 	if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
 	    (cmd != TIOCSERCONFIG) && (cmd != TIOCSERGSTRUCT) &&
 	    (cmd != TIOCMIWAIT) && (cmd != TIOCGICOUNT)) {
-		if (tty->flags & (1 << TTY_IO_ERROR))
+		if (tty_io_error(tty))
 		    return -EIO;
 	}