spi: controller driver for Designware SPI core
Driver for the Designware SPI core, it supports multipul interfaces like
PCI/APB etc. User can use "dw_apb_ssi_db.pdf" from Synopsys as HW
datasheet.
[randy.dunlap@oracle.com: fix build]
[akpm@linux-foundation.org: build fix]
Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
diff --git a/include/linux/spi/dw_spi.h b/include/linux/spi/dw_spi.h
new file mode 100644
index 0000000..51b3e77
--- /dev/null
+++ b/include/linux/spi/dw_spi.h
@@ -0,0 +1,212 @@
+#ifndef DW_SPI_HEADER_H
+#define DW_SPI_HEADER_H
+#include <linux/io.h>
+
+/* Bit fields in CTRLR0 */
+#define SPI_DFS_OFFSET 0
+
+#define SPI_FRF_OFFSET 4
+#define SPI_FRF_SPI 0x0
+#define SPI_FRF_SSP 0x1
+#define SPI_FRF_MICROWIRE 0x2
+#define SPI_FRF_RESV 0x3
+
+#define SPI_MODE_OFFSET 6
+#define SPI_SCPH_OFFSET 6
+#define SPI_SCOL_OFFSET 7
+#define SPI_TMOD_OFFSET 8
+#define SPI_TMOD_TR 0x0 /* xmit & recv */
+#define SPI_TMOD_TO 0x1 /* xmit only */
+#define SPI_TMOD_RO 0x2 /* recv only */
+#define SPI_TMOD_EPROMREAD 0x3 /* eeprom read mode */
+
+#define SPI_SLVOE_OFFSET 10
+#define SPI_SRL_OFFSET 11
+#define SPI_CFS_OFFSET 12
+
+/* Bit fields in SR, 7 bits */
+#define SR_MASK 0x7f /* cover 7 bits */
+#define SR_BUSY (1 << 0)
+#define SR_TF_NOT_FULL (1 << 1)
+#define SR_TF_EMPT (1 << 2)
+#define SR_RF_NOT_EMPT (1 << 3)
+#define SR_RF_FULL (1 << 4)
+#define SR_TX_ERR (1 << 5)
+#define SR_DCOL (1 << 6)
+
+/* Bit fields in ISR, IMR, RISR, 7 bits */
+#define SPI_INT_TXEI (1 << 0)
+#define SPI_INT_TXOI (1 << 1)
+#define SPI_INT_RXUI (1 << 2)
+#define SPI_INT_RXOI (1 << 3)
+#define SPI_INT_RXFI (1 << 4)
+#define SPI_INT_MSTI (1 << 5)
+
+/* TX RX interrupt level threshhold, max can be 256 */
+#define SPI_INT_THRESHOLD 32
+
+enum dw_ssi_type {
+ SSI_MOTO_SPI = 0,
+ SSI_TI_SSP,
+ SSI_NS_MICROWIRE,
+};
+
+struct dw_spi_reg {
+ u32 ctrl0;
+ u32 ctrl1;
+ u32 ssienr;
+ u32 mwcr;
+ u32 ser;
+ u32 baudr;
+ u32 txfltr;
+ u32 rxfltr;
+ u32 txflr;
+ u32 rxflr;
+ u32 sr;
+ u32 imr;
+ u32 isr;
+ u32 risr;
+ u32 txoicr;
+ u32 rxoicr;
+ u32 rxuicr;
+ u32 msticr;
+ u32 icr;
+ u32 dmacr;
+ u32 dmatdlr;
+ u32 dmardlr;
+ u32 idr;
+ u32 version;
+ u32 dr; /* Currently oper as 32 bits,
+ though only low 16 bits matters */
+} __packed;
+
+struct dw_spi {
+ struct spi_master *master;
+ struct spi_device *cur_dev;
+ struct device *parent_dev;
+ enum dw_ssi_type type;
+
+ void __iomem *regs;
+ unsigned long paddr;
+ u32 iolen;
+ int irq;
+ u32 max_freq; /* max bus freq supported */
+
+ u16 bus_num;
+ u16 num_cs; /* supported slave numbers */
+
+ /* Driver message queue */
+ struct workqueue_struct *workqueue;
+ struct work_struct pump_messages;
+ spinlock_t lock;
+ struct list_head queue;
+ int busy;
+ int run;
+
+ /* Message Transfer pump */
+ struct tasklet_struct pump_transfers;
+
+ /* Current message transfer state info */
+ struct spi_message *cur_msg;
+ struct spi_transfer *cur_transfer;
+ struct chip_data *cur_chip;
+ struct chip_data *prev_chip;
+ size_t len;
+ void *tx;
+ void *tx_end;
+ void *rx;
+ void *rx_end;
+ int dma_mapped;
+ dma_addr_t rx_dma;
+ dma_addr_t tx_dma;
+ size_t rx_map_len;
+ size_t tx_map_len;
+ u8 n_bytes; /* current is a 1/2 bytes op */
+ u8 max_bits_per_word; /* maxim is 16b */
+ u32 dma_width;
+ int cs_change;
+ int (*write)(struct dw_spi *dws);
+ int (*read)(struct dw_spi *dws);
+ irqreturn_t (*transfer_handler)(struct dw_spi *dws);
+ void (*cs_control)(u32 command);
+
+ /* Dma info */
+ int dma_inited;
+ struct dma_chan *txchan;
+ struct dma_chan *rxchan;
+ int txdma_done;
+ int rxdma_done;
+ u64 tx_param;
+ u64 rx_param;
+ struct device *dma_dev;
+ dma_addr_t dma_addr;
+
+ /* Bus interface info */
+ void *priv;
+#ifdef CONFIG_DEBUG_FS
+ struct dentry *debugfs;
+#endif
+};
+
+#define dw_readl(dw, name) \
+ __raw_readl(&(((struct dw_spi_reg *)dw->regs)->name))
+#define dw_writel(dw, name, val) \
+ __raw_writel((val), &(((struct dw_spi_reg *)dw->regs)->name))
+#define dw_readw(dw, name) \
+ __raw_readw(&(((struct dw_spi_reg *)dw->regs)->name))
+#define dw_writew(dw, name, val) \
+ __raw_writew((val), &(((struct dw_spi_reg *)dw->regs)->name))
+
+static inline void spi_enable_chip(struct dw_spi *dws, int enable)
+{
+ dw_writel(dws, ssienr, (enable ? 1 : 0));
+}
+
+static inline void spi_set_clk(struct dw_spi *dws, u16 div)
+{
+ dw_writel(dws, baudr, div);
+}
+
+static inline void spi_chip_sel(struct dw_spi *dws, u16 cs)
+{
+ if (cs > dws->num_cs)
+ return;
+ dw_writel(dws, ser, 1 << cs);
+}
+
+/* Disable IRQ bits */
+static inline void spi_mask_intr(struct dw_spi *dws, u32 mask)
+{
+ u32 new_mask;
+
+ new_mask = dw_readl(dws, imr) & ~mask;
+ dw_writel(dws, imr, new_mask);
+}
+
+/* Enable IRQ bits */
+static inline void spi_umask_intr(struct dw_spi *dws, u32 mask)
+{
+ u32 new_mask;
+
+ new_mask = dw_readl(dws, imr) | mask;
+ dw_writel(dws, imr, new_mask);
+}
+
+/*
+ * Each SPI slave device to work with dw_api controller should
+ * has such a structure claiming its working mode (PIO/DMA etc),
+ * which can be save in the "controller_data" member of the
+ * struct spi_device
+ */
+struct dw_spi_chip {
+ u8 poll_mode; /* 0 for contoller polling mode */
+ u8 type; /* SPI/SSP/Micrwire */
+ u8 enable_dma;
+ void (*cs_control)(u32 command);
+};
+
+extern int dw_spi_add_host(struct dw_spi *dws);
+extern void dw_spi_remove_host(struct dw_spi *dws);
+extern int dw_spi_suspend_host(struct dw_spi *dws);
+extern int dw_spi_resume_host(struct dw_spi *dws);
+#endif /* DW_SPI_HEADER_H */