tg3: Add MDI-X reporting
This patch adds MDI-X state reporting.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c
index 6a25e58..0acb279 100644
--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -3932,6 +3932,7 @@
current_link_up = 0;
current_speed = SPEED_INVALID;
current_duplex = DUPLEX_INVALID;
+ tp->phy_flags &= ~TG3_PHYFLG_MDIX_STATE;
if (tp->phy_flags & TG3_PHYFLG_CAPACITIVE_COUPLING) {
err = tg3_phy_auxctl_read(tp,
@@ -4004,8 +4005,22 @@
}
if (current_link_up == 1 &&
- tp->link_config.active_duplex == DUPLEX_FULL)
+ tp->link_config.active_duplex == DUPLEX_FULL) {
+ u32 reg, bit;
+
+ if (tp->phy_flags & TG3_PHYFLG_IS_FET) {
+ reg = MII_TG3_FET_GEN_STAT;
+ bit = MII_TG3_FET_GEN_STAT_MDIXSTAT;
+ } else {
+ reg = MII_TG3_EXT_STAT;
+ bit = MII_TG3_EXT_STAT_MDIX;
+ }
+
+ if (!tg3_readphy(tp, reg, &val) && (val & bit))
+ tp->phy_flags |= TG3_PHYFLG_MDIX_STATE;
+
tg3_setup_flow_control(tp, lcl_adv, rmt_adv);
+ }
}
relink:
@@ -10290,9 +10305,16 @@
if (netif_running(dev)) {
ethtool_cmd_speed_set(cmd, tp->link_config.active_speed);
cmd->duplex = tp->link_config.active_duplex;
+ if (!(tp->phy_flags & TG3_PHYFLG_ANY_SERDES)) {
+ if (tp->phy_flags & TG3_PHYFLG_MDIX_STATE)
+ cmd->eth_tp_mdix = ETH_TP_MDI_X;
+ else
+ cmd->eth_tp_mdix = ETH_TP_MDI;
+ }
} else {
ethtool_cmd_speed_set(cmd, SPEED_INVALID);
cmd->duplex = DUPLEX_INVALID;
+ cmd->eth_tp_mdix = ETH_TP_MDI_INVALID;
}
cmd->phy_address = tp->phy_addr;
cmd->transceiver = XCVR_INTERNAL;
diff --git a/drivers/net/ethernet/broadcom/tg3.h b/drivers/net/ethernet/broadcom/tg3.h
index 8e2f380..9cc10a8 100644
--- a/drivers/net/ethernet/broadcom/tg3.h
+++ b/drivers/net/ethernet/broadcom/tg3.h
@@ -2174,6 +2174,7 @@
#define MII_TG3_EXT_CTRL_TBI 0x8000
#define MII_TG3_EXT_STAT 0x11 /* Extended status register */
+#define MII_TG3_EXT_STAT_MDIX 0x2000
#define MII_TG3_EXT_STAT_LPASS 0x0100
#define MII_TG3_RXR_COUNTERS 0x14 /* Local/Remote Receiver Counts */
@@ -2277,6 +2278,9 @@
#define MII_TG3_FET_PTEST_FRC_TX_LINK 0x1000
#define MII_TG3_FET_PTEST_FRC_TX_LOCK 0x0800
+#define MII_TG3_FET_GEN_STAT 0x1c
+#define MII_TG3_FET_GEN_STAT_MDIXSTAT 0x2000
+
#define MII_TG3_FET_TEST 0x1f
#define MII_TG3_FET_SHADOW_EN 0x0080
@@ -3135,6 +3139,7 @@
#define TG3_PHYFLG_SERDES_PREEMPHASIS 0x00010000
#define TG3_PHYFLG_PARALLEL_DETECT 0x00020000
#define TG3_PHYFLG_EEE_CAP 0x00040000
+#define TG3_PHYFLG_MDIX_STATE 0x00200000
u32 led_ctrl;
u32 phy_otp;