ARM: dts: msm: Add support for modem on MSM8953
Add support for modem which facilitates the loading
of modem firmware, authentication and bringing it
out of reset.
Change-Id: I7c34271b47e8d13ac844e2b906c56d58600eb942
Signed-off-by: Jingbiao Lu <jingbiao@codeaurora.org>
diff --git a/arch/arm64/boot/dts/qcom/msm8953.dtsi b/arch/arm64/boot/dts/qcom/msm8953.dtsi
index b4631e9..0d76af8 100644
--- a/arch/arm64/boot/dts/qcom/msm8953.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8953.dtsi
@@ -1,5 +1,5 @@
/*
- * Copyright (c) 2015-2017, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2015-2018, The Linux Foundation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 and
@@ -1788,6 +1788,47 @@
qcom,reset-ep-after-lpm-resume;
};
+ qcom,mss@4080000 {
+ compatible = "qcom,pil-q6v55-mss";
+ reg = <0x04080000 0x100>,
+ <0x0194f000 0x010>,
+ <0x01950000 0x008>,
+ <0x01951000 0x008>,
+ <0x04020000 0x040>,
+ <0x01871000 0x004>;
+ reg-names = "qdsp6_base", "halt_q6", "halt_modem", "halt_nc",
+ "rmb_base", "restart_reg";
+
+ interrupts = <GIC_SPI 24 IRQ_TYPE_EDGE_RISING>;
+ vdd_mss-supply = <&pm8953_s1>;
+ vdd_cx-supply = <&pm8953_s2_level>;
+ vdd_cx-voltage = <RPM_SMD_REGULATOR_LEVEL_TURBO>;
+ vdd_mx-supply = <&pm8953_s7_level_ao>;
+ vdd_mx-uV = <RPM_SMD_REGULATOR_LEVEL_TURBO>;
+ vdd_pll-supply = <&pm8953_l7>;
+ qcom,vdd_pll = <1800000>;
+ vdd_mss-uV = <RPM_SMD_REGULATOR_LEVEL_TURBO>;
+
+ clocks = <&clock_gcc clk_xo_pil_mss_clk>,
+ <&clock_gcc clk_gcc_mss_cfg_ahb_clk>,
+ <&clock_gcc clk_gcc_mss_q6_bimc_axi_clk>,
+ <&clock_gcc clk_gcc_boot_rom_ahb_clk>;
+ clock-names = "xo", "iface_clk", "bus_clk", "mem_clk";
+ qcom,proxy-clock-names = "xo";
+ qcom,active-clock-names = "iface_clk", "bus_clk", "mem_clk";
+
+ qcom,pas-id = <5>;
+ qcom,pil-mss-memsetup;
+ qcom,firmware-name = "modem";
+ qcom,pil-self-auth;
+ qcom,sysmon-id = <0>;
+ qcom,ssctl-instance-id = <0x12>;
+ qcom,qdsp6v56-1-10;
+ qcom,reset-clk;
+
+ memory-region = <&modem_mem>;
+ };
+
qcom,lpass@c200000 {
compatible = "qcom,pil-tz-generic";
reg = <0xc200000 0x00100>;