mcp23s08 spi gpio expander support
Basic driver for 8-bit SPI based MCP23S08 GPIO expander, without support for
IRQs or the shared chipselect mechanism.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 36d5d6a..d924a32 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -52,4 +52,11 @@
comment "SPI GPIO expanders:"
+config GPIO_MCP23S08
+ tristate "Microchip MCP23S08 I/O expander"
+ depends on SPI_MASTER
+ help
+ SPI driver for Microchip MCP23S08 I/O expander. This provides
+ a GPIO interface supporting inputs and outputs.
+
endmenu
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index b469ab2..a1fd877 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -4,4 +4,5 @@
obj-$(CONFIG_HAVE_GPIO_LIB) += gpiolib.o
+obj-$(CONFIG_GPIO_MCP23S08) += mcp23s08.o
obj-$(CONFIG_GPIO_PCF857X) += pcf857x.o
diff --git a/drivers/gpio/mcp23s08.c b/drivers/gpio/mcp23s08.c
new file mode 100644
index 0000000..bb60e8c
--- /dev/null
+++ b/drivers/gpio/mcp23s08.c
@@ -0,0 +1,357 @@
+/*
+ * mcp23s08.c - SPI gpio expander driver
+ */
+
+#include <linux/kernel.h>
+#include <linux/device.h>
+#include <linux/workqueue.h>
+#include <linux/mutex.h>
+
+#include <linux/spi/spi.h>
+#include <linux/spi/mcp23s08.h>
+
+#include <asm/gpio.h>
+
+
+/* Registers are all 8 bits wide.
+ *
+ * The mcp23s17 has twice as many bits, and can be configured to work
+ * with either 16 bit registers or with two adjacent 8 bit banks.
+ *
+ * Also, there are I2C versions of both chips.
+ */
+#define MCP_IODIR 0x00 /* init/reset: all ones */
+#define MCP_IPOL 0x01
+#define MCP_GPINTEN 0x02
+#define MCP_DEFVAL 0x03
+#define MCP_INTCON 0x04
+#define MCP_IOCON 0x05
+# define IOCON_SEQOP (1 << 5)
+# define IOCON_HAEN (1 << 3)
+# define IOCON_ODR (1 << 2)
+# define IOCON_INTPOL (1 << 1)
+#define MCP_GPPU 0x06
+#define MCP_INTF 0x07
+#define MCP_INTCAP 0x08
+#define MCP_GPIO 0x09
+#define MCP_OLAT 0x0a
+
+struct mcp23s08 {
+ struct spi_device *spi;
+ u8 addr;
+
+ /* lock protects the cached values */
+ struct mutex lock;
+ u8 cache[11];
+
+ struct gpio_chip chip;
+
+ struct work_struct work;
+};
+
+static int mcp23s08_read(struct mcp23s08 *mcp, unsigned reg)
+{
+ u8 tx[2], rx[1];
+ int status;
+
+ tx[0] = mcp->addr | 0x01;
+ tx[1] = reg;
+ status = spi_write_then_read(mcp->spi, tx, sizeof tx, rx, sizeof rx);
+ return (status < 0) ? status : rx[0];
+}
+
+static int mcp23s08_write(struct mcp23s08 *mcp, unsigned reg, u8 val)
+{
+ u8 tx[3];
+
+ tx[0] = mcp->addr;
+ tx[1] = reg;
+ tx[2] = val;
+ return spi_write_then_read(mcp->spi, tx, sizeof tx, NULL, 0);
+}
+
+static int
+mcp23s08_read_regs(struct mcp23s08 *mcp, unsigned reg, u8 *vals, unsigned n)
+{
+ u8 tx[2];
+
+ if ((n + reg) > sizeof mcp->cache)
+ return -EINVAL;
+ tx[0] = mcp->addr | 0x01;
+ tx[1] = reg;
+ return spi_write_then_read(mcp->spi, tx, sizeof tx, vals, n);
+}
+
+/*----------------------------------------------------------------------*/
+
+static int mcp23s08_direction_input(struct gpio_chip *chip, unsigned offset)
+{
+ struct mcp23s08 *mcp = container_of(chip, struct mcp23s08, chip);
+ int status;
+
+ mutex_lock(&mcp->lock);
+ mcp->cache[MCP_IODIR] |= (1 << offset);
+ status = mcp23s08_write(mcp, MCP_IODIR, mcp->cache[MCP_IODIR]);
+ mutex_unlock(&mcp->lock);
+ return status;
+}
+
+static int mcp23s08_get(struct gpio_chip *chip, unsigned offset)
+{
+ struct mcp23s08 *mcp = container_of(chip, struct mcp23s08, chip);
+ int status;
+
+ mutex_lock(&mcp->lock);
+
+ /* REVISIT reading this clears any IRQ ... */
+ status = mcp23s08_read(mcp, MCP_GPIO);
+ if (status < 0)
+ status = 0;
+ else {
+ mcp->cache[MCP_GPIO] = status;
+ status = !!(status & (1 << offset));
+ }
+ mutex_unlock(&mcp->lock);
+ return status;
+}
+
+static int __mcp23s08_set(struct mcp23s08 *mcp, unsigned mask, int value)
+{
+ u8 olat = mcp->cache[MCP_OLAT];
+
+ if (value)
+ olat |= mask;
+ else
+ olat &= ~mask;
+ mcp->cache[MCP_OLAT] = olat;
+ return mcp23s08_write(mcp, MCP_OLAT, olat);
+}
+
+static void mcp23s08_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+ struct mcp23s08 *mcp = container_of(chip, struct mcp23s08, chip);
+ u8 mask = 1 << offset;
+
+ mutex_lock(&mcp->lock);
+ __mcp23s08_set(mcp, mask, value);
+ mutex_unlock(&mcp->lock);
+}
+
+static int
+mcp23s08_direction_output(struct gpio_chip *chip, unsigned offset, int value)
+{
+ struct mcp23s08 *mcp = container_of(chip, struct mcp23s08, chip);
+ u8 mask = 1 << offset;
+ int status;
+
+ mutex_lock(&mcp->lock);
+ status = __mcp23s08_set(mcp, mask, value);
+ if (status == 0) {
+ mcp->cache[MCP_IODIR] &= ~mask;
+ status = mcp23s08_write(mcp, MCP_IODIR, mcp->cache[MCP_IODIR]);
+ }
+ mutex_unlock(&mcp->lock);
+ return status;
+}
+
+/*----------------------------------------------------------------------*/
+
+#ifdef CONFIG_DEBUG_FS
+
+#include <linux/seq_file.h>
+
+/*
+ * This shows more info than the generic gpio dump code:
+ * pullups, deglitching, open drain drive.
+ */
+static void mcp23s08_dbg_show(struct seq_file *s, struct gpio_chip *chip)
+{
+ struct mcp23s08 *mcp;
+ char bank;
+ unsigned t;
+ unsigned mask;
+
+ mcp = container_of(chip, struct mcp23s08, chip);
+
+ /* NOTE: we only handle one bank for now ... */
+ bank = '0' + ((mcp->addr >> 1) & 0x3);
+
+ mutex_lock(&mcp->lock);
+ t = mcp23s08_read_regs(mcp, 0, mcp->cache, sizeof mcp->cache);
+ if (t < 0) {
+ seq_printf(s, " I/O ERROR %d\n", t);
+ goto done;
+ }
+
+ for (t = 0, mask = 1; t < 8; t++, mask <<= 1) {
+ const char *label;
+
+ label = gpiochip_is_requested(chip, t);
+ if (!label)
+ continue;
+
+ seq_printf(s, " gpio-%-3d P%c.%d (%-12s) %s %s %s",
+ chip->base + t, bank, t, label,
+ (mcp->cache[MCP_IODIR] & mask) ? "in " : "out",
+ (mcp->cache[MCP_GPIO] & mask) ? "hi" : "lo",
+ (mcp->cache[MCP_GPPU] & mask) ? " " : "up");
+ /* NOTE: ignoring the irq-related registers */
+ seq_printf(s, "\n");
+ }
+done:
+ mutex_unlock(&mcp->lock);
+}
+
+#else
+#define mcp23s08_dbg_show NULL
+#endif
+
+/*----------------------------------------------------------------------*/
+
+static int mcp23s08_probe(struct spi_device *spi)
+{
+ struct mcp23s08 *mcp;
+ struct mcp23s08_platform_data *pdata;
+ int status;
+ int do_update = 0;
+
+ pdata = spi->dev.platform_data;
+ if (!pdata || pdata->slave > 3 || !pdata->base)
+ return -ENODEV;
+
+ mcp = kzalloc(sizeof *mcp, GFP_KERNEL);
+ if (!mcp)
+ return -ENOMEM;
+
+ mutex_init(&mcp->lock);
+
+ mcp->spi = spi;
+ mcp->addr = 0x40 | (pdata->slave << 1);
+
+ mcp->chip.label = "mcp23s08",
+
+ mcp->chip.direction_input = mcp23s08_direction_input;
+ mcp->chip.get = mcp23s08_get;
+ mcp->chip.direction_output = mcp23s08_direction_output;
+ mcp->chip.set = mcp23s08_set;
+ mcp->chip.dbg_show = mcp23s08_dbg_show;
+
+ mcp->chip.base = pdata->base;
+ mcp->chip.ngpio = 8;
+ mcp->chip.can_sleep = 1;
+
+ spi_set_drvdata(spi, mcp);
+
+ /* verify MCP_IOCON.SEQOP = 0, so sequential reads work */
+ status = mcp23s08_read(mcp, MCP_IOCON);
+ if (status < 0)
+ goto fail;
+ if (status & IOCON_SEQOP) {
+ status &= ~IOCON_SEQOP;
+ status = mcp23s08_write(mcp, MCP_IOCON, (u8) status);
+ if (status < 0)
+ goto fail;
+ }
+
+ /* configure ~100K pullups */
+ status = mcp23s08_write(mcp, MCP_GPPU, pdata->pullups);
+ if (status < 0)
+ goto fail;
+
+ status = mcp23s08_read_regs(mcp, 0, mcp->cache, sizeof mcp->cache);
+ if (status < 0)
+ goto fail;
+
+ /* disable inverter on input */
+ if (mcp->cache[MCP_IPOL] != 0) {
+ mcp->cache[MCP_IPOL] = 0;
+ do_update = 1;
+ }
+
+ /* disable irqs */
+ if (mcp->cache[MCP_GPINTEN] != 0) {
+ mcp->cache[MCP_GPINTEN] = 0;
+ do_update = 1;
+ }
+
+ if (do_update) {
+ u8 tx[4];
+
+ tx[0] = mcp->addr;
+ tx[1] = MCP_IPOL;
+ memcpy(&tx[2], &mcp->cache[MCP_IPOL], sizeof(tx) - 2);
+ status = spi_write_then_read(mcp->spi, tx, sizeof tx, NULL, 0);
+
+ /* FIXME check status... */
+ }
+
+ status = gpiochip_add(&mcp->chip);
+
+ /* NOTE: these chips have a relatively sane IRQ framework, with
+ * per-signal masking and level/edge triggering. It's not yet
+ * handled here...
+ */
+
+ if (pdata->setup) {
+ status = pdata->setup(spi, mcp->chip.base,
+ mcp->chip.ngpio, pdata->context);
+ if (status < 0)
+ dev_dbg(&spi->dev, "setup --> %d\n", status);
+ }
+
+ return 0;
+
+fail:
+ kfree(mcp);
+ return status;
+}
+
+static int mcp23s08_remove(struct spi_device *spi)
+{
+ struct mcp23s08 *mcp = spi_get_drvdata(spi);
+ struct mcp23s08_platform_data *pdata = spi->dev.platform_data;
+ int status = 0;
+
+ if (pdata->teardown) {
+ status = pdata->teardown(spi,
+ mcp->chip.base, mcp->chip.ngpio,
+ pdata->context);
+ if (status < 0) {
+ dev_err(&spi->dev, "%s --> %d\n", "teardown", status);
+ return status;
+ }
+ }
+
+ status = gpiochip_remove(&mcp->chip);
+ if (status == 0)
+ kfree(mcp);
+ else
+ dev_err(&spi->dev, "%s --> %d\n", "remove", status);
+ return status;
+}
+
+static struct spi_driver mcp23s08_driver = {
+ .probe = mcp23s08_probe,
+ .remove = mcp23s08_remove,
+ .driver = {
+ .name = "mcp23s08",
+ .owner = THIS_MODULE,
+ },
+};
+
+/*----------------------------------------------------------------------*/
+
+static int __init mcp23s08_init(void)
+{
+ return spi_register_driver(&mcp23s08_driver);
+}
+module_init(mcp23s08_init);
+
+static void __exit mcp23s08_exit(void)
+{
+ spi_unregister_driver(&mcp23s08_driver);
+}
+module_exit(mcp23s08_exit);
+
+MODULE_LICENSE("GPL");
+