[TC] defxx: TURBOchannel support
This is a set of changes to add TURBOchannel support to the defxx driver. As
at this point the EISA support in the driver has become the only not having
been converted to the driver model, I took the opportunity to convert it as
well. Plus support for MMIO in addition to PIO operation as TURBOchannel
requires it anyway.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index ad92b6a..b79711d 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -2534,7 +2534,7 @@
config FDDI
bool "FDDI driver support"
- depends on (PCI || EISA)
+ depends on (PCI || EISA || TC)
help
Fiber Distributed Data Interface is a high speed local area network
design; essentially a replacement for high speed Ethernet. FDDI can
@@ -2544,11 +2544,31 @@
will say N.
config DEFXX
- tristate "Digital DEFEA and DEFPA adapter support"
- depends on FDDI && (PCI || EISA)
- help
- This is support for the DIGITAL series of EISA (DEFEA) and PCI
- (DEFPA) controllers which can connect you to a local FDDI network.
+ tristate "Digital DEFTA/DEFEA/DEFPA adapter support"
+ depends on FDDI && (PCI || EISA || TC)
+ ---help---
+ This is support for the DIGITAL series of TURBOchannel (DEFTA),
+ EISA (DEFEA) and PCI (DEFPA) controllers which can connect you
+ to a local FDDI network.
+
+ To compile this driver as a module, choose M here: the module
+ will be called defxx. If unsure, say N.
+
+config DEFXX_MMIO
+ bool
+ prompt "Use MMIO instead of PIO" if PCI || EISA
+ depends on DEFXX
+ default n if PCI || EISA
+ default y
+ ---help---
+ This instructs the driver to use EISA or PCI memory-mapped I/O
+ (MMIO) as appropriate instead of programmed I/O ports (PIO).
+ Enabling this gives an improvement in processing time in parts
+ of the driver, but it may cause problems with EISA (DEFEA)
+ adapters. TURBOchannel does not have the concept of I/O ports,
+ so MMIO is always used for these (DEFTA) adapters.
+
+ If unsure, say N.
config SKFP
tristate "SysKonnect FDDI PCI support"
diff --git a/drivers/net/defxx.c b/drivers/net/defxx.c
index dc3ab3b..07d2731 100644
--- a/drivers/net/defxx.c
+++ b/drivers/net/defxx.c
@@ -10,10 +10,12 @@
*
* Abstract:
* A Linux device driver supporting the Digital Equipment Corporation
- * FDDI EISA and PCI controller families. Supported adapters include:
+ * FDDI TURBOchannel, EISA and PCI controller families. Supported
+ * adapters include:
*
- * DEC FDDIcontroller/EISA (DEFEA)
- * DEC FDDIcontroller/PCI (DEFPA)
+ * DEC FDDIcontroller/TURBOchannel (DEFTA)
+ * DEC FDDIcontroller/EISA (DEFEA)
+ * DEC FDDIcontroller/PCI (DEFPA)
*
* The original author:
* LVS Lawrence V. Stefani <lstefani@yahoo.com>
@@ -193,24 +195,27 @@
* 14 Aug 2004 macro Fix device names reported.
* 14 Jun 2005 macro Use irqreturn_t.
* 23 Oct 2006 macro Big-endian host support.
+ * 14 Dec 2006 macro TURBOchannel support.
*/
/* Include files */
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/string.h>
-#include <linux/errno.h>
-#include <linux/ioport.h>
-#include <linux/slab.h>
-#include <linux/interrupt.h>
-#include <linux/pci.h>
-#include <linux/delay.h>
-#include <linux/init.h>
-#include <linux/netdevice.h>
-#include <linux/fddidevice.h>
-#include <linux/skbuff.h>
#include <linux/bitops.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/eisa.h>
+#include <linux/errno.h>
+#include <linux/fddidevice.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/pci.h>
+#include <linux/skbuff.h>
+#include <linux/slab.h>
+#include <linux/string.h>
+#include <linux/tc.h>
#include <asm/byteorder.h>
#include <asm/io.h>
@@ -219,8 +224,8 @@
/* Version information string should be updated prior to each new release! */
#define DRV_NAME "defxx"
-#define DRV_VERSION "v1.09"
-#define DRV_RELDATE "2006/10/23"
+#define DRV_VERSION "v1.10"
+#define DRV_RELDATE "2006/12/14"
static char version[] __devinitdata =
DRV_NAME ": " DRV_VERSION " " DRV_RELDATE
@@ -235,12 +240,41 @@
*/
#define NEW_SKB_SIZE (PI_RCV_DATA_K_SIZE_MAX+128)
+#define __unused __attribute__ ((unused))
+
+#ifdef CONFIG_PCI
+#define DFX_BUS_PCI(dev) (dev->bus == &pci_bus_type)
+#else
+#define DFX_BUS_PCI(dev) 0
+#endif
+
+#ifdef CONFIG_EISA
+#define DFX_BUS_EISA(dev) (dev->bus == &eisa_bus_type)
+#else
+#define DFX_BUS_EISA(dev) 0
+#endif
+
+#ifdef CONFIG_TC
+#define DFX_BUS_TC(dev) (dev->bus == &tc_bus_type)
+#else
+#define DFX_BUS_TC(dev) 0
+#endif
+
+#ifdef CONFIG_DEFXX_MMIO
+#define DFX_MMIO 1
+#else
+#define DFX_MMIO 0
+#endif
+
/* Define module-wide (static) routines */
static void dfx_bus_init(struct net_device *dev);
+static void dfx_bus_uninit(struct net_device *dev);
static void dfx_bus_config_check(DFX_board_t *bp);
-static int dfx_driver_init(struct net_device *dev, const char *print_name);
+static int dfx_driver_init(struct net_device *dev,
+ const char *print_name,
+ resource_size_t bar_start);
static int dfx_adap_init(DFX_board_t *bp, int get_buffers);
static int dfx_open(struct net_device *dev);
@@ -273,13 +307,13 @@
/* Define module-wide (static) variables */
-static struct net_device *root_dfx_eisa_dev;
+static struct pci_driver dfx_pci_driver;
+static struct eisa_driver dfx_eisa_driver;
+static struct tc_driver dfx_tc_driver;
/*
* =======================
- * = dfx_port_write_byte =
- * = dfx_port_read_byte =
* = dfx_port_write_long =
* = dfx_port_read_long =
* =======================
@@ -291,12 +325,11 @@
* None
*
* Arguments:
- * bp - pointer to board information
- * offset - register offset from base I/O address
- * data - for dfx_port_write_byte and dfx_port_write_long, this
- * is a value to write.
- * for dfx_port_read_byte and dfx_port_read_byte, this
- * is a pointer to store the read value.
+ * bp - pointer to board information
+ * offset - register offset from base I/O address
+ * data - for dfx_port_write_long, this is a value to write;
+ * for dfx_port_read_long, this is a pointer to store
+ * the read value
*
* Functional Description:
* These routines perform the correct operation to read or write
@@ -310,7 +343,7 @@
* registers using the register offsets defined in DEFXX.H.
*
* PCI port block base addresses are assigned by the PCI BIOS or system
- * firmware. There is one 128 byte port block which can be accessed. It
+ * firmware. There is one 128 byte port block which can be accessed. It
* allows for I/O mapping of both PDQ and PFI registers using the register
* offsets defined in DEFXX.H.
*
@@ -318,7 +351,7 @@
* None
*
* Assumptions:
- * bp->base_addr is a valid base I/O address for this adapter.
+ * bp->base is a valid base I/O address for this adapter.
* offset is a valid register offset for this adapter.
*
* Side Effects:
@@ -329,69 +362,135 @@
* advantage of strict data type checking.
*/
-static inline void dfx_port_write_byte(
- DFX_board_t *bp,
- int offset,
- u8 data
- )
+static inline void dfx_writel(DFX_board_t *bp, int offset, u32 data)
+{
+ writel(data, bp->base.mem + offset);
+ mb();
+}
- {
- u16 port = bp->base_addr + offset;
+static inline void dfx_outl(DFX_board_t *bp, int offset, u32 data)
+{
+ outl(data, bp->base.port + offset);
+}
- outb(data, port);
- }
+static void dfx_port_write_long(DFX_board_t *bp, int offset, u32 data)
+{
+ struct device __unused *bdev = bp->bus_dev;
+ int dfx_bus_tc = DFX_BUS_TC(bdev);
+ int dfx_use_mmio = DFX_MMIO || dfx_bus_tc;
-static inline void dfx_port_read_byte(
- DFX_board_t *bp,
- int offset,
- u8 *data
- )
+ if (dfx_use_mmio)
+ dfx_writel(bp, offset, data);
+ else
+ dfx_outl(bp, offset, data);
+}
- {
- u16 port = bp->base_addr + offset;
- *data = inb(port);
- }
+static inline void dfx_readl(DFX_board_t *bp, int offset, u32 *data)
+{
+ mb();
+ *data = readl(bp->base.mem + offset);
+}
-static inline void dfx_port_write_long(
- DFX_board_t *bp,
- int offset,
- u32 data
- )
+static inline void dfx_inl(DFX_board_t *bp, int offset, u32 *data)
+{
+ *data = inl(bp->base.port + offset);
+}
- {
- u16 port = bp->base_addr + offset;
+static void dfx_port_read_long(DFX_board_t *bp, int offset, u32 *data)
+{
+ struct device __unused *bdev = bp->bus_dev;
+ int dfx_bus_tc = DFX_BUS_TC(bdev);
+ int dfx_use_mmio = DFX_MMIO || dfx_bus_tc;
- outl(data, port);
- }
-
-static inline void dfx_port_read_long(
- DFX_board_t *bp,
- int offset,
- u32 *data
- )
-
- {
- u16 port = bp->base_addr + offset;
-
- *data = inl(port);
- }
+ if (dfx_use_mmio)
+ dfx_readl(bp, offset, data);
+ else
+ dfx_inl(bp, offset, data);
+}
/*
- * =============
- * = dfx_init_one_pci_or_eisa =
- * =============
+ * ================
+ * = dfx_get_bars =
+ * ================
*
* Overview:
- * Initializes a supported FDDI EISA or PCI controller
+ * Retrieves the address range used to access control and status
+ * registers.
+ *
+ * Returns:
+ * None
+ *
+ * Arguments:
+ * bdev - pointer to device information
+ * bar_start - pointer to store the start address
+ * bar_len - pointer to store the length of the area
+ *
+ * Assumptions:
+ * I am sure there are some.
+ *
+ * Side Effects:
+ * None
+ */
+static void dfx_get_bars(struct device *bdev,
+ resource_size_t *bar_start, resource_size_t *bar_len)
+{
+ int dfx_bus_pci = DFX_BUS_PCI(bdev);
+ int dfx_bus_eisa = DFX_BUS_EISA(bdev);
+ int dfx_bus_tc = DFX_BUS_TC(bdev);
+ int dfx_use_mmio = DFX_MMIO || dfx_bus_tc;
+
+ if (dfx_bus_pci) {
+ int num = dfx_use_mmio ? 0 : 1;
+
+ *bar_start = pci_resource_start(to_pci_dev(bdev), num);
+ *bar_len = pci_resource_len(to_pci_dev(bdev), num);
+ }
+ if (dfx_bus_eisa) {
+ unsigned long base_addr = to_eisa_device(bdev)->base_addr;
+ resource_size_t bar;
+
+ if (dfx_use_mmio) {
+ bar = inb(base_addr + PI_ESIC_K_MEM_ADD_CMP_2);
+ bar <<= 8;
+ bar |= inb(base_addr + PI_ESIC_K_MEM_ADD_CMP_1);
+ bar <<= 8;
+ bar |= inb(base_addr + PI_ESIC_K_MEM_ADD_CMP_0);
+ bar <<= 16;
+ *bar_start = bar;
+ bar = inb(base_addr + PI_ESIC_K_MEM_ADD_MASK_2);
+ bar <<= 8;
+ bar |= inb(base_addr + PI_ESIC_K_MEM_ADD_MASK_1);
+ bar <<= 8;
+ bar |= inb(base_addr + PI_ESIC_K_MEM_ADD_MASK_0);
+ bar <<= 16;
+ *bar_len = (bar | PI_MEM_ADD_MASK_M) + 1;
+ } else {
+ *bar_start = base_addr;
+ *bar_len = PI_ESIC_K_CSR_IO_LEN;
+ }
+ }
+ if (dfx_bus_tc) {
+ *bar_start = to_tc_dev(bdev)->resource.start +
+ PI_TC_K_CSR_OFFSET;
+ *bar_len = PI_TC_K_CSR_LEN;
+ }
+}
+
+/*
+ * ================
+ * = dfx_register =
+ * ================
+ *
+ * Overview:
+ * Initializes a supported FDDI controller
*
* Returns:
* Condition code
*
* Arguments:
- * pdev - pointer to pci device information (NULL for EISA)
- * ioaddr - pointer to port (NULL for PCI)
+ * bdev - pointer to device information
*
* Functional Description:
*
@@ -407,56 +506,74 @@
* initialized and the board resources are read and stored in
* the device structure.
*/
-static int __devinit dfx_init_one_pci_or_eisa(struct pci_dev *pdev, long ioaddr)
+static int __devinit dfx_register(struct device *bdev)
{
static int version_disp;
- char *print_name = DRV_NAME;
+ int dfx_bus_pci = DFX_BUS_PCI(bdev);
+ int dfx_bus_tc = DFX_BUS_TC(bdev);
+ int dfx_use_mmio = DFX_MMIO || dfx_bus_tc;
+ char *print_name = bdev->bus_id;
struct net_device *dev;
DFX_board_t *bp; /* board pointer */
+ resource_size_t bar_start = 0; /* pointer to port */
+ resource_size_t bar_len = 0; /* resource length */
int alloc_size; /* total buffer size used */
- int err;
+ struct resource *region;
+ int err = 0;
if (!version_disp) { /* display version info if adapter is found */
version_disp = 1; /* set display flag to TRUE so that */
printk(version); /* we only display this string ONCE */
}
- if (pdev != NULL)
- print_name = pci_name(pdev);
-
dev = alloc_fddidev(sizeof(*bp));
if (!dev) {
- printk(KERN_ERR "%s: unable to allocate fddidev, aborting\n",
+ printk(KERN_ERR "%s: Unable to allocate fddidev, aborting\n",
print_name);
return -ENOMEM;
}
/* Enable PCI device. */
- if (pdev != NULL) {
- err = pci_enable_device (pdev);
- if (err) goto err_out;
- ioaddr = pci_resource_start (pdev, 1);
- }
-
- SET_MODULE_OWNER(dev);
- if (pdev != NULL)
- SET_NETDEV_DEV(dev, &pdev->dev);
-
- bp = dev->priv;
-
- if (!request_region(ioaddr,
- pdev ? PFI_K_CSR_IO_LEN : PI_ESIC_K_CSR_IO_LEN,
- print_name)) {
- printk(KERN_ERR "%s: Cannot reserve I/O resource "
- "0x%x @ 0x%lx, aborting\n", print_name,
- pdev ? PFI_K_CSR_IO_LEN : PI_ESIC_K_CSR_IO_LEN, ioaddr);
- err = -EBUSY;
+ if (dfx_bus_pci && pci_enable_device(to_pci_dev(bdev))) {
+ printk(KERN_ERR "%s: Cannot enable PCI device, aborting\n",
+ print_name);
goto err_out;
}
- /* Initialize new device structure */
+ SET_MODULE_OWNER(dev);
+ SET_NETDEV_DEV(dev, bdev);
- dev->base_addr = ioaddr; /* save port (I/O) base address */
+ bp = netdev_priv(dev);
+ bp->bus_dev = bdev;
+ dev_set_drvdata(bdev, dev);
+
+ dfx_get_bars(bdev, &bar_start, &bar_len);
+
+ if (dfx_use_mmio)
+ region = request_mem_region(bar_start, bar_len, print_name);
+ else
+ region = request_region(bar_start, bar_len, print_name);
+ if (!region) {
+ printk(KERN_ERR "%s: Cannot reserve I/O resource "
+ "0x%lx @ 0x%lx, aborting\n",
+ print_name, (long)bar_len, (long)bar_start);
+ err = -EBUSY;
+ goto err_out_disable;
+ }
+
+ /* Set up I/O base address. */
+ if (dfx_use_mmio) {
+ bp->base.mem = ioremap_nocache(bar_start, bar_len);
+ if (!bp->base.mem) {
+ printk(KERN_ERR "%s: Cannot map MMIO\n", print_name);
+ goto err_out_region;
+ }
+ } else {
+ bp->base.port = bar_start;
+ dev->base_addr = bar_start;
+ }
+
+ /* Initialize new device structure */
dev->get_stats = dfx_ctl_get_stats;
dev->open = dfx_open;
@@ -465,22 +582,12 @@
dev->set_multicast_list = dfx_ctl_set_multicast_list;
dev->set_mac_address = dfx_ctl_set_mac_address;
- if (pdev == NULL) {
- /* EISA board */
- bp->bus_type = DFX_BUS_TYPE_EISA;
- bp->next = root_dfx_eisa_dev;
- root_dfx_eisa_dev = dev;
- } else {
- /* PCI board */
- bp->bus_type = DFX_BUS_TYPE_PCI;
- bp->pci_dev = pdev;
- pci_set_drvdata (pdev, dev);
- pci_set_master (pdev);
- }
+ if (dfx_bus_pci)
+ pci_set_master(to_pci_dev(bdev));
- if (dfx_driver_init(dev, print_name) != DFX_K_SUCCESS) {
+ if (dfx_driver_init(dev, print_name, bar_start) != DFX_K_SUCCESS) {
err = -ENODEV;
- goto err_out_region;
+ goto err_out_unmap;
}
err = register_netdev(dev);
@@ -499,44 +606,28 @@
sizeof(PI_CONSUMER_BLOCK) +
(PI_ALIGN_K_DESC_BLK - 1);
if (bp->kmalloced)
- pci_free_consistent(pdev, alloc_size,
- bp->kmalloced, bp->kmalloced_dma);
+ dma_free_coherent(bdev, alloc_size,
+ bp->kmalloced, bp->kmalloced_dma);
+
+err_out_unmap:
+ if (dfx_use_mmio)
+ iounmap(bp->base.mem);
+
err_out_region:
- release_region(ioaddr, pdev ? PFI_K_CSR_IO_LEN : PI_ESIC_K_CSR_IO_LEN);
+ if (dfx_use_mmio)
+ release_mem_region(bar_start, bar_len);
+ else
+ release_region(bar_start, bar_len);
+
+err_out_disable:
+ if (dfx_bus_pci)
+ pci_disable_device(to_pci_dev(bdev));
+
err_out:
free_netdev(dev);
return err;
}
-static int __devinit dfx_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
-{
- return dfx_init_one_pci_or_eisa(pdev, 0);
-}
-
-static int __init dfx_eisa_init(void)
-{
- int rc = -ENODEV;
- int i; /* used in for loops */
- u16 port; /* temporary I/O (port) address */
- u32 slot_id; /* EISA hardware (slot) ID read from adapter */
-
- DBG_printk("In dfx_eisa_init...\n");
-
- /* Scan for FDDI EISA controllers */
-
- for (i=0; i < DFX_MAX_EISA_SLOTS; i++) /* only scan for up to 16 EISA slots */
- {
- port = (i << 12) + PI_ESIC_K_SLOT_ID; /* port = I/O address for reading slot ID */
- slot_id = inl(port); /* read EISA HW (slot) ID */
- if ((slot_id & 0xF0FFFFFF) == DEFEA_PRODUCT_ID)
- {
- port = (i << 12); /* recalc base addr */
-
- if (dfx_init_one_pci_or_eisa(NULL, port) == 0) rc = 0;
- }
- }
- return rc;
-}
/*
* ================
@@ -544,7 +635,7 @@
* ================
*
* Overview:
- * Initializes EISA and PCI controller bus-specific logic.
+ * Initializes the bus-specific controller logic.
*
* Returns:
* None
@@ -560,7 +651,7 @@
* None
*
* Assumptions:
- * dev->base_addr has already been set with the proper
+ * bp->base has already been set with the proper
* base I/O address for this device.
*
* Side Effects:
@@ -571,87 +662,103 @@
static void __devinit dfx_bus_init(struct net_device *dev)
{
- DFX_board_t *bp = dev->priv;
- u8 val; /* used for I/O read/writes */
+ DFX_board_t *bp = netdev_priv(dev);
+ struct device *bdev = bp->bus_dev;
+ int dfx_bus_pci = DFX_BUS_PCI(bdev);
+ int dfx_bus_eisa = DFX_BUS_EISA(bdev);
+ int dfx_bus_tc = DFX_BUS_TC(bdev);
+ int dfx_use_mmio = DFX_MMIO || dfx_bus_tc;
+ u8 val;
DBG_printk("In dfx_bus_init...\n");
- /*
- * Initialize base I/O address field in bp structure
- *
- * Note: bp->base_addr is the same as dev->base_addr.
- * It's useful because often we'll need to read
- * or write registers where we already have the
- * bp pointer instead of the dev pointer. Having
- * the base address in the bp structure will
- * save a pointer dereference.
- *
- * IMPORTANT!! This field must be defined before
- * any of the dfx_port_* inline functions are
- * called.
- */
-
- bp->base_addr = dev->base_addr;
-
- /* And a pointer back to the net_device struct */
+ /* Initialize a pointer back to the net_device struct */
bp->dev = dev;
/* Initialize adapter based on bus type */
- if (bp->bus_type == DFX_BUS_TYPE_EISA)
- {
- /* Get the interrupt level from the ESIC chip */
+ if (dfx_bus_tc)
+ dev->irq = to_tc_dev(bdev)->interrupt;
+ if (dfx_bus_eisa) {
+ unsigned long base_addr = to_eisa_device(bdev)->base_addr;
- dfx_port_read_byte(bp, PI_ESIC_K_IO_CONFIG_STAT_0, &val);
- switch ((val & PI_CONFIG_STAT_0_M_IRQ) >> PI_CONFIG_STAT_0_V_IRQ)
- {
- case PI_CONFIG_STAT_0_IRQ_K_9:
- dev->irq = 9;
- break;
+ /* Get the interrupt level from the ESIC chip. */
+ val = inb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0);
+ val &= PI_CONFIG_STAT_0_M_IRQ;
+ val >>= PI_CONFIG_STAT_0_V_IRQ;
- case PI_CONFIG_STAT_0_IRQ_K_10:
- dev->irq = 10;
- break;
+ switch (val) {
+ case PI_CONFIG_STAT_0_IRQ_K_9:
+ dev->irq = 9;
+ break;
- case PI_CONFIG_STAT_0_IRQ_K_11:
- dev->irq = 11;
- break;
+ case PI_CONFIG_STAT_0_IRQ_K_10:
+ dev->irq = 10;
+ break;
- case PI_CONFIG_STAT_0_IRQ_K_15:
- dev->irq = 15;
- break;
- }
+ case PI_CONFIG_STAT_0_IRQ_K_11:
+ dev->irq = 11;
+ break;
- /* Enable access to I/O on the board by writing 0x03 to Function Control Register */
-
- dfx_port_write_byte(bp, PI_ESIC_K_FUNCTION_CNTRL, PI_ESIC_K_FUNCTION_CNTRL_IO_ENB);
-
- /* Set the I/O decode range of the board */
-
- val = ((dev->base_addr >> 12) << PI_IO_CMP_V_SLOT);
- dfx_port_write_byte(bp, PI_ESIC_K_IO_CMP_0_1, val);
- dfx_port_write_byte(bp, PI_ESIC_K_IO_CMP_1_1, val);
-
- /* Enable access to rest of module (including PDQ and packet memory) */
-
- dfx_port_write_byte(bp, PI_ESIC_K_SLOT_CNTRL, PI_SLOT_CNTRL_M_ENB);
+ case PI_CONFIG_STAT_0_IRQ_K_15:
+ dev->irq = 15;
+ break;
+ }
/*
- * Map PDQ registers into I/O space. This is done by clearing a bit
- * in Burst Holdoff register.
+ * Enable memory decoding (MEMCS0) and/or port decoding
+ * (IOCS1/IOCS0) as appropriate in Function Control
+ * Register. One of the port chip selects seems to be
+ * used for the Burst Holdoff register, but this bit of
+ * documentation is missing and as yet it has not been
+ * determined which of the two. This is also the reason
+ * the size of the decoded port range is twice as large
+ * as one required by the PDQ.
*/
- dfx_port_read_byte(bp, PI_ESIC_K_BURST_HOLDOFF, &val);
- dfx_port_write_byte(bp, PI_ESIC_K_BURST_HOLDOFF, (val & ~PI_BURST_HOLDOFF_M_MEM_MAP));
+ /* Set the decode range of the board. */
+ val = ((bp->base.port >> 12) << PI_IO_CMP_V_SLOT);
+ outb(base_addr + PI_ESIC_K_IO_ADD_CMP_0_1, val);
+ outb(base_addr + PI_ESIC_K_IO_ADD_CMP_0_0, 0);
+ outb(base_addr + PI_ESIC_K_IO_ADD_CMP_1_1, val);
+ outb(base_addr + PI_ESIC_K_IO_ADD_CMP_1_0, 0);
+ val = PI_ESIC_K_CSR_IO_LEN - 1;
+ outb(base_addr + PI_ESIC_K_IO_ADD_MASK_0_1, (val >> 8) & 0xff);
+ outb(base_addr + PI_ESIC_K_IO_ADD_MASK_0_0, val & 0xff);
+ outb(base_addr + PI_ESIC_K_IO_ADD_MASK_1_1, (val >> 8) & 0xff);
+ outb(base_addr + PI_ESIC_K_IO_ADD_MASK_1_0, val & 0xff);
+
+ /* Enable the decoders. */
+ val = PI_FUNCTION_CNTRL_M_IOCS1 | PI_FUNCTION_CNTRL_M_IOCS0;
+ if (dfx_use_mmio)
+ val |= PI_FUNCTION_CNTRL_M_MEMCS0;
+ outb(base_addr + PI_ESIC_K_FUNCTION_CNTRL, val);
+
+ /*
+ * Enable access to the rest of the module
+ * (including PDQ and packet memory).
+ */
+ val = PI_SLOT_CNTRL_M_ENB;
+ outb(base_addr + PI_ESIC_K_SLOT_CNTRL, val);
+
+ /*
+ * Map PDQ registers into memory or port space. This is
+ * done with a bit in the Burst Holdoff register.
+ */
+ val = inb(base_addr + PI_DEFEA_K_BURST_HOLDOFF);
+ if (dfx_use_mmio)
+ val |= PI_BURST_HOLDOFF_V_MEM_MAP;
+ else
+ val &= ~PI_BURST_HOLDOFF_V_MEM_MAP;
+ outb(base_addr + PI_DEFEA_K_BURST_HOLDOFF, val);
/* Enable interrupts at EISA bus interface chip (ESIC) */
-
- dfx_port_read_byte(bp, PI_ESIC_K_IO_CONFIG_STAT_0, &val);
- dfx_port_write_byte(bp, PI_ESIC_K_IO_CONFIG_STAT_0, (val | PI_CONFIG_STAT_0_M_INT_ENB));
- }
- else
- {
- struct pci_dev *pdev = bp->pci_dev;
+ val = inb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0);
+ val |= PI_CONFIG_STAT_0_M_INT_ENB;
+ outb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0, val);
+ }
+ if (dfx_bus_pci) {
+ struct pci_dev *pdev = to_pci_dev(bdev);
/* Get the interrupt level from the PCI Configuration Table */
@@ -660,17 +767,70 @@
/* Check Latency Timer and set if less than minimal */
pci_read_config_byte(pdev, PCI_LATENCY_TIMER, &val);
- if (val < PFI_K_LAT_TIMER_MIN) /* if less than min, override with default */
- {
+ if (val < PFI_K_LAT_TIMER_MIN) {
val = PFI_K_LAT_TIMER_DEF;
pci_write_config_byte(pdev, PCI_LATENCY_TIMER, val);
- }
+ }
/* Enable interrupts at PCI bus interface chip (PFI) */
-
- dfx_port_write_long(bp, PFI_K_REG_MODE_CTRL, (PFI_MODE_M_PDQ_INT_ENB | PFI_MODE_M_DMA_ENB));
- }
+ val = PFI_MODE_M_PDQ_INT_ENB | PFI_MODE_M_DMA_ENB;
+ dfx_port_write_long(bp, PFI_K_REG_MODE_CTRL, val);
}
+}
+
+/*
+ * ==================
+ * = dfx_bus_uninit =
+ * ==================
+ *
+ * Overview:
+ * Uninitializes the bus-specific controller logic.
+ *
+ * Returns:
+ * None
+ *
+ * Arguments:
+ * dev - pointer to device information
+ *
+ * Functional Description:
+ * Perform bus-specific logic uninitialization.
+ *
+ * Return Codes:
+ * None
+ *
+ * Assumptions:
+ * bp->base has already been set with the proper
+ * base I/O address for this device.
+ *
+ * Side Effects:
+ * Interrupts are disabled at the adapter bus-specific logic.
+ */
+
+static void __devinit dfx_bus_uninit(struct net_device *dev)
+{
+ DFX_board_t *bp = netdev_priv(dev);
+ struct device *bdev = bp->bus_dev;
+ int dfx_bus_pci = DFX_BUS_PCI(bdev);
+ int dfx_bus_eisa = DFX_BUS_EISA(bdev);
+ u8 val;
+
+ DBG_printk("In dfx_bus_uninit...\n");
+
+ /* Uninitialize adapter based on bus type */
+
+ if (dfx_bus_eisa) {
+ unsigned long base_addr = to_eisa_device(bdev)->base_addr;
+
+ /* Disable interrupts at EISA bus interface chip (ESIC) */
+ val = inb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0);
+ val &= ~PI_CONFIG_STAT_0_M_INT_ENB;
+ outb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0, val);
+ }
+ if (dfx_bus_pci) {
+ /* Disable interrupts at PCI bus interface chip (PFI) */
+ dfx_port_write_long(bp, PFI_K_REG_MODE_CTRL, 0);
+ }
+}
/*
@@ -705,18 +865,16 @@
static void __devinit dfx_bus_config_check(DFX_board_t *bp)
{
+ struct device __unused *bdev = bp->bus_dev;
+ int dfx_bus_eisa = DFX_BUS_EISA(bdev);
int status; /* return code from adapter port control call */
- u32 slot_id; /* EISA-bus hardware id (DEC3001, DEC3002,...) */
u32 host_data; /* LW data returned from port control call */
DBG_printk("In dfx_bus_config_check...\n");
/* Configuration check only valid for EISA adapter */
- if (bp->bus_type == DFX_BUS_TYPE_EISA)
- {
- dfx_port_read_long(bp, PI_ESIC_K_SLOT_ID, &slot_id);
-
+ if (dfx_bus_eisa) {
/*
* First check if revision 2 EISA controller. Rev. 1 cards used
* PDQ revision B, so no workaround needed in this case. Rev. 3
@@ -724,14 +882,11 @@
* case, either. Only Rev. 2 cards used either Rev. D or E
* chips, so we must verify the chip revision on Rev. 2 cards.
*/
-
- if (slot_id == DEFEA_PROD_ID_2)
- {
+ if (to_eisa_device(bdev)->id.driver_data == DEFEA_PROD_ID_2) {
/*
- * Revision 2 FDDI EISA controller found, so let's check PDQ
- * revision of adapter.
+ * Revision 2 FDDI EISA controller found,
+ * so let's check PDQ revision of adapter.
*/
-
status = dfx_hw_port_ctrl_req(bp,
PI_PCTRL_M_SUB_CMD,
PI_SUB_CMD_K_PDQ_REV_GET,
@@ -805,13 +960,20 @@
*/
static int __devinit dfx_driver_init(struct net_device *dev,
- const char *print_name)
+ const char *print_name,
+ resource_size_t bar_start)
{
- DFX_board_t *bp = dev->priv;
- int alloc_size; /* total buffer size needed */
- char *top_v, *curr_v; /* virtual addrs into memory block */
- dma_addr_t top_p, curr_p; /* physical addrs into memory block */
- u32 data; /* host data register value */
+ DFX_board_t *bp = netdev_priv(dev);
+ struct device *bdev = bp->bus_dev;
+ int dfx_bus_pci = DFX_BUS_PCI(bdev);
+ int dfx_bus_eisa = DFX_BUS_EISA(bdev);
+ int dfx_bus_tc = DFX_BUS_TC(bdev);
+ int dfx_use_mmio = DFX_MMIO || dfx_bus_tc;
+ int alloc_size; /* total buffer size needed */
+ char *top_v, *curr_v; /* virtual addrs into memory block */
+ dma_addr_t top_p, curr_p; /* physical addrs into memory block */
+ u32 data, le32; /* host data register value */
+ char *board_name = NULL;
DBG_printk("In dfx_driver_init...\n");
@@ -860,8 +1022,8 @@
print_name);
return(DFX_K_FAILURE);
}
- data = cpu_to_le32(data);
- memcpy(&bp->factory_mac_addr[0], &data, sizeof(u32));
+ le32 = cpu_to_le32(data);
+ memcpy(&bp->factory_mac_addr[0], &le32, sizeof(u32));
if (dfx_hw_port_ctrl_req(bp, PI_PCTRL_M_MLA, PI_PDATA_A_MLA_K_HI, 0,
&data) != DFX_K_SUCCESS) {
@@ -869,8 +1031,8 @@
print_name);
return(DFX_K_FAILURE);
}
- data = cpu_to_le32(data);
- memcpy(&bp->factory_mac_addr[4], &data, sizeof(u16));
+ le32 = cpu_to_le32(data);
+ memcpy(&bp->factory_mac_addr[4], &le32, sizeof(u16));
/*
* Set current address to factory address
@@ -880,20 +1042,18 @@
*/
memcpy(dev->dev_addr, bp->factory_mac_addr, FDDI_K_ALEN);
- if (bp->bus_type == DFX_BUS_TYPE_EISA)
- printk("%s: DEFEA at I/O addr = 0x%lX, IRQ = %d, "
- "Hardware addr = %02X-%02X-%02X-%02X-%02X-%02X\n",
- print_name, dev->base_addr, dev->irq,
- dev->dev_addr[0], dev->dev_addr[1],
- dev->dev_addr[2], dev->dev_addr[3],
- dev->dev_addr[4], dev->dev_addr[5]);
- else
- printk("%s: DEFPA at I/O addr = 0x%lX, IRQ = %d, "
- "Hardware addr = %02X-%02X-%02X-%02X-%02X-%02X\n",
- print_name, dev->base_addr, dev->irq,
- dev->dev_addr[0], dev->dev_addr[1],
- dev->dev_addr[2], dev->dev_addr[3],
- dev->dev_addr[4], dev->dev_addr[5]);
+ if (dfx_bus_tc)
+ board_name = "DEFTA";
+ if (dfx_bus_eisa)
+ board_name = "DEFEA";
+ if (dfx_bus_pci)
+ board_name = "DEFPA";
+ pr_info("%s: %s at %saddr = 0x%llx, IRQ = %d, "
+ "Hardware addr = %02X-%02X-%02X-%02X-%02X-%02X\n",
+ print_name, board_name, dfx_use_mmio ? "" : "I/O ",
+ (long long)bar_start, dev->irq,
+ dev->dev_addr[0], dev->dev_addr[1], dev->dev_addr[2],
+ dev->dev_addr[3], dev->dev_addr[4], dev->dev_addr[5]);
/*
* Get memory for descriptor block, consumer block, and other buffers
@@ -908,8 +1068,9 @@
#endif
sizeof(PI_CONSUMER_BLOCK) +
(PI_ALIGN_K_DESC_BLK - 1);
- bp->kmalloced = top_v = pci_alloc_consistent(bp->pci_dev, alloc_size,
- &bp->kmalloced_dma);
+ bp->kmalloced = top_v = dma_alloc_coherent(bp->bus_dev, alloc_size,
+ &bp->kmalloced_dma,
+ GFP_ATOMIC);
if (top_v == NULL) {
printk("%s: Could not allocate memory for host buffers "
"and structures!\n", print_name);
@@ -1219,14 +1380,15 @@
static int dfx_open(struct net_device *dev)
{
+ DFX_board_t *bp = netdev_priv(dev);
int ret;
- DFX_board_t *bp = dev->priv;
DBG_printk("In dfx_open...\n");
/* Register IRQ - support shared interrupts by passing device ptr */
- ret = request_irq(dev->irq, dfx_interrupt, IRQF_SHARED, dev->name, dev);
+ ret = request_irq(dev->irq, dfx_interrupt, IRQF_SHARED, dev->name,
+ dev);
if (ret) {
printk(KERN_ERR "%s: Requested IRQ %d is busy\n", dev->name, dev->irq);
return ret;
@@ -1309,7 +1471,7 @@
static int dfx_close(struct net_device *dev)
{
- DFX_board_t *bp = dev->priv;
+ DFX_board_t *bp = netdev_priv(dev);
DBG_printk("In dfx_close...\n");
@@ -1645,7 +1807,7 @@
static void dfx_int_common(struct net_device *dev)
{
- DFX_board_t *bp = dev->priv;
+ DFX_board_t *bp = netdev_priv(dev);
PI_UINT32 port_status; /* Port Status register */
/* Process xmt interrupts - frequent case, so always call this routine */
@@ -1715,18 +1877,16 @@
static irqreturn_t dfx_interrupt(int irq, void *dev_id)
{
- struct net_device *dev = dev_id;
- DFX_board_t *bp; /* private board structure pointer */
-
- /* Get board pointer only if device structure is valid */
-
- bp = dev->priv;
-
- /* See if we're already servicing an interrupt */
+ struct net_device *dev = dev_id;
+ DFX_board_t *bp = netdev_priv(dev);
+ struct device *bdev = bp->bus_dev;
+ int dfx_bus_pci = DFX_BUS_PCI(bdev);
+ int dfx_bus_eisa = DFX_BUS_EISA(bdev);
+ int dfx_bus_tc = DFX_BUS_TC(bdev);
/* Service adapter interrupts */
- if (bp->bus_type == DFX_BUS_TYPE_PCI) {
+ if (dfx_bus_pci) {
u32 status;
dfx_port_read_long(bp, PFI_K_REG_STATUS, &status);
@@ -1750,10 +1910,12 @@
PFI_MODE_M_DMA_ENB));
spin_unlock(&bp->lock);
- } else {
+ }
+ if (dfx_bus_eisa) {
+ unsigned long base_addr = to_eisa_device(bdev)->base_addr;
u8 status;
- dfx_port_read_byte(bp, PI_ESIC_K_IO_CONFIG_STAT_0, &status);
+ status = inb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0);
if (!(status & PI_CONFIG_STAT_0_M_PEND))
return IRQ_NONE;
@@ -1761,15 +1923,35 @@
/* Disable interrupts at the ESIC */
status &= ~PI_CONFIG_STAT_0_M_INT_ENB;
- dfx_port_write_byte(bp, PI_ESIC_K_IO_CONFIG_STAT_0, status);
+ outb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0, status);
/* Call interrupt service routine for this adapter */
dfx_int_common(dev);
/* Reenable interrupts at the ESIC */
- dfx_port_read_byte(bp, PI_ESIC_K_IO_CONFIG_STAT_0, &status);
+ status = inb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0);
status |= PI_CONFIG_STAT_0_M_INT_ENB;
- dfx_port_write_byte(bp, PI_ESIC_K_IO_CONFIG_STAT_0, status);
+ outb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0, status);
+
+ spin_unlock(&bp->lock);
+ }
+ if (dfx_bus_tc) {
+ u32 status;
+
+ dfx_port_read_long(bp, PI_PDQ_K_REG_PORT_STATUS, &status);
+ if (!(status & (PI_PSTATUS_M_RCV_DATA_PENDING |
+ PI_PSTATUS_M_XMT_DATA_PENDING |
+ PI_PSTATUS_M_SMT_HOST_PENDING |
+ PI_PSTATUS_M_UNSOL_PENDING |
+ PI_PSTATUS_M_CMD_RSP_PENDING |
+ PI_PSTATUS_M_CMD_REQ_PENDING |
+ PI_PSTATUS_M_TYPE_0_PENDING)))
+ return IRQ_NONE;
+
+ spin_lock(&bp->lock);
+
+ /* Call interrupt service routine for this adapter */
+ dfx_int_common(dev);
spin_unlock(&bp->lock);
}
@@ -1823,7 +2005,7 @@
static struct net_device_stats *dfx_ctl_get_stats(struct net_device *dev)
{
- DFX_board_t *bp = dev->priv;
+ DFX_board_t *bp = netdev_priv(dev);
/* Fill the bp->stats structure with driver-maintained counters */
@@ -2009,8 +2191,8 @@
*/
static void dfx_ctl_set_multicast_list(struct net_device *dev)
- {
- DFX_board_t *bp = dev->priv;
+{
+ DFX_board_t *bp = netdev_priv(dev);
int i; /* used as index in for loop */
struct dev_mc_list *dmi; /* ptr to multicast addr entry */
@@ -2124,8 +2306,8 @@
static int dfx_ctl_set_mac_address(struct net_device *dev, void *addr)
{
- DFX_board_t *bp = dev->priv;
struct sockaddr *p_sockaddr = (struct sockaddr *)addr;
+ DFX_board_t *bp = netdev_priv(dev);
/* Copy unicast address to driver-maintained structs and update count */
@@ -2764,9 +2946,9 @@
my_skb_align(newskb, 128);
bp->descr_block_virt->rcv_data[i + j].long_1 =
- (u32)pci_map_single(bp->pci_dev, newskb->data,
+ (u32)dma_map_single(bp->bus_dev, newskb->data,
NEW_SKB_SIZE,
- PCI_DMA_FROMDEVICE);
+ DMA_FROM_DEVICE);
/*
* p_rcv_buff_va is only used inside the
* kernel so we put the skb pointer here.
@@ -2880,17 +3062,17 @@
my_skb_align(newskb, 128);
skb = (struct sk_buff *)bp->p_rcv_buff_va[entry];
- pci_unmap_single(bp->pci_dev,
+ dma_unmap_single(bp->bus_dev,
bp->descr_block_virt->rcv_data[entry].long_1,
NEW_SKB_SIZE,
- PCI_DMA_FROMDEVICE);
+ DMA_FROM_DEVICE);
skb_reserve(skb, RCV_BUFF_K_PADDING);
bp->p_rcv_buff_va[entry] = (char *)newskb;
bp->descr_block_virt->rcv_data[entry].long_1 =
- (u32)pci_map_single(bp->pci_dev,
+ (u32)dma_map_single(bp->bus_dev,
newskb->data,
NEW_SKB_SIZE,
- PCI_DMA_FROMDEVICE);
+ DMA_FROM_DEVICE);
} else
skb = NULL;
} else
@@ -3010,7 +3192,7 @@
)
{
- DFX_board_t *bp = dev->priv;
+ DFX_board_t *bp = netdev_priv(dev);
u8 prod; /* local transmit producer index */
PI_XMT_DESCR *p_xmt_descr; /* ptr to transmit descriptor block entry */
XMT_DRIVER_DESCR *p_xmt_drv_descr; /* ptr to transmit driver descriptor */
@@ -3116,8 +3298,8 @@
*/
p_xmt_descr->long_0 = (u32) (PI_XMT_DESCR_M_SOP | PI_XMT_DESCR_M_EOP | ((skb->len) << PI_XMT_DESCR_V_SEG_LEN));
- p_xmt_descr->long_1 = (u32)pci_map_single(bp->pci_dev, skb->data,
- skb->len, PCI_DMA_TODEVICE);
+ p_xmt_descr->long_1 = (u32)dma_map_single(bp->bus_dev, skb->data,
+ skb->len, DMA_TO_DEVICE);
/*
* Verify that descriptor is actually available
@@ -3220,10 +3402,10 @@
/* Return skb to operating system */
comp = bp->rcv_xmt_reg.index.xmt_comp;
- pci_unmap_single(bp->pci_dev,
+ dma_unmap_single(bp->bus_dev,
bp->descr_block_virt->xmt_data[comp].long_1,
p_xmt_drv_descr->p_skb->len,
- PCI_DMA_TODEVICE);
+ DMA_TO_DEVICE);
dev_kfree_skb_irq(p_xmt_drv_descr->p_skb);
/*
@@ -3344,10 +3526,10 @@
/* Return skb to operating system */
comp = bp->rcv_xmt_reg.index.xmt_comp;
- pci_unmap_single(bp->pci_dev,
+ dma_unmap_single(bp->bus_dev,
bp->descr_block_virt->xmt_data[comp].long_1,
p_xmt_drv_descr->p_skb->len,
- PCI_DMA_TODEVICE);
+ DMA_TO_DEVICE);
dev_kfree_skb(p_xmt_drv_descr->p_skb);
/* Increment transmit error counter */
@@ -3375,13 +3557,44 @@
bp->cons_block_virt->xmt_rcv_data = prod_cons;
}
-static void __devexit dfx_remove_one_pci_or_eisa(struct pci_dev *pdev, struct net_device *dev)
+/*
+ * ==================
+ * = dfx_unregister =
+ * ==================
+ *
+ * Overview:
+ * Shuts down an FDDI controller
+ *
+ * Returns:
+ * Condition code
+ *
+ * Arguments:
+ * bdev - pointer to device information
+ *
+ * Functional Description:
+ *
+ * Return Codes:
+ * None
+ *
+ * Assumptions:
+ * It compiles so it should work :-( (PCI cards do :-)
+ *
+ * Side Effects:
+ * Device structures for FDDI adapters (fddi0, fddi1, etc) are
+ * freed.
+ */
+static void __devexit dfx_unregister(struct device *bdev)
{
- DFX_board_t *bp = dev->priv;
+ struct net_device *dev = dev_get_drvdata(bdev);
+ DFX_board_t *bp = netdev_priv(dev);
+ int dfx_bus_pci = DFX_BUS_PCI(bdev);
+ int dfx_bus_tc = DFX_BUS_TC(bdev);
+ int dfx_use_mmio = DFX_MMIO || dfx_bus_tc;
+ resource_size_t bar_start = 0; /* pointer to port */
+ resource_size_t bar_len = 0; /* resource length */
int alloc_size; /* total buffer size used */
unregister_netdev(dev);
- release_region(dev->base_addr, pdev ? PFI_K_CSR_IO_LEN : PI_ESIC_K_CSR_IO_LEN );
alloc_size = sizeof(PI_DESCR_BLOCK) +
PI_CMD_REQ_K_SIZE_MAX + PI_CMD_RSP_K_SIZE_MAX +
@@ -3391,78 +3604,141 @@
sizeof(PI_CONSUMER_BLOCK) +
(PI_ALIGN_K_DESC_BLK - 1);
if (bp->kmalloced)
- pci_free_consistent(pdev, alloc_size, bp->kmalloced,
- bp->kmalloced_dma);
+ dma_free_coherent(bdev, alloc_size,
+ bp->kmalloced, bp->kmalloced_dma);
+
+ dfx_bus_uninit(dev);
+
+ dfx_get_bars(bdev, &bar_start, &bar_len);
+ if (dfx_use_mmio) {
+ iounmap(bp->base.mem);
+ release_mem_region(bar_start, bar_len);
+ } else
+ release_region(bar_start, bar_len);
+
+ if (dfx_bus_pci)
+ pci_disable_device(to_pci_dev(bdev));
+
free_netdev(dev);
}
-static void __devexit dfx_remove_one (struct pci_dev *pdev)
-{
- struct net_device *dev = pci_get_drvdata(pdev);
- dfx_remove_one_pci_or_eisa(pdev, dev);
- pci_set_drvdata(pdev, NULL);
-}
+static int __devinit __unused dfx_dev_register(struct device *);
+static int __devexit __unused dfx_dev_unregister(struct device *);
-static struct pci_device_id dfx_pci_tbl[] = {
- { PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_DEC_FDDI, PCI_ANY_ID, PCI_ANY_ID, },
- { 0, }
+#ifdef CONFIG_PCI
+static int __devinit dfx_pci_register(struct pci_dev *,
+ const struct pci_device_id *);
+static void __devexit dfx_pci_unregister(struct pci_dev *);
+
+static struct pci_device_id dfx_pci_table[] = {
+ { PCI_DEVICE(PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_DEC_FDDI) },
+ { }
};
-MODULE_DEVICE_TABLE(pci, dfx_pci_tbl);
+MODULE_DEVICE_TABLE(pci, dfx_pci_table);
-static struct pci_driver dfx_driver = {
+static struct pci_driver dfx_pci_driver = {
.name = "defxx",
- .probe = dfx_init_one,
- .remove = __devexit_p(dfx_remove_one),
- .id_table = dfx_pci_tbl,
+ .id_table = dfx_pci_table,
+ .probe = dfx_pci_register,
+ .remove = __devexit_p(dfx_pci_unregister),
};
-static int dfx_have_pci;
-static int dfx_have_eisa;
-
-
-static void __exit dfx_eisa_cleanup(void)
+static __devinit int dfx_pci_register(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
{
- struct net_device *dev = root_dfx_eisa_dev;
-
- while (dev)
- {
- struct net_device *tmp;
- DFX_board_t *bp;
-
- bp = (DFX_board_t*)dev->priv;
- tmp = bp->next;
- dfx_remove_one_pci_or_eisa(NULL, dev);
- dev = tmp;
- }
+ return dfx_register(&pdev->dev);
}
-static int __init dfx_init(void)
+static void __devexit dfx_pci_unregister(struct pci_dev *pdev)
{
- int rc_pci, rc_eisa;
+ dfx_unregister(&pdev->dev);
+}
+#endif /* CONFIG_PCI */
- rc_pci = pci_register_driver(&dfx_driver);
- if (rc_pci >= 0) dfx_have_pci = 1;
+#ifdef CONFIG_EISA
+static struct eisa_device_id dfx_eisa_table[] = {
+ { "DEC3001", DEFEA_PROD_ID_1 },
+ { "DEC3002", DEFEA_PROD_ID_2 },
+ { "DEC3003", DEFEA_PROD_ID_3 },
+ { "DEC3004", DEFEA_PROD_ID_4 },
+ { }
+};
+MODULE_DEVICE_TABLE(eisa, dfx_eisa_table);
- rc_eisa = dfx_eisa_init();
- if (rc_eisa >= 0) dfx_have_eisa = 1;
+static struct eisa_driver dfx_eisa_driver = {
+ .id_table = dfx_eisa_table,
+ .driver = {
+ .name = "defxx",
+ .bus = &eisa_bus_type,
+ .probe = dfx_dev_register,
+ .remove = __devexit_p(dfx_dev_unregister),
+ },
+};
+#endif /* CONFIG_EISA */
- return ((rc_eisa < 0) ? 0 : rc_eisa) + ((rc_pci < 0) ? 0 : rc_pci);
+#ifdef CONFIG_TC
+static struct tc_device_id const dfx_tc_table[] = {
+ { "DEC ", "PMAF-FA " },
+ { "DEC ", "PMAF-FD " },
+ { "DEC ", "PMAF-FS " },
+ { "DEC ", "PMAF-FU " },
+ { }
+};
+MODULE_DEVICE_TABLE(tc, dfx_tc_table);
+
+static struct tc_driver dfx_tc_driver = {
+ .id_table = dfx_tc_table,
+ .driver = {
+ .name = "defxx",
+ .bus = &tc_bus_type,
+ .probe = dfx_dev_register,
+ .remove = __devexit_p(dfx_dev_unregister),
+ },
+};
+#endif /* CONFIG_TC */
+
+static int __devinit __unused dfx_dev_register(struct device *dev)
+{
+ int status;
+
+ status = dfx_register(dev);
+ if (!status)
+ get_device(dev);
+ return status;
}
-static void __exit dfx_cleanup(void)
+static int __devexit __unused dfx_dev_unregister(struct device *dev)
{
- if (dfx_have_pci)
- pci_unregister_driver(&dfx_driver);
- if (dfx_have_eisa)
- dfx_eisa_cleanup();
+ put_device(dev);
+ dfx_unregister(dev);
+ return 0;
+}
+
+static int __devinit dfx_init(void)
+{
+ int status;
+
+ status = pci_register_driver(&dfx_pci_driver);
+ if (!status)
+ status = eisa_driver_register(&dfx_eisa_driver);
+ if (!status)
+ status = tc_register_driver(&dfx_tc_driver);
+ return status;
+}
+
+static void __devexit dfx_cleanup(void)
+{
+ tc_unregister_driver(&dfx_tc_driver);
+ eisa_driver_unregister(&dfx_eisa_driver);
+ pci_unregister_driver(&dfx_pci_driver);
}
module_init(dfx_init);
module_exit(dfx_cleanup);
MODULE_AUTHOR("Lawrence V. Stefani");
-MODULE_DESCRIPTION("DEC FDDIcontroller EISA/PCI (DEFEA/DEFPA) driver "
+MODULE_DESCRIPTION("DEC FDDIcontroller TC/EISA/PCI (DEFTA/DEFEA/DEFPA) driver "
DRV_VERSION " " DRV_RELDATE);
MODULE_LICENSE("GPL");
diff --git a/drivers/net/defxx.h b/drivers/net/defxx.h
index 2ce8f97..19a6f64 100644
--- a/drivers/net/defxx.h
+++ b/drivers/net/defxx.h
@@ -26,6 +26,7 @@
* 12-Sep-96 LVS Removed packet request header pointers.
* 04 Aug 2003 macro Converted to the DMA API.
* 23 Oct 2006 macro Big-endian host support.
+ * 14 Dec 2006 macro TURBOchannel support.
*/
#ifndef _DEFXX_H_
@@ -1471,9 +1472,17 @@
#endif /* __BIG_ENDIAN */
+/* Define TC PDQ CSR offset and length */
+
+#define PI_TC_K_CSR_OFFSET 0x100000
+#define PI_TC_K_CSR_LEN 0x40 /* 64 bytes */
+
/* Define EISA controller register offsets */
-#define PI_ESIC_K_BURST_HOLDOFF 0x040
+#define PI_ESIC_K_CSR_IO_LEN 0x80 /* 128 bytes */
+
+#define PI_DEFEA_K_BURST_HOLDOFF 0x040
+
#define PI_ESIC_K_SLOT_ID 0xC80
#define PI_ESIC_K_SLOT_CNTRL 0xC84
#define PI_ESIC_K_MEM_ADD_CMP_0 0xC85
@@ -1488,14 +1497,14 @@
#define PI_ESIC_K_MEM_ADD_LO_CMP_0 0xC8E
#define PI_ESIC_K_MEM_ADD_LO_CMP_1 0xC8F
#define PI_ESIC_K_MEM_ADD_LO_CMP_2 0xC90
-#define PI_ESIC_K_IO_CMP_0_0 0xC91
-#define PI_ESIC_K_IO_CMP_0_1 0xC92
-#define PI_ESIC_K_IO_CMP_1_0 0xC93
-#define PI_ESIC_K_IO_CMP_1_1 0xC94
-#define PI_ESIC_K_IO_CMP_2_0 0xC95
-#define PI_ESIC_K_IO_CMP_2_1 0xC96
-#define PI_ESIC_K_IO_CMP_3_0 0xC97
-#define PI_ESIC_K_IO_CMP_3_1 0xC98
+#define PI_ESIC_K_IO_ADD_CMP_0_0 0xC91
+#define PI_ESIC_K_IO_ADD_CMP_0_1 0xC92
+#define PI_ESIC_K_IO_ADD_CMP_1_0 0xC93
+#define PI_ESIC_K_IO_ADD_CMP_1_1 0xC94
+#define PI_ESIC_K_IO_ADD_CMP_2_0 0xC95
+#define PI_ESIC_K_IO_ADD_CMP_2_1 0xC96
+#define PI_ESIC_K_IO_ADD_CMP_3_0 0xC97
+#define PI_ESIC_K_IO_ADD_CMP_3_1 0xC98
#define PI_ESIC_K_IO_ADD_MASK_0_0 0xC99
#define PI_ESIC_K_IO_ADD_MASK_0_1 0xC9A
#define PI_ESIC_K_IO_ADD_MASK_1_0 0xC9B
@@ -1518,11 +1527,16 @@
#define PI_ESIC_K_INPUT_PORT 0xCAC
#define PI_ESIC_K_OUTPUT_PORT 0xCAD
#define PI_ESIC_K_FUNCTION_CNTRL 0xCAE
-#define PI_ESIC_K_CSR_IO_LEN PI_ESIC_K_FUNCTION_CNTRL+1 /* always last reg + 1 */
-/* Define the value all drivers must write to the function control register. */
+/* Define the bits in the function control register. */
-#define PI_ESIC_K_FUNCTION_CNTRL_IO_ENB 0x03
+#define PI_FUNCTION_CNTRL_M_IOCS0 0x01
+#define PI_FUNCTION_CNTRL_M_IOCS1 0x02
+#define PI_FUNCTION_CNTRL_M_IOCS2 0x04
+#define PI_FUNCTION_CNTRL_M_IOCS3 0x08
+#define PI_FUNCTION_CNTRL_M_MEMCS0 0x10
+#define PI_FUNCTION_CNTRL_M_MEMCS1 0x20
+#define PI_FUNCTION_CNTRL_M_DMA 0x80
/* Define the bits in the slot control register. */
@@ -1540,6 +1554,10 @@
#define PI_BURST_HOLDOFF_V_RESERVED 1
#define PI_BURST_HOLDOFF_V_MEM_MAP 0
+/* Define the implicit mask of the Memory Address Mask Register. */
+
+#define PI_MEM_ADD_MASK_M 0x3ff
+
/*
* Define the fields in the IO Compare registers.
* The driver must initialize the slot field with the slot ID shifted by the
@@ -1577,6 +1595,7 @@
#define DEFEA_PROD_ID_1 0x0130A310 /* DEC product 300, rev 1 */
#define DEFEA_PROD_ID_2 0x0230A310 /* DEC product 300, rev 2 */
#define DEFEA_PROD_ID_3 0x0330A310 /* DEC product 300, rev 3 */
+#define DEFEA_PROD_ID_4 0x0430A310 /* DEC product 300, rev 4 */
/**********************************************/
/* Digital PFI Specification v1.0 Definitions */
@@ -1633,12 +1652,6 @@
#define PFI_STATUS_V_FIFO_EMPTY 1
#define PFI_STATUS_V_DMA_IN_PROGRESS 0
-#define DFX_MAX_EISA_SLOTS 16 /* maximum number of EISA slots to scan */
-#define DFX_MAX_NUM_BOARDS 8 /* maximum number of adapters supported */
-
-#define DFX_BUS_TYPE_PCI 0 /* type code for DEC FDDIcontroller/PCI */
-#define DFX_BUS_TYPE_EISA 1 /* type code for DEC FDDIcontroller/EISA */
-
#define DFX_FC_PRH2_PRH1_PRH0 0x54003820 /* Packet Request Header bytes + FC */
#define DFX_PRH0_BYTE 0x20 /* Packet Request Header byte 0 */
#define DFX_PRH1_BYTE 0x38 /* Packet Request Header byte 1 */
@@ -1756,10 +1769,11 @@
/* Store device, bus-specific, and parameter information for this adapter */
struct net_device *dev; /* pointer to device structure */
- struct net_device *next;
- u32 bus_type; /* bus type (0 == PCI, 1 == EISA) */
- u16 base_addr; /* base I/O address (same as dev->base_addr) */
- struct pci_dev * pci_dev;
+ union {
+ void __iomem *mem;
+ int port;
+ } base; /* base address */
+ struct device *bus_dev;
u32 full_duplex_enb; /* FDDI Full Duplex enable (1 == on, 2 == off) */
u32 req_ttrt; /* requested TTRT value (in 80ns units) */
u32 burst_size; /* adapter burst size (enumerated) */