diff --git a/arch/arm/mach-pxa/spitz_pm.c b/arch/arm/mach-pxa/spitz_pm.c
new file mode 100644
index 0000000..3ce7486
--- /dev/null
+++ b/arch/arm/mach-pxa/spitz_pm.c
@@ -0,0 +1,233 @@
+/*
+ * Battery and Power Management code for the Sharp SL-Cxx00
+ *
+ * Copyright (c) 2005 Richard Purdie
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/stat.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <asm/apm.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+#include <asm/hardware.h>
+#include <asm/hardware/scoop.h>
+
+#include <asm/arch/sharpsl.h>
+#include <asm/arch/spitz.h>
+#include <asm/arch/pxa-regs.h>
+#include "sharpsl.h"
+
+static int spitz_last_ac_status;
+
+static void spitz_charger_init(void)
+{
+	pxa_gpio_mode(SPITZ_GPIO_KEY_INT | GPIO_IN);
+	pxa_gpio_mode(SPITZ_GPIO_SYNC | GPIO_IN);
+}
+
+static void spitz_charge_led(int val)
+{
+	if (val == SHARPSL_LED_ERROR) {
+		dev_dbg(sharpsl_pm.dev, "Charge LED Error\n");
+	} else if (val == SHARPSL_LED_ON) {
+		dev_dbg(sharpsl_pm.dev, "Charge LED On\n");
+		set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_LED_ORANGE);
+	} else {
+		dev_dbg(sharpsl_pm.dev, "Charge LED Off\n");
+		reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_LED_ORANGE);
+	}
+}
+
+static void spitz_measure_temp(int on)
+{
+	if (on)
+		set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_ADC_TEMP_ON);
+	else
+		reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_ADC_TEMP_ON);
+}
+
+static void spitz_charge(int on)
+{
+	if (on) {
+		if (sharpsl_pm.flags & SHARPSL_SUSPENDED) {
+			set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_JK_B);
+			reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_CHRG_ON);
+		} else {
+			reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_JK_B);
+			reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_CHRG_ON);
+		}
+	} else {
+		reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_JK_B);
+		set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_CHRG_ON);
+	}
+}
+
+static void spitz_discharge(int on)
+{
+	if (on)
+		set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_JK_A);
+	else
+		reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_JK_A);
+}
+
+/* HACK - For unknown reasons, accurate voltage readings are only made with a load
+   on the power bus which the green led on spitz provides */
+static void spitz_discharge1(int on)
+{
+	if (on)
+		set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_LED_GREEN);
+	else
+		reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_LED_GREEN);
+}
+
+static void spitz_presuspend(void)
+{
+	spitz_last_ac_status = STATUS_AC_IN();
+
+	/* GPIO Sleep Register */
+	PGSR0 = 0x00144018;
+	PGSR1 = 0x00EF0000;
+	if (machine_is_akita()) {
+		PGSR2 = 0x2121C000;
+		PGSR3 = 0x00600400;
+	} else {
+		PGSR2 = 0x0121C000;
+		PGSR3 = 0x00600000;
+	}
+
+	PGSR0 &= ~SPITZ_GPIO_G0_STROBE_BIT;
+	PGSR1 &= ~SPITZ_GPIO_G1_STROBE_BIT;
+	PGSR2 &= ~SPITZ_GPIO_G2_STROBE_BIT;
+	PGSR3 &= ~SPITZ_GPIO_G3_STROBE_BIT;
+	PGSR2 |= GPIO_bit(SPITZ_GPIO_KEY_STROBE0);
+
+	pxa_gpio_mode(GPIO18_RDY|GPIO_OUT | GPIO_DFLT_HIGH);
+
+	PRER = GPIO_bit(SPITZ_GPIO_KEY_INT);
+	PFER = GPIO_bit(SPITZ_GPIO_KEY_INT) | GPIO_bit(SPITZ_GPIO_RESET);
+	PWER = GPIO_bit(SPITZ_GPIO_KEY_INT) | GPIO_bit(SPITZ_GPIO_RESET) | PWER_RTC;
+	PKWR = GPIO_bit(SPITZ_GPIO_SYNC) | GPIO_bit(SPITZ_GPIO_KEY_INT) | GPIO_bit(SPITZ_GPIO_RESET);
+	PKSR = 0xffffffff; // clear
+
+	/* nRESET_OUT Disable */
+	PSLR |= PSLR_SL_ROD;
+
+	/* Clear reset status */
+	RCSR = RCSR_HWR | RCSR_WDR | RCSR_SMR | RCSR_GPR;
+
+	/* Stop 3.6MHz and drive HIGH to PCMCIA and CS */
+	PCFR = PCFR_GPR_EN | PCFR_OPDE;
+}
+
+static void spitz_postsuspend(void)
+{
+	pxa_gpio_mode(GPIO18_RDY_MD);
+	pxa_gpio_mode(10 | GPIO_IN);
+}
+
+static int spitz_should_wakeup(unsigned int resume_on_alarm)
+{
+	int is_resume = 0;
+	int acin = STATUS_AC_IN();
+
+	if (spitz_last_ac_status != acin) {
+		if (acin) {
+			/* charge on */
+			sharpsl_pm.flags |= SHARPSL_DO_OFFLINE_CHRG;
+			dev_dbg(sharpsl_pm.dev, "AC Inserted\n");
+		} else {
+			/* charge off */
+			dev_dbg(sharpsl_pm.dev, "AC Removed\n");
+			CHARGE_LED_OFF();
+			CHARGE_OFF();
+			sharpsl_pm.charge_mode = CHRG_OFF;
+		}
+		spitz_last_ac_status = acin;
+		/* Return to suspend as this must be what we were woken for */
+		return 0;
+	}
+
+	if (PEDR & GPIO_bit(SPITZ_GPIO_KEY_INT))
+		is_resume |= GPIO_bit(SPITZ_GPIO_KEY_INT);
+
+	if (PKSR & GPIO_bit(SPITZ_GPIO_SYNC))
+		is_resume |= GPIO_bit(SPITZ_GPIO_SYNC);
+
+	if (resume_on_alarm && (PEDR & PWER_RTC))
+		is_resume |= PWER_RTC;
+
+	dev_dbg(sharpsl_pm.dev, "is_resume: %x\n",is_resume);
+	return is_resume;
+}
+
+static unsigned long spitz_charger_wakeup(void)
+{
+	return (~GPLR0 & GPIO_bit(SPITZ_GPIO_KEY_INT)) | (GPLR0 & GPIO_bit(SPITZ_GPIO_SYNC));
+}
+
+static int spitz_acin_status(void)
+{
+	return (((~GPLR(SPITZ_GPIO_AC_IN)) & GPIO_bit(SPITZ_GPIO_AC_IN)) != 0);
+}
+
+struct sharpsl_charger_machinfo spitz_pm_machinfo = {
+	.init             = spitz_charger_init,
+	.gpio_batlock     = SPITZ_GPIO_BAT_COVER,
+	.gpio_acin        = SPITZ_GPIO_AC_IN,
+	.gpio_batfull     = SPITZ_GPIO_CHRG_FULL,
+	.gpio_fatal       = SPITZ_GPIO_FATAL_BAT,
+	.status_acin      = spitz_acin_status,
+	.discharge        = spitz_discharge,
+	.discharge1       = spitz_discharge1,
+	.charge           = spitz_charge,
+	.chargeled        = spitz_charge_led,
+	.measure_temp     = spitz_measure_temp,
+	.presuspend       = spitz_presuspend,
+	.postsuspend      = spitz_postsuspend,
+	.charger_wakeup   = spitz_charger_wakeup,
+	.should_wakeup    = spitz_should_wakeup,
+	.bat_levels       = 40,
+	.bat_levels_noac  = spitz_battery_levels_noac,
+	.bat_levels_acin  = spitz_battery_levels_acin,
+	.status_high_acin = 188,
+	.status_low_acin  = 178,
+	.status_high_noac = 185,
+	.status_low_noac  = 175,
+};
+
+static struct platform_device *spitzpm_device;
+
+static int __devinit spitzpm_init(void)
+{
+	int ret;
+
+	spitzpm_device = platform_device_alloc("sharpsl-pm", -1);
+	if (!spitzpm_device)
+		return -ENOMEM;
+
+	spitzpm_device->dev.platform_data = &spitz_pm_machinfo;
+	ret = platform_device_add(spitzpm_device);
+
+	if (ret)
+		platform_device_put(spitzpm_device);
+
+	return ret;
+}
+
+static void spitzpm_exit(void)
+{
+ 	platform_device_unregister(spitzpm_device);
+}
+
+module_init(spitzpm_init);
+module_exit(spitzpm_exit);