[ARM] 4348/4: iop3xx: Give Linux control over PCI initialization
Currently the iop3xx platform support code assumes that RedBoot is the
bootloader and has already initialized the ATU. Linux should handle this
initialization for three reasons:
1/ The memory map that RedBoot sets up is not optimal (page_to_dma and
virt_to_phys return different addresses). The effect of this is that using
the dma mapping API for the internal bus dma units generates pci bus
addresses that are incorrect for the internal bus.
2/ Not all iop platforms use RedBoot
3/ If the ATU is already initialized it indicates that the iop is an add-in
card in another host, it does not own the PCI bus, and should not be
re-initialized.
Changelog:
* rather than change nr_controllers to zero, simply do not call
pci_common_init
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
diff --git a/arch/arm/mach-iop32x/Kconfig b/arch/arm/mach-iop32x/Kconfig
index 9dd49cf..9bb02b6 100644
--- a/arch/arm/mach-iop32x/Kconfig
+++ b/arch/arm/mach-iop32x/Kconfig
@@ -34,6 +34,14 @@
Say Y here if you want to run your kernel on the Thecus n2100
NAS appliance.
+config IOP3XX_ATU
+ bool "Enable the PCI Controller"
+ default y
+ help
+ Say Y here if you want the IOP to initialize its PCI Controller.
+ Say N if the IOP is an add in card, the host system owns the PCI
+ bus in this case.
+
endmenu
endif
diff --git a/arch/arm/mach-iop32x/iq31244.c b/arch/arm/mach-iop32x/iq31244.c
index 60e7430..7b21c6e 100644
--- a/arch/arm/mach-iop32x/iq31244.c
+++ b/arch/arm/mach-iop32x/iq31244.c
@@ -178,9 +178,10 @@
static int __init iq31244_pci_init(void)
{
- if (is_ep80219())
- pci_common_init(&ep80219_pci);
- else if (machine_is_iq31244()) {
+ if (is_ep80219()) {
+ if (iop3xx_get_init_atu() == IOP3XX_INIT_ATU_ENABLE)
+ pci_common_init(&ep80219_pci);
+ } else if (machine_is_iq31244()) {
if (is_80219()) {
printk("note: iq31244 board type has been selected\n");
printk("note: to select ep80219 operation:\n");
@@ -189,7 +190,9 @@
printk("\t2/ update boot loader to pass"
" the ep80219 id: %d\n", MACH_TYPE_EP80219);
}
- pci_common_init(&iq31244_pci);
+
+ if (iop3xx_get_init_atu() == IOP3XX_INIT_ATU_ENABLE)
+ pci_common_init(&iq31244_pci);
}
return 0;
diff --git a/arch/arm/mach-iop32x/iq80321.c b/arch/arm/mach-iop32x/iq80321.c
index 361c70c..bc25fb9 100644
--- a/arch/arm/mach-iop32x/iq80321.c
+++ b/arch/arm/mach-iop32x/iq80321.c
@@ -113,7 +113,8 @@
static int __init iq80321_pci_init(void)
{
- if (machine_is_iq80321())
+ if ((iop3xx_get_init_atu() == IOP3XX_INIT_ATU_ENABLE) &&
+ machine_is_iq80321())
pci_common_init(&iq80321_pci);
return 0;
diff --git a/arch/arm/mach-iop33x/Kconfig b/arch/arm/mach-iop33x/Kconfig
index 9aa016b..45598e0 100644
--- a/arch/arm/mach-iop33x/Kconfig
+++ b/arch/arm/mach-iop33x/Kconfig
@@ -16,6 +16,14 @@
Say Y here if you want to run your kernel on the Intel IQ80332
evaluation kit for the IOP332 chipset.
+config IOP3XX_ATU
+ bool "Enable the PCI Controller"
+ default y
+ help
+ Say Y here if you want the IOP to initialize its PCI Controller.
+ Say N if the IOP is an add in card, the host system owns the PCI
+ bus in this case.
+
endmenu
endif
diff --git a/arch/arm/mach-iop33x/iq80331.c b/arch/arm/mach-iop33x/iq80331.c
index 1a9e361..376c932 100644
--- a/arch/arm/mach-iop33x/iq80331.c
+++ b/arch/arm/mach-iop33x/iq80331.c
@@ -96,7 +96,8 @@
static int __init iq80331_pci_init(void)
{
- if (machine_is_iq80331())
+ if ((iop3xx_get_init_atu() == IOP3XX_INIT_ATU_ENABLE) &&
+ machine_is_iq80331())
pci_common_init(&iq80331_pci);
return 0;
diff --git a/arch/arm/mach-iop33x/iq80332.c b/arch/arm/mach-iop33x/iq80332.c
index 96d6f0f..58c8149 100644
--- a/arch/arm/mach-iop33x/iq80332.c
+++ b/arch/arm/mach-iop33x/iq80332.c
@@ -96,7 +96,8 @@
static int __init iq80332_pci_init(void)
{
- if (machine_is_iq80332())
+ if ((iop3xx_get_init_atu() == IOP3XX_INIT_ATU_ENABLE) &&
+ machine_is_iq80332())
pci_common_init(&iq80332_pci);
return 0;
diff --git a/arch/arm/plat-iop/pci.c b/arch/arm/plat-iop/pci.c
index b5f6ec3..e2744b7 100644
--- a/arch/arm/plat-iop/pci.c
+++ b/arch/arm/plat-iop/pci.c
@@ -55,7 +55,7 @@
* This routine checks the status of the last configuration cycle. If an error
* was detected it returns a 1, else it returns a 0. The errors being checked
* are parity, master abort, target abort (master and target). These types of
- * errors occure during a config cycle where there is no device, like during
+ * errors occur during a config cycle where there is no device, like during
* the discovery stage.
*/
static int iop3xx_pci_status(void)
@@ -223,8 +223,111 @@
return pci_scan_bus(sys->busnr, &iop3xx_ops, sys);
}
+void __init iop3xx_atu_setup(void)
+{
+ /* BAR 0 ( Disabled ) */
+ *IOP3XX_IAUBAR0 = 0x0;
+ *IOP3XX_IABAR0 = 0x0;
+ *IOP3XX_IATVR0 = 0x0;
+ *IOP3XX_IALR0 = 0x0;
+
+ /* BAR 1 ( Disabled ) */
+ *IOP3XX_IAUBAR1 = 0x0;
+ *IOP3XX_IABAR1 = 0x0;
+ *IOP3XX_IALR1 = 0x0;
+
+ /* BAR 2 (1:1 mapping with Physical RAM) */
+ /* Set limit and enable */
+ *IOP3XX_IALR2 = ~((u32)IOP3XX_MAX_RAM_SIZE - 1) & ~0x1;
+ *IOP3XX_IAUBAR2 = 0x0;
+
+ /* Align the inbound bar with the base of memory */
+ *IOP3XX_IABAR2 = PHYS_OFFSET |
+ PCI_BASE_ADDRESS_MEM_TYPE_64 |
+ PCI_BASE_ADDRESS_MEM_PREFETCH;
+
+ *IOP3XX_IATVR2 = PHYS_OFFSET;
+
+ /* Outbound window 0 */
+ *IOP3XX_OMWTVR0 = IOP3XX_PCI_LOWER_MEM_PA;
+ *IOP3XX_OUMWTVR0 = 0;
+
+ /* Outbound window 1 */
+ *IOP3XX_OMWTVR1 = IOP3XX_PCI_LOWER_MEM_PA + IOP3XX_PCI_MEM_WINDOW_SIZE;
+ *IOP3XX_OUMWTVR1 = 0;
+
+ /* BAR 3 ( Disabled ) */
+ *IOP3XX_IAUBAR3 = 0x0;
+ *IOP3XX_IABAR3 = 0x0;
+ *IOP3XX_IATVR3 = 0x0;
+ *IOP3XX_IALR3 = 0x0;
+
+ /* Setup the I/O Bar
+ */
+ *IOP3XX_OIOWTVR = IOP3XX_PCI_LOWER_IO_PA;;
+
+ /* Enable inbound and outbound cycles
+ */
+ *IOP3XX_ATUCMD |= PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER |
+ PCI_COMMAND_PARITY | PCI_COMMAND_SERR;
+ *IOP3XX_ATUCR |= IOP3XX_ATUCR_OUT_EN;
+}
+
+void __init iop3xx_atu_disable(void)
+{
+ *IOP3XX_ATUCMD = 0;
+ *IOP3XX_ATUCR = 0;
+
+ /* wait for cycles to quiesce */
+ while (*IOP3XX_PCSR & (IOP3XX_PCSR_OUT_Q_BUSY |
+ IOP3XX_PCSR_IN_Q_BUSY))
+ cpu_relax();
+
+ /* BAR 0 ( Disabled ) */
+ *IOP3XX_IAUBAR0 = 0x0;
+ *IOP3XX_IABAR0 = 0x0;
+ *IOP3XX_IATVR0 = 0x0;
+ *IOP3XX_IALR0 = 0x0;
+
+ /* BAR 1 ( Disabled ) */
+ *IOP3XX_IAUBAR1 = 0x0;
+ *IOP3XX_IABAR1 = 0x0;
+ *IOP3XX_IALR1 = 0x0;
+
+ /* BAR 2 ( Disabled ) */
+ *IOP3XX_IAUBAR2 = 0x0;
+ *IOP3XX_IABAR2 = 0x0;
+ *IOP3XX_IATVR2 = 0x0;
+ *IOP3XX_IALR2 = 0x0;
+
+ /* BAR 3 ( Disabled ) */
+ *IOP3XX_IAUBAR3 = 0x0;
+ *IOP3XX_IABAR3 = 0x0;
+ *IOP3XX_IATVR3 = 0x0;
+ *IOP3XX_IALR3 = 0x0;
+
+ /* Clear the outbound windows */
+ *IOP3XX_OIOWTVR = 0;
+
+ /* Outbound window 0 */
+ *IOP3XX_OMWTVR0 = 0;
+ *IOP3XX_OUMWTVR0 = 0;
+
+ /* Outbound window 1 */
+ *IOP3XX_OMWTVR1 = 0;
+ *IOP3XX_OUMWTVR1 = 0;
+}
+
+/* Flag to determine whether the ATU is initialized and the PCI bus scanned */
+int init_atu;
+
void iop3xx_pci_preinit(void)
{
+ if (iop3xx_get_init_atu() == IOP3XX_INIT_ATU_ENABLE) {
+ iop3xx_atu_disable();
+ iop3xx_atu_setup();
+ }
+
DBG("PCI: Intel 803xx PCI init code.\n");
DBG("ATU: IOP3XX_ATUCMD=0x%04x\n", *IOP3XX_ATUCMD);
DBG("ATU: IOP3XX_OMWTVR0=0x%04x, IOP3XX_OIOWTVR=0x%04x\n",
@@ -245,3 +348,38 @@
hook_fault_code(16+6, iop3xx_pci_abort, SIGBUS, "imprecise external abort");
}
+
+/* allow init_atu to be user overridden */
+static int __init iop3xx_init_atu_setup(char *str)
+{
+ init_atu = IOP3XX_INIT_ATU_DEFAULT;
+ if (str) {
+ while (*str != '\0') {
+ switch (*str) {
+ case 'y':
+ case 'Y':
+ init_atu = IOP3XX_INIT_ATU_ENABLE;
+ break;
+ case 'n':
+ case 'N':
+ init_atu = IOP3XX_INIT_ATU_DISABLE;
+ break;
+ case ',':
+ case '=':
+ break;
+ default:
+ printk(KERN_DEBUG "\"%s\" malformed at "
+ "character: \'%c\'",
+ __FUNCTION__,
+ *str);
+ *(str + 1) = '\0';
+ }
+ str++;
+ }
+ }
+
+ return 1;
+}
+
+__setup("iop3xx_init_atu", iop3xx_init_atu_setup);
+