| /* |
| * Copyright 2011-2013 Freescale Semiconductor, Inc. |
| * Copyright 2011 Linaro Ltd. |
| * |
| * The code contained herein is licensed under the GNU General Public |
| * License. You may obtain a copy of the GNU General Public License |
| * Version 2 or later at the following locations: |
| * |
| * http://www.opensource.org/licenses/gpl-license.html |
| * http://www.gnu.org/copyleft/gpl.html |
| */ |
| |
| #include <linux/clk.h> |
| #include <linux/clkdev.h> |
| #include <linux/cpu.h> |
| #include <linux/delay.h> |
| #include <linux/export.h> |
| #include <linux/init.h> |
| #include <linux/io.h> |
| #include <linux/irq.h> |
| #include <linux/irqchip.h> |
| #include <linux/of.h> |
| #include <linux/of_address.h> |
| #include <linux/of_irq.h> |
| #include <linux/of_platform.h> |
| #include <linux/opp.h> |
| #include <linux/phy.h> |
| #include <linux/regmap.h> |
| #include <linux/micrel_phy.h> |
| #include <linux/mfd/syscon.h> |
| #include <asm/smp_twd.h> |
| #include <asm/hardware/cache-l2x0.h> |
| #include <asm/mach/arch.h> |
| #include <asm/mach/map.h> |
| #include <asm/mach/time.h> |
| #include <asm/system_misc.h> |
| |
| #include "common.h" |
| #include "cpuidle.h" |
| #include "hardware.h" |
| |
| static int imx6q_revision(void) |
| { |
| static u32 rev; |
| |
| if (!rev) |
| rev = imx_anatop_get_digprog(); |
| |
| switch (rev & 0xff) { |
| case 0: |
| return IMX_CHIP_REVISION_1_0; |
| case 1: |
| return IMX_CHIP_REVISION_1_1; |
| case 2: |
| return IMX_CHIP_REVISION_1_2; |
| default: |
| return IMX_CHIP_REVISION_UNKNOWN; |
| } |
| } |
| |
| void imx6q_restart(char mode, const char *cmd) |
| { |
| struct device_node *np; |
| void __iomem *wdog_base; |
| |
| np = of_find_compatible_node(NULL, NULL, "fsl,imx6q-wdt"); |
| wdog_base = of_iomap(np, 0); |
| if (!wdog_base) |
| goto soft; |
| |
| imx_src_prepare_restart(); |
| |
| /* enable wdog */ |
| writew_relaxed(1 << 2, wdog_base); |
| /* write twice to ensure the request will not get ignored */ |
| writew_relaxed(1 << 2, wdog_base); |
| |
| /* wait for reset to assert ... */ |
| mdelay(500); |
| |
| pr_err("Watchdog reset failed to assert reset\n"); |
| |
| /* delay to allow the serial port to show the message */ |
| mdelay(50); |
| |
| soft: |
| /* we'll take a jump through zero as a poor second */ |
| soft_restart(0); |
| } |
| |
| /* For imx6q sabrelite board: set KSZ9021RN RGMII pad skew */ |
| static int ksz9021rn_phy_fixup(struct phy_device *phydev) |
| { |
| if (IS_BUILTIN(CONFIG_PHYLIB)) { |
| /* min rx data delay */ |
| phy_write(phydev, 0x0b, 0x8105); |
| phy_write(phydev, 0x0c, 0x0000); |
| |
| /* max rx/tx clock delay, min rx/tx control delay */ |
| phy_write(phydev, 0x0b, 0x8104); |
| phy_write(phydev, 0x0c, 0xf0f0); |
| phy_write(phydev, 0x0b, 0x104); |
| } |
| |
| return 0; |
| } |
| |
| static void __init imx6q_sabrelite_cko1_setup(void) |
| { |
| struct clk *cko1_sel, *ahb, *cko1; |
| unsigned long rate; |
| |
| cko1_sel = clk_get_sys(NULL, "cko1_sel"); |
| ahb = clk_get_sys(NULL, "ahb"); |
| cko1 = clk_get_sys(NULL, "cko1"); |
| if (IS_ERR(cko1_sel) || IS_ERR(ahb) || IS_ERR(cko1)) { |
| pr_err("cko1 setup failed!\n"); |
| goto put_clk; |
| } |
| clk_set_parent(cko1_sel, ahb); |
| rate = clk_round_rate(cko1, 16000000); |
| clk_set_rate(cko1, rate); |
| put_clk: |
| if (!IS_ERR(cko1_sel)) |
| clk_put(cko1_sel); |
| if (!IS_ERR(ahb)) |
| clk_put(ahb); |
| if (!IS_ERR(cko1)) |
| clk_put(cko1); |
| } |
| |
| static void __init imx6q_sabrelite_init(void) |
| { |
| if (IS_BUILTIN(CONFIG_PHYLIB)) |
| phy_register_fixup_for_uid(PHY_ID_KSZ9021, MICREL_PHY_ID_MASK, |
| ksz9021rn_phy_fixup); |
| imx6q_sabrelite_cko1_setup(); |
| } |
| |
| static void __init imx6q_1588_init(void) |
| { |
| struct regmap *gpr; |
| |
| gpr = syscon_regmap_lookup_by_compatible("fsl,imx6q-iomuxc-gpr"); |
| if (!IS_ERR(gpr)) |
| regmap_update_bits(gpr, 0x4, 1 << 21, 1 << 21); |
| else |
| pr_err("failed to find fsl,imx6q-iomux-gpr regmap\n"); |
| |
| } |
| static void __init imx6q_usb_init(void) |
| { |
| imx_anatop_usb_chrg_detect_disable(); |
| } |
| |
| static void __init imx6q_init_machine(void) |
| { |
| if (of_machine_is_compatible("fsl,imx6q-sabrelite")) |
| imx6q_sabrelite_init(); |
| |
| of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL); |
| |
| imx_anatop_init(); |
| imx6q_pm_init(); |
| imx6q_usb_init(); |
| imx6q_1588_init(); |
| imx_print_silicon_rev("i.MX6Q", imx6q_revision()); |
| } |
| |
| #define OCOTP_CFG3 0x440 |
| #define OCOTP_CFG3_SPEED_SHIFT 16 |
| #define OCOTP_CFG3_SPEED_1P2GHZ 0x3 |
| |
| static void __init imx6q_opp_check_1p2ghz(struct device *cpu_dev) |
| { |
| struct device_node *np; |
| void __iomem *base; |
| u32 val; |
| |
| np = of_find_compatible_node(NULL, NULL, "fsl,imx6q-ocotp"); |
| if (!np) { |
| pr_warn("failed to find ocotp node\n"); |
| return; |
| } |
| |
| base = of_iomap(np, 0); |
| if (!base) { |
| pr_warn("failed to map ocotp\n"); |
| goto put_node; |
| } |
| |
| val = readl_relaxed(base + OCOTP_CFG3); |
| val >>= OCOTP_CFG3_SPEED_SHIFT; |
| if ((val & 0x3) != OCOTP_CFG3_SPEED_1P2GHZ) |
| if (opp_disable(cpu_dev, 1200000000)) |
| pr_warn("failed to disable 1.2 GHz OPP\n"); |
| |
| put_node: |
| of_node_put(np); |
| } |
| |
| static void __init imx6q_opp_init(struct device *cpu_dev) |
| { |
| struct device_node *np; |
| |
| np = of_find_node_by_path("/cpus/cpu@0"); |
| if (!np) { |
| pr_warn("failed to find cpu0 node\n"); |
| return; |
| } |
| |
| cpu_dev->of_node = np; |
| if (of_init_opp_table(cpu_dev)) { |
| pr_warn("failed to init OPP table\n"); |
| goto put_node; |
| } |
| |
| imx6q_opp_check_1p2ghz(cpu_dev); |
| |
| put_node: |
| of_node_put(np); |
| } |
| |
| struct platform_device imx6q_cpufreq_pdev = { |
| .name = "imx6q-cpufreq", |
| }; |
| |
| static void __init imx6q_init_late(void) |
| { |
| /* |
| * WAIT mode is broken on TO 1.0 and 1.1, so there is no point |
| * to run cpuidle on them. |
| */ |
| if (imx6q_revision() > IMX_CHIP_REVISION_1_1) |
| imx6q_cpuidle_init(); |
| |
| if (IS_ENABLED(CONFIG_ARM_IMX6Q_CPUFREQ)) { |
| imx6q_opp_init(&imx6q_cpufreq_pdev.dev); |
| platform_device_register(&imx6q_cpufreq_pdev); |
| } |
| } |
| |
| static void __init imx6q_map_io(void) |
| { |
| debug_ll_io_init(); |
| imx_scu_map_io(); |
| } |
| |
| static void __init imx6q_init_irq(void) |
| { |
| l2x0_of_init(0, ~0UL); |
| imx_src_init(); |
| imx_gpc_init(); |
| irqchip_init(); |
| } |
| |
| static void __init imx6q_timer_init(void) |
| { |
| mx6q_clocks_init(); |
| twd_local_timer_of_register(); |
| } |
| |
| static const char *imx6q_dt_compat[] __initdata = { |
| "fsl,imx6q", |
| NULL, |
| }; |
| |
| DT_MACHINE_START(IMX6Q, "Freescale i.MX6 Quad (Device Tree)") |
| .smp = smp_ops(imx_smp_ops), |
| .map_io = imx6q_map_io, |
| .init_irq = imx6q_init_irq, |
| .init_time = imx6q_timer_init, |
| .init_machine = imx6q_init_machine, |
| .init_late = imx6q_init_late, |
| .dt_compat = imx6q_dt_compat, |
| .restart = imx6q_restart, |
| MACHINE_END |