[ALSA] sscape: support for audio part of VIVO cards
This patch adds support for audio part of the Ensoniq
SoundScape VIVO cards. The MIDI part is not supported.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
diff --git a/sound/isa/sscape.c b/sound/isa/sscape.c
index 53daa8b..4902da4 100644
--- a/sound/isa/sscape.c
+++ b/sound/isa/sscape.c
@@ -142,10 +142,12 @@
struct soundscape {
spinlock_t lock;
unsigned io_base;
+ unsigned wss_base;
int codec_type;
int ic_type;
enum card_type type;
struct resource *io_res;
+ struct resource *wss_res;
struct snd_cs4231 *chip;
struct snd_mpu401 *mpu;
struct snd_hwdep *hw;
@@ -356,8 +358,9 @@
*/
static void soundscape_free(struct snd_card *c)
{
- register struct soundscape *sscape = get_card_soundscape(c);
+ struct soundscape *sscape = get_card_soundscape(c);
release_and_free_resource(sscape->io_res);
+ release_and_free_resource(sscape->wss_res);
free_dma(sscape->chip->dma1);
}
@@ -818,6 +821,7 @@
unsigned long flags;
unsigned d;
int retval = 0;
+ int codec = s->wss_base;
spin_lock_irqsave(&s->lock, flags);
@@ -849,9 +853,27 @@
outb(0xfe, ODIE_ADDR_IO(s->io_base));
if ((inb(ODIE_ADDR_IO(s->io_base)) & 0x9f) != 0x0e)
goto _done;
- if ((inb(ODIE_DATA_IO(s->io_base)) & 0x9f) != 0x0e)
+
+ outb(0xfe, ODIE_ADDR_IO(s->io_base));
+ d = inb(ODIE_DATA_IO(s->io_base));
+ if (s->type != SSCAPE_VIVO && (d & 0x9f) != 0x0e)
goto _done;
+ d = sscape_read_unsafe(s->io_base, GA_HMCTL_REG) & 0x3f;
+ sscape_write_unsafe(s->io_base, GA_HMCTL_REG, d | 0xc0);
+
+ if (s->type == SSCAPE_VIVO)
+ codec += 4;
+ /* wait for WSS codec */
+ for (d = 0; d < 500; d++) {
+ if ((inb(codec) & 0x80) == 0)
+ break;
+ spin_unlock_irqrestore(&s->lock, flags);
+ msleep(1);
+ spin_lock_irqsave(&s->lock, flags);
+ }
+ snd_printd(KERN_INFO "init delay = %d ms\n", d);
+
/*
* SoundScape successfully detected!
*/
@@ -1018,6 +1040,9 @@
struct snd_cs4231 *chip;
int err;
+ if (sscape->type == SSCAPE_VIVO)
+ port += 4;
+
if (dma1 == dma2)
dma2 = -1;
@@ -1046,40 +1071,63 @@
snd_cs4231_mce_down(chip);
*/
- /*
- * The input clock frequency on the SoundScape must
- * be 14.31818 MHz, because we must set this register
- * to get the playback to sound correct ...
- */
- snd_cs4231_mce_up(chip);
- spin_lock_irqsave(&chip->reg_lock, flags);
- snd_cs4231_out(chip, AD1845_CRYS_CLOCK_SEL, 0x20);
- spin_unlock_irqrestore(&chip->reg_lock, flags);
- snd_cs4231_mce_down(chip);
+ if (sscape->type != SSCAPE_VIVO) {
+ int val;
+ /*
+ * The input clock frequency on the SoundScape must
+ * be 14.31818 MHz, because we must set this register
+ * to get the playback to sound correct ...
+ */
+ snd_cs4231_mce_up(chip);
+ spin_lock_irqsave(&chip->reg_lock, flags);
+ snd_cs4231_out(chip, AD1845_CRYS_CLOCK_SEL, 0x20);
+ spin_unlock_irqrestore(&chip->reg_lock, flags);
+ snd_cs4231_mce_down(chip);
- /*
- * More custom configuration:
- * a) select "mode 2", and provide a current drive of 8 mA
- * b) enable frequency selection (for capture/playback)
- */
- spin_lock_irqsave(&chip->reg_lock, flags);
- snd_cs4231_out(chip, CS4231_MISC_INFO, (CS4231_MODE2 | 0x10));
- snd_cs4231_out(chip, AD1845_PWR_DOWN_CTRL, snd_cs4231_in(chip, AD1845_PWR_DOWN_CTRL) | AD1845_FREQ_SEL_ENABLE);
- spin_unlock_irqrestore(&chip->reg_lock, flags);
+ /*
+ * More custom configuration:
+ * a) select "mode 2" and provide a current drive of 8mA
+ * b) enable frequency selection (for capture/playback)
+ */
+ spin_lock_irqsave(&chip->reg_lock, flags);
+ snd_cs4231_out(chip, CS4231_MISC_INFO,
+ CS4231_MODE2 | 0x10);
+ val = snd_cs4231_in(chip, AD1845_PWR_DOWN_CTRL);
+ snd_cs4231_out(chip, AD1845_PWR_DOWN_CTRL,
+ val | AD1845_FREQ_SEL_ENABLE);
+ spin_unlock_irqrestore(&chip->reg_lock, flags);
+ }
- if ((err = snd_cs4231_pcm(chip, 0, &pcm)) < 0) {
- snd_printk(KERN_ERR "sscape: No PCM device for AD1845 chip\n");
+ err = snd_cs4231_pcm(chip, 0, &pcm);
+ if (err < 0) {
+ snd_printk(KERN_ERR "sscape: No PCM device "
+ "for AD1845 chip\n");
goto _error;
}
- if ((err = snd_cs4231_mixer(chip)) < 0) {
- snd_printk(KERN_ERR "sscape: No mixer device for AD1845 chip\n");
+ err = snd_cs4231_mixer(chip);
+ if (err < 0) {
+ snd_printk(KERN_ERR "sscape: No mixer device "
+ "for AD1845 chip\n");
+ goto _error;
+ }
+ err = snd_cs4231_timer(chip, 0, NULL);
+ if (err < 0) {
+ snd_printk(KERN_ERR "sscape: No timer device "
+ "for AD1845 chip\n");
goto _error;
}
- if ((err = snd_ctl_add(card, snd_ctl_new1(&midi_mixer_ctl, chip))) < 0) {
- snd_printk(KERN_ERR "sscape: Could not create MIDI mixer control\n");
- goto _error;
+ if (sscape->type != SSCAPE_VIVO) {
+ err = snd_ctl_add(card,
+ snd_ctl_new1(&midi_mixer_ctl, chip));
+ if (err < 0) {
+ snd_printk(KERN_ERR "sscape: Could not create "
+ "MIDI mixer control\n");
+ goto _error;
+ }
+ chip->set_playback_format = ad1845_playback_format;
+ chip->set_capture_format = ad1845_capture_format;
}
strcpy(card->driver, "SoundScape");
@@ -1088,8 +1136,7 @@
"%s at 0x%lx, IRQ %d, DMA1 %d, DMA2 %d\n",
pcm->name, chip->port, chip->irq,
chip->dma1, chip->dma2);
- chip->set_playback_format = ad1845_playback_format;
- chip->set_capture_format = ad1845_capture_format;
+
sscape->chip = chip;
}
@@ -1104,12 +1151,13 @@
*/
static int __devinit create_sscape(int dev, struct snd_card *card)
{
- register struct soundscape *sscape;
- register unsigned dma_cfg;
+ struct soundscape *sscape = get_card_soundscape(card);
+ unsigned dma_cfg;
unsigned irq_cfg;
unsigned mpu_irq_cfg;
unsigned xport;
struct resource *io_res;
+ struct resource *wss_res;
unsigned long flags;
int err;
@@ -1133,13 +1181,24 @@
* Grab IO ports that we will need to probe so that we
* can detect and control this hardware ...
*/
- if ((io_res = request_region(xport, 8, "SoundScape")) == NULL) {
+ io_res = request_region(xport, 8, "SoundScape");
+ if (!io_res) {
snd_printk(KERN_ERR "sscape: can't grab port 0x%x\n", xport);
return -EBUSY;
}
+ wss_res = NULL;
+ if (sscape->type == SSCAPE_VIVO) {
+ wss_res = request_region(wss_port[dev], 4, "SoundScape");
+ if (!wss_res) {
+ snd_printk(KERN_ERR "sscape: can't grab port 0x%lx\n",
+ wss_port[dev]);
+ err = -EBUSY;
+ goto _release_region;
+ }
+ }
/*
- * Grab both DMA channels (OK, only one for now) ...
+ * Grab one DMA channel ...
*/
err = request_dma(dma[dev], "SoundScape");
if (err < 0) {
@@ -1147,11 +1206,12 @@
goto _release_region;
}
- sscape = get_card_soundscape(card);
spin_lock_init(&sscape->lock);
spin_lock_init(&sscape->fwlock);
sscape->io_res = io_res;
+ sscape->wss_res = wss_res;
sscape->io_base = xport;
+ sscape->wss_base = wss_port[dev];
if (!detect_sscape(sscape)) {
printk(KERN_ERR "sscape: hardware not detected at 0x%x\n", sscape->io_base);
@@ -1162,23 +1222,28 @@
printk(KERN_INFO "sscape: hardware detected at 0x%x, using IRQ %d, DMA %d\n",
sscape->io_base, irq[dev], dma[dev]);
- /*
- * Now create the hardware-specific device so that we can
- * load the microcode into the on-board processor.
- * We cannot use the MPU-401 MIDI system until this firmware
- * has been loaded into the card.
- */
- if ((err = snd_hwdep_new(card, "MC68EC000", 0, &(sscape->hw))) < 0) {
- printk(KERN_ERR "sscape: Failed to create firmware device\n");
- goto _release_dma;
+ if (sscape->type != SSCAPE_VIVO) {
+ /*
+ * Now create the hardware-specific device so that we can
+ * load the microcode into the on-board processor.
+ * We cannot use the MPU-401 MIDI system until this firmware
+ * has been loaded into the card.
+ */
+ err = snd_hwdep_new(card, "MC68EC000", 0, &(sscape->hw));
+ if (err < 0) {
+ printk(KERN_ERR "sscape: Failed to create "
+ "firmware device\n");
+ goto _release_dma;
+ }
+ strlcpy(sscape->hw->name, "SoundScape M68K",
+ sizeof(sscape->hw->name));
+ sscape->hw->name[sizeof(sscape->hw->name) - 1] = '\0';
+ sscape->hw->iface = SNDRV_HWDEP_IFACE_SSCAPE;
+ sscape->hw->ops.open = sscape_hw_open;
+ sscape->hw->ops.release = sscape_hw_release;
+ sscape->hw->ops.ioctl = sscape_hw_ioctl;
+ sscape->hw->private_data = sscape;
}
- strlcpy(sscape->hw->name, "SoundScape M68K", sizeof(sscape->hw->name));
- sscape->hw->name[sizeof(sscape->hw->name) - 1] = '\0';
- sscape->hw->iface = SNDRV_HWDEP_IFACE_SSCAPE;
- sscape->hw->ops.open = sscape_hw_open;
- sscape->hw->ops.release = sscape_hw_release;
- sscape->hw->ops.ioctl = sscape_hw_ioctl;
- sscape->hw->private_data = sscape;
/*
* Tell the on-board devices where their resources are (I think -
@@ -1220,26 +1285,31 @@
goto _release_dma;
}
#define MIDI_DEVNUM 0
- if ((err = create_mpu401(card, MIDI_DEVNUM, MPU401_IO(xport), mpu_irq[dev])) < 0) {
- printk(KERN_ERR "sscape: Failed to create MPU-401 device at 0x%x\n",
- MPU401_IO(xport));
- goto _release_dma;
+ if (sscape->type != SSCAPE_VIVO) {
+ err = create_mpu401(card, MIDI_DEVNUM,
+ MPU401_IO(xport), mpu_irq[dev]);
+ if (err < 0) {
+ printk(KERN_ERR "sscape: Failed to create "
+ "MPU-401 device at 0x%x\n",
+ MPU401_IO(xport));
+ goto _release_dma;
+ }
+
+ /*
+ * Enable the master IRQ ...
+ */
+ sscape_write(sscape, GA_INTENA_REG, 0x80);
+
+ /*
+ * Initialize mixer
+ */
+ sscape->midi_vol = 0;
+ host_write_ctrl_unsafe(sscape->io_base, CMD_SET_MIDI_VOL, 100);
+ host_write_ctrl_unsafe(sscape->io_base, 0, 100);
+ host_write_ctrl_unsafe(sscape->io_base, CMD_XXX_MIDI_VOL, 100);
}
/*
- * Enable the master IRQ ...
- */
- sscape_write(sscape, GA_INTENA_REG, 0x80);
-
- /*
- * Initialize mixer
- */
- sscape->midi_vol = 0;
- host_write_ctrl_unsafe(sscape->io_base, CMD_SET_MIDI_VOL, 100);
- host_write_ctrl_unsafe(sscape->io_base, 0, 100);
- host_write_ctrl_unsafe(sscape->io_base, CMD_XXX_MIDI_VOL, 100);
-
- /*
* Now that we have successfully created this sound card,
* it is safe to store the pointer.
* NOTE: we only register the sound card's "destructor"
@@ -1253,6 +1323,7 @@
free_dma(dma[dev]);
_release_region:
+ release_and_free_resource(wss_res);
release_and_free_resource(io_res);
return err;
@@ -1404,12 +1475,6 @@
else
sscape->type = SSCAPE_PNP;
- /* VIVO fails for now */
- if (sscape->type == SSCAPE_VIVO) {
- ret = -ENODEV;
- goto _release_card;
- }
-
/*
* Read the correct parameters off the ISA PnP bus ...
*/
@@ -1417,8 +1482,13 @@
irq[idx] = pnp_irq(dev, 0);
mpu_irq[idx] = pnp_irq(dev, 1);
dma[idx] = pnp_dma(dev, 0) & 0x03;
- dma2[idx] = dma[idx];
- wss_port[idx] = CODEC_IO(port[idx]);
+ if (sscape->type == SSCAPE_PNP) {
+ dma2[idx] = dma[idx];
+ wss_port[idx] = CODEC_IO(port[idx]);
+ } else {
+ wss_port[idx] = pnp_port_start(dev, 1);
+ dma2[idx] = pnp_dma(dev, 1);
+ }
ret = create_sscape(idx, card);
if (ret < 0)