pmac-zilog: add platform driver
Add platform driver support to the pmac-zilog driver, for m68k macs.
Place the powermac-specific code inside #ifdef CONFIG_PPC_PMAC.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
diff --git a/drivers/serial/pmac_zilog.c b/drivers/serial/pmac_zilog.c
index 1c8afd9..f020de1 100644
--- a/drivers/serial/pmac_zilog.c
+++ b/drivers/serial/pmac_zilog.c
@@ -63,11 +63,17 @@
#include <asm/sections.h>
#include <asm/io.h>
#include <asm/irq.h>
+
+#ifdef CONFIG_PPC_PMAC
#include <asm/prom.h>
#include <asm/machdep.h>
#include <asm/pmac_feature.h>
#include <asm/dbdma.h>
#include <asm/macio.h>
+#else
+#include <linux/platform_device.h>
+#define of_machine_is_compatible(x) (0)
+#endif
#if defined (CONFIG_SERIAL_PMACZILOG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
#define SUPPORT_SYSRQ
@@ -83,11 +89,9 @@
static char version[] __initdata = "pmac_zilog: 0.6 (Benjamin Herrenschmidt <benh@kernel.crashing.org>)";
MODULE_AUTHOR("Benjamin Herrenschmidt <benh@kernel.crashing.org>");
-MODULE_DESCRIPTION("Driver for the PowerMac serial ports.");
+MODULE_DESCRIPTION("Driver for the Mac and PowerMac serial ports.");
MODULE_LICENSE("GPL");
-#define PWRDBG(fmt, arg...) printk(KERN_DEBUG fmt , ## arg)
-
#ifdef CONFIG_SERIAL_PMACZILOG_TTYS
#define PMACZILOG_MAJOR TTY_MAJOR
#define PMACZILOG_MINOR 64
@@ -341,7 +345,7 @@
uap->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK);
write_zsreg(uap, R1, uap->curregs[R1]);
zssync(uap);
- dev_err(&uap->dev->ofdev.dev, "pmz: rx irq flood !\n");
+ pmz_error("pmz: rx irq flood !\n");
return tty;
}
@@ -757,6 +761,8 @@
spin_unlock_irqrestore(&port->lock, flags);
}
+#ifdef CONFIG_PPC_PMAC
+
/*
* Turn power on or off to the SCC and associated stuff
* (port drivers, modem, IR port, etc.)
@@ -792,6 +798,15 @@
return delay;
}
+#else
+
+static int pmz_set_scc_power(struct uart_pmac_port *uap, int state)
+{
+ return 0;
+}
+
+#endif /* !CONFIG_PPC_PMAC */
+
/*
* FixZeroBug....Works around a bug in the SCC receving channel.
* Inspired from Darwin code, 15 Sept. 2000 -DanM
@@ -954,9 +969,9 @@
}
pmz_get_port_A(uap)->flags |= PMACZILOG_FLAG_IS_IRQ_ON;
- if (request_irq(uap->port.irq, pmz_interrupt, IRQF_SHARED, "PowerMac Zilog", uap)) {
- dev_err(&uap->dev->ofdev.dev,
- "Unable to register zs interrupt handler.\n");
+ if (request_irq(uap->port.irq, pmz_interrupt, IRQF_SHARED,
+ "SCC", uap)) {
+ pmz_error("Unable to register zs interrupt handler.\n");
pmz_set_scc_power(uap, 0);
mutex_unlock(&pmz_irq_mutex);
return -ENXIO;
@@ -1196,7 +1211,7 @@
while ((read_zsreg(uap, R0) & Tx_BUF_EMP) == 0
|| (read_zsreg(uap, R1) & ALL_SNT) == 0) {
if (--t <= 0) {
- dev_err(&uap->dev->ofdev.dev, "transmitter didn't drain\n");
+ pmz_error("transmitter didn't drain\n");
return;
}
udelay(10);
@@ -1212,7 +1227,7 @@
read_zsdata(uap);
mdelay(10);
if (--t <= 0) {
- dev_err(&uap->dev->ofdev.dev, "receiver didn't drain\n");
+ pmz_error("receiver didn't drain\n");
return;
}
}
@@ -1233,8 +1248,7 @@
t = 5000;
while ((read_zsreg(uap, R0) & Rx_CH_AV) == 0) {
if (--t <= 0) {
- dev_err(&uap->dev->ofdev.dev,
- "irda_setup timed out on get_version byte\n");
+ pmz_error("irda_setup timed out on get_version byte\n");
goto out;
}
udelay(10);
@@ -1242,8 +1256,7 @@
version = read_zsdata(uap);
if (version < 4) {
- dev_info(&uap->dev->ofdev.dev, "IrDA: dongle version %d not supported\n",
- version);
+ pmz_info("IrDA: dongle version %d not supported\n", version);
goto out;
}
@@ -1252,18 +1265,16 @@
t = 5000;
while ((read_zsreg(uap, R0) & Rx_CH_AV) == 0) {
if (--t <= 0) {
- dev_err(&uap->dev->ofdev.dev,
- "irda_setup timed out on speed mode byte\n");
+ pmz_error("irda_setup timed out on speed mode byte\n");
goto out;
}
udelay(10);
}
t = read_zsdata(uap);
if (t != cmdbyte)
- dev_err(&uap->dev->ofdev.dev,
- "irda_setup speed mode byte = %x (%x)\n", t, cmdbyte);
+ pmz_error("irda_setup speed mode byte = %x (%x)\n", t, cmdbyte);
- dev_info(&uap->dev->ofdev.dev, "IrDA setup for %ld bps, dongle version: %d\n",
+ pmz_info("IrDA setup for %ld bps, dongle version: %d\n",
*baud, version);
(void)read_zsdata(uap);
@@ -1413,7 +1424,7 @@
write_zsdata(uap, c);
}
-#endif
+#endif /* CONFIG_CONSOLE_POLL */
static struct uart_ops pmz_pops = {
.tx_empty = pmz_tx_empty,
@@ -1438,6 +1449,8 @@
#endif
};
+#ifdef CONFIG_PPC_PMAC
+
/*
* Setup one port structure after probing, HW is down at this point,
* Unlike sunzilog, we don't need to pre-init the spinlock as we don't
@@ -1834,6 +1847,88 @@
return 0;
}
+#else
+
+extern struct platform_device scc_a_pdev, scc_b_pdev;
+
+static int __init pmz_init_port(struct uart_pmac_port *uap)
+{
+ struct resource *r_ports;
+ int irq;
+
+ r_ports = platform_get_resource(uap->node, IORESOURCE_MEM, 0);
+ irq = platform_get_irq(uap->node, 0);
+ if (!r_ports || !irq)
+ return -ENODEV;
+
+ uap->port.mapbase = r_ports->start;
+ uap->port.membase = (unsigned char __iomem *) r_ports->start;
+ uap->port.iotype = UPIO_MEM;
+ uap->port.irq = irq;
+ uap->port.uartclk = ZS_CLOCK;
+ uap->port.fifosize = 1;
+ uap->port.ops = &pmz_pops;
+ uap->port.type = PORT_PMAC_ZILOG;
+ uap->port.flags = 0;
+
+ uap->control_reg = uap->port.membase;
+ uap->data_reg = uap->control_reg + 4;
+ uap->port_type = 0;
+
+ pmz_convert_to_zs(uap, CS8, 0, 9600);
+
+ return 0;
+}
+
+static int __init pmz_probe(void)
+{
+ int err;
+
+ pmz_ports_count = 0;
+
+ pmz_ports[0].mate = &pmz_ports[1];
+ pmz_ports[0].port.line = 0;
+ pmz_ports[0].flags = PMACZILOG_FLAG_IS_CHANNEL_A;
+ pmz_ports[0].node = &scc_a_pdev;
+ err = pmz_init_port(&pmz_ports[0]);
+ if (err)
+ return err;
+ pmz_ports_count++;
+
+ pmz_ports[1].mate = &pmz_ports[0];
+ pmz_ports[1].port.line = 1;
+ pmz_ports[1].flags = 0;
+ pmz_ports[1].node = &scc_b_pdev;
+ err = pmz_init_port(&pmz_ports[1]);
+ if (err)
+ return err;
+ pmz_ports_count++;
+
+ return 0;
+}
+
+static void pmz_dispose_port(struct uart_pmac_port *uap)
+{
+ memset(uap, 0, sizeof(struct uart_pmac_port));
+}
+
+static int __init pmz_attach(struct platform_device *pdev)
+{
+ int i;
+
+ for (i = 0; i < pmz_ports_count; i++)
+ if (pmz_ports[i].node == pdev)
+ return 0;
+ return -ENODEV;
+}
+
+static int __exit pmz_detach(struct platform_device *pdev)
+{
+ return 0;
+}
+
+#endif /* !CONFIG_PPC_PMAC */
+
#ifdef CONFIG_SERIAL_PMACZILOG_CONSOLE
static void pmz_console_write(struct console *con, const char *s, unsigned int count);
@@ -1894,6 +1989,8 @@
return rc;
}
+#ifdef CONFIG_PPC_PMAC
+
static struct of_device_id pmz_match[] =
{
{
@@ -1915,6 +2012,18 @@
.resume = pmz_resume,
};
+#else
+
+static struct platform_driver pmz_driver = {
+ .remove = __exit_p(pmz_detach),
+ .driver = {
+ .name = "scc",
+ .owner = THIS_MODULE,
+ },
+};
+
+#endif /* !CONFIG_PPC_PMAC */
+
static int __init init_pmz(void)
{
int rc, i;
@@ -1953,15 +2062,23 @@
/*
* Then we register the macio driver itself
*/
+#ifdef CONFIG_PPC_PMAC
return macio_register_driver(&pmz_driver);
+#else
+ return platform_driver_probe(&pmz_driver, pmz_attach);
+#endif
}
static void __exit exit_pmz(void)
{
int i;
+#ifdef CONFIG_PPC_PMAC
/* Get rid of macio-driver (detach from macio) */
macio_unregister_driver(&pmz_driver);
+#else
+ platform_driver_unregister(&pmz_driver);
+#endif
for (i = 0; i < pmz_ports_count; i++) {
struct uart_pmac_port *uport = &pmz_ports[i];