ath9k: make use of conf_is_ht*() in the rest of the driver
Use shiny new conf_is_ht*() helpers, we can later remove ht.enabled if
desired.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/ath9k/main.c b/drivers/net/wireless/ath9k/main.c
index 7d9a263..7566044 100644
--- a/drivers/net/wireless/ath9k/main.c
+++ b/drivers/net/wireless/ath9k/main.c
@@ -2132,9 +2132,8 @@
(curchan->band == IEEE80211_BAND_2GHZ) ?
CHANNEL_G : CHANNEL_A;
- if (conf->ht.enabled) {
- if (conf->ht.channel_type == NL80211_CHAN_HT40PLUS ||
- conf->ht.channel_type == NL80211_CHAN_HT40MINUS)
+ if (conf_is_ht(conf)) {
+ if (conf_is_ht40(conf))
sc->tx_chan_width = ATH9K_HT_MACMODE_2040;
sc->sc_ah->ah_channels[pos].chanmode =
@@ -2142,7 +2141,7 @@
conf->ht.channel_type);
}
- ath_update_chainmask(sc, conf->ht.enabled);
+ ath_update_chainmask(sc, conf_is_ht(conf));
if (ath_set_channel(sc, &sc->sc_ah->ah_channels[pos]) < 0) {
DPRINTF(sc, ATH_DBG_FATAL, "Unable to set channel\n");
diff --git a/drivers/net/wireless/ath9k/rc.c b/drivers/net/wireless/ath9k/rc.c
index 1b71b93..0686a7c 100644
--- a/drivers/net/wireless/ath9k/rc.c
+++ b/drivers/net/wireless/ath9k/rc.c
@@ -875,7 +875,7 @@
* above conditions.
*/
if ((sc->hw->conf.channel->band == IEEE80211_BAND_2GHZ) &&
- (sc->hw->conf.ht.enabled)) {
+ (conf_is_ht(&sc->hw->conf))) {
u8 dot11rate = rate_table->info[rix].dot11rate;
u8 phy = rate_table->info[rix].phy;
if (i == 4 &&
@@ -1511,7 +1511,7 @@
tx_info, &is_probe, false);
/* Check if aggregation has to be enabled for this tid */
- if (hw->conf.ht.enabled) {
+ if (conf_is_ht(&hw->conf)) {
if (ieee80211_is_data_qos(fc)) {
u8 *qc, tid;
struct ath_node *an;
diff --git a/drivers/net/wireless/ath9k/xmit.c b/drivers/net/wireless/ath9k/xmit.c
index e28889b..9e910f7 100644
--- a/drivers/net/wireless/ath9k/xmit.c
+++ b/drivers/net/wireless/ath9k/xmit.c
@@ -1690,7 +1690,7 @@
(sc->sc_flags & SC_OP_PREAMBLE_SHORT) ?
(bf->bf_state.bf_type |= BUF_SHORT_PREAMBLE) :
(bf->bf_state.bf_type &= ~BUF_SHORT_PREAMBLE);
- (sc->hw->conf.ht.enabled && !is_pae(skb) &&
+ (conf_is_ht(&sc->hw->conf) && !is_pae(skb) &&
(tx_info->flags & IEEE80211_TX_CTL_AMPDU)) ?
(bf->bf_state.bf_type |= BUF_HT) :
(bf->bf_state.bf_type &= ~BUF_HT);